Used Cantilever Arm Shelf for sale (13,342)

Condition: as good as new (ex-display), Year of construction: 2024, Cantilever rack with roof support: Hot-dip galvanized screw system Scope of delivery: 7 rack supports, height 4,230 mm with foot section, usable depth 1,200 mm 21 cantilevers with 1,200 mm usable depth, with deflector 7 roof supports with 1,500 mm projection, pre-drilled for on-site roof construction (*Without wooden purlins and trapezoidal sheets for the roof construction) Including longitudinal and diagonal braces for 1,900 mm stand spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Detailed description: - Stable steel construction made of IPE profiles - Surface of all components hot-dip galvanized - Load capacity per stand 2,700 kg plus roof, wind and snow loads Dkodeh R Taqepfx Ahxeu (Maximum snow load 1.85 kN/m² and wind load zone 2) - Load capacity per cantilever arm 900 kg - including roof support (Maximum snow load 1.85 kN/m² and wind load zone 2) - Cantilever arms height adjustable in 100 mm increments - 3 screwable cantilever arms per stand with a depth of 1,200 mm, with deflectors = 4 storage levels one above the other - Including longitudinal and diagonal braces with 1,900 mm axle spacing - Shelf length: 11,500 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is packed sensibly to enable easy unloading. The subsurface must be made of concrete, level, dowel-capable and able to bear the loads. The customer must check and ensure that the soil condition and load-bearing capacity as well as any official permits required are obtained. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and is not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm from the top edge of the stand.

Condition: good (used), Cantilever rack OHRA 3 m high Over 100 m in stock, see pictures. Height 3 m high Boom 100 cm Load capacity/boom 800 kg 4,5 running meters, 4 pcs. uprights with outrigger Negotiation price: € 2.160,-- /net Offer consists of: 4 pcs. uprights with foot 3 m high 4 adjustable outriggers, each upright 100 cm, load capacity 800 kg/outrigger. Diagonal braces, stiffeners and distances are included. Frame spacing 150 cm Load capacity per upright per side 3.200 kg Dkodpfxjcd Dwyj Ahxou Height of 2.5 m, 4 m or 6 m available Other composition on request: Constantly over 3000 running meters of pallet racks from numerous manufacturers in stock. Transport and assembly available on request. (Changes and errors in the technical data, specifications and prices and prices and subject to prior sale! See our terms and conditions, all prices excl. VAT ex stock) Purchase / Sale We are constantly looking for, or offer numerous items from various fields broom-clean business evacuations Business resolutions Fast - flexible - ready to hit! We clear and - or dispose also for liquidators. Write us with some keywords, we will contact you immediately. To get to our site please click on our logo!

Condition: like new (used), Year of construction: 2025, Cantilever rack with roof support: Hot-dip galvanized screw system Scope of delivery: 7 rack supports, height 4,230 mm with foot section, usable depth 1,200 mm 21 cantilevers with 1,200 mm usable depth, with deflector 7 roof supports with 1,500 mm projection, pre-drilled for on-site roof construction (*Without wooden purlins and trapezoidal sheets for the roof construction) Including longitudinal and diagonal braces for 1,900 mm stand spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Detailed description: - Stable steel construction made of IPE profiles - Surface of all components hot-dip galvanized - Load capacity per stand 2,700 kg plus roof, wind and snow loads (Maximum snow load 1.85 kN/m² and wind load zone 2) - Load capacity per cantilever arm 900 kg - including roof support (Maximum snow load 1.85 kN/m² and wind load zone 2) - Cantilever arms height adjustable in 100 mm increments - 3 screwable cantilever arms per stand with a depth of 1,200 mm, with deflectors = 4 storage levels one above the other Dkjdpjmhhy Nefx Ahxsu - Including longitudinal and diagonal braces with 1,900 mm axle spacing - Shelf length: 11,500 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is packed sensibly to enable easy unloading. The subsurface must be made of concrete, level, dowel-capable and able to bear the loads. The customer must check and ensure that the soil condition and load-bearing capacity as well as any official permits required are obtained. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and is not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm from the top edge of the stand.

Condition: new, OHRA cantilever rack Negotiated price: € 5.940,00 net ex stock You are bidding on a rack with a length of 7.5 m, consisting of 6 uprights with base, 6 m high + 4 adjustable outriggers per upright (120 cm), load capacity 900 kg/outrigger. Diagonal bracing, stiffeners and spacers are included. Bridges, grids and chipboards are available separately at an extra charge! Frame spacing 150 cm Arm length / outrigger 120 cm Load capacity 900 kg / outrigger Load capacity per upright per side 3,600 kg Over 100 meters available. Heights of 2.5 m, 3 m or 4 m available. Other combinations on request. Dkedpeby Uunsfx Ahxou (Subject to changes and errors in the technical data, specifications and prices as well as prior sale reserved! See our GTC, all prices excl. VAT ex stock) Purchase / Sale We are constantly looking for or offering numerous items from various areas Machines from all industries Remaining stock Special items swept clean company clearances Business liquidations Purchase of remaining stock Fast - flexible - ready for action! We also clear and or dispose of for liquidators. Write to us with a few keywords and we will get back to you as soon as possible.

