Used Cnc Turning Machine for sale (66,687)

Condition: used, CNC turning machine TRAUB, Type TND 400 Serial No. 708, Year of manufacture 1996 CNC control TRAUB TX 8 F Nominal turning diameter: 400 mm Swinging diameter over bed: max. 470 mm Spindle bore in draw tube: 65 mm Motor power, spindle drive: 22 kW Total power consumption: 35 kW Mains connection: 380 volts, 50 Hz - Electronic handwheel - RS 232 data interface - Turret with 12 tool positions, VDI 40 - Includes 8 tool holders, VDI 40 - 3-jaw chuck, Ø 225 mm, SMW Autoblok, Type KNCS-N-Ø 225-65 Includes a large quantity of chuck jaws - Hydraulic internal expanding cylinder, SMW, Type ZHDAS-130-67 - Chip conveyor, KNOLL, Type 200 S-1/600 - Coolant system - Hydraulic unit (L x W x H 650 x 500 x 1000 mm) Space requirement L x W x H: 4800 x 2000 x 2100 mm Space requirement, base machine L x W x H: 3500 x 2000 x 2100 mm Space requirement, chip conveyor L x W x H: 4500 x 700 x 1550 mm Weight: approx. 5 tons Godpfx Ajzacwdepwska Good condition Machine is ready for demonstration. The internal expanding cylinder for workpiece clamping needs to be repaired.

Year of construction: 2018, condition: ready for operation (used), Machining processes: drilling, turning, milling, axes: Z3 longitudinal slide tool turret, Z4 longitudinal slide tool turret, X3 cross slide tool turret, X4 cross slide tool turret, C1 workpiece drive, C2 workpiece drive, K5 turret swivel axis, K6 tool drive, K7 turret swivel axis, K8 tool drive, travel X3: 251mm, X4: 251mm, Z3: 662mm, Z4: 662mm, tool turret: 12-station radial, DIN 69880-VDI40, drive: DIN 5480-W20x0.8, tool swing diameter: 580mm, specified dimension at tool area: 320mm, length: 13,000mm, width: 7300mm, height: 4100mm, weight: 22t, operating hours: 14,748h. Equipment: OP012 control panel, Kuka handling robot, chip conveyor, coolant tank, hydraulics, pneumatics, electrical cabinet, parts infeed and outfeed, documentation, installation plan, working area diagram, gearbox plan and transport plan. The following components should be overhauled: machine bed (guideways/ball screws), motor spindles with release units (replace bearings/reseal), cross slides (guideways/ball screws/motor), workpiece spindle (replace bearings/reseal), protective enclosure (interior cladding/working area door/repaint machine), coolant pumps, replacement of electrical cables/lubrication and hydraulic lines, as required. An on-site inspection is possible. Gedpfx Apeztducoweka

Condition: good (used), Year of construction: 2001, Ref. -No.: 10551 Manufacturer: TRAUB Type: TNC 42/65 Year of construction: 2001 Type of control: CNC-Steuerung Control: TRAUB TX Storage location: Halberstadt Country of origin: Germany Machine-No.: 93XXXXX Turning Speeds: 8000 RPM X stroke: 450 mm Turning Length: 450 mm Spindle Speeds: 4000 RPM Clamping Diameter: 42 / 65 mm Spindle Diameter In Front Bearing: 110 mm Tool Taper: 14 Max. Torque: 170 / 230 Nm Gedpfx Aozkpvmjpweka Rapid Travel Speed X-Axis: 15 m / min Rapid Travel Speed Y-Axis: 6 m / min Rapid Travel Speed Z-Axis: 30 m / min Dimensions Of The Machine (Lxwxh): 4354 x 2076 x 1917 m Chisel slide cross section turning and milling support: 16 x16 ( 20 x20 ) mm Pressure: 70 bar hydraulic tank: 70 L. Total Power Requirement: 39 kVA Weight Of The Machine Ca.: 5,2 t Feed force X-axis at 100% duty cycle: 5000 N Feed path X-axis: 140 mm Z-axis feed path: 450 mm Y-axis feed path: 35 mm Ball screw Z-axis (Ø x pitch): 32 x 10 mm Ball screw X-axis (Ø x pitch): 32 x 5 mm Ball screw Y-axis (Ø x pitch): 25 x 5 mm Further information: - Revolver 1 Number of branches 10 - Revolver 2 Number of branches 14 - Hecowpkfie Htlx Tfefh - Powered tools Yes The machine can be viewed under power by arrangement.

