Drilling line

Morbidelli Zenith F2 x 2 Mahros Brush SFx2

Condition: new, Year of construction: 2025, Pressure blasting cabin DSK 11.11.30. Blasting chamber W=1050 D=1050 H=955mm. 1 TÜV-tested pressure vessel 30l with conical outlet funnel. 1 blasting medium dosing valve with blasting medium quantity regulation pneumatically controlled. 1 built-in closing cone with guide tube. 1 compressed air connection with pneumat. Shut-off valve and branch for control air. 1 pressure regulator to adjust the blasting pressure. 1 blasting hose DN19. 1 handpiece with boron carbide blasting nozzle Venturi 8mm. 1 pair of blasting gloves. Electrical height adjustment of the cabin for body-friendly posture. Memory position storage for 3 heights. Dust extraction filter 2000m³/h 2,2kW. Hedpfx Aksga Ehbsrjl

Condition: refurbished (used), FULL LINE of Drilling, max working width mm 3200, with fast automatic handling equipment. Composed of the following machines: A) LOADER (Portal) "RBO" Winner C 3200 with double pick-up and central motorized rollers table. With 2 on-ground motorized rollers ways to in-feed the piles (stacks) of panels to loader. B) TRANSFER (Connecting Rollers Table with 90° conveyoring belts) “RBO” Mod. Transfer TA 90° C) 1st Auotmatic BORER "BIESSE" Mod. Techno FDT with No. 2 Horizontal Units + No. 7 Vertical Bottom Units D) 2nd Automatic BORER "BIESSE" Mod. Techno FDT with No. 2 Horizontal Units + No. 7 Vertical Bottom Units E) TRANSFER (Connecting Rollers Table with 90° conveyoring belts) “RBO” Mod. Transfer TA 90° G) UNLOADER-STACKER (Portal) "RBO" Winner SC 3200 with double pick-up, with double storage station, with central motorized rollers table. With 2 on-ground motorized rollers ways to out-feed the piles (stacks) of panels from the Unloader Hedpfodfgg Iex Akrel

Year of construction: 1988, condition: repair required (used), mechanisation for planer infeed -For lengths up to ca. 13 m -Ideal unit for KVH (solid construction timber)and BSH (laminated beams) in front of the planer -1 operator -lateral destacking unit -separation -4 cross cut saws -cutting cross section 180x220 mm, 150x300 mm Hodpfx Akevbtpjrsl

Year of construction: 2013, condition: ready for operation (used), Connected load: 4kW, weight: 1t. Hsdpohlp Efofx Akrel

Year of construction: 1999, condition: excellent (used), Glass tilting and transport table TRIULZI-IG Hydraulic With castor rollers Hedpfx Akeiy Dtbjrol Rollers are moving down for 360 degree glass movement (for sealing) 3600 mm length and 2400 mm working height Good working order Good condition As is Available immediately

Condition: good (used), Year of construction: 1994, 2 side planer top - bottom constant table ( always same infeed height ) max. planing width 600 mm max. planing height 280 mm planing shafts with strip knives immediately ready for use Hedpfxohuthye Akrsl

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. Hsdpfx Aovf E Avekrjl We accept no liability for the technical specifications or any errors.

Condition: excellent (used), Year of construction: 2006, Clamping force: 500 t Screw diameter: 80 mm Platten dimensions: 1300 x 1200 mm Distance between tie bars V: 900 mm Distance between tie bars H: 900 mm Shot volume: 1779 cm3 Shot weight: 1620 g Injection pressure: 1855 bar Working hours: 46.511 Type: Horizontal Drive: Hydraulic Hjdpfxeva H Amo Akrjl

Condition: excellent (used), Year of construction: 2019, machine/vehicle number: AK26-015, number of ink cartridges: 8, total length: 4,400 mm, total width: 4,400 mm, total height: 1,820 mm, input voltage: 380 V, overall weight: 4,400 kg, product height (max.): 50 mm, Equipment: cooling unit, documentation/manual, Hybrid UV Inkjet printer for sheet and roll materials. Print resolution: 1200 dpi Modulation of the print droplet: Binary, Gray balance Number of colors: 6 colors - CMYK Lc Lm Additional white color that is printed before colored colors (underprint) Drying of all colors using LED lamps Hjdjqlahtepfx Akrol Dot size on the printhead: 7-14-21 picoliters Maximum material thickness: 50 mm Maximum width of printing on plate materials: 3,500 mm The possibility of simultaneous printing of two plates next to each other Display table for receiving plate materials with a length of 2,200 mm Maximum print width on roll material: one roll 3,470 mm, two rolls next to each other 1,625 mm Maximum weight of material in a roll: 350 kg Maximum roll diameter: 350 mm Supports for two rolls of length 3,470 mm on the input and display

Year of construction: 2008, condition: ready for operation (used), functionality: fully functional, Wemhöner Basic 1000 Plus - Year of manufacture: 2008 - Very good condition, little used * Type: KT-MB-28/15-240 * With automatic pin system and inline turner * 2 tables with automatic Vario-Pin system * Teflon coating for pre-glued foil * Foil laying system for pin table (pre-glued foil) * Heating plate size: 2800 x 1500 mm * Max. workpiece size: 2,540 x 1,250 mm Hedpfx Ajxbcudjkrsl * Membrane: Yes * Cutting station * Foil storage carousel, 3.2 m height with 14 hanging bars * PLC control: Siemens S7 * Control panel for Siemens TP 270 PLC (touchscreen) * Automatic membrane tensioning * Installed power supply: 38.5 kW * Max. chamber pressure: 6 bar * Max. pressing opening: 150 mm * 6 cylinders with Ø 125 mm * Operating voltage: 400V 50/60Hz * Press chamber height: 40/60 mm * Max. pressing force: 2400 kN * Operating pressure of hydraulic system: 320 bar