Used Continuous Furnace for sale (6,502)

Condition: used, -Fuel delivery system -Biomass combustion system -Hot water boiler -Ash removal system -Flue gases primary cleaning system -Stairs and service platforms -Draft fan - Automatic control system -Chimney -Circulation system and water treatment Main parameters and guarantee value are calculated according to fuel parameters: -Moisture 60-65 % -Ash till 8 % - Calorific value 7990 kJ/kg and 1907 kcal/kg Main parameters of the furnace 6000 K: Bledjwfpwpspfx Abpjp - Maximal designed thermal output – 6.5 Mw - Maximum continuous rate – 6 MW - Furnace regulation range 20% - 100% - Volume of furnace- 31.6 m3 - Volume of combustion chamber – 24m3 - Grates area 12 m2 - Grates designed thermal load – 500 Kw/m2 - Combustion chamber designed thermal load – 250 Kw/m3 - Maximum temperature in the combustion chamber - 900°C The following kinds of biomass are accepted for combustion in the furnace: - wood chips – 100% - forest wood residues- 100% - saw dust – 100% (G15) - chunk peat – 100% - bark – 100%

Year of construction: 2017, condition: good (used), functionality: fully functional, Furnace Housing Dimensions Blsdpfx Aexcybksbpep External dimensions: - approx. 3,800 x 4,300 x 2,200 mm Internal (usable) furnace dimensions: - approx. 2,440 x 1,400 x 1,200 mm Batch Load weight: - 9 boxes (net weight 50 kg/each) - approx. 250 kg material per box - stack arrangement 3x3 Performance Data - 1 gas recuperator burner - 160 kW rated heating capacity - Max. allowable chamber furnace temperature 720°C - Max. allowable post-combustion temperature 1,020°C - 1 temperature control zone Temperature Control Range - Chamber furnace 480°C – 700°C - Post-combustion 850°C – 1,000°C Supply Media - Natural gas L or H - Gas inlet pressure 80 mbar - Voltage 400 V - Frequency 50 Hz - Connected load 8 kVA - Compressed air 6 bar, dry, oil-free Material: e.g. brass or bronze

Condition: new, Year of construction: 2026, operating hours: 20 h, functionality: fully functional, machine/vehicle number: RR400FS, area performance: 1,350 m²/h, overall weight: 80 kg, power: 0.3 kW (0.41 HP), battery voltage: 24 V, sweeping width: 350 mm, SCHORR Battery-Powered Scrubber-Dryer RR400FS, Single-Disc Machine With the RR400FS, you can complete wet cleaning and drying in a single pass. The 350 mm wide main brush loosens dirt and removes stubborn residues, while a metered amount of fresh water with cleaning agent is applied. Immediately behind it, the integrated vacuum system sucks up the dirty water. The RR400FS relies on robust and reliable technology without unnecessary frills. It is powered entirely by electricity via a 24V battery system with 32 Ah, which enables approximately 1.5 hours of continuous operation. It can be conveniently charged with the included charger at a standard power outlet. SCHORR Scrubber-Dryer RR400FS – Discover the advantages: ✓ Compact battery-powered scrubber-dryer for small to medium-sized hard floor areas ✓ Cleaning performance of up to 1,350 m²/h ✓ 350 mm main brush, scrubs and vacuums in one pass ✓ Floor is immediately walkable thanks to the integrated vacuum system ✓ 7-liter fresh water and 12-liter dirty water tank, designed to prevent overflow ✓ Fully electric with 24V/32Ah, up to approximately 1.5 hours continuously ✓ Charger included, charges at a standard power outlet ✓ Well-supported: directly from the manufacturer, large spare parts inventory & workshop service Technical data Manufacturer (abbreviation): SCHORR Manufacturer's type designation: RR400FS Model: Electric Scrubber-Dryer Drive: Electric (battery) Weight including battery: 80 kg Tires: PU (non-slip) Wheels, number: 2 Overall length: 900 mm Overall width: 580 mm Overall height: 700 mm Fresh water tank volume: 7 l Dirty water tank volume: 12 l Main brush diameter: 350 mm Area performance: up to 1,350 m²/h Vacuum motor power: 300 W Brush motor power: 310 W Battery voltage/capacity: 24V / 32Ah Operating time: approx. 1.5 hours Charger: Included *Further technical data is available upon request. The scrubber-dryer is designed to be user-friendly and offers an intuitive interface that is easy to understand even for inexperienced users. With its ergonomic design and flexible steering, it enables effortless navigation through narrow spaces, ensuring efficient cleaning with minimal effort. The dirty water tank holds 12 liters, more than the 7-liter fresh water tank. This ensures that no more water is ever taken up than is dispensed at the front. The tank will also not overflow, even if foam forms. Once the work is done, drain the dirty water in a controlled manner, and the compact machine can be quickly stored. Of course, we usually have all the spare parts in stock and can deliver them quickly if you should encounter any problems. If you require technical support, we have the necessary technical expertise and can also carry out repairs in our in-house workshop. Blsdpfszh Hunex Abpsp Would you prefer to finance or lease the device? No problem! We also offer attractive options for this. Just contact us, and we will advise you on the various possibilities. We look forward to your inquiry! We at SCHORR are happy to answer any questions you may have about our scrubber-dryer. You can reach our competent team by telephone or email. We look forward to hearing from you and assisting you with your consultation.