Year of construction: 2007, condition: ready for operation (used), A vertical EMAG CNC turning machine is available. Turning diameter: 400mm, swing diameter: 420mm, X/Z-axis travel: 850mm/315mm, spindle bearing diameter: 140mm, spindle speed: 4000rpm, rapid traverse X/Z: 45m/min/30m/min, feed force: 11kN, machine dimensions X/Y/Z: approx. 9500mm/4500mm/3000mm, weight: approx. 9000kg. Including hard turning function, dry machining function and chip conveyor. Documentation available. An on-site inspection is possible. Gkodpfx Apjznmxtowja

Condition: good (used), Year of construction: 1998, Ref. -No.: 10548 Manufacturer: MONFORTS Type: RNC 5 A17 Year of construction: 1998 Type of control: CNC-Steuerung Control: Monforts Storage location: Halberstadt Gksdoxmd T Eopfx Apwja Country of origin: Germany Machine-No.: 303XXXX Chuck diameter: 250 mm Centre Distance: 1080 mm Spindle Diameter In Front Bearing: 100 mm Spindle head according to DIN 55027 (size): Gr. 8 Circumferential diameter over radial slide: 290 mm Max swing diameter: 500 mm travel of the cross slide: 265 mm Tailstock outside diameter of the quill: 80 mm Tailstock maximum quill stroke: 160 mm Tailstock inner cone: MK 5 Type Material flow max.: 70 mm Turning Speed Range: 2 - 2800 rpm Further information: The machine can be viewed under power by arrangement.

Year of construction: 2003, condition: ready for operation (used), A vertical CNC lathe by Emag is available. Workpiece length range: 22mm-100mm, turning length: 100mm, speed: 6500rpm, measuring length: 94mm, max. swing diameter: 220mm, tool stations: 12, weight: approx. 7000kg. Including tool setting probe, carousel workpiece transfer system, chip conveyor and coolant system. Documentation available. An on-site inspection is possible. Gksdpfx Ajzl Emqspwea

Year of construction: 2004, condition: ready for operation (used), A vertical EMAG CNC turning machine with automation is available. Speed: 6500rpm, workpiece length range: 22mm-100mm, turning length: 100mm, measuring length: 94mm, max. swing diameter: 220mm, max. pump pressure: 120bar, tool stations: 12, loading stations: 2, robot type: M-10iA, control: Fanuc 16i-TB, weight: approx. 10000kg, power-on hours: 84847h. Including high-pressure pump, tool setting probe, chip conveyor, coolant system, workpiece shuttle system and robot automation. Documentation available. An on-site inspection is possible. Gkedpfx Ajzl Enbopwsa

Year of construction: 2010, condition: ready for operation (used), A vertical CNC lathe Emag is available. Speed: 4500rpm, Tool stations: 12, Travel X/Z: 570mm/200mm, Max. chuck diameter: 260mm, Max. turning diameter: 260mm, Max. machining diameter: 220mm, Max. workpiece length: 110mm, Rapid traverse X: 60m/min, Rapid traverse Z: 30m/min, Feed force: 5.5kN, Max. workpiece weight: 120kg, Weight: approx. 6500kg, Control: Siemens Sinumerik 840. Documentation available. An on-site inspection is possible. Gjdpfozl Em Dox Apwoka

Year of construction: 2004, condition: ready for operation (used), A vertical EMAG CNC lathe is available. Workpiece length range: 22mm-100mm, turning length: 100mm, max. swing diameter: 220mm, tool stations: 12, measuring length: 94mm, spindle speed: 6500rpm. Machine dimensions X/Y/Z: approx. 2400mm/3300mm/2950mm, weight: approx. 10000kg. Including tool setting probe, chip conveyor, 120bar high-pressure pump, Heilig workpiece shuttle system with two stations and coolant system. Documentation available. An on-site inspection is possible. Godjzl El Tspfx Apwjka

