Used Cnc Rotary Transfer Machine for sale (67,049)

Condition: good (used), Year of construction: 2018, functionality: fully functional, machine/vehicle number: HVIE2913, travel distance X-axis: 660 mm, travel distance Y-axis: 406 mm, travel distance Z-axis: 508 mm, feed rate X-axis: 24 m/min, feed rate Y-axis: 24 m/min, feed rate Z-axis: 24 m/min, nominal power (apparent): 9 kVA, controller manufacturer: HURCO, controller model: WINMAX, total height: 2,600 mm, total length: 2,500 mm, total width: 2,000 mm, table width: 406 mm, table length: 762 mm, table load: 682 kg, overall weight: 3,000 kg, spindle speed (max.): 12,000 rpm, operating hours of spindle: 6,486 h, number of slots in tool magazine: 20, mount diameter: 40 mm, tool length: 250 mm, tool diameter: 89 mm, tool weight: 7 g, input voltage: 400 V, input frequency: 50 Hz, input current: 21 A, HURCO VM 10 i CNC Vertical Machining Center Bedpfx Ajy Iwm Djk Hswl - Serial number: S10-162268FKBCH - Distance spindle nose to table: 102 - 610 mm - T-slots in table: 3 - T-slot width: 18 mm - Slot spacing: 100 mm - Tool holder: SK 40 - Tool diameter at full capacity: 89 mm - Max. total weight in turret: 86 kg - Position measuring systems: photoelectric, standard rotary type, mounted on motor side, measuring method via light - Control resolution: 0.002 mm - Positional accuracy over travel: 0.010 mm - Repeatability over travel: 0.005 mm - incl. RENISHAW 3-D probe - Note: The vices visible in the photos are not included! Note: The item must be collected on a fixed date, to be agreed, between 23.06. and 25.06.2026. FCA D-73230 Kirchheim Teck – loaded onto truck

Condition: good (used), Year of construction: 2002, functionality: fully functional, grinding diameter 20-35mm X-travel 450mm, Z-travel 200mm exhaustion device, extinguishing system Bjdpfx Akoy Ix Ezj Hswl weight ca. 4000kg

Condition: ready for operation (used), Year of construction: 2003, functionality: fully functional, 3D Coordinate Measuring Machine | Brand: MAUSER/ZEISS | Type: KMZ-G 602520 | Year of manufacture: 1988/2003 Optionally available with an air-conditioned hall. The machine has been calibrated regularly by ZEISS. The last calibration was performed on August 7, 2025, Bwodsy Iub Sjpfx Ak Hel the next calibration (recommended) is scheduled for August 2026. TECHNICAL SPECIFICATIONS:: Measuring ranges (Length x Width x Height): 6.000 x 2.500 x 2.000 mm Travels: - X-axis: 6.000 mm - Y-axis: 2.500 mm - Z-axis: 2.000 mm - Length measurement uncertainty according to VDI/VDE 2617: U3 = (5,0 + L/250)µm, V2 = 3,5 µm - Length measurement uncertainty according to ISO 10360-2: MPE_E = (5,0 + L/250)µm - Environmental conditions for maintaining the specified accuracy: * Temperature range: 21°C +/- 3°K * Temperature fluctuation: 0,5°K/h, 1,0°K/d, 0,5°K/m - Environmental conditions for operation: * Temperature range: + 15°C up to 35°C * Humidity: 30 up to 70% General features, Equipment: - Portal measuring machine with ultra-precision guides and ball-screw drives - Second Y-axis with granite guideway and air bearing - High-resolution Zeiss scales - Positive-drive mechanisms in all three axes - Collision protection for the quill and probe head (for VAST-TK) for manual and setup modes - Safety position for crane interlock - Reference temperature compensation - Microcomputer control - Practice piece: cube, star-shaped stylus - Reference probe D = 8 mm, length: 115 mm - Reference standard D = 30 mm - includes basic software package - Load-bearing capacity: Limited only by the foundation design - Measuring system: VAST - Software: Zeiss CALYPSO - Documentation Without guarantee of completeness and correctness of the technical information and the equipment. - Subject to prior sale -

Condition: good (used), Year of construction: 1986, CNC universal milling machine Bwjdpsy H Ifbofx Ak Hol Make DECKEL Type: FP5NC Bj.1986 control DIALOG 4 Traverse paths: X710mm Y600mm Z500mm Clamping table : 1000mm x 550mm Tool clamp: SK40 Feed speed programmable: 2 ... 3600 mm / min Speed: 18 ... 6300 rpm Spindle power: 7.5KW machine in stock.