Condition: used, Manufacturer: Ernens Bljdpfxex Rz Rls Abpsp Materials: Stainless steel. Nature of the cleaning fluid: liquid / water – Capacity: example with sultanas 600 to 800 kg/h – Feeding belt: 350 cm x 1500 mm – 2 compartment bowl 600 x 900 x 600 mm including : 1 inclined screw for product recovery d.150 mm 1 screw + horizontal draining drum d.300 mm – Heating by external recycling of the fluid

Year of construction: 2026, operating hours: 5 h, condition: new, functionality: fully functional, NOMA NOWICKI MHM-21/84 F is a brine injector designed for the uniform injection of fish and seafood, both boned and unboned, and – after a quick needle change – any other boned or unboned products, such as poultry. Manufactured in 2026, the machine features 21 needle sockets (84 quadruple needles), steel needles operating at a brine pressure of up to 3 bar, microprocessor control with a color touchscreen, and an AISI 316 stainless steel construction in food-contact areas. Replacement parts are included. Key Advantages of the NOMA NOWICKI MHM-21/84 F Brine Injector The machine ensures even distribution of brine in delicate products, such as fish fillets and seafood, and, after changing the needles, is suitable for injecting poultry and other products, whether bone-in or boneless. Smooth adjustment of pressure and head speed, 2-mm-diameter needles, and three-level pressure adjustment allow the injection process to be tailored to various raw materials and recipes. Manufacturer: NOMA (NOWICKI MACHINERY) Machine type: brine injector Model: MHM-21/84 F Serial number: 01126803 Year of manufacture: 2026 Power supply: 3 x 400 V, 50 Hz Marking: CE, manufactured in the EU Installed power: 2.4 kW, maximum current 12 A Pump power: 1.5 kW Construction: AISI 316 stainless steel in food-contact areas, AISI 304 in other components; designed for use in the fishing industry Number of needle sockets: 21 Maximum number of needles: up to 84 (quad needles) for fish and seafood, or 42 for poultry Needle diameter: 2 mm Head: easily replaceable, with quadruple needles as standard, top-side needle loading Head drive: top-mounted, NORD gearbox with frequency converter, stepless speed control Number of head strokes: 21 – 44 strokes/min Maximum head stroke height: 110 mm Maximum product height before injection: approx. 90 mm (up to 110 mm after injection) Removal clamp: adjustable to 3 heights, prevents over-injection Conveyor: easy-to-clean plastic belt, 325 mm wide Conveyor feed per head stroke: adjustable, 16; 35; 75 mm/cycle Brine pressure: continuously adjustable from 0.5 to 3.0 bar (in 0.1 bar increments), up to 3 bar as standard Brine pump: centrifugal, high-efficiency, stainless steel, controlled by a variable-frequency drive Filtration: multi-stage, easy to clean, with an additional tubular filter for improved brine purification Brine tank: stainless steel, 80 L, with brine mixing (preparation) and drainage Injection rate for a single pass (salmon): up to 12% Controls: microprocessor-based HMI, MITSUBISHI color touchscreen, MITSUBISHI PLC, variable-frequency drives on the gearbox and brine pump Throughput (approximate, for 1 pass): Herring fillets: injection rate approx. 10%, approx. 200 kg/h Salmon fillets: injection rate 8 – 12%, approx. 250 kg/h Poultry fillets: injection rate 25 – 30%, approx. 500 kg/h Bedpfj Aggiqex Abpolp Chicken drumsticks: injection rate 20%, approx. 500 kg/h Chicken necks and wings: injection rate 12%, approx. 400 kg/h