Year of construction: 2004, condition: ready for operation (used), A complete turning system consisting of two identical EMAG vertical turning machines together with the associated peripheral equipment and automation is available. Main spindles: 2, Speed: 6500rpm, Tool stations: 2x12, X/Z-axis travel: 840mm/425mm, Robot type: M-6iB, Loading stations: 2, Workpiece carriers: 24, Weight: approx. 8000kg, Power-on hours 1/2: 51170h/53006h, Feed/Machining time 1/2: 33418h/30961h, Automatic operation hours 1/2: 14858h/14709h. Both machines are equipped with chip conveyors, 2x tool turrets, 2x loading stations, a workpiece palletizing system, robot automation and coolant system. Documentation available. An on-site inspection is possible. Godpfxezl Emdo Apwjka

Year of construction: 2004, condition: ready for operation (used), A complete turning system consisting of two identical EMAG vertical turning machines together with the associated peripheral equipment and automation is available. Main spindles: 2, Speed: 6500rpm, Tool stations: 2x12, X/Z travel: 840mm/425mm, Robot type: M-6iB, Loading stations: 2, Workpiece carriers: 24, Weight: approx. 8000kg, Power-on hours 1/2: 42668h/42411h, Feed/Machining time 1/2: 29058h/27736h, Automatic operation hours 1/2: 10354h/12404h. Both machines are equipped with chip conveyors, 2 tool turrets, 2 loading stations, a workpiece palletizing system, robot automation and cooling. Documentation available. An on-site inspection is possible. Godozl Emkopfx Apwjka

Year of construction: 2003, condition: good (used), Sub-spindle, Y-axis, B-axis SIEMENS 840D Powerline Turning diameter max 200mm Turning length -635mm Swing Diameter -250mm Spindle speeds main & sub-spindle 20-7000 rpm Gedpfoglf A Hjx Apwoka Turret head 1+2: 12 driven positions B-Axis, upper turret head +135/-45° Misc. accessories MARCELS MASCHINEN CH

Condition: ready for operation (used), Year of construction: 2012, QuickTech T8 Twin turning machine with Gegenspindel , C axis, 12 place head, with FMB Loader Gksdjil Hi Hepfx Apwsa

Condition: used, Year of construction: 1998, operating hours: 97,593 h, functionality: fully functional, turning diameter: 65 mm, spindle bore: 79 mm, spindle speed (max.): 4,500 rpm, spindle speed (min.): 25 rpm, For Sale: Gildemeister MF Sprint 65 CNC Sliding Headstock Lathe with 3-Meter Bar Feeder, as shown in the pictures. The machine was removed from our workshop in fully functional condition. A video of the machine in operation prior to disassembly is available upon request. Approximately five years ago, the linear guides of the X1 and Z1 slides (on the main spindle side) were replaced, including bearings and belts. A new HMI interface was installed recently. Detailed specifications and technical data can be found in the attached PDF. TECHNICAL DATA Control: Sinumerik 840C Bar Feeder: SIMAG 65.1-3200G, Year of Manufacture: 1998 Bar Length: 3 meters Bar Diameter / Spindle Bore: 65 mm Main Drive Power Output: 28 / 21 kW Speed Range: 25 – 4,500 rpm Torque: 320 / 240 Nm Maximum Feed Rate for Thread Cutting: 10 m/min C-Axis Speed: 120 rpm C-Axis Torque (Holding Torque): 180 Nm Tool Carrier Number of Tool Stations: 8 Shank Diameter (DIN 69880): 30 mm Number of Driven Tool Stations: 4 Power Output: 7.6 / 4.6 kW Gkjdswym Nfjpfx Apwsa Torque: 24 / 14.7 Nm Maximum Speed of Tool Carrier 1: 4,000 rpm Maximum Speed of Tool Carrier 2: 4,000 rpm Slide 1 Cross Travel / Longitudinal Travel: 155 / 280 mm Rapid Traverse Speed X/Z: 22.5 / 22.5 m/min Feed Force X/Z: 900 / 900 daN Slide 2 Cross Travel / Longitudinal Travel: 82 / 120 mm Rapid Traverse Speed X/Z: 22.5 / 22.5 m/min Feed Force X/Z: 900 / 900 daN MACHINE DATA Dimensions with Bar Feeder and Chip Conveyor (L × W × H): approx. 6 × 2 × 2 meters Weight: approx. 6.5 tons Operating Voltage: 50 Hz, 400 V Accessories: Cooling System Chip Conveyor Documentation The offer is subject to change and non-binding, changes and errors in the technical data or the equipment, as well as prior sale reserved Used machines are purchased as seen, without warranty claims. Delivery ex works excluding packaging and insurance, unless otherwise agreed. The price does not include statutory value added tax. As is usual with used machines, payment is made before loading.

Condition: good (used), Year of construction: 2008, 1 used CNC turning/milling center Gildemeister type TWIN 65 RG 2 year 2008 with Siemens 840 D Maximum turning length (travel in the Z axis) 650 mm Maximum turning diameter over bed 250 mm Maximum length of travel in the X-axis 300 mm Maximum feed speed X-axis 30 m/min Maximum feed speed Z axis 30 m/min Maximum main spindle power 35 kW Gkodjq T I Izepfx Apwsa Spindle diameter 65 mm Minimum main spindle speed 20 1/min Maximum main spindle speed 5000 1/min Lathe length 7000 mm Lathe width 4700 mm Lathe height 2500 mm Lathe weight 10 t Machine equipment Y axis Irco loading magazine ILS RBK 1200 mm Workpiece pick-up device Technical data Errors excepted Please note that the machine is sold without chucks, as these remain with the seller!

Condition: excellent (used), Year of construction: 2019, Sub-spindle, C-axis SIEMENS 840DSL Turning diameter max 16 mm Turning length 145mm Spindle speeds main & sub-spindle 15'000 rpm Tool holder group 1+2: 6 driven positions Gjdpfjud Nhhjx Apwoka C-Axis 0.001° Misc. accessories MARCELS MASCHINEN CH

Condition: used, As-new CNC chuck lathe TAIKAN model HPT 08-380 Serial No. 2015122 Year of manufacture: 2017 CNC path control: SIEMENS Sinumerik 828 D Basic Maximum turning length without chuck: 350 mm Maximum turning length with chuck: approx. 300 mm Turning diameter (nominal): 250 mm Swing diameter over bed: 500 mm Travel of Z-axis: 385 mm Travel of X-axis: 200 mm Feed rate (X + Z): 1–8000 mm/sec. Rapid traverse (X): 30,000 mm/sec. Rapid traverse (Z): 36,000 mm/sec. Spindle speed, max.: 4500 rpm Spindle bore: 66 mm Draw tube bore: 50 mm Spindle nose: presumably A2-6 Workpiece weight incl. chuck: max. 200 kg Spindle drive motor power: 11 kW Power supply: 400 Volt, 50 Hz - Electronic handwheel - USB, LAN data interface + CF card - Drum turret with 12 tool stations - Hydraulic 3-jaw power chuck, Ø 215 mm - Infinitely variable spindle speed - Coolant unit - Chip conveyor with rear discharge + basic chip cart Machine footprint with chip conveyor: Length 2200 mm x Depth 2750 mm x Height 1700 mm Gksdswz Rifepfx Apwoa Machine space requirement: Length 2200 mm x Depth 1750 mm x Height 1700 mm Chip conveyor dimensions: Length 2700 mm x Width 600 mm x Height 1400 mm Weight: 3.5 t Very good condition – as new Machine comes from a showroom and has only a few operating hours.

Condition: ready for operation (used), Year of construction: 2007, Make: MAZAK Type of machine: QuickTurn Nexus 250-II Gedpfx Apey I Uviowjka Year of manufacture: 2007 Control system: Mazatrol Matrix Nexus Machine's weight: 5.200 kg Tool holder: BMT Speed range: 4.000 1/min Cutting diameter: 380 mm Turning length: 500 mm Tool turret - slots: 12 Pl. Spindle opening: 76 mm

Condition: excellent (used), Sub-spindle, Y-axis, C-axis FANUC 18i-TB control Turning diameter max 250 mm Turning length -555 mm Chuck Diameter -165 mm Main-spindle speeds 50-4'500 rpm Sub-spindle speeds 5'000 rpm Turret head 1+2: 24 positions with 12 driven positions each Tool presetting device Gedpex A Eupofx Apweka Barloader Piece catching device Misc. accessories MARCELS MASCHINEN CH

Condition: excellent (used), Year of construction: 2015, operating hours: 11,100 h, functionality: fully functional, machine/vehicle number: NTX1150102, Year 2015 with F31iB5 control and CELOS Country of manufacture: JP Voltage: 380V/50Hz/3ph Dimensions: 4169x2543x2543 mm Net machine weight: 10,000 kg TECHNICAL SPECIFICATIONS Control: Fanuc F31iB5 with CELOS Main spindle: X1 axis: 455 mm Y axis: +/- 105 mm Z1 axis: 800 mm (+165 for ATC) B axis: 240° Turret 2: X2 axis: 160 mm Z2 axis: 730 mm Spindle 1 / Spindle 2: C axis: 360° / 360° Tailstock: A axis: 820 mm Max. distance between centres: 1,050 mm Max. turning diameter Main spindle: Ø 430 mm Turret 2: Ø 274 mm Gjdpew T Snfefx Apwjka Max. turning length: 800 mm Bar diameter: Ø 52 mm . Ø 65 mm Unless otherwise specified or in case of errors or omissions, the technical data is provided without commitment.

