Used Cantilever for sale (201)

Condition: like new (used), Year of construction: 2025, Used cantilever racking: Screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights Height 4,160 mm with base section 1,200 mm usable depth 12 cantilever arms with 1,200 mm usable depth, standard Longitudinal and diagonal braces for 4,000 mm shelf length (spacing 1,300 mm) Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 90 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 4,160 mm - Load capacity per upright 2,250 kg Hjdpfx Aofdkb Tobzjw - Base section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: as good as new (ex-display), Year of construction: 2023, Short & sweet Base axis (X) : 1.3-2 mm Cantilever (Y) : 1.3-4 mm Accuracy : 0.06 mm Technical data Linear axis accuracy : ± 0.1 mm/m Maximum travel speed : 10 m/min Acceleration : 0.02 g Repeat accuracy : ± 0.06 mm Circularity : ± 0.1 mm Z-axis stroke : 180 mm Base axis (X) : 1.3 m, 3 m, 4 m Extension arm (Y) : 1.3 m, 2 m Equipment and accessories Maintenance packages UltraPierce tapping aid1 Splash guard1 Hjdpfx Abshw Nfqjzjw FlowTexturing (FTT) Abrasive de-sludging system ecoFlow FlowNest* FlowXpert* Laser pointer Clamping and tensioning system Clean water conversion kit * Required for FlowTexturing

Condition: as good as new (ex-display), Year of construction: 2024, Optimum OPTIdrill RD 6 Precise, solid radial drilling machines of top quality. Ideal for versatile use in single-part and series production. • Versatile application range, such as drilling, reaming, and threading • Electrically braked motor • 24V DC electrical system and 2-channel safety chain according to DIN EN 12717 • Heavy, solid, high-quality cast iron • Wide reach thanks to horizontally adjustable machine head • Clearly arranged control panel • Smooth-running swivel and travel axes • Elaborately machined column swivel with optimized clamping for maximum stability and minimal clamping offset • Robust, torsion-resistant boom construction • Boom height adjustment via powerful motor drive and lifting spindle • Drill head gear running in an oil bath Hsdpswa Tc Sofx Abzsw • Boom guideways hardened and precision-ground • Chrome-nickel steel gears, hardened and precision-ground, ensuring quiet and smooth operation • Drill head and column can be clamped together or separately or loosened • Right-left rotation • Solid, precise drilling table, generously dimensioned • Hardened and ground clamping table with parallel T-slots • Machine light • Overload protection • Thick-walled cast iron column ensures smooth operation and stability • LED lamp • Coolant system with coolant tank in the machine base RD 6 / RD 7 • Column is hydraulically clamped Dimensions and Weights Column diameter 320 mm Length approx. 2670 mm Width/Depth approx. 1120 mm Height approx. 2760 mm Weight approx. 3200 kg Extension arm Rotation angle 180° Drilling capacity Drilling capacity steel (S235JR) 50 mm Continuous drilling capacity steel (S235JR) 45 mm Drilling table T-slot size 14 mm T-slots Number: 4 T-slot spacing: 180 mm Maximum distance between spindle and drilling table: 1420 mm Clamping table length: 630 mm Clamping table width: 500 mm Clamping table height: 500 mm Clamping table T-slot size: 22 mm Number of T-slots on the clamping table: 3 Clamping table T-slot spacing: 150 mm Min. distance between spindle and clamping table: 0 mm Max. distance between spindle and clamping table: 910 mm Min. distance between spindle and drilling table: 465 mm Speed range: Speed range: 44 – 1023 rpm Number of speed ranges: 12 Electrical data: Total power consumption: 6.5 kW Connection voltage: 400 V Mains frequency: 50 Hz Machine base: Working surface length: 2550 mm Working surface width: 970 mm Motor(s) Spindle motor drive power: 4 kW Drive power Cantilever arm lifting motor 1.5 kW Coolant pump power of drive motor 90 W Hydraulic clamp drive 0.75 kW Spindle Quill stroke 270 mm Spindle mount MT5 Quill feed speed 0.06 – 0.2 mm/rev Quill feed speeds 3 Travel path Drill head travel (horizontal) 1250 mm Arm stroke (vertical) 680 mm Maximum spindle-column distance 1600 mm Minimum spindle-column distance 350 mm

Year of construction: 2018, condition: as good as new (ex-display), Technical Specifications • Space-saving fixed table - moving gantry design for small machine footprint • Single structure welded, stress relieved and machined all-steel base frame, gantry and gantry feet • Steel structures are reinforced with heavy ribs to resist flex and dampen vibrations • Each machine design is efficiently optimized and validated by using Finite Element Analysis (FEA) to ensure quality, performance, and safety • Open machine bed for easy loading and unloading by forklift or overhead crane • High preload profiled linear bearings with cover strips on all axis • Brushless digital A/C servo drives and motors on all axis • Dual side drive and synchronized X-axis; no twist under load like applicable to a single center-mounted ball screw or cantilevered design • Rack and pinion drive system on X and Y axis • High precision ball screw on Z axis (anchored at both ends) • Low-backlash planetary gear boxes • Fully closed cable carriers prevent the cables from damage by chips and fine dust • High quality, shielded cables for energy chains are a guarantee of reliability • Work area X axis 3,050 mm • Work area Y axis 1,550 mm • Z-axis clearance 200 mm • Z-axis travel 280 mm • Maximum feed rate 80 m/min • Network connection via Ethernet • Remote Administration via Internet • Dimensions approx. 3,460 x 2,460 x 1,930 mm (L x W x H, without safety devices) • Weight approx. 3,500 Kg CNC Control System • Siemens Sinumerik 808D Advanced • Color LCD display • IP65 protection for CNC front panel and machine control panel • Preassigned keys for common functions, such as handwheel selection, tool change, coolant control or program testing • 7-segment display for tool number • Spindle control with spindle override (rotary switch with 15 positions) and feedrate / rapid traverse Portable MPG with handwheel, axis selector and resolution switch, E-stop button • Fast data transmission via USB stick (on the operator panel front) and high-speed Ethernet Interface Servo Motors and Drives • Siemens Sinumerik Digital Field Bus • Siemens SINAMICS V70 servo drives • Siemens SIMOTICS S-1FL6 servo motors • Siemens pre-assembled MOTION-CONNECT cables Automatic Tool Change Spindle • Spindle power 8 KW (S1) / 10 KW (S6) • Maximum speed 24,000 RPM (software controlled) • Ceramic bearings • Electric fan for cooling • Toolholder ISO-30 • Max. 26 mm (1 1/4") tool diameter with ER-40 tool holders • Temperature sensor • Safety interlock for tool in spindle • Air pressure sensor Dust Collector for Automatic Tool Change Spindle • Hose diameter 120 mm • Manual height adjustment • Pneumatic operation Tool Magazine • Linear tool rack, mounted outside of work area at the backside of the machine • Maximum 12 tool positions possible • 4 fool holders ISO30 / ER32 are included Hedpoflpmdsfx Abzjw 6 Zone Vacuum Table • Phenolic work surface (thickness 25 mm) with grid • Zones individually valved High pressure vacuum pump according to customer requirements Precision Tool Length Sensor CE Package Delivery, commissioning & training as per requirements

Condition: used, Cut-to-length line Pro-Eco with Cassette Type Precision Leveler 60 x .187 x 50,000Lbs (A3789) Maker: Pro-Eco Excellent conditions SPECIFICATIONS: MAX WIDTH 60" MAX THICKNESS 187" MANUFACTURER - PRO-ECO YEAR - 1985, REINSTALLED 2002 WIDTH RANGE - 8" to 60" GAUGE RANGE - .024" to .187" WEIGHT CAPACITY - 50,000# (25 TON) COIL OD - 36" to 72" COIL ID - 19" to 24" SHEET LENGTH - 24" to 168" SHEET WIDTH - 8" to 62" PACK HEIGHT - 30" (INCLUDING DUNNAGE) Hjdpfothg Disx Abzow PACK WEIGHT - 20,000# LINE DIRECTION - RIGHT to LEFT LINE SPEED - 50 to 300 FPM (VARIABLE) LEVELER TYPE - MECHANICAL WEDGE STYLE w/ TWO CASSETTES LINE COMPONENTS: FOUR ARM ENTRY STORAGE TURNSTILE FLOOR LEVEL COIL LOADING CAR CANTILEVERED MANDREL UNCOILER w/ WATER COOLED BRAKE PIVOTING AND TELESCOPING PEELER BLADE ENTRY PINCH ROLLS ROLLER TYPE SIDE GUIDES ENTRY CROP SHEAR SIDE TRIMMER HYDRAULIC SERVO DRIVE (CURRENTLY NOT OPERATIONAL) MECHANICAL STYLE LEVELER FRAME W/ 200 HP MOTOR CASSETTE #1 - 19 ROLL, 2.50" DIAMETER, 5 HI, 7 BACKUP FLIGHTS CASSETTE #2 - 19 ROLL, 1.75" DIAMETER, 5 HI, 7 BACKUP FLIGHTS STRIP INSPECTION AND CARRY-OVER TABLE w/ NON-MARKING ROLLS LOOPING PIT QUADRANT TABLES w/ NON-MARKING ROLLS ROLLER TYPE STRIP SQUARING TABLE PRECISION ROLL FEEDER W/ 55 HP MOTOR HIGH SPEED MECHANICAL CUT OFF SHEAR W/ 40 HP MOTOR BLANK INSPECTION CONVEYOR w/ NON-MARKING BELT REJECT BELT CONVEYOR w/ NON-MARKING BELT AND SCRAP CART 14 FOOT AIR FLOAT STACKER w/ SQUARING GUIDES AND END STOP 14 FOOT STACKER LIFT CONVEYOR w/ END DISCHARGE ROLLERS 14 FOOT STACKER RUNOUT CONVEYOR w/ END DISCHARGE ROLLERS OPERATOR CONTROL STATIONS UPDATED AC CONTROLS w/ ALLEN BRADLEY "CONTROL LOGIX" PLC (2006) UPDATED DRIVE CONTROLS w/ SIEMENS "SIMOREG" CONTROLLERS (2006) CLOSED LOOP HYDRAULIC SYSTEM CLOSED LOOP WATER COOLING SYSTEM

Year of construction: 2012, condition: good (used), machine/vehicle number: ENOG, DEMAG KBK crane headliner crane runway dimensions approx. 8x4m Payload / lifting load 250 KG - 0.25to Technical data of the system: Crane runway made from Demag KBK1+2 rails The system is delivered complete: KBK rails, rail connectors, trolleys, end plates, cable carriers, holders/hangers, etc. incl. Demag DC-COM 250KG chain hoist Hedpfx Aemqf Nfjbzsw Crane is dismantled and available immediately Used condition, see pictures Item location is 75053 Gondelsheim Dispatch by forwarding agent or pick-up only by appointment Demag KBK1 KBK2 and KBK3 rails are stock items! Other KBK systems are also available. Payload 125KG - 1600KG Please inquire about your crane runway with cantilever load and dimensions.

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 3,500 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) Hsdpsmhh Dhjfx Abzow - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 3,500 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm usable depth Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: used, Cantilever racking, heavy duty racking Hodpfjd Eqlpox Abzew consisting of: -Shelf: with 2 stands each -Support arms: double-sided -6x ledger depths: 900/500/400/300/230 mm -welded -Also: other quantities and heights available on request -Number: 1x shelves available -Transport dimensions: 2100/2020/H2170 mm -Own weight: 430 kg/piece

Condition: new, Holzkraft FKS 550-3200 PRO sliding table saw 5200550 Heavy-duty sliding table saw with scoring unit Saw blade tilt and height adjustment is manual Max. cutting height 200mm Scoring unit with separate drive motor Main saw blade with belt drive and speeds 2800/3665/4800 min¯¹ High dead weight ensures vibration-free running Large cantilever table with material roller Rip fence with round bar guide Extendable aluminum longitudinal fence with two folding stops 7.5 kW main motor mounted on robust cast iron frame Quadruple-mounted format sliding carriage made of anodized aluminum with high torsional rigidity Multiple locking device on the sliding table Table widening and table extension made of strong sheet metal as standard equipment Large pendulum protection hood can be conveniently swung up by means of a gas pressure spring Saw blade clamping via tool-free Rapid system Hjdpekknaasfx Abzew TECHNICAL DATA: Dimensions and weights Length (product) approx. 3386mm width/depth (product) approx. 3703mm Height (product) approx. 1330mm Weight (net) approx. 1102kg Connection suction Suction port diameter 120mm Suction port diameter saw blade guard 80mm Electrical data Supply voltage 400V Mains frequency 50Hz input power 7,5kW Output power 6kW Motor speed 2800min¯¹ Sliding carriage and table sliding table length 3200mm sliding table width 416mm height of sliding table 890mm Table length 1255mm Table width 685mm Noise emission Sound pressure level 96,5dB(A) Circular saw unit Cutting width with rip fence 1450mm Max. Cutting width to the left of the saw blade 3200mm Saw blade inclination 90 - 45 Max. Cutting height 90°200mm Max. cutting height Cutting height 45°140mm Diameter saw blade 550mm Speed saw blade 2800/3665/4800 min¯¹ Scoring unit Diameter scoring saw blade 120 - 130mm Speed scoring saw blade 8000min¯¹ Holkraft dealer - accessories available on request!

Year of construction: 2017, condition: as good as new (ex-display), Technical Specifications • Space-saving fixed table - moving gantry design for small machine footprint • Single structure welded, stress relieved and machined all-steel base frame, gantry and gantry feet • Steel structures are reinforced with heavy ribs to resist flex and dampen vibrations • Each machine design is efficiently optimized and validated by using Finite Element Analysis (FEA) to ensure quality, performance, and safety • Open machine bed for easy loading and unloading by forklift or overhead crane • High preload profiled linear bearings with cover strips on all axis • Dual side drive and synchronized X-axis; no twist under load like applicable to a single center-mounted ball screw or cantilevered design • Rack and pinion drive system on X and Y axis • High precision ball screw on Z axis • Low-backlash planetary gear boxes • Fully closed cable carriers • High quality, shielded cables • Work area X axis 3,050 mm • Work area Y axis 1,550 mm • Z-axis clearance 280 mm • Z-axis travel 480 mm • Maximum feed rate 80 m/min • Network connection via Ethernet • Remote Administration via Internet • Weight approx. 4,000 Kg CNC Control System • FlexiCAM ACS Control System Pro • Powerful industrial CNC control system “Made in Germany” • DIN-ISO 66025 G-Code compatible • Graphical CNC simulation • Industrial PC with 17” Touchscreen display as HMI • User-friendly machine control panel with mode selectors and function keys • Spindle control with spindle override and feedrate / rapid traverse override (rotary switches) • Portable MPG with handwheel, axis selector and resolution switch, E-stop button • Windows keyboard and mouse • Fast data transmission via USB stick (on the operator panel front) and high-speed Ethernet Interface • Remote Support via Internet • Touchscreen and machine control panel are integrated into enclosure Servo Motors and Drives • Digital servo drives with AC servo motors • High resolution absolute encoders (17 bit) • EtherCAT fieldbus Automatic Tool Change Spindle • Spindle power 10 KW (S1) / 12 KW (S6) • Maximum speed 24,000 RPM (software controlled) • Ceramic bearings • Electric fan for cooling Hjdpeflpriofx Abzjw • Toolholder HSK-63F • Max. 26 mm (1 1/4") tool diameter • Temperature sensor • Safety interlock for tool in spindle • Air pressure sensor Dust Collector for Automatic Tool Change Spindle • Hose diameter 120 mm • Manual height adjustment • Pneumatic operation Tool Magazine • Linear tool rack, mounted outside of work area at the backside of the machine • Maximum 12 tool positions possible • 4 fool holders HSK-63F / ER40 are included Precision Tool Length Sensor 6 Zone Vacuum Table • Phenolic work surface (thickness 25 mm) with grid • Zones individually controlled High pressure vacuum pump according to customer requirements 4x Popup Pins Automatic Central Lubrication (Grease) CE Package Delivery, commissioning & training as per requirements

Condition: new, Year of construction: 2025, NOTICE: POSSIBILITY OF CALCULATING ANY CRANE CONFIGURATION Thank you for your interest in our offer. WNM Sp. z o.o. offers a wide range of cranes, including: gantry cranes, semi-gantry cranes, cantilever cranes, column-mounted cranes, suspended overhead cranes, and top-running overhead cranes. We invite you to submit inquiries for quotations. Our pricing is based on customer-provided data such as crane type, lifting capacity, lifting height, dimensions, and travel rail length. This advertisement refers to a gantry crane/hoist with a lifting capacity of 5 TONS. All crane components are made from high-quality materials, ensuring durability and resistance to damage even in harsh environments. TECHNICAL SPECIFICATIONS: GANTRY CRANE WITH HOIST – 5 TON CAPACITY Span Length: 6 m Lifting Height: 3.55 m Lifting Mechanism: 5-ton electric chain hoist Lifting Speed: 2.7 m/min Cross Travel Speed: 11 m/min Crane Travel Speed: 10 m/min Work Class: A3 Power Supply: 380V/50Hz/3-Phase Control Mode: Pendant control + remote control Hsdpfjv Ni Rxjx Abzjw We issue VAT invoices for all machines. For any inquiries, please feel free to contact us.

Year of construction: 2009, condition: used, Apple 15 head depositor Hjdpjb Ucwkjfx Abzsw Model: CCP12 Stainless cantilever framed 15 head machine

Condition: like new (used), Year of construction: 2024, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 rack stands, height 3,000 mm with base section 1,200 mm 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) Hjdpfx Ajguk Dkjbzow - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Rack height 3,000 mm - Load capacity per stand 2,250 kg - Base section and cantilevers with 1,200 mm usable depth - Cantilevers in 100 mm increments height adjustable - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: good (used), Year of construction: 2006, operating hours: 14,000 h, functionality: fully functional, machine/vehicle number: AL1/004511, travel distance X-axis: 2,800 mm, travel distance Y-axis: 1,250 mm, travel distance Z-axis: 180 mm, rapid traverse X-axis: 40,000 m/min, rapid traverse Y-axis: 40,000 m/min, rapid traverse Z-axis: 25,000 m/min, feed length X-axis: 2,800 mm, feed length Y-axis: 1,250 mm, feed length Z-axis: 110 mm, nominal power (apparent): 11 kVA, controller manufacturer: ESA, controller model: KVARA 6, workpiece length (max.): 2,900 mm, workpiece width (max.): 1,250 mm, workpiece height (max.): 110 mm, total height: 2,700 mm, total length: 5,500 mm, total width: 2,500 mm, table width: 1,250 mm, table height: 900 mm, table length: 2,750 mm, Working dimension X 2,900 mm Working dimension Y 1,240 mm Working dimension Z 180 mm Number of milling spindles 1 Main motor power 6.6 kW Rotation speed max 18,000 rpm Torque support Tool clamping system HSK-F63 Tool changer positions 8 Vertical drilling spindles 12 Horizontal drilling spindles and X 4 Horizontal drilling spindles and Y 2 Groove saw and X-direction Lock recess milling aggregate double-sided Angular head 0-360+0-90 deg. Vector axis Cantilever machine Machine table Pod and rail table Number of consoles Hjdpfx Abowh I Nvozsw 6 Vacuum pump Number of vacuum pumps 1 Capacity vacuum pump 100 m³/h Safety devices Bumper Interface for .dxf data Control PC control Software SCM XILOG Conformity marking CE mark

Condition: new, functionality: fully functional, Year of construction: 2025, laser power: 20,000 W, travel distance X-axis: 3,500 mm, travel distance Y-axis: 28,000 mm, travel distance Z-axis: 850 mm, positioning speed: 40 m/min, workpiece weight (max.): 35,000 kg, input frequency: 50 Hz, type of input current: three-phase, warranty duration: 24 months, Equipment: CE marking, centralized greasing system, cooling unit, dust extraction, emergency stop, fume extraction, nozzle changer, safety light barrier, NS-12020H PROFILE STEEL LASER CUTTING AUTOMATION LINE Technical Specifications Laser Power: 12000W-20000W X-axis Travel: 3500mm Y-axis Travel: 28000mm (customizable) Z-axis Travel: 800mm A-axis Travel: ±90° C-axis Travel: ±90° U-axis Travel: 30mm Maximum Speed: 40m/min Positioning Accuracy: ±0.1mm Main Features： Simple and Stylish Integrated simple structure with a mobile design. Features a main control panel, laser unit, chiller, electrical cabinet, and cantilever beam structure, all highly integrated for stable mobility and operation. Quality Assurance Precision calibration and compensation of steel profiles. Enables automatic positioning and error detection of steel profiles. High positioning accuracy, low sizing error, and a 100% one-time through-hole rate. Increased Efficiency, Reduced Costs Professional material-checking software enables one-click nesting. Hjdpfx Abjvmwxxjzew Optimizes cutting sequences based on raw materials and component specifications. Automatically joins leftover materials to minimize waste and reduce costs. All-in-One Service Powerful 3D five-axis CNC technology. Supports profile cutting and 45-degree bevel cuts. Adapts to various cutting processes for different applications. Enhanced Quality and Efficiency Seamlessly integrates with TEKLA steel structure design software for professional and efficient operations. Reduces complex modeling processes and saves time on manual drawings. Enables one-click generation of component process codes to significantly boost production efficiency. Smart Management Automated loading and unloading system for streamlined feeding and cutting. Fully automated one-stop workflow. Efficiently completes bulk operations, reducing manual intervention and labor costs.

Condition: new, Aluminum format sliding carriage with hardened steel guide rods. Telescopic crosscut stop 1800 mm with two stop flaps as standard. Stable cantilever table for processing heavy panels. Rip stop with micrometric fine adjustment. Milling spindle and saw blade can be completely retracted. Replaceable milling spindle with MK4 holder With its own motor for the scoring unit for easy switching off. 100% Made in EU (developed, built, quality-tested) Technical data: Circular saw: max. saw blade diameter 315 mm spindle diameter 30 mm max. cutting width on parallel stop 1100 mm max. cutting height, 90°/45° 103 mm/72 mm motor output 5 kW S6 (4 Kw S1) extraction nozzle diameter 120 mm milling machine: spindle diameter 30 mm Hjdpsvrvdqjfx Abzjw pivoting spindle 90°/45° height adjustment of the spindle 175 mm spindle speed 10000/8000/6000/ 5000/4000/3000 motor output 5 kW S6 (4 Kw S1) weight 790 kg With special accessories: format table length 2300 mm, scoring unit, 4 kW Motor, integral stop 500 mm, upper suction, degree grid on the delivery table Special accessories Optional: Change spindle for router Longer format sliding table (2500 - 3200 mm)

Condition: new, Year of construction: 2025, I sell here several machines, devices, etc. for woodworking, forklifts, work platforms, as well as accessories and spare parts. Therefore, they necessarily also note my other auctions! Format circular saw table circular saw carpenter circular saw format saw WH- machines Type: Z45 - 400E Professional New wide aluminum format carriage 320 cm with carbide round bar guide system width approx. 415 mm cantilever table with extendable aluminum cutting fence, incl. 2x folding fence cutting to length up to approx. 300cm Electric height adjustment of the saw blade Stable round bar guide of the saw unit. Electric tilting of the saw blade up to 45 with digital display of the tilting angle. Precise tilting segment guide of the saw unit. rip fence up to 125cm with fine adjustment stable 50 mm round bar guide parallelogram protection device with upper suction can be folded away for standing workpiece cuts. 2 different speeds adjustable ( 4000/ 600rpm) saw blade diameter up to 400 mm Cutting height at 90°: 125 mm Hsdpfx Aeh Hauyobzew Scorer with 120 mm scoring saw blade and electrical height adjustment Engine power main engine 5,5 KW with overload protection and thermal monitoring. Motor power scorer 1,1KW Body made of sturdy 6mm box construction with reinforcement Stable cast iron worktop incl. trimming wedge and eccentric workpiece holder The machine can also be purchased via installment plan with a term of 36 months. This offer is an installment plan leasing offer via the company DLL Leasing with a term of 36 months. Credit check and processing is done by DLL Leasing. Further terms and conditions on request. For further data, delivery times and availability please ask. Depending on availability, the machine can be inspected and tested at our warehouse. prior inspection is expressly desired, just leave tel. no. by mail, then I will get back to you about a viewing appointment. Subject to prior sale, All information without guarantee. The machines can be picked up yourself or shipping by forwarding at the expense of the buyer. Loading and packing can be organized by us. The shipping costs are a guideline, depending on distance and unloading possibility, they may vary, please inquire. An invoice with sales tax will be issued.

Condition: excellent (used), Year of construction: 2016, machine/vehicle number: F32/16, ABUS EHB overhead crane crane runway with cantilever supports Dimensions approx. 8.2m x 4.8m, payload / lifting load 1x 250 KG - 0.25to Technical data of the system: Crane runway made from ABUS HB180 rails Approximate dimensions as follows: External dimensions - space requirement approx. 8.2m x 4.8m with 1 bridge 250KG payload Top supports 4.05m Top rail 3.88m UK running rail 3.70m Upper bridge 3.62m UK bridge 3.46m Hook height 3.05m Track width 3.8m Internal dimensions of supports 4.46 m Hsdpfx Abomi S A Aszew Rail length 8.2m Bridge length 4.4m Base plate of the support 50x50cm Support HEA180 Support spacing 7.88m All supports can be set up variably. The system is delivered complete: ABUS HB rails, trolleys, end plates, cable drag, holder/hanger, chain hoist with control bottle, 4x supports, etc. Crane is dismantled and available immediately Inspection book is available Item location is 75053 Gondelsheim Almost new condition, see pictures There are 10 different systems available, please ask for your size! Dispatch by forwarding agent or pick-up only by appointment

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Hjdpfx Abjmhh Anszjw Scope of delivery: 4 shelf uprights, height 3,000 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 3,000 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm usable depth Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: new, - new -Description:- Saw blade tilt and height adjustment is manual- Max. Cutting height 200mm- Scoring device with separate drive motor- Main saw blade with belt drive and speeds 2800/3665/4800 min¯¹- High dead weight ensures vibration-free running- Large cantilever table with material roller- Rip fence with round bar guide- Extendable aluminum longitudinal fence with two folding stops- 7,5 kW main motor mounted on robust cast iron frame- Quadruple bearing format sliding carriage with double roller carriage made of anodized aluminum with high torsional rigidity- Multiple locking device on sliding table- Standard with table widening and table extension made of sheet steel- Large pendulum protection hood conveniently swivels up with the help of a gas pressure spring- Saw blade clamping via tool-free Rapid systemTechnical data:Dimensions and weightsLength approx. 3386 mmHeight approx. 1330 mmWidth/Depth approx. 3703 mmWeight approx. 1102 kgConnection suctionSuction port diameter 120 mmSuction port diameter saw blade guard 80 mmElectrical dataSupply voltage 400 VInput power 8,3 kWMotor speed 2800 min¯¹Mains frequency 50 HzOutput power 7,5 kWSliding carriage and tableFormat sliding carriage length 3200 mmFormat sliding carriage height 890 mmTable width 685 mmFormat sliding carriage width 416 mmTable length 1255 mmTable height 890 mmNoise emissionSound pressure level 96,5 dB(A)Circular saw unitCutting width with rip fence 1450 mmSaw blade inclination 90 - 45°Max. Cutting height 45°140 mmSpeed of saw blade 2800/3665/4800 min¯¹[Max. Cutting width to the left of the saw blade 3200 mmMax. Cutting height 90° 200 mmDiameter saw blade 550 mmScoring unitDiameter scoring saw blade 120 - 130 mmSpeed scoring saw blade 8000 min¯¹Item no.: 5200550 Hjdpfovxr Rgex Abzsw

Condition: good (used), functionality: fully functional, WE BUY YOUR SHELVES AND ACCESSORIES NATIONWIDE!!! We buy the following products nationwide: *Pallet racks *Industrial shelving *Shelf racks Hsdpfx Abowhwirezow *Cantilever racks *Storage platforms *Drive-in racks *Flow racks *Operational equipment *Conveyor systems We can disassemble the racks upon request.

Condition: like new (used), Year of construction: 2025, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 rack stands, height 2,600 mm with base section 1,000 mm 12 cantilevers with 1,000 mm depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 90 stands in stock) Detailed description: Hodpfxoguk Dve Abzow - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Rack height 2,600 mm - Load capacity per stand 1,800 kg - Base section and cantilevers with 1,000 mm usable depth - Cantilevers in 100 mm increments height adjustable - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is packed sensibly to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 2,600 mm with foot section, 1,000 mm usable depth 12 cantilevers with 1,000 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 2,600 mm - Load capacity per upright 1,800 kg - Foot section and cantilever arms with 1,000 mm usable depth Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Hodpfomhh Dzex Abzsw Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: as good as new (ex-display), Year of construction: 2024, Cantilever rack in painted version (RAL 7016 anthracite): Scope of delivery: 4 shelf uprights height 2.56 m with base section 1.0 m usable depth (1.2 m total depth) 12 cantilever arms with 1.0 m usable depth Longitudinal and diagonal braces for 4 m shelf length (spacing 1.3 m) Fastening material (screws, nuts and washers) (*No paint damage!) Net price on collection: € 1,490.00 plus VAT. Delivery possible for an additional charge Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Surface painted in RAL 7016 (anthracite) - Shelf height 2,560 mm - Load capacity per upright 1,800 kg - Foot section and cantilever arms with 1,000 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) Hedpfxsguk A Hs Abzew - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. The substrate must be made of concrete, be level and suitable for dowels and be able to bear the acting loads. The customer is responsible for checking and ensuring the ground conditions and load-bearing capacity as well as any official approvals required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: as good as new (ex-display), Year of construction: 2024, Cantilever rack in painted version (RAL 7016 anthracite): Scope of delivery: 4 shelf uprights height 4,200 mm with base section 1,200 mm usable depth 12 cantilever arms with 1,200 mm usable depth Longitudinal and diagonal braces for 1,300 mm upright center distance (4,000 mm shelf length) Fastening material (screws, nuts and washers) - (*Delivery or collection in approx. 1 - 2 weeks) - (*No damage to paintwork!) - (*No damaged components!) - (*Replacement parts can be reordered and extended at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Net price: € 1,990.00 plus VAT. Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Surface painted in RAL 7016 (anthracite) - Shelf height 4,200 mm - Load capacity per upright 2,200 kg - Foot section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 740 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. Delivery can be made in approx. 1 - 2 weeks after receipt of order. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The surface must be concrete, level and suitable for dowels and must be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any necessary official approvals are in place. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. Hjdpfomhhypsx Abzew According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.