Condition: used, Year of construction: 2018, Used Machine Year of Manufacture: 2018 Special Feature: Machine with a gluing height of up to 100 mm! Condition: Factory-inspected by Lange Maschinenbau Features and Technical Specifications: - Machine table with 13 rollers for improved workpiece guidance - Edge feed, synchronized with the belt feed - Edge thickness adjustable via digital counter - Pneumatic roller separation with blade (for cutable edges) - Three pressure rollers - Belt feed: - 0.25 kW - Approx. 1,250 mm long - Approx. 6.0 m/min - 50 mm wide toothed belt with a thick, workpiece-protective rubber covering - Digital counter for height adjustment - Direct glue application to the workpiece: Leak-proof glue tank with glue supply from below and fast heat-up time after machine shutdown - Flush trimming unit: - for the front and rear edges of the workpiece - Automatic sensing of the workpiece - Pneumatic trimming with a blade for cut-ready edges - Flush milling unit - With vertical sensing and horizontal guidance - Reproducible adjustment via digital counters - 2 powerful 0.4 kW high-frequency motors - Continuously adjustable from 4,000 to 18,000 rpm - Milling cutter: 70 mm, Z4, radius 2 mm/15° - Central exhaust port: 100 mm - 2 chip extraction hoods with 60 mm hose - Automatic height adjustment of the upper router bit via the belt feed - Continuous workpiece support, approx. 1,800 mm long - Workpiece support rail, extendable by approx. 300 mm - Rotatable film plate: 800 mm - Workpiece width: min. approx. 80 mm - Workpiece thickness: 10–100 mm Bljdpfx Abezk Nmrjpop - Workpiece length: min. approx. 220 mm - Edge thickness: 0.4–2.0 mm - Roller cutting: max. 1.0 × 55 mm, 2 × 45 mm - Glue pot heating power: 2.7 kW - Heat-up time: approx. 10 minutes - Working height: approx. 880 mm - Electrical connection: 400 V, 50 Hz, 3-phase N - Total power consumption: 3.8 kW - Pneumatic connection: 6 bar Dimensions (without film tray): approx. 1800 x 700 x 1300 mm Weight: approx. 260 kg

Condition: good (used), Year of construction: 2018, functionality: fully functional, travel distance X-axis: 650 mm, travel distance Y-axis: 520 mm, travel distance Z-axis: 475 mm, rotational speed (max.): 15,000 rpm, number of slots in tool magazine: 30, DMG MORI DMU 50, 3rd Generation 5-Axis Universal Machining Center Manufacturer: DMG MORI Model: DMU 50, 3rd Generation Year of Manufacture: 2018 Control System: Siemens 840D sl Operate with CELOS Operating Panel: 21.5-inch ERGOline Multi-Touch Technical Data Machining: 5-axis simultaneous machining NC rotary table Travel distances: X-axis: 650 mm Y-axis: 520 mm Z-axis: 475 mm Swivel/Rotary Axes: B-axis: -35° to +110° C-axis: 360° Worktable: Clamping area: Ø 630 × 500 mm Maximum table load: 300 kg Main Spindle: speedMASTER motor spindle Spindle speed: 20–15,000 rpm Tool interface: SK40 Spindle power: 21 kW (40% duty cycle) Continuous power: 16 kW (100% duty cycle) Tool Changer: Tool magazine: 30 positions Tool interface: SK40 Feed Rate: Blsdo Agnykopfx Abpop Rapid traverse X/Y/Z: 42 m/min Special Equipment Internal coolant supply (IKZ) with 40 bar Coolant system with 600 liter tank Paper band filter system including cabin roof Chip conveyor with scraper chain Double-stage filter, 25 µm, manually switchable Blow-off air through spindle center, selectable via M-function Renishaw PP60 optical infrared workpiece measuring probe (OMP60) Heidenhain TT160 tool measurement Tool length and diameter measurement Tool breakage detection 3D quickSET for checking and correcting machine kinematics ATC – Application Tuning Cycle Electronic handwheel Flushing gun for chip removal Total spindle hours: approx. 18,600 New spindle replaced in 2021 at approx. 5,800 hours