Condition: like new (used), Year of construction: 2025, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 rack uprights, height 4,160 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Longitudinal and diagonal struts for 4,000 mm rack length (distance 1,300 mm) Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) Dkedpfx Ajmhhf Sshxsu - (*Offer available in larger quantities: approx. 90 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Surface hot-dip galvanized - Rack height 4,160 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm Usable depth - Cantilever arms height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is packed sensibly to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and suitable for dowels and must be able to absorb the loads. The customer must check and ensure that the floor conditions and load-bearing capacity, as well as any official permits that may be required, are obtained. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and is not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 4,160 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Longitudinal and diagonal struts for 4,000 mm shelf length (distance 1,300 mm) Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 90 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Surface hot-dip galvanized - Shelf height 4,160 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm Usable depth - Cantilever arms height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm Djdpfx Asd Tqalshxoku - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is packed sensibly to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and suitable for dowels and must be able to absorb the loads. The customer must check and ensure that the floor conditions and load-bearing capacity, as well as any official permits that may be required, are obtained. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and is not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 4,160 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Longitudinal and diagonal struts for 4,000 mm shelf length (distance 1,300 mm) Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 90 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) Djdsmhh Dtepfx Ahxeku - Surface hot-dip galvanized - Shelf height 4,160 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm Usable depth - Cantilever arms height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is packed sensibly to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and suitable for dowels and must be able to absorb the loads. The customer must check and ensure that the floor conditions and load-bearing capacity, as well as any official permits that may be required, are obtained. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and is not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Used cantilever racking: Screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights Height 4,160 mm with base section 1,200 mm usable depth 12 cantilever arms with 1,200 mm usable depth, standard Longitudinal and diagonal braces for 4,000 mm shelf length (spacing 1,300 mm) Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 90 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 4,160 mm - Load capacity per upright 2,250 kg - Base section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm Djdpfx Ahofdkb Tsxjku - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2025, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 rack stands, height 3,500 mm with base section 1,200 mm 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 stands in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Rack height 3,500 mm - Load capacity per stand 2,250 kg - Base section and cantilevers with 1,200 mm usable depth - Cantilevers in 100 mm increments height adjustable - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) Djdpfxefdkb Us Ahxsku - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 3,500 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) Dodpfomhh Dhjx Ahxjku - Hot-dip galvanized surface - Shelf height 3,500 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm usable depth Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 rack stands, height 3,000 mm with base section 1,200 mm 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Rack height 3,000 mm - Load capacity per stand 2,250 kg - Base section and cantilevers with 1,200 mm usable depth Dksdpjfdkbhofx Ahxou - Cantilevers in 100 mm increments height adjustable - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: Dkjdpemhhyaefx Ahxsu 4 shelf uprights, height 2,600 mm with foot section, 1,000 mm usable depth 12 cantilevers with 1,000 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 2,600 mm - Load capacity per upright 1,800 kg - Foot section and cantilever arms with 1,000 mm usable depth Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 3,000 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 3,000 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm usable depth Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. Djdpfxjmhhx Ij Ahxeku The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 rack stands, height 2,600 mm with base section 1,000 mm Dkedpod Tbbdofx Ahxeu 12 cantilevers with 1,000 mm depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 90 stands in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Rack height 2,600 mm - Load capacity per stand 1,800 kg - Base section and cantilevers with 1,000 mm usable depth - Cantilevers in 100 mm increments height adjustable - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is packed sensibly to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2024, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 rack stands, height 3,000 mm with base section 1,200 mm 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Rack height 3,000 mm - Load capacity per stand 2,250 kg - Base section and cantilevers with 1,200 mm usable depth - Cantilevers in 100 mm increments height adjustable - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. Dedpfxjguk Dkj Ahxeku When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 3,000 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 3,000 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm usable depth Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. Dedjmhh Anspfx Ahxoku The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 rack stands, height 2,600 mm with base section 1,000 mm 12 cantilevers with 1,000 mm depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 90 stands in stock) Dedpfxsguk Dve Ahxjku Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Rack height 2,600 mm - Load capacity per stand 1,800 kg - Base section and cantilevers with 1,000 mm usable depth - Cantilevers in 100 mm increments height adjustable - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is packed sensibly to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 2,600 mm with foot section, 1,000 mm usable depth 12 cantilevers with 1,000 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 2,600 mm - Load capacity per upright 1,800 kg - Foot section and cantilever arms with 1,000 mm usable depth Cantilever arms in Height adjustable in 100 mm increments Dkedpfxjmhh Dze Ahxeu - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2024, Cantilever rack in painted version (RAL 7016 anthracite): Scope of delivery: 4 rack uprights, height 4,200 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth Longitudinal and diagonal struts for 1,300 mm rack axis spacing (4,000 mm rack length) Fastening material (screws, nuts and washers) - (*No paint damage!) - (*No damaged components!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 50 racks in stock) Net price: €1,990.00 plus VAT Detailed description: - Stable steel construction made of IPE profiles (screw system) - Surface painted in RAL 5010 (gentian blue) - Rack height 4,200 mm - Load capacity per stand 2,200 kg - Base and cantilever arms with 1,200 mm usable depth - Cantilever arms height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 730 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without floor anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. Dkodomidyfjpfx Ahxou Delivery can take place in approx. 1 - 2 weeks after receipt of the order. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-compatible and must be able to bear the loads. The customer must check and ensure that the soil condition and load-bearing capacity as well as any official permits that may be required are obtained. The shelf supports must be anchored to the ground on site; anchoring to the wall is not necessary and is not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm from the top edge of the stand.