Condition: excellent (used), Year of construction: 2020, operating hours: 4,800 h, functionality: fully functional, machine/vehicle number: NL154200702, Manufacturing origin: JP Voltage: 380 V / 50 Hz / 3-phase Net weight: 5,400 kg Customs tariff number: 8458.9100 TECHNICAL DATA Maximum turning diameter: 350 mm Turning length: 515 mm CNC control: M730UM MAPPS Celos Swing over bed: 923.8 mm Swing diameter above carriage: 755 mm Standard turning diameter: 260 mm Bar capacity: 34 mm Main spindle: Spindle speed range: 100 – 8,000 rpm Spindle motor power: 11 / 7.5 kW C-axis resolution: 0.001° Chuck diameter: 210 mm Subspindle: Maximum speed: 8,000 rpm Spindle nose: A2-5 Axis travels: X-axis travel: 260 mm Z-axis travel: 580 mm Y-axis travel: 100 mm (±50 mm) Gjdpfx Apjw T Sn Ejwoka Turret: Number of turret stations: 20 Driven stations: 20 Tool shank diameter: 25 mm Maximum driven tool speed: 10,000 rpm Driven tool motor power: 5.5 / 3.7 kW Feed rates: Rapid traverse X-axis: 30 m/min Rapid traverse Z-axis: 30 m/min Rapid traverse subspindle: 30 m/min Rapid traverse Y-axis: 10 m/min Rapid traverse C-axis: 400 rpm Total power requirement: 31 kVA Approximate machine weight: 5.4 t Approximate machine dimensions: 4.0 x 3.0 x 3.2 m Errors and omissions excepted – data provided without obligation.

Condition: excellent (used), Year of construction: 2001, operating hours: 47,600 h, machine/vehicle number: 325, System: TX8H Spindle passage: 80 mm Gjdpfx Apeh Dzqlowska Turning length max: 750mm Turning diameter: 340mm Power: 22kw Number of tool holders: 12 Shaft diameter: 40 Powered tools in all positions X axis Z axis C axis Automatic tailstock chip conveyor

Year of construction: 2003, condition: ready for operation (used), An EMAG CNC vertical lathe is available. Chuck diameter: 250mm, orbital diameter: 260mm, travel X/Z: 570mm/200mm, rapid traverse X/Z: 60m/30m/min, feed force X/Z: 5kN, ball screw diameter X/Z: 40mm, spindle bearing diameter front: 110mm, speed: 4500rpm, power: 18/28kW, shank diameter: 40mm, power of driven tools: 12kW, speed: 6000rpm. Machine dimensions X/Y/Z: approx. 2700mm/2100mm/2400mm, weight: approx. 7000kg, switch-on time: 50416h, automatic time: 9016h. Documentation available. On-site inspection is possible. Godpfx Apjvva Hkeweka

Condition: ready for operation (used), Year of construction: 1996, Make: SPINNER Type of machine: TC 65 Year of manufacture: 1996 Control system: Siemens 820 T Machine's weight: 4,5 t Tool holder: VDI 20 x-travel: 200mm z-travel: 500mm Gksdpsxg Td Hofx Apwja Speed range: 4000 1/min Overall dimensions: 1,7 x 2,2 x 1,7 m Tool turret - slots: 16 Pl. C-axis: 0,001 Grad Spindle opening: 65 mm

Year of construction: 2004, condition: ready for operation (used), A total of three EMAG vertical turning machines are available. Chuck diameter: 200mm, max. swing diameter: 200mm, travel X/Z: 200mm/400mm, speed: 7500rpm, tool stations: 12. Machine dimensions X/Y/Z: approx. 2450mm/1900mm/2300mm, weight: approx. 5500kg, control: Fanuc. Including extraction system and chip conveyor. Documentation available. An on-site inspection is possible. Gsdoygmdbepfx Apwjka