Condition: new, Year of construction: 2026, Hydraulic winch HAW1700 with electric valve incl. manual operation and radio remote control for mounting on wood splitters, cranes, mini excavators, tractors, forklifts, mowing tracked vehicles, and telescopic loaders, for use in viticulture and horticulture, agriculture, construction, and forestry, as well as many other applications. Equipped with an electric hydraulic valve and radio remote control. The hydraulic winch HAW1700 can simplify many tasks. Maximum rope capacity of 30 m with 6 mm wire rope. Standard equipment includes 20 m of 6 mm wire rope. Bodsfn Tvhspfx Abpelp ⦁ Pull and position firewood for the wood splitter ⦁ Pull logs onto a trailer ⦁ Pull out tree stumps and trees ⦁ As an auxiliary winch on skidders and small excavators ⦁ As a winch for small tractors and narrow-gauge tractors A robust steel construction with the possibility of mounting on both sides (bottom, rear, top) with M12 threads. This allows for flexible use of the winch. Large, double-bearing rope pulley for long wire rope life. The pulling force is 1700 kg as standard. The winch can be installed in various positions. An optional hydraulic brake is available. Depending on the required pulling speeds and forces, we can offer you different options. Please contact us, and we will be happy to advise you. ⦁ Maximum working pressure: 225 bar peak ⦁ Continuous operating pressure: 175 bar ⦁ Displacement: 400 ccm ⦁ Torque at 225 bar: 870 Nm peak ⦁ Torque in continuous operation: 380 Nm ⦁ Maximum pulling force: 1700 kg ⦁ Weight: 49 kg ⦁ Rope speed: 47 m/min at 60 l/min oil flow ⦁ Color: red ⦁ Including hoses from the valve to the motor Dimensions: ⦁ Length: 500 mm ⦁ Length with rope inlet: 570 mm ⦁ Front width: 120 mm ⦁ Rear width: 180 mm ⦁ Bearing width: +30 mm ⦁ Motor width: +200 mm ⦁ Height: 250 mm Included: Radio remote control for the winch. ⦁ Control range: up to 100 m ⦁ Temperature: -35 °C to +80 °C Protection class: IP65

Condition: new, functionality: fully functional, Year of construction: 2026, machine/vehicle number: HAW1700-EV-Funk, rope length: 30,000 mm, rope speed: 47,000 mm/min, Hydraulic winch for wood splitters, cranes, mini excavators, tractors, agricultural vehicles, viticulture, horticulture, and many other applications. The hydraulic attachment winch simplifies many tasks: - Pulling and positioning firewood to the wood splitter - Pulling logs onto trailers - Removing tree stumps and roots - As an attachment winch on forestry cranes and small excavators - As a winch for small tractors and narrow-gauge tractors A robust steel construction with 3-sided mounting options (left, right, rear) and 12 threaded holes offers many possibilities for attaching the winch (threads are cut and painted. They need to be re-cut with a thread tap before use due to the rust protection). A 20 m long and 6 mm thick steel cable is mounted. A large cable pulley ensures a long service life for the steel cable. We mount hydraulic motors from 50 to 630 cc (standard = 400 cc), depending on the speed and pulling force required. Maximum working pressure: 225 bar peak Continuous operating pressure: 175 bar Displacement: 400 cc Torque at 225 bar: 870 Nm peak Torque in continuous operation: 380 Nm Maximum pulling force: 1700 kg Weight: 49 kg Bedpfxjdf Ufpo Abpelp Cable speed: 47 m/min at 60 L/min hydraulic oil Color: red Dimensions: Length: 500 mm Length with swivel: 570 mm Front width: 120 mm Rear width: 180 mm Bearing width: + 30 mm Motor width: + 200 mm Height: 250 mm The winch is available for mounting or welding. This version includes an electric hydraulic valve, remote control, and hoses to the motor. Article number: HAW1700-EV-Funk

Condition: new, Year of construction: 2026, Power: 1.1 kW Drilling capacity in steel / continuous drilling capacity: 30 mm / 25 mm diameter Speed range: continuously variable, 120 - 3000 min⁻¹ Spindle mount: MK-4 Drilling stroke: 120 mm Spindle overhang: 254 mm Bledpfozhm D Aex Abpop Table size: 475 mm x 425 mm Tilting/rotating of the drilling table: 45° to the left / 360° Column diameter: 80 mm Quick-change toolholder: 1 - 16 mm Weight: 132 kg

Condition: new, Year of construction: 2026, Working width: 530 mm Planing cylinder: Tersa Number of knives: 4 Jointer table length: 2300 mm Adjustable angle of the jointer fence: yes Raising of the jointer table: electric Maximum stock removal thickness (thickness planer): 250 mm Height adjustment of the thickness table: electric Display of the planing thickness: digital Feed rate: 5 / 7 / 9 / 12 m/min Infeed roller: steel Outfeed roller: rubber Pressure bar: continuous Blodpfxjzqyw Uo Abpsp Table rollers: no Motor power: 7.5 kW Motor brake: yes, automatic Dust extraction connection: 140 mm Machine length: 2300 mm Machine width: 990 mm Weight: 750