Condition: like new (used), Year of construction: 2024, Screw system in hot-dip galvanized design: Pick-up price: Sturdy steel construction made of IPE profiles Shelf height 3500 mm Load capacity per upright 2100 kg Foot section 1200 mm usable depth Cantilever arms height-adjustable in 100 mm increments Dkedpfjmhhl Hjx Ahxju 3 screw-on cantilever arms per upright Usable depth 1200 mm, standard (= 4 levels) Load capacity per cantilever arm 700 kg Including longitudinal and diagonal bracing Including fastening material (without ground anchors) With assembly instructions and load plates C4 according to DIN standard

Condition: like new (used), Year of construction: 2024, Cantilever rack double-sided used: Hot-dip galvanized screw system Scope of delivery: 4 double-sided shelf uprights, height 3,500 mm with foot parts each 1,200 mm 24 cantilevers with 1,200 mm depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Also available in larger quantities: 20 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles Dodpfxsmkixwj Ahxeku - Surface of all components hot-dip galvanized - Load capacity per upright side 2,250 kg - Load capacity per cantilever arm 750 kg - Cantilever arms height adjustable in 100 mm increments - 6 screwable cantilevers per upright and 2 foot parts with a depth of 1,200 mm, standard = 4 storage levels one above the other per stand side - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2024, Cantilever rack double-sided used: Hot-dip galvanized screw system Scope of delivery: 4 double-sided shelf stands, height 4,160 mm with foot section 1,200 mm Dkedpfx Ash Ek Dajhxeu 24 cantilevers with 1,200 mm depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Also available in larger quantities: 20 stands in stock) Detailed description: - Stable steel construction made of IPE profiles - Surface of all components hot-dip galvanized - Load capacity per stand side 2,250 kg - Load capacity per cantilever arm 750 kg - Cantilever arms height adjustable in 100 mm increments - 6 screwable cantilever arms per stand and 2 base sections with a depth of 1,200 mm, standard = 4 storage levels one above the other per side of the stand - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: as good as new (ex-display), Year of construction: 2024, Cantilever rack in painted version (RAL 7016 anthracite): Scope of delivery: 4 shelf uprights height 2.56 m with base section 1.0 m usable depth (1.2 m total depth) 12 cantilever arms with 1.0 m usable depth Longitudinal and diagonal braces for 4 m shelf length (spacing 1.3 m) Fastening material (screws, nuts and washers) (*No paint damage!) Net price on collection: € 1,490.00 plus VAT. Delivery possible for an additional charge Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Surface painted in RAL 7016 (anthracite) - Shelf height 2,560 mm - Load capacity per upright 1,800 kg - Foot section and cantilever arms with 1,000 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Made in Germany - Short delivery time - On-site collection possible Dodpfx Ahjguk A Hoxjku Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. The substrate must be made of concrete, be level and suitable for dowels and be able to bear the acting loads. The customer is responsible for checking and ensuring the ground conditions and load-bearing capacity as well as any official approvals required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: as good as new (ex-display), Year of construction: 2024, Cantilever rack in painted version (RAL 7016 anthracite): Scope of delivery: 4 shelf uprights height 4,200 mm with base section 1,200 mm usable depth 12 cantilever arms with 1,200 mm usable depth Longitudinal and diagonal braces for 1,300 mm upright center distance (4,000 mm shelf length) Fastening material (screws, nuts and washers) - (*Delivery or collection in approx. 1 - 2 weeks) - (*No damage to paintwork!) - (*No damaged components!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Net price: € 1,990.00 plus VAT. Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Surface painted in RAL 7016 (anthracite) - Shelf height 4,200 mm - Load capacity per upright 2,200 kg - Foot section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 740 kg Dedpfx Ahemhhypjxsku - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. Delivery can be made in approx. 1 - 2 weeks after receipt of order. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The surface must be concrete, level and suitable for dowels and must be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any necessary official approvals are in place. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: excellent (used), Cantilever transport trolley Workshop trolley Height 1650 mm width 780 mm Dksdpfx Aepkx Scehxou Depth 600 mm length of support arms 300 mm sturdy design