Condition: good (used), Year of construction: 1990, HEIDENHAIN TNC-355 Bodpjfg Ep Dofx Ak Howl Working travels 850x500x450mm Table size 1250x500mm Spindle taper 50 Spindle speeds 35,5-1800 rpm Misc.accessories MARCELS MASCHINEN CH

Condition: used, Year of construction: 2011, AXES Bwsdpfsyymz Uox Ak Hel Working Range X-Y-Z Axes * mm 3050-1300-180 Workpiece length for pendulum operation mm 1390 Stroke X-Y-Z Axes mm 3460-1735-250 Max. traverse speed of X-Y axes m/min 60 WORK TABLE Number of workpiece supports and vacuum cups 6 / 2 standard type Standard end stops / position 1 / rear Vacuum pump m3/h 90/108 DRILLING UNIT Vertical spindles std/quantity/speed 1/min 12 (8X-5Y) / 4000 Horizontal spindles std/quantity/speed 1/min 6 (4X-2Y) / 4000 Integrated grooving / saw unit in X Ømm/1/min 120 / 6000 Motor power kW (HP) 2.2(3) ELECTROSPINDLE Motor power std./opt. (S6) kW (HP) 7.5(10) / 11(15) Max. speed 1/min 24000 Tool changer traveling with unit carrier in X 4 places, pneumatic INSTALLATION Installed power KVA 23÷28.5 Compressed air requirement Nl/min 450 Extraction air requirement m3/h 1900+1900 (3400) Required extraction air velocity m/sec 30 Extraction connection diameter mm 150+150 (200) Machine weight Kg 3000 * X: distance between stops; Y: milling center as reference point; Z: workpiece passage GENERAL FEATURES CNC-controlled drilling and milling center, C-frame design, and worktable with adjustable workpiece supports and vacuum suction cups, for: - Vertical drilling on the panel surface - Horizontal drilling on all four workpiece sides - Groove milling with disc cutter in the “X” direction - General milling work Self-supporting structure and work table Structure made from welded steel construction with control cabinet integrated into the machine frame. Available in two different lengths and with standard workpiece supports or TV carrier options. Box construction made from cold-rolled steel with internal stiffening ribs and protective devices comprising a drilling head with vertical spindles, horizontal spindles, an integrated grooving and saw unit, and an SCM electrospindle with HSK 63 F quick-change tool system. Movement paths of the portal and unit carrier Movement in the X, Y, and Z axes is via linear prismatic guideways with preloaded ball bearings. The X-axis movement (moving gantry) uses a preloaded, backlash-free rack-and-pinion drive with helical gearing. Movement of the unit carrier in Y and Z directions is also preloaded for precision. Positioning of the working units and machine function control is through "brushless" AC servo motors and digital drives. CNC CONTROL The control unit comprises a numerical control for the milling and drilling machines and a PC with a graphical user interface "XILOG PLUS". PC office operating system Windows XP - 17" LCD color screen - QWERTY keyboard - Swiveling control panel - Machine interface: Xilog Plus software Xilog Plus Features Programming - Parametric, graphical, and ISO programming - Import of DXF and ASCII files - Linear or circular interpolation on three axes, spatially linear, spirally on selected plane - Supported programming with graphical and syntax assistance for drilling and milling operations - Automatic optimization of drilling operations and tool change cycles - Possibility to shift panel zero point for drilling on slanted or curved panel sides - Full compatibility with CAD/CAM Routocam (SCM) – AlphaCam Integrated additional functions - Calculator for direct transfer of computed data - S

Condition: used, Year of construction: 2005, Used machine Year of manufacture: 2005 Features and Technical Data: - Base machine 555 - Milling dimensions: - X = 3,514 mm - Y = 1,544 mm - Maximum machining dimensions: - X = 3,868 mm - Y = 1,746 mm - Z = 325 mm - Workpiece support with 8 consoles, pneumatically clamped - Drilling unit 7968: - 18 vertical drilling spindles with 32 mm pitch - 12 in the X-axis, 6 in the Y-axis - Individually selectable - T-shape arrangement - Maximum drilling diameter: 35 mm (depending on panel thickness) - Spindle extension stroke: 70 mm - Alternating right- and left-hand rotation - Infinitely variable spindle speed: n = 4,725 rpm - 2 horizontal drilling units in X-direction, 1 horizontal drilling unit in Y-direction - Saw unit 7946: - Motor: 3.5 kW - Pneumatically swiveling to 90° - n = 5,300 rpm - Tool holder: A Ø = 200mm, I Ø = 30mm, B = max. 3.5mm - Sawing/grooving in X and Y directions - Milling unit 7935: Bedpfxjx Enpqe Ak Howl - With 6 kW, water-cooled spindle - Milling unit 7982: - For lock case routing - Tool changer 7996: - 18-position carousel magazine - Vacuum pump with 140 m³/h - Handheld control unit - PC control with TwinCAM WOP system - Siemens control system Availability: short-term Location: 63934 Röllbach