Year of construction: 2022, condition: new, Motor power: 1.1 kW / 230 V Blodpfx Asgulr Ajbpop Cutting area: 100 mm x 145 mm Feed: continuously adjustable Saw blade speed: 22 / 31 / 55 m/min Saw blade dimensions: 1638 x 13 x 0.65 mm Cutting angle: -45° to 60° Dimensions: 1085 mm x 498 mm x 978 mm Weight: 78 kg

Condition: excellent (used), Year of construction: 2019, BEAM MODULO 400 Year Mfg 2019 Siemens Control Bjdpfxszvlhpj Abpjlp Build Volume: Approximately 650 × 400 × 400 mm (or roughly 600 × 400 × 400 mm operational) with continuous 5-axis motion kinematics Laser Source: Ytterbium fiber laser options ranging from 500 W up to 2 kW Deposition Heads/Nozzles: Supports an automatic tool changer to swap between different heads (e.g., the 10Vx for fine precision down to 0.1 mm and the 24Vx for higher deposition rates) without stopping production Powder Delivery: Equipped with a vibrating multi-hopper powder feeder system capable of managing up to 4 or 5 separate material feed options

Condition: used, Year of construction: 2025, COLOMBO R. Discontinuous sandwich panel production line Complete PUR sandwich panel production line for manufacturing panels up to 8 meters in length. Fully automated and equipped with a heated press, high-pressure foaming machine, and integrated roll forming system. A high-performance industrial solution for producing roof and wall sandwich panels in compliance with European standards. Production specifications - Production of sandwich panels up to 8 meters long. - Panel thickness: 40 - 100 mm. - Pre-painted steel thickness: 0.40–0.80 mm. - Manufacturing of roof and wall sandwich panels. - Capability to produce tile-effect sandwich panels. - Automatic cut-to-length system. - Automated machine settings. - Electrical components from leading brands: Siemens, Rexroth, Schneider Electric, Omron, and SMC. Line configuration - 4-platen heated press. - Maximum panel length: 8 meters. - Production of polyurethane (PUR) insulated sandwich panels. - ULTRAMIX 100 high-pressure foaming machine with 1:1 mixing ratio and self-cleaning mixing head. - Complete roll forming line for steel facings. - Two roll forming lines for manufacturing different panel profiles. - 7-ton hydraulic decoilers. - Automatic hydraulic cutting system. - PLC control system with touchscreen interface. - Automatic control of panel lengths and production quantities. - Fully automatic dosing of foam components. - CE-compliant installation with integrated safety systems. Included - Complete production line. - High-pressure foaming machine. Bsdpfx Abezrhtmopjlp - Heated press. - Roll forming equipment. - Outfeed tables. - Electrical control cabinet. - PLC control system. - Technical documentation included. Panel length: Up to 8 meters Panel thickness: 40 - 100 mm Pre-painted steel thickness: 0.40 – 0.80 mm Panel types: Roof and wall sandwich panels, capability to produce tile-effect sandwich panels Control system: PLC control with touchscreen interface and automatic settings Foaming machine: ULTRAMIX 100 high-pressure foaming machine (1:1 mixing ratio) Press type: 4-platen heated press

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: PSP-26001, pressure: 0.4 bar, total width: 500 mm, total length: 500 mm, total height: 1,950 mm, overall weight: 75 kg, warranty duration: 3 months, manhole location: bottom, empty load weight: 50 kg, input voltage: 230 V, machine base height: 250 mm, type of input current: AC, volume flow: 0.15 m³/h, Equipment: documentation/manual, type plate available, Continuous-flow pasteurizer (throughput volumes depend on operating time, hygiene, and precision): • Performance and investment suitable for small on-farm dairies as well as local processing workshops: 700 liters in 6 hours. • Base of 50x50cm, 200cm high. Removable side guards. • Gravity-fed milk flow: provides stable flow and smooth regulation. The milk or juice is fed or pumped into an intermediate container at a height of 4 meters and flows from there to the bottling station. Bjdpfszg Dlbox Abpjlp • A pump supplies this container at the elevated height. It also ensures effective cleaning through intense detergent circulation. • Manual control by the operator at the bottling station with alarms for "too fast" filling (incomplete pasteurization) or "too slow" filling (product overheated): the operator can then slow down or speed up the bottling process. • No contact with air: Hygienic and precise processing! • Only 2.2 kW of electricity to pasteurize more than 120 liters per hour (700 liters per day). Automatic control of the water bath temperature with a setpoint between 70 and 92°C (from thermization at 65°C to "cooking" for yogurt at 85°C). • The basic pasteurizer consists of: 1. a heat exchanger between the incoming (cold) milk (or juice) and the pasteurized milk (or juice) (72°C), 2. a heating tank (2.2kW, temperature adjustable to 5°C above the pasteurization setpoint) in which a coil is immersed, through which the liquid exiting the heat exchanger circulates, 3. a well-insulated holding tube where the milk/juice is kept for 15 seconds at the pasteurization temperature, 4. a temperature controller to illuminate a light if the liquid is too cold and another if the liquid is too hot, 5. a tube leading to the elevated inlet container, tubes connecting all components, one or two tubes with a Mohr clamp for manual filling of bottles (optional bottling unit) or jars (one at a time), 6. a drain valve at the lowest point (after pasteurization and holding, and before returning to the heat exchanger): allows the circuit to be emptied down to the last drop of pasteurized product. 2. Transfer pump with controls: • Prevents the need to transport milk or juice by pumping it from where it is located (tank on a trailer, refrigerated tank, receiving tank, container, etc.) to the inlet tank of the pasteurizer on the upper floor. • Automatic pause when the inlet tank of the pasteurizer is full (conductivity probes). Automatic restart when the level drops. • Performance between 8 and 25 liters per minute (depending on the height difference). • Also ensures powerful cleaning of the entire pasteurization circuit. • Food-grade design and materials. • Electrical consumption of 400 W. • Option: 200µm basket filter for wort, juices, and herbal extracts with moderate alcohol content. 3. Option: "Manual gravity-fed bottling unit with automatic stop, 180 liters per hour": twice the throughput with less work!

Year of construction: 2018, condition: new, functionality: fully functional, machine/vehicle number: 36817, Vulcan 24" OD × 20" Sonic Loop Turret Coiler Winder with Automatic Cut & Transfer – BRAND NEW The Sonic Loop Turret Coiler is a two-spindle turret-type winding system designed for continuous, virtually tensionless coiling of extruded profiles. The extrudate is fed to the coiler through an ultrasonic sensing dancer system, which monitors the position of the extrudate loop and automatically adjusts the speed of the servo-driven winding spindles. This provides smooth, controlled winding while minimizing tension on the extruded product. The unit is equipped with an automatic cut-and-transfer system, allowing the product to be rapidly transferred from the full reel to a new empty reel without interrupting the coiling process. Technical Specifications Winder Type: Two-spindle turret coiler Maximum Reel OD: 24" Reel Width: 20" Centerline Height: 42" Line Speed: Up to 200 FPM on 8" diameter core Drive: Servo-driven spindles Loop Control: Ultrasonic sensing dancer Cut & Transfer: Automatic Electrical Supply: 380 VAC, 50/60 Hz, 3-phase Condition: Brand New / Never Used Bsdpfx Aozz N Evjbpolp The equipment was manufactured and underwent final assembly/testing at the Vulcan facility before shipment. It has never been placed into production and is currently stored and ready for shipment. Original documentation is available where applicable. Available for immediate sale. Inspection and shipping arrangements can be coordinated with the buyer.

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, machine/vehicle number: 31.064-R-11/2022, overall weight: 1,200 kg, heating capacity: 49 kW (66.62 HP), total height: 2,090 mm, total length: 2,270 mm, total width: 780 mm, Equipment: documentation/manual, Offering a used Optimal E Gr.II-S hot air furnace. Bsdpfx Abszy R Rdopolp Sale due to workshop restructuring. Heating capacity, special version: 49 kW. Cleaning side on the right – with automatic control. - Complies with 1st Federal Immission Control Ordinance (BlmSchV) – Stage 2!!! - Suitable for rooms according to DIN, up to 700-1250 cubic meters. - According to the Federal Immission Control Ordinance (BlmSchV), approved for particleboard or coated wood-based materials (only in woodworking or wood processing companies). Fine sawdust or dust of any kind is not suitable – risk of deflagration!!! - Furnace consumption: approx. 15 - 25 kg/h. - Tested in accordance with DIN EN 13240: 2005-10 (continuous operation), DIN EN 13229:2005-10, DIN EN 303-5:2012-10. Sale does not include the stainless steel chimney.

Condition: excellent (used), Year of construction: 2018, 544 USED Wachtel Compact 1.8F rotary trolley oven. Oven for 60x80 or 58x78 baking trays. Blsdpfx Asz Atygobpep EQUIPMENT: - gas burner - 2 baking trolleys 58x78 TECHNICAL DATA: - year of production: 2018 - thermal power: 81kW The price is a net price. Our languages: ENGLISH, FRENCH, GERMAN, RUSSIAN, UKRAINIAN. ..... bakery oven, bakery ovens, bakery machine, bakery machines, bakery equipment, bakery equipments, bakery device, bakery devices

Condition: new, Year of construction: 2026, NEW ON THE POLISH MARKET 230 V Screw Air Compressor THE SET INCLUDES: - CORMAK AIR30 SCREW AIR COMPRESSOR. - 150 L HORIZONTAL COMPRESSED AIR RECEIVER TANK (with wheels). CORMAK AIR30 Screw Air Compressor – Compact Power for Your Business Are you looking for an efficient and reliable air compressor suitable for smaller workshops, service centers, or hobby applications, while also requiring a single-phase power supply? The CORMAK AIR30 screw air compressor is the perfect solution. With a motor power of 3.0 kW and an impressive actual air delivery of up to 400 L/min, it provides a continuous supply of compressed air essential for the efficient operation of impact wrenches, air blow guns, and spray painting tools. Powered by 230 V / 50 Hz, this model has been designed for continuous operation, making it an excellent choice for demanding applications such as small workshops, tire service centers, and craft businesses. Investing in a CORMAK screw air compressor is a step towards significantly improving working comfort – say goodbye to noisy piston compressors and enjoy quieter, more stable operation. The CORMAK AIR30 features a reliable and robust direct-drive system that eliminates vibrations and the need for belt drive adjustments. This proven solution ensures stable performance and a long service life by transferring power directly from the motor to the screw compression unit. The maximum operating pressure generated by this screw air compressor is 10 bar. Full control over the machine's operating parameters is provided by an intuitive MAM series electronic control panel, giving you access to essential compressor information and improving flexibility and control over your operations. ✅ Pressure: up to 10 bar | ✅ Air Delivery: up to 400 L/min | ✅ Power: 3.0 kW | ✅ Power Supply: 230 V Technical Specifications Parameter Specification Motor Power 3.0 kW / 4 HP Voltage 230 V / 50 Hz Air Delivery at 0–6 bar Average 400 L/min Bedpfx Abo Agu I Tjpelp Air Delivery at 6 bar 390 L/min Air Delivery at 8 bar 380 L/min Air Delivery at 10 bar 380 L/min Air Outlet Connection Diameter (G) 1/2" Dimensions 1110 × 650 × 1320 mm Weight 145 kg

Condition: good (used), Year of construction: 1988, Ref. -No.: 10396 Manufacturer: KELLENBERGER Type: 600 U - Nr. 40 Year of construction: 1988 Type of control: Konventionell Control: N/A Storage location: Halberstadt Country of origin: Switzerland Distance between center: 600 mm Center height (standard): 125 mm Height of centers by lifting work blocks head and tailstock: 175 - 250 mm Swing diameter with lifting blocks max.: 350 - 500 mm Table swivel / each side: 10 ° Dwell time of the table reversal: 0 - 5 Sec Diameter / width / hole: 250 x 13 x 76 mm Bodo Ahmupspfx Abpslp Speeds of the grinding wheel spindle: 1500/1700/2200/3600 Swiveling grinding wheel head: 360 ° Cross movement of the grinding wheel head: 285 mm Quickly pulling the wheel head back and forth: 40 mm Intermittent injection for each reversal of the table: 0,001 - 0,03 mm / dia Micro-corrector of the feed, 1 division of the dial: 0,001 mm / Ø Working speeds continuously adjustable (normal / special): 20-400/10-400 Max. Grinding length: 900 mm

Condition: excellent (used), functionality: fully functional, Year of construction: 2015, operating hours: 4,496 h, load capacity: 4,000 kg, lifting height: 4,050 mm, load center: 600 mm, fuel type: gas, mast type: duplex, construction height: 2,800 mm, motor manufacturer: GM, gearing type: hydrostat, fork carriage width: 3,100 mm, fork length: 1,300 mm, fork width: 150 mm, fork thickness: 50 mm, tire condition: 100 %, front tire type: cushion tires (black), front tire size: 200 / 50 - 10, rear tire size: 27 X 10 - 12, overall weight: 10,200 kg, empty load weight: 6,200 kg, total height: 2,450 mm, total length: 2,300 mm, total width: 2,250 mm, color: green, Equipment: 3rd hydraulic function, 4th hydraulic function, CE marking, all wheel drive, cabin, fork extension, front guard, head guard, hydraulic fork positioner, lighting, pallet forks, # COMBILIFT C4000 | DUPLEX 4050 MM | WIDE FORK POSITIONER 3100 MM | FULL CABIN | READY TO WORK 🔧 FULLY SERVICED MACHINE | 🛡️ WARRANTY | 🌍 DELIVERY ACROSS EUROPE AND WORLDWIDE If you are looking for a forklift that will start generating value from day one instead of creating additional service costs, this machine is the right choice for you. We are offering a proven and fully prepared COMBILIFT C4000 multidirectional forklift. The machine has undergone a complete technical inspection, comprehensive servicing, and detailed testing. It is ready for immediate operation in a production facility, warehouse, or logistics centre. ### ⭐ KEY BENEFITS 🔧 Complete service carried out before sale 🛡️ Start-up warranty 🛞 Brand new superelastic tires ✨ Very good technical and visual condition ✅ Ready to work without additional investment 🎥 Live online video presentation available 🚛 Direct delivery to the customer available ### 📋 TECHNICAL SPECIFICATION 🏭 Manufacturer: COMBILIFT 🚜 Model: C4000 📅 Year of manufacture: 12/2015 🏋️ Load capacity: 4000 kg ⛽ Power: LPG ⏱️ Operating hours: 4496 h ⬆️ Mast: DUPLEX 📏 Lifting height: 4050 mm ↔️ Wide hydraulic fork positioner: 3100 mm 🍴 Fork length: 1300 mm 🚪 Cabin: Full and heated ⚖️ Machine weight: 6200 kg ### 📐 DIMENSIONS 📏 Overall height: 2450 mm 📏 Length: 2300 mm 📏 Width: 2250 mm 📏 Mast closed height: 2800 mm ### 🛞 TIRES 🔹 Front: 200/50-10 superelastic 🔹 Rear: 27 x 10-12 superelastic ✅ Tire condition: 100 percent brand new ### ⚙️ EQUIPMENT ↔️ Wide hydraulic fork positioner 🔥 Full heated cabin 💡 Work lights 🚨 Warning beacon ### 🏗️ IDEAL FOR 🪵 Timber industry 🏭 Steel mills and steel stockholders 🔩 Steel construction manufacturers 📦 Handling pipes, profiles and long materials 🏢 Indoor and outdoor operation ### ⭐ WHY FT LOGISTICS When purchasing from FT LOGISTICS, you are buying from a company specializing in forklifts, sideloaders, multidirectional forklifts, and warehouse equipment. 🔧 Every machine undergoes a comprehensive technical inspection, complete service, and detailed testing before being released to the customer. 🚜 We have more than 100 machines available from stock and supply equipment to customers throughout Europe, South America, Africa, Asia, and the Middle East. ### 🤝 WE PROVIDE 🔧 Complete service before sale Bjdpe Ag Nbhofx Abpolp 🛡️ Warranty 👨‍🔧 Professional technical advice 💶 Leasing and financing 🚛 Transport organization 🌍 Export services and customs documentation 🤝 After-sales support Hundreds of customers across Europe have trusted our machines and continue to return to us for further purchases. 🎥 We can arrange a live online presentation of the machine, provide additional photos and videos, and prepare an individual transport quotation directly to your company. ### FT LOGISTICS 🚜 WE DELIVER MACHINES READY TO WORK.

Year of construction: 2014, operating hours: 40,000 h, condition: used, functionality: fully functional, belt width: 560 mm, number of shelf rows: 8, machine/vehicle number: B6, High-Capacity Industrial Ambient Spiral Cooling Conveyor Tower Heavy-duty 8*2 -tier ambient spiral cooling tower engineered for food production and industrial bakery applications. Built entirely with a high-grade stainless steel frame and structure, ideal for washdown environments and strict hygiene standards. Key Technical Specifications: Tier Count: 16 continuous spiral tiers / turns. Belt Width: 560 mm food-grade blue open-mesh modular belt for maximum air circulation and product stability. Drive System: Heavy-duty Brevini / Rossi industrial planetary gear drive motor assembly. Control System: Freestanding stainless steel electrical control cabinet featuring a Siemens SIMATIC HMI touch display panel, integrated VFD variable speed frequency drives, and emergency safety stops. Bljdpfxez E A Rkj Abpsