Used Cantilever for sale (205)

Condition: used, Cantilever racking, heavy duty racking consisting of: -Shelf: with 2 stands each -Support arms: double-sided -6x ledger depths: 900/500/400/300/230 mm -welded -Also: other quantities and heights available on request -Number: 1x shelves available Pgsdpfxjd Eqlpe Ag Toi -Transport dimensions: 2100/2020/H2170 mm -Own weight: 430 kg/piece

Condition: new, 1860 m³/h Pressung 2.900 Pa 1,1 kW filter surface area 10 m² 72 dB(A) 400/50 V/Hz 665 x 1100 x 1495 mm 200 kg - Hose arm 3 m, joints inside - Filter cartridge: dust class M - Pre-filter: baffle plate - Current type: 3Ph+N+PE Pgodpfx Agohp S Tre Toi The filter system ----- The mobile filter system of the Cartmaster IFA type is thanks to the automatic Cleaning particularly suitable for welding work with unalloyed and alloyed steels, galvanized material and aluminum with heavy smoke development. It corresponds to the safety requirements for devices Welding fume class "W3" (high-alloy steels with alloy components > 30% Nickel-based alloy).If used as intended, the system can be used for the Recirculation mode used because the requirements for the Exceptions according to TRGS 560 are fulfilled. That special developed, dirt-dependent cleaning system ensures a good cleaning behavior of the filter cartridge, so that an optimal suction performance is guaranteed throughout the operation. The cleaned particles fall into a dust collection drawer from which they can then be disposed of. The powerful spiral fan ensures even with saturated Filter cartridges for a high volume flow. The filter media ----- A baffle serves as a pre-separator for coarse particles. The filter cartridge installed below (dust class M, degree of separation > 99%) filters the finest smoke and dust particles. The cartridge is factory coated which increases the service life. The extraction arm ----- The extraction arm can be moved with the 3 internal joints Position spring support slightly and is in the set position cantilevered. A throttle flap integrated in the extraction hood enables the Flow rate setting.

Condition: new, 1860 m³/h Pressung 2.900 Pa 1,1 kW filter surface area 10 m² 72 dB(A) 400/50 V/Hz 665 x 820 x 1365 mm 165 kg mobile extraction, welding fume extraction (manual cleaning by loss of pressure) - Hose arm 3 m, joints inside - Filter cartridge: dust class M - Particle pre-separator: baffle plate - Current type: 3Ph+N+PE The filter system ----- The mobile filter system of the type StrongMaster IFA is particularly suitable for Welding work with unalloyed and alloyed steels, galvanized material and Aluminum in case of heavy smoke development. She corresponds to the Safety requirements for devices in the welding fume class "W3" (high-alloy steels with alloy components > 30% nickel-based alloy). When used as intended, the system can be used for be used in the recirculation mode, since the requirements for the Exceptions according to TRGS 560 are fulfilled. The filter will via a maintenance door using a compressed air gun from the clean air side cleaned. The cleaned particles fall into a dust collection drawer from the Podpfxskm Ryne Ag Tsgi they can then be disposed of. The powerful scroll fan ensures a high volume flow even with saturated filter cartridges. The filter media ----- A baffle serves as a pre-separator for coarse particles. The filter cartridge installed below (dust class M, degree of separation > 99%) filters the finest smoke and dust particles. The cartridge is factory coated which increases the service life. The extraction arm ----- The extraction arm can be moved with the 3 internal joints Position spring support slightly and is in the set position cantilevered. A throttle flap integrated in the extraction hood enables the Flow rate setting.

Condition: reconditioned (used), functionality: fully functional, turning diameter over cross slide: 690 mm, spindle bore: 150 mm, turning diameter: 1,040 mm, turning diameter over top slide: 690 mm, center height: 500 mm, center width: 2,000 mm, spindle speed (max.): 5,000 rpm, travel distance X-axis: 160 mm, travel distance Z-axis: 380 mm, bar passage: 55 mm, Center height: 500 mm Distance between centers: 2.000 mm Maximum turning diameter: Over cross slide: 690 mm Over bed: 1.040 mm Pgedpfx Aoyhhuwsg Tei Over gap: 1.070 mm Bed width (hardened guides): 670 mm Gap length: 480 mm Gap length in front of the faceplate: 320 mm CARRIAGE Length of bed guideways: 1.020 mm Cross slide travel: 640 mm Compound slide travel: 360 mm SPINDLE Spindle nose: ASA 15’’ Spindle bore diameter: 150 mm Front bearing size (NN): 200 / 310 / 82 mm Rear bearing size (NNU): 190 / 260 / 69 mm Internal Morse taper reduction sleeve: No. 6 Number of spindle speeds: 24 Speed range: 4 ÷ 800 rpm THREADING Total number of threads: 398 Metric threads: 0.5 ÷ 224 mm Module threads: mod. 0.25 ÷ 11 Whitworth threads: 56 ÷ 1/8 TPI Diametral pitch threads: 112 ÷ 1/4 DP FEEDS Number of feeds: 108 Longitudinal, cross and compound feeds: 0.05 ÷ 22.4 mm/rev RAPID TRAVERSES Longitudinal, cross and compound: 2.500 mm/min Longitudinal return: 5.000 mm/min TAILSTOCK Quill diameter: 130 mm Quill Morse taper: No. 6 Quill travel: 420 mm STEADY RESTS Bed steady rest capacity: 140 ÷ 500 mm Carriage steady rest capacity: 40 ÷ 350 mm PERMISSIBLE LOAD Cantilever load: approx. 1.500 kg Between centers, without steady rest: approx. 5.000 kg Between centers, with steady rest: approx. 6.000 kg Machine weight: approx. 7.800 kg

Condition: like new (used), Year of construction: 2025, Cantilever racking with roof supports: Hot-dip galvanized bolt-together system Scope of delivery: 9 rack uprights, height 4,230 mm, with base plate, usable depth 1,200 mm 27 cantilever arms, usable depth 1,200 mm, with deflectors 9 roof supports with 1,500 mm cantilever, pre-drilled for on-site roof construction (*Without wood purlins and trapezoidal sheets for roof assembly) Including longitudinal and diagonal braces for 1,500 mm upright spacing Incl. fastening material (without floor anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) Pgedpfx Aoh R Taqjg Toi - (*Spare parts reordering and extensions possible at any time) - (*Offer available in larger quantities: approx. 50 uprights in stock) Detailed description: - Robust steel construction made from IPE sections - All components with hot-dip galvanized finish - Load capacity per upright 2,700 kg plus roof, wind, and snow loads (Maximum snow load 1.85 kN/m² and wind load zone 2) - Load capacity per cantilever arm 900 kg - Including roof supports (Maximum snow load 1.85 kN/m² and wind load zone 2) - Cantilever arms height-adjustable in 100 mm increments - 3 bolt-on cantilever arms per upright, depth 1,200 mm with deflector = 4 storage levels vertically - Including longitudinal and diagonal bracing with 1,500 mm upright spacing - Rack length: 12,100 mm - Including fastening material (without floor anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Professional telephone consultation - Made in Germany - Short delivery times - On-site pickup possible Our cantilever racks are exclusively produced in Germany. We offer reliable transport with prior notification before delivery. The goods are packaged for easy unloading. The installation surface must be concrete, level, suitable for anchoring, and capable of supporting the applied loads. The floor condition, load-bearing capacity, and any required official permits must be checked and ensured by the customer. The uprights must be anchored to the floor on site; wall anchoring is not required and not recommended. According to occupational safety regulations, it is recommended that the uprights have at least a 500 mm overhang above the top storage level.

Condition: like new (used), Year of construction: 2025, Cantilever rack with roof supports: Hot-dip galvanized bolted system Scope of delivery: - 9 rack uprights, height 4,230 mm with base section, usable depth 1,200 mm - 27 cantilever arms, 1,200 mm usable depth, with guards - 9 roof supports with 1,500 mm cantilever, pre-drilled for on-site roof construction (*Excluding timber purlins and trapezoidal metal sheets for the roof structure) - Includes longitudinal and diagonal braces for 1,500 mm upright spacing - Incl. mounting hardware (excluding floor anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Spare parts and extensions available to order at any time) - (*Offer available in larger quantities: approx. 50 uprights in stock) Detailed description: - Robust steel construction made from IPE profiles - All components hot-dip galvanized - Load capacity per upright: 2,700 kg plus additional roof, wind, and snow load (Maximum snow load 1.85 kN/m² and wind load zone 2) - Load capacity per cantilever arm: 900 kg - Including roof supports (Maximum snow load 1.85 kN/m² and wind load zone 2) - Cantilever arms height adjustable in 100 mm increments - Per upright: 3 bolted cantilever arms, depth 1,200 mm, with guards = 4 storage levels - Including longitudinal and diagonal braces with 1,500 mm upright spacing Psdpfx Agjmhhy Nj Tsgi - Rack length: 12,100 mm - Including mounting hardware (without floor anchors) - With assembly instructions and C4 load labels according to DIN standard - Specialist telephone consultation - Made in Germany - Short delivery times - On-site pickup possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight services with advance notice before delivery. The material is thoughtfully packaged to facilitate easy unloading. The substructure must be concrete, level, and suitable for dowel anchoring, and capable of bearing the applied loads. The floor condition and load-bearing capacity, as well as any required official permits, must be checked and ensured by the customer. The rack uprights must be anchored to the floor on site. Anchoring to the wall is neither required nor recommended. According to Occupational Safety regulations, it is recommended that the uprights have at least 500 mm overhang above the top storage level.

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: 2022KL2938, total width: 2,400 mm, total length: 3,400 mm, total height: 910 mm, overall weight: 900 kg, warranty duration: 12 months, • Glass cutting table SDRD FULL Tilted table which supports the process of manual cutting the glass, product designed and manufactured in Poland Length - 3400 mm Pgjdpfxsh Nx R Ts Ag Tei Width - 2400 mm Height - 910 mm Breaking bar - 2 pieces in cross arrangement Bars steering - by foot pedals Air cushion system - installed Power of fans (air cushion) - 2,2 kW Air cushion system steering - by foot pedals and hand button Tilting of the top - pneumatical Stabilization of tilting - by hydraulic speed controller Support of quick tilting - by to gas springs Pull-out cantilevers of glass loading - yes, manually Covering of the top - grey felt Covering of the circumference - ash slats Wheels - 4 rotary, with increased load Levelling feet - 4 pieces installed Steel construction covering - polyurethane covering Filling of the lower beam in stationary construction - vibrated, fibre reinforced concrete Table available from stock. Our company also delivers worldwide.

Year of construction: 2022, condition: new, Altendorf WA 6 manual height adjustment, double roller carriage length 2000 mm scoring unit, swiveling, cantilever table, angular miter fence, automatic brake, lowerable below table height ----- Technical data ----- Swivel range: 0 - 45 °, cutting width at rip fence: 1.000 mm, max. cutting height: 87 mm, max. saw blade Ø: 315 mm, Swivel range miter fence: up to 49 °, Speeds: 4,200 rpm, Engine power main motor: 5.5 hp / 4 kW, motor power scoring motor: 0,5 hp / 0,37 kW, Working table height: 910 mm, suction nozzle Ø: 1 x 100 / 50 mm each, weight: 450 kg Pgsdoihahmjpfx Ag Tji Large suction hood Location: Ex stock 54634 Bitburg - immediately available - Location: Ex stock 54634 Bitburg - free on truck - - immediately available -

Condition: new, Year of construction: 2025, Woodworking machinesTable routers Minimax twf55 es Item number: 5502261 Sturdy cast steel construction Anodized aluminum sliding carriage Large dimensioned milling unit made of grey cast iron, swivels up to -45° to the rear Four milling speeds from 3500 to 10000 min¯¹ Right-left rotation as standard Height and inclination display accurate to 1/10 mm Fast and easy speed change via eccentric clamping Solid and precise cast iron table, stress relieved and re-annealed for lasting precision Powerful 5.0 kW industrial motor Curved milling hood included in delivery Made in Italy Dimensions and weights Length (product) approx. 1200mm width/depth (product) approx. 2000mm Weight (net) approx. 510kg Connection suction suction connection diameter 2 x 120mm Work table working table length 1200mm working table width 530mm table height 900mm sliding carriage length 1200mm Slide width 360mm Slide height 142mm Installation information Required space length 2800mm Space requirement width/depth 2910mm Explanation of space requirements The dimensions take into account maximum travels or useful lengths. Machine body length 1200mm Machine body width/depth 846mm Working area length 1600mm Working area width/depth 2300mm Explanation of working area Please add the dimensions given with the space requirement to obtain the free installation area recommended for the machine. Electrical data Supply voltage 400V Mains frequency 50Hz Power drive motor 5,0kW Milling spindle spindle inclination 0 to -45 useful length of the spindle 125mm Spindeldrehzahl(en) 3500/6000/8000/10000min¯¹ Milling spindle speed indicator LED on the front of the machine spindle arbor diameter 30mm Milling tool diameter max. Tool diameter max. 240mm tool diameter max. lowerable 230mm tool diameter max. profile milling 240mm Pgodpfx Aei Dphtsg Tsi Tool diameter max. tenon milling 320mm EQUIPMENT Equipment Aluminum sliding carriage ✔ Milling fence Heavy-duty professional version with hold-down device, protective cover and aluminum milling fence jaws Telescopic miter fence with two folding stops Cantilever table ✔ Curved milling protective hood ✔ Eccentric clamp ✔ Handle on sliding carriage ✔ Height adjustment of the spindle manually Tilt adjustment of the spindle manual Control manual height and tilt adjustment of the milling unit Position of the control elements on the machine body location: ex stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2025, Table milling machine minimax twf 55 es M 3 UP Professional workman's machine with motorized height and inclination adjustment of the milling spindle, four speeds and electronic control system Item number 5502266 Brand Holzkraft / SCM EQUIPMENT Equipment Aluminum sliding carriage ✔ Handle at sliding carriage ✔ FLEX ONE routing fence: heavy-duty professional design, automatic adjustment of the entire routing fence depending on the tool diameter, manual adjustment of chip removal, swing-away device, aluminum fence jaws with connecting strips Height adjustment of the spindle motorized. Telescopic miter fence with two folding stops Inclination adjustment of the spindle motorized Cantilever table ✔ Ready 3 control: Programmed movement of the milling unit in two axes, Automatic adjustment of the entire milling stop depending on the tool diameter, Stepless adjustment via switch or automatic positioning system Curved milling protective hood ✔ Position of control elements Control panel at eye level, swiveling Eccentric clamp TECHNICAL DATA Dimensions and weights Pedpfx Aehp Rc Isg Tjgi Length (product) approx. 1200mm Weight (net) approx. 510kg width/depth (product) approx. 2000mm Connection suction suction connection diameter 2 x 120mm Work table Working table length 1200mm Sliding carriage length 1200mm Working table width 530mm Sliding carriage width 360mm Table height 900mm Slide height 142mm Installation information Space requirement length 2800mm Machine body width/depth 846mm Space requirement width [...]

Condition: excellent (used), functionality: fully functional, For sale is an extensive, complete scaffolding lot suitable for professional building construction and façade work. System Façade Scaffolding Working Scaffold Reinforcement Scaffold Eaves-Side Scaffold Ideal for scaffolding companies, construction businesses, or for expanding existing scaffolding inventories. The material is systematically listed and registered. Numerous additional components are included. System: SL 70 / SL 100 Total area: approx. 8,000 m² scaffold surface Total weight: approx. 105,000 kg Main components included (excerpt): Frames & Supports: SL 70 Vertical Frames: 200 × 70 / 150 × 70 / 100 × 70 / 50 × 70 SL 100 Vertical Frames: 200 × 100 / 100 × 100 Decks & Platforms: Wooden Decks: 300 × 32 / 250 × 32 / 200 × 32 / 150 × 32 / 100 × 32 / 70 × 32 Steel Decks: 300 × 32 / 150 × 32 Guardrails & Safety: Rear Guardrails: 300 / 250 / 150 Double-Sided Guardrails SL 70 / SL 100 Side Guardrail Frames SL 70 / SL 100 Guardrail Post Supports / Guardrail Posts Top Deck Safety Barriers Diagonals & Bracing: Diagonals 300 × 200 Diagonals 250 × 200 Accessories & Special Parts: Toe Boards: 300 / 250 / 150 Adjustable Base Plates: 30 / 50 / 60 / 80 Spacers / Distance Tubes Roof Edge Protection SL 70 / SL 100 Weather Protection Roof ALU Access Hatch Decks with Ladder Cantilever Beams: 32 / 64 / 74 Alu-Staircase + Guardrail 2.50 m 610 Steel Lattice Beams Couplers (Swivel / Right-Angle Coupler) A detailed parts list is fully available (see photo). Further accessories available. Condition: Used, fully functional System-compatible scaffolding material Podpfxoycfyys Ag Togi Suitable for professional construction site use Location: On request Inspection: By appointment Loading & transport can be organized Sale preferred as a complete lot or in large batches

Year of construction: 2009, condition: used, Apple 15 head depositor Model: CCP12 Pgedpfxsb Ucwko Ag Tji Stainless cantilever framed 15 head machine

Condition: used, functionality: fully functional, Conical mixer steel gross 5000 litres net 3500 litres (70%) Pgodpfx Aoydu Uveg Tsi 2 outlets: 1x bottom outlet with original ball segment, 1x side outlet with slide gate valve (position for lump breaker) cantilevered mixing screw operates well (dismantled after factory shutdown) including base frame

Condition: like new (used), Year of construction: 2020, operating hours: 4 h, Jungheinrich pedestrian stacker COMPACT AND MANEUVERABLE As a cantilever pedestrian stacker, the Jungheinrich EJG is always used where no wheel-arm supported trucks can be used, where no wheel-arm supported forklift trucks can be used (e.g. for picking up pallets crosswise, special loading aids, use of racks with impact protection). With an overall width of only 910 mm and high maneuverability, the truck can also be used in narrow storage areas. Manufacturer: Jungheinrich Type: EJG 112 Year of construction: 2020 Drive type: Electric Load capacity: 1,200 kg Lifting height: 2.500 Load center of gravity: 500 mm Dead weight: 2,175 kg Basic dimensions: Overall height: 1,880 mm Fork length: 1,150 mm Performance data: Motor:24 V electric Engine power:1.6 kW Battery:24 / 375 V/Ah Charger:24 V Power transmission: Pulse control Steering: Drawbar steering Year of construction 2020 Type: EJG 112 Condition: used / second-hand Podpfjnp Hzksx Ag Tegi Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) We will be happy to answer any further questions you may have on the phone.

Condition: used, Cut-to-length line Pro-Eco with Cassette Type Precision Leveler 60 x .187 x 50,000Lbs (A3789) Maker: Pro-Eco Excellent conditions SPECIFICATIONS: MAX WIDTH 60" MAX THICKNESS 187" MANUFACTURER - PRO-ECO YEAR - 1985, REINSTALLED 2002 WIDTH RANGE - 8" to 60" GAUGE RANGE - .024" to .187" WEIGHT CAPACITY - 50,000# (25 TON) COIL OD - 36" to 72" COIL ID - 19" to 24" SHEET LENGTH - 24" to 168" SHEET WIDTH - 8" to 62" PACK HEIGHT - 30" (INCLUDING DUNNAGE) PACK WEIGHT - 20,000# LINE DIRECTION - RIGHT to LEFT LINE SPEED - 50 to 300 FPM (VARIABLE) LEVELER TYPE - MECHANICAL WEDGE STYLE w/ TWO CASSETTES LINE COMPONENTS: FOUR ARM ENTRY STORAGE TURNSTILE FLOOR LEVEL COIL LOADING CAR CANTILEVERED MANDREL UNCOILER w/ WATER COOLED BRAKE PIVOTING AND TELESCOPING PEELER BLADE ENTRY PINCH ROLLS ROLLER TYPE SIDE GUIDES ENTRY CROP SHEAR SIDE TRIMMER HYDRAULIC SERVO DRIVE (CURRENTLY NOT OPERATIONAL) MECHANICAL STYLE LEVELER FRAME W/ 200 HP MOTOR CASSETTE #1 - 19 ROLL, 2.50" DIAMETER, 5 HI, 7 BACKUP FLIGHTS Pgedjthg Dispfx Ag Tsi CASSETTE #2 - 19 ROLL, 1.75" DIAMETER, 5 HI, 7 BACKUP FLIGHTS STRIP INSPECTION AND CARRY-OVER TABLE w/ NON-MARKING ROLLS LOOPING PIT QUADRANT TABLES w/ NON-MARKING ROLLS ROLLER TYPE STRIP SQUARING TABLE PRECISION ROLL FEEDER W/ 55 HP MOTOR HIGH SPEED MECHANICAL CUT OFF SHEAR W/ 40 HP MOTOR BLANK INSPECTION CONVEYOR w/ NON-MARKING BELT REJECT BELT CONVEYOR w/ NON-MARKING BELT AND SCRAP CART 14 FOOT AIR FLOAT STACKER w/ SQUARING GUIDES AND END STOP 14 FOOT STACKER LIFT CONVEYOR w/ END DISCHARGE ROLLERS 14 FOOT STACKER RUNOUT CONVEYOR w/ END DISCHARGE ROLLERS OPERATOR CONTROL STATIONS UPDATED AC CONTROLS w/ ALLEN BRADLEY "CONTROL LOGIX" PLC (2006) UPDATED DRIVE CONTROLS w/ SIEMENS "SIMOREG" CONTROLLERS (2006) CLOSED LOOP HYDRAULIC SYSTEM CLOSED LOOP WATER COOLING SYSTEM

Year of construction: 2012, condition: good (used), machine/vehicle number: ENOG, DEMAG KBK crane headliner crane runway dimensions approx. 8x4m Payload / lifting load 250 KG - 0.25to Technical data of the system: Crane runway made from Demag KBK1+2 rails The system is delivered complete: KBK rails, rail connectors, trolleys, end plates, cable carriers, holders/hangers, etc. incl. Demag DC-COM 250KG chain hoist Crane is dismantled and available immediately Used condition, see pictures Item location is 75053 Gondelsheim Dispatch by forwarding agent or pick-up only by appointment Demag KBK1 KBK2 and KBK3 rails are stock items! Other KBK systems are also available. Payload 125KG - 1600KG Pgsdpfx Ajmqf Nfog Tsi Please inquire about your crane runway with cantilever load and dimensions.

Condition: good (used), Year of construction: 2017, In this offer you buy used office furniture, which is in good condition. They were delivered in 2017 and are generally in very good condition, since little used. Items for sale: We also offer workplace sets for 450€. 1x desk - Manufacturer: FM - 160 x 80 x 76 (stepless height adjustable 68cm to 76cm) - gray top - aluminum frame 1x office chair "Dauphin MagicShape elan - armrests - completely adjustable - cover polo grey/black 1x mobile pedestal - Manufacturer: FM - 43,4 x 80 x 59 - one material drawer - 3 steel drawers with softclose - lockable incl. key Desks: - Approx. 10x desk from the manufacturer FM 1600 x 800 x 680 to 760 (infinitely height adjustable) in the color light gray. Frame made of aluminum - Approx. 12x folding table (can be used as a desk) 1600 x 800 x 720 on castors, in the color light gray. Aluminium frame - Approx. 2x round meeting table 1000mm diameter in the color light gray. Aluminium frame - Approx. 4x high table 1600 x 800 x 1300 in the color arctic white. Frame in white aluminum Chairs: - Approx. 10x Dauphin swivel chair MagicShapeS elan with armrests and fully adjustable. Fabric cover Polo black, base plastic black - Approx. 44x Interstuhl Hero 550H cantilever chair with armrests. Upholstery in ruby red color. Metal frame chrome-plated. - Approx. 52x Interstuhl Hero 550H cantilever chair with armrests. Upholstery in the color ocean blue. Metal frame chrome-plated. - Approx. 10x Interstuhl Kinecticis5 710K bar stool with footrest. Upholstery in the color black. Frame in silver color. - Approx. 16x Interstuhl Kinecticis5 710K bar stool with footrest. Upholstery in the color ocean blue. Frame in silver color - 12x Interstuhl Kinecticis5 710K bar stool with footrest. Upholstery in the color red. Frame in the color silver - 16x Interstuhl Kinecticis5 710K bar stool with footrest. Upholstery in the color ruby red. Frame in the color silver Storage space: - Approx. 16x FM 434 x 800 x 590 mobile pedestal with one material drawer and 3 steel drawers. Body completely in the color light gray. Handles made of aluminum meeting table with 4 conference chairs - 750,-€ net high table with 6 bar stools - 1500,-€ net Podpoiiv Ikofx Ag Tegi Prices may vary slightly depending on the quantity purchased. We will be happy to prepare a suitable offer for you. You can also purchase each piece of furniture separately. Condition: This offer is used furniture, which may show signs of use (minor scratches or yellowing). Packing and shipping: You are welcome to look at everything during our business hours. Please make an appointment for this! Seaworthy packing and worldwide shipping is possible on request! For more information you can of course also contact us personally.

Condition: new, Year of construction: 2025, functionality: fully functional, Ticab Printing System TPS is an innovative cantilever equipment. It allows feeding huge items beneath the print head. The print head can be adjusted up to 30 cm above the conveyor belt to feed folded cardboard boxes or other huge items. High quality Hewlett Packard HP pigment ink provides resistance to the fading, scratches and water after the image dries. Call us to get a beneficial commercial offer. Specifications:  Print area width: up to 29.7cm (11.7 in) Pgodpou Ibhwefx Ag Tsi  Print area length: from 2.54 cm (1 inch) to 91.44 cm (36 inch)  Workpiece movement speed: up to 45.72 cm (18 in) per second  Printing speed: up to 50--70 copies\min A4, up to 16 copies\min A3  Print resolution: 1200x1200dpi  Number of inkjet nozzles: 59136 (14 printing zones of 4224 nozzles each)  Colors: CMYK (Cyan, Magenta, Yellow, Black)  Ink type: water-based pigment ink  Information connection: Ethernet 10/100/1000 Base-T network port  Operating system: Windows (recommended Windows10)  Hewlett Packard HP driver  Trusted by professionals in 55 countries worldwide!

Condition: new, Pole pallet, manurack, mobilrack - new Mobile storage racks are used for storing goods of unusual dimensions and have a double purpose. They can be used as transport pallets and with the installation of 4 support tubes, they can be used to build storage racks which can be transported without having to reload the goods placed on them. Both heavy and light products can be stored on a metal pallet. Thanks to its simplicity and speed of assembly, Mobilrack can increase storage capacity in a few moments. At the end of the season, the pallet can be dismantled to save space in the warehouse. This offer applies to a single pallet/base: Commodity code: MTP000276 Psdou Trpyjpfx Ag Tjgi Length: 154.5 cm Width: 118 cm Bax3Ttyxrfw Height : 31 cm Load capacity : 1500 kg Finish: hot-dip galvanised Price : 82 euros / piece The offer concerns a double pallet /base/ : Commodity code : MTP000283 Length : 202.5 cm Width: 118 cm Height : 31 cm Load capacity : 2000 kg Finish: hot-dip galvanised Price : €120 / piece Each pallet of posts requires 4 cantilever tubes, available in different sizes according to the customer's needs: 120, 150, 200cm. The offer concerns a tube for a Manurack 120×6 cm rack: Product code : MPP000706 Height (cm): 120 Thickness (mm): 2,9 Diameter (cm): 6 Price : 7 euro / piece The offer concerns a tube for a Manurack 150×6 cm rack: Item code : MPP000704 Height (cm): 150 Thickness (mm): 2.9 Diameter (cm): 6 Price : 8,50 euro / piece The offer concerns a tube for a Manurack 200×6 cm rack: Item code : MPP000705 Height (cm): 200 Thickness (mm): 2.9 Diameter (cm): 6 Price : 11,50 euro / piece Prices quoted are for wholesale quantities ( full truckload ) for export outside Poland, please contact us for details. To check wholesale and retail prices within Poland, please contact us. * I have large quantities ... * Transport throughout Europe possible. * The above offer does not include transport costs. * Location: Chmielów/Tarnobrzeg, Poland.

Condition: new, Year of construction: 2025, Laser source: Raycus or Max: 4/6/8/12 kW Laser head: 3 D BOCI , Control system: FSCUT 5000 A Chuck: 20-450 mm Loading/unloading: 12000 mm X/Y axes Positioning accuracy: ±0.05/1000mm Repeat accuracy: ±0.03/1000mm Acceleration: 0.8g (m/s²) Rotation speed: 60 rpm Max. Positioning speed: 60 m/min Max. Max. weight of a tube: 1500kg 1.Raycus 6000W laser source 2.BEVEL laser head 3.welded frame DPL 4.Schneider electrical components 5.helical rack KH 6.techmech reducer 7.Yaskawa servomotor 8.SHAC guides 9.integrated power control Pgjdpfxsi Apfzo Ag Tsi 10.FScut 5000 software 11.integrated electrical cabinet 12.HANLI water chiller 13.cantilever gantry axis-X FHBS 14.automatic waste collection 15.crawler-type automatic workpiece collection 16.automatic support system 17.loading frame 12000mm 18.unloading frame 12000mm

Condition: like new (used), Year of construction: 2025, Used cantilever racking: Screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights Height 4,160 mm with base section 1,200 mm usable depth 12 cantilever arms with 1,200 mm usable depth, standard Longitudinal and diagonal braces for 4,000 mm shelf length (spacing 1,300 mm) Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Replacement parts can be reordered and extended at any time) Pgodpfx Aofdkb Tsg Tei - (*Offer available in larger quantities: approx. 90 stands in stock) Detailed description: - Sturdy steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 4,160 mm - Load capacity per upright 2,250 kg - Base section and cantilever arms with 1,200 mm usable depth - Cantilever arms height-adjustable in 100 mm increments - 3 screw-on cantilever arms per upright, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal bracing for 1,300 mm spacing - Shelf length = 4,000 mm - Including fixing material (without floor anchors) - With assembly instructions and load plates C4 according to DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with notification prior to delivery. The material is sensibly packed to enable easy unloading. For outdoor installation, the load-bearing capacity is reduced by the wind and snow load. The base must be concrete, level and suitable for dowels and be able to bear the loads. The customer must check and ensure that the ground conditions and load-bearing capacity as well as any official approvals that may be required. The shelf stands must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the employers' liability insurance association, it is recommended that the uprights on the uppermost storage level protrude at least 500 mm from the top edge of the uprights.

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 3,500 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 3,500 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm usable depth Pgjdomhh Dhopfx Ag Tsi Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 2,600 mm with foot section, 1,000 mm usable depth 12 cantilevers with 1,000 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 2,600 mm - Load capacity per upright 1,800 kg - Foot section and cantilever arms with 1,000 mm usable depth Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 600 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. Pedpfx Aomhh Dzsg Tsgi The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2025, Cantilever rack used: screw system in hot-dip galvanized design Scope of delivery: 4 shelf uprights, height 3,000 mm with foot section, 1,200 mm usable depth 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm spacing Fastening material (screws, nuts and washers) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 40 uprights in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Shelf height 3,000 mm - Load capacity per upright 2,250 kg - Foot section and cantilever arms with 1,200 mm usable depth Cantilever arms in Height adjustable in 100 mm increments - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and C4 load plates in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - On-site collection possible Our cantilever racks are manufactured exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. Pgedpfxomhh Ans Ag Tji The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: like new (used), Year of construction: 2024, Used cantilever rack: screw system in hot-dip galvanized design Scope of delivery: 4 rack stands, height 3,000 mm with base section 1,200 mm 12 cantilevers with 1,200 mm usable depth, standard Including longitudinal and diagonal braces for 1,300 mm axle spacing Incl. fastening material (without ground anchors) - (*Delivery time approx. 1 week) - (*No damaged parts!) - (*Reorder spare parts and extension possible at any time) - (*Offer available in larger quantities: approx. 50 stands in stock) Detailed description: - Stable steel construction made of IPE profiles (screw system) - Hot-dip galvanized surface - Rack height 3,000 mm - Load capacity per stand 2,250 kg - Base section and cantilevers with 1,200 mm usable depth - Cantilevers in 100 mm increments height adjustable - 3 screwable cantilever arms per stand, standard (= 4 storage levels) - Load capacity per cantilever arm 750 kg - Including longitudinal and diagonal braces for 1,300 mm spacing - Shelf length = 4,000 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Expert advice by telephone - Made in Germany - Short delivery time - Collection on site possible Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. Psdpfx Ageguk Dke Togi The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.