Condition: used, Year of construction: 2016, Used Machine Year of manufacture: 2016 Equipment and technical data: - Electrical system 3x400V 50 / 60Hz - Cardanic 5-axis electrospindle, 12 kW (S6), HSK F63 - 24,000 rpm - Ceramic bearings including liquid cooling with stepless, height-adjustable extraction hood – motor-driven control - Full rated power available at approximately 12,000 rpm - Speed range: 1,000 - 24,000 rpm - Drive: 3-phase high-frequency motor controlled via inverter - Rotation direction: clockwise/counterclockwise - 2 controlled compressed air connections - Interface for aggregates - Tool weight (rotating): 6 kg - Max. saw blade Ø 350 mm - Spindle cooling: liquid cooling - Extraction hood, stepless adjustment Profit H350 16.30: Bwedpjy Ih Rgjfx Ak Hjl CNC machining center in gantry design (without tooling) with digital drives (driven on both sides). The machine frame of the Profit H350 16.30 is made from thick-walled, electrowelded box sections. The internal steel ribbing provides high rigidity. Machining area H350 16.30: Axis travel: X = 4,000 mm Y = 1,970 mm Z = 455 mm Working area: X = 3,000 mm Y = 1,500 mm Z = 150 mm clearance height Axis positioning speeds: Depend on the selected safety system (details available in the layout). - Double-sided driven gantry X-Axis guidance system: The drive for the X-axis gantry is via a rack and pinion with angled, crowned teeth – guaranteeing maximum precision. The reduction gearbox ensures top machining quality and repeatability. Bearing via encapsulated recirculating ball carriages running on hardened and ground linear guides. Y-Axis guidance system: Bearing via encapsulated recirculating ball carriages running on hardened and ground linear guides. The Y-axis is positioned via a ground recirculating ball screw. Z-Axis guidance system: Bearing via encapsulated recirculating ball carriages running on hardened and ground linear guides. The Z-axis is positioned via a ground recirculating ball screw. Automatic central lubrication: Grease is automatically delivered to the guide carriages of X, Y, and Z axes as well as the ball screws of Y and Z axes. The lubrication cycle is executed automatically after a preset interval. 12-position linear tool changer on the left side of the machine frame including a pickup station for aggregates: The 12-position linear tool changer ensures minimal setup times and offers ample space for milling tools. One aggregate change station (see layout for configuration options). Max. tool diameter 250 mm. Max. tool length 240 mm. Drilling head DH 18 6H 1S: Vertically: 12 spindles (7 spindles in X-direction and 5 spindles in Y-direction). Horizontally: 6 spindles (4 spindles in X-direction and 2 spindles in Y-direction). Stroke = 70 mm, max. drill length = 70 mm, shank diameter = 10 mm. All spindles are individually driven and selected. 1 grooving saw in X-direction, max. saw blade diameter 120 mm.

Condition: used, Year of construction: 2005, Used machine Year of manufacture: 2005 Equipment and technical data: Console machine (6 units) Travel dimensions: X = 3490 mm Y = 1690 mm Z = 205 mm Machining dimensions: X = 3050 mm Y = (Max. milling dimension - tool radius) 1345 mm Z = 150 mm Drilling head TF 20 Power: 2.2 kW 8 vertical spindles, spindle spacing 32 mm in X 6 vertical spindles, spindle spacing 32 mm in Y 2+2 horizontal spindles in X 1+1 horizontal spindles in Y with integrated grooving saw blade 120 mm with electro-milling spindle 9.2 kW with ISO-30 interface with C-axis with angle aggregate with 12-position tool changer with tool change station for angle aggregates with vacuum pump 80-100 m³/h Total connected load: 16 kW Compressed air: 6 bar Compressed air consumption: 210 NL/min Extraction nozzle: 250 mm Extraction volume: 5300 m³/h Extraction speed: 30 m/sec Dimensions: 5940 x 3800 x 2510 mm Weight: 3700 kg Availability: by arrangement Location: 63934 Röllbach Bwsdpfx Aey Ih Rmek Hel

Year of construction: 1993, condition: reconditioned (used), year - 1993 / 2020 complete reconditioned with new PLC Management tube diameter max. 100 mm wall thicknes - 10 mm pull up length of tube - 6000 /12000 mm Mandrel pipe bending up to 4 mm pipe wall thickness and pipe bending without mandrel from 5.0 - 10 mm pipe wall thickness accuracy of bending angle ± 0,2 ° total power requirement - 50 kW Bjdjiau Uuepfx Ak Hswl weight of the machine ca. 6 t

Condition: used, Year of construction: 2007, operating hours: 27,953 h, machine/vehicle number: 6915, spindle speed (min.): 10 rpm, spindle speed (max.): 600 rpm, controller manufacturer: Siemens, tool diameter: 600 mm, Denn RL-600 CNC Machine Data Designation: Denn RL-600 CNC Installation Dimensions: approx. 1400 × 5000 × 3500 mm Operating Hours: 27,953 hours Workpiece Data Max. Workpiece Diameter: 600 mm Bwedpfjy E Hgzox Ak Hsl Min. Workpiece Diameter: 100 mm Centre Distance: 5,300 mm Performance Data Main Spindle Speed: 10–600 rpm Max. Feed Rate: 5 m/min Control / Technology CNC Control: Siemens Sinumerik HMI: PC-based control panel USB Port: for backing up the machine program CAD/CAM Interface: DXF (AutoCAD 2002 LT)

Condition: used, CNC Lathe DMG MORI SEIKI - GILDEMEISTER Type CTX 310 ecoline Machine No. 8044001846E Year of manufacture: 2013 CNC Control: SIEMENS Sinumerik 840D sl Swing diameter over bedway cover: 330 mm Swing diameter over cross-slide cover: 260 mm Centre height max.: 190 mm Centre distance max.: 580 mm Turning diameter max.: 200 mm Longitudinal slide travel (Z-axis) max.: 450 mm Cross-slide travel (X-axis) max.: 160 mm Spindle bore through draw tube: 51 mm Spindle bore through front bearing: 100 mm Spindle speed max.: 5,000 rpm Feed rate X and Z: mm/min. Rapid traverse X-axis: 30 m/min. Rapid traverse Z-axis: 30 m/min. Feed force X and Z: 4,500 Nm Tool turret: 12 stations Bwodpjyk Hrgofx Ak Hsl Driven tool stations: 6 stations Tool holder cylindrical VDI 30 mm Spindle drive motor power at 100% duty cycle: max. 11 kW Spindle drive motor power at 40% duty cycle: max. 16.5 kW Power supply: 400 Volt, 50 Hz, 21 kVA - CNC control SIEMENS Sinumerik 840D sl, system software NCU V04.04+SP02+HF02 - Controlled C4-axis chuck position and C1-axis for tool turret - 3-jaw chuck AUTOGRIP Ø 210 mm with 1 set of hard jaws and 15 sets of soft jaws - AUTOGRIP hydraulic hollow clamping device - Clamping force adjustment for regulating clamping pressure - Tool turret SAUTER, type 0.5.901.020 with 12 stations (6 driven) - 20 tool holders VDI 30 - Tailstock MK 4 - Indirect measurement system via rotary encoder - Chip conveyor with integrated coolant system - Workpiece residual life display and piece counter as large display on machine enclosure - Control cabinet cooling unit - 9,716 total operating hours (main switch on), of which 3,322 spindle hours as per counter - Operating instructions and manuals Machine footprint with chip conveyor (L x W x H): 4,500 x 2,600 x 2,050 mm Base machine space requirement (L x W x H): 2,900 x 2,150 x 2,050 mm (3,200 kg) Chip conveyor space requirement (L x W x H): 3,350 x 850 x 1,650 mm (500 kg) Weight: approx. 4 tons Very good condition

Condition: used, Year of construction: 2011, Base Machine M800 X5 TV 1 WORKING RANGE X: 5,020 mm Y: 1,830 mm Z: 675 mm Clearance Height: 300 mm (from 50 mm suction cup height) MACHINE STRUCTURE The base structure is a monolithic construction made from thick-walled steel. It is reinforced across the entire machine bed with welded components, providing exceptional stability. The table design, with its large base, is the key to ensuring lasting precision and stability. The machine’s layout enables the operator to achieve optimal workflow with minimal space requirements. The mobile gantry is built as a solid monoblock. It is positioned in the X direction on prismatic, ground guides with recirculating ball carriages. The machining unit is mounted on this mobile support carriage, also on prismatic, ground guides and recirculating ball carriages. AXIS MOVEMENT All axes travel on prismatic linear guides with large cross-section and recirculating ball shoes with a wide contact surface, which ensures optimal sliding, even at high speeds and accelerations. The precise and fast positioning of the movable gantry (X-axis) is achieved via helical rack and pinion. Large cross-section recirculating ball screws ensure accurate positioning of the machining unit along the movable gantry (Y and Z axes). The perfect mechanical dynamics and maximum positioning accuracy are controlled by high-quality drives and brushless motors. Max. axis speeds: · X-axis = 90 m/min · Y-axis = 90 m/min · Z-axis = 30 m/min Safety device with bumper and light barrier 1 Bumpers with sensors are fitted to the movable upright, and a light barrier system is installed at the front of the machine. If the operator enters the active zone, the X-axis travel speed is reduced to a lower value of 25 m/min without stopping the machine. This system allows parts to be loaded during pendulum operation without the limitation of access areas, as seen with pressure mat systems. This prevents unwanted interruptions in the machining cycle and offers greater freedom of movement around the worktable. CE certification for the safety system 1 Safety protection fence 1 Side and rear protection fence Automatic central lubrication controlled via CNC 1 The lubrication of the X, Y, and Z axes is controlled by the CNC; intervals are regulated automatically, without manual intervention. Central extraction connector 1 All individual extraction connections of the machining units are collected into a central extraction port. Inside the port, there are various slider valves controlled by the NC. This reduces the required extraction air volume. Chip conveyor 1 Maxi – 5-axis electrospindle 11 kW HSK-63 “Prisma K 1 5-axis electrospindle, 11 kW at 20,000 rpm S1 (100% duty cycle) Speed: max. 20,000 rpm Rotation direction: left/right Liquid cooling Tool interface HSK 63F Inverter 18 kW, stepless, smooth power delivery Max. rotation B-axis = 200° (+-100°) C-axis = 650° Thanks to the non-orthogonal axes, it is possible to perform complex horizontal positioning in a small workspace. This enables the machining of complex geometries without the risk of collision. Bjdpfsxy Tmnex Ak Howl

Condition: used, Year of construction: 2016, Working area: X=3300 mm Y=1280 mm Z=150 mm Clearance height Operator terminal: 24" LED colour display Handheld terminal for axis speed control Software: "Woodflash Vacuum pump 90 m³/h/50 Hz or 108 m³/h/60 Hz Milling spindle 12 kW HSK F63 (12,000 rpm) 12-position linear tool changer on the left of the machine frame + pickup station Drilling head DH 16 4H 2S: Vertical 12 spindles Horizontal 4 spindles 2 grooving saws Storage location: Nattheim Bwjdpfx Ajxy Tlwek Hol

Condition: good (used), Year of construction: 2008, Ref. -No.: 10626 Manufacturer: DMG Type: DMU 210 P Year of construction: 2008 Type of control: CNC-Steuerung Control: Heidenhain ITCN 530 Storage location: Halberstadt Country of origin: Germany X-Travel: 1800 mm Y-Travel: 2100 mm Z-Travel: 1250 mm B-Axis: -30 / +180 ° Bwodpey H Er Ejfx Ak Hel C-Axis: 360 ° Table Load: 8000 kg Clamping Area: 1.700 mm Tool Taper: HSK - 100 Spindle Speed: 10.000 RPM Max. Torque: 288 Nm No. Of Working Stations: 60 coolant reservoir: 40 bar L. Further information: - The DMG DMU 210 P 5-axis machining center is suitable for high-precision machining of large, heavy workpieces. - Direct position measuring systems in all axes - Heidenhain TS workpiece measurement - Electronic handwheel setup mode - Chip conveyor chip disposal - Double gripper tool changer - Motor spindle technology The machine can be viewed under power by arrangement.

Condition: good (used), Year of construction: 2011, Ref. -No.: 10615 Manufacturer: DMG Type: DMU 210 P Year of construction: 2011 Type of control: CNC-Steuerung Control: Heidenhain ITNC 530 Storage location: Halberstadt Country of origin: Germany Machine-No.: 128/XXXX X-Travel: 1800 mm Y-Travel: 2100 mm Z-Travel: 1250 mm Swivel range: -30 / +180 ° Table Load: 10000 kg Max. rotary table diameter: 1700 O Table speed range: 12 min/-1 Tool Taper: HSK 63 Numbers Of Tools In Magazin: 60 Spindle Turning Speed - Stepless: 24.000 RPM Weight Of The Machine Ca.: 41 t Motor spindle: 24000 RPM Bedpoy H Epwsfx Ak Hjwl Feed drive A, C: 30 min/-1 horizontal milling head: 130-1.380 mm vertical milling head: 230-1.480 mm Further information: The machine can be viewed while powered up.

Year of construction: 2009, condition: used, Used machine Year of manufacture: 2009 Condition: well-maintained Point-to-point drilling machine Working width: 800 mm with grooving unit Drilling head with 7 vertical drilling spindles and 1 horizontal double drilling spindle in X-axis direction 1 drilling spindle in Y-direction Grooving saw unit in X-direction 3-axis control X: NC-controlled feed of workpiece via overlapping pneumatic clamping gripper Y: NC-controlled drilling movement Z: NC-controlled drilling depth adjustment Pneumatic roller hold-downs in feed area Pneumatic clamping gripper for transport DXF interface 15" color screen Keyboard including mouse Network card USB interface Max. panel width: 950 mm Max. drilling width: 800 mm Max. processing width for back panel grooves: 600 mm Max. feed speed (X-axis): 30 m/min Max. drill bit diameter: 35 mm Max. total drill length: 70 mm Connected load: 2.5 kW Extraction port: 100 mm Required pressure: 6 bar Bwodpfxow Tfxqe Ak Hol Working height: 900 mm Machine dimensions (LxW): 1650 x 2100 mm Availability: Short-term Location: Solingen

Condition: used, Year of construction: 2019, Used machine Year of manufacture: 2019 Equipment and Technical Data: - For classic nesting processing with wear plate - Machine frame of welded construction with ground and hardened prism guides for the gantry, unit head, and consoles - Gantry-type traveling column - Helical rack and pinion drive in X and Y axes, ball screw in Z axis for precise positioning - Working dimensions: - Max. support area on nesting table: X = 3100 mm, Y = 1560 mm - Max. traverse paths: X = 4695 mm, Y = 2100 mm, Z = 293 mm - Max. clearance height over DYNESTIC table: Z = 100 mm from table top (without wear plate) - Maximum programmable speed Vector speed: 128 m/min X = 80 m/min, Y = 100 m/min, Z = 25 m/min - DYNESTIC table: - Fixed, continuous processing table with grid layout - Continuous grooves in X and Y directions - Groove spacing: 50 mm - Includes 25 meters of sealing cord for clamping the wear plate - Vacuum fields: Single-circuit vacuum system - Drilling unit 7877: - 19 spindles - Drive power: 1.7 kW - 13 vertical spindles: - Individually selectable - Arranged in U-shape - 5+4 in X direction, 4 in Y direction - 32 mm spacing - Max. drill diameter: 35 mm - Total drill length: 70 mm from screw-on end (depending on panel thickness) - Spindle stroke: 70 mm - Rotational direction: alternating clockwise/counterclockwise - Speed (max): 1000 - 4400 rpm, infinitely variable - Tool holder: M10 thread, 11 mm fit - Without tool, without holder Bwsdpfxswka Upo Ak Hsl - 6 horizontal spindles: - 2 double drill spindles in X direction - 1 double drill spindle in Y direction - Tool holder: M10 thread, 11 mm fit - Max. total drill length: 63 mm from screw-on end - Without tool, without holder - Milling unit 7842: - Power: 12.0 kW (S6) - Max. speed = 1000 - 24,000 rpm, infinitely variable - Max. power at 12,000 to 24,000 rpm - Air-cooled - With HSK-F 63 tool holder - With right-hand threaded nut (for right-hand rotating tools) - With collet chuck for HSK shank - Ceramic ball bearings (hybrid bearings) - Tool weight max. 6 kg (incl. holder) - Tools: milling and grinding tools max. Ø 160 mm - Safety enclosure according to CE standard - Side and rear safety fence - Vacuum pump: 500 m³/h, dry-running - Personnel safety ensured by light barriers in the front machine area - Hand-held control device for remote operation of the machine with the following functions: - Start/stop of the processing program - Control of processing cycle speed - Reset button - Manual feed/rapid traverse for all axes - EMERGENCY STOP - CAMPUS V7 CAD/CAM software 1x machine license consisting of: - CAMPUS NC-HOPS: - Graphic variant system with WOP and CAD/CAM features for creating part variants using macro technology - CAMPUS MT-Manager - CAMPUS Workcenter - CAMPUS DXF interface - Automatic central lubrication - Automatic lubrication at defined intervals - Additional sealing against dust via pressurization in each guide carriage

Condition: used, Year of construction: 2019, total height: 2,450 mm, total length: 9,500 mm, total width: 2,400 mm, Colour: Grey Empty weight: 5.000 kg Price: On request CNC SCM Morbidelli M100  Brand SCM Type Morbidelli M100  Year of construction 2019 Serial number AA100001570 Machining table dimensions 5510x1620 mm (LxW) 400 Volt / 50 Hz PRO-Speed safety system TEPCAD control panel with touchscreen colour display TBR14 linear tool changer (Y=1620 positions) FAST14 linear tool changer Air blower on electro spindle Guard rails X-Y axes Vacuum pump 150/300 m3/h  50/50 Hz 5-axis unit ‘JQX’ version, 13.5 kW Fixed pod 145x145 H=75 mm Rotating pod 145x55 H=75 mm Clamp for 8 rails TV FLEX / TV FLEXDRIVE / TV FLEXMATIC MULTIGRIP 90 round clamp (H83) for TV FLEX / TV FLEXMATIC Maestro connect: 1 year (gateway kit ‘plug&play’ included) SCM DIGITAL SOLUTIONS: MAESTRO CONNECT MAESTRO ACTIVE human-machine interface software (HMI) Maestro software for cnc programming Hardware key for Maestro cnc Advanced Maestro 3D module Additional key for Maestro cnc (USB port) Windows 10 embedded 64-bit operating system Console with integrated PC ‘eye-M PRO’ Axis movement  Maximum vectorial speed in rapid traverse XY axis 56 m/min Stroke of the Z axis 180 mm Bsdpfxownibtj Ak Hjwl Routing unit Motor power 5.5 kW  Speed 4000 rpm Tool changer up to 44 locations Air consumption 4430 m3/h Air speed 25 m/sec Connection diameter 250 mm Total dimensions 9700x5020x2650 (LxWxH) - Year: 2019 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: AA10001570 - Number of milling spindles [pcs.]: 1 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 5 - - Main motor power [kW]: 13.5 - Type milling table: Beam table - Tool clamping system: HSK-F63 - System/software: Maestro - Safety feature: Bumper guard, Enclosed fence - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: Becker - Tools included: Yes - CNC options: Offcut conveyor - CNC documentation available: USB stick - Working range X [mm]: 5515 - Working range Y [mm]: 1620 - Z-axis working range [mm]: 180 - Transport dimensions: 9500mm x 2400mm x 2450mm (l x w x h) - Transport weight [kg]: 5000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2014, total height: 2,800 mm, total length: 6,900 mm, total width: 2,800 mm, Empty weight: 6.100 kg - Details: - └ Description: Needs repair to B-axis and leaks to seals Bodpfeyr Rnuex Ak Hswl - Year: 2014 - Documentation available: No - CE certificate present: No - Serial number: 10333 - Number of milling spindles [pcs.]: 2 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 5 - └ Milling spindle 2: - - Number of controlled axes [pcs.]: 3 - Type milling table: Beam table - Drilling unit present: Yes - Tool changer positions [pcs.]: 45 - Vacuum pump present: Yes - └ Number [pcs.]: 2 - └ Brand: Becker - └ Type: Vtlf 2.250 - └ Year of manufacture: 2011 - └ Main motor power [kW]: 5.5 - └ Capacity [m³/h]: 244 - └ Connection diameter [mm]: 60 - └ Vacuum pressure [bar]: 200 - └ Oil free: Yes - Tools included: Yes - Table length [mm]: 4800 - Table width [mm]: 1500 - Voltage [V]: 400 - Current consumption [A]: 39 - Fuse [A]: 63 - Power [kW]: 22.8 - Transport dimensions: 6900mm x 2800mm x 2800mm (l x w x h) - Transport weight [kg]: 6100kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2022, Empty weight: 4.000 kg Price: On request - Year: 2022 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Serial number: 30B.11.040.22 - Type milling table: Beam table - Drilling unit present: Yes - └ Horizontal drill spindles [pcs.]: 4 - └ Vertical drilling spindles [pcs.]: 12 - Saw unit present: Yes - Tool changer positions [pcs.]: 12 - Vacuum pump present: Yes Bjdpfx Asx Tt Unok Hswl - └ Number [pcs.]: 1 - └ Brand: Becker - └ Type: PICCHIO 2200 - └ Year of manufacture: 2022 - Tools included: Yes - Working range X [mm]: 3300 - Working range Y [mm]: 1280 - Z-axis working range [mm]: 250 - X-axis maximum stroke [mm]: 4000 - Y-axis maximum stroke [mm]: 1670 - Z-axis maximum stroke [mm]: 500 - Voltage [V]: 400 - Current consumption [A]: 40 - Power [kW]: 18.0 - Transport weight [kg]: 4000kg - Transport packages [pcs.]: 2 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2014, operating hours: 11,517 h, Empty weight: 6.000 kg - Year: 2014 - Documentation available: No - CE certificate present: No - Serial number: 070614/B/1-407 - Operating hours: 11517 - Number of milling spindles [pcs.]: 1 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 4 - - C-axis present: Yes Bwsdpex E Uk Usfx Ak Hel - Type milling table: Flat table - Drilling unit present: Yes - └ Horizontal drill spindles [pcs.]: 6 - └ Vertical drilling spindles [pcs.]: 18 - Tool changer positions [pcs.]: 12 - Vacuum pump present: Yes - └ Number [pcs.]: 2 - └ Brand: Becker - └ Year of manufacture: 2023 - └ Main motor power [kW]: 18.5 - └ Capacity [m³/h]: 600 - └ Vacuum pressure [bar]: 250 - Working range X [mm]: 7220 - Working range Y [mm]: 1580 - Z-axis working range [mm]: 180 - Transport weight [kg]: 6000kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2018, total height: 2,300 mm, total length: 3,870 mm, total width: 1,900 mm, Empty weight: 2.500 kg - Year: 2018 - Documentation available: Yes - CE marking present: Yes - CE certificate present: Yes - Serial number: AH/121500 - Number of milling spindles [pcs.]: 12 - Type milling table: Flat table - Drilling unit present: Yes - Saw unit present: Yes - Tool changer positions [pcs.]: 8 - Tools included: Yes - Table length [mm]: 2570 - Table width [mm]: 1290 - Working range X [mm]: 2486 - Working range Y [mm]: 1255 - Z-axis working range [mm]: 150 - X-axis maximum stroke [mm]: 3120 - Y-axis maximum stroke [mm]: 1685 - Z-axis maximum stroke [mm]: 250 - Transport dimensions: 3870mm x 1900mm x 2300mm (l x w x h) Bwodpfxsxrdngs Ak Hsl - Transport weight [kg]: 2500kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2018, operating hours: 10,347 h, - Year: 2018 - Documentation available: Yes - CE marking present: Yes - CE certificate present: Yes - Operating hours: 10347 Bwjdpfxsxtbgpj Ak Hol - Number of milling spindles [pcs.]: 1 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 5 - Type milling table: Beam table - Drilling unit present: Yes - └ Horizontal drill spindles [pcs.]: 10 - └ Vertical drilling spindles [pcs.]: 24 - Saw unit present: Yes - Tool changer positions [pcs.]: 25 - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: Becker - Working range X [mm]: 3110 - Working range Y [mm]: 1320 - Z-axis working range [mm]: 180 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, Year of construction: 2012, total height: 2,400 mm, total length: 13,500 mm, total width: 2,450 mm, Empty weight: 2.500 kg Biesse Rover A1536 G FR Bwodpfx Akswnip Do Hel Year 2012 Central lubrifaction FT work table, X 3765 Y 1560, 9 zones 12 kW electro spindle, ISO 30, air cooled Biesse WORKS Biesse NEST MODULE Air conditioner 16 pos. revolver magazine Work area XYZ 3765*1585*170 2x vacu pump 250 m³ C axis 360° BH 17 L drilling group Including loading and unloading system - Year: 2012 - Documentation available: Yes - └ Type Documentation: User manual, Electrical diagrams - └ Type: Hardcopy - CE marking present: Yes - CE certificate present: No - Serial number: 81399 - Type milling table: Flat table - Drilling unit present: Yes - └ Horizontal drill spindles [pcs.]: 4 - └ Vertical drilling spindles [pcs.]: 7 - Saw unit present: Yes - Tool changer positions [pcs.]: 16 - Vacuum pump present: Yes - └ Number [pcs.]: 2 - └ Brand: Becker - └ Capacity [m³/h]: 250 - Working range X [mm]: 3765 - Working range Y [mm]: 1585 - Z-axis working range [mm]: 170 - Transport dimensions: 13500mm x 2450mm x 2400mm (l x w x h) - Transport weight [kg]: 2500kg - Transport packages [pcs.]: 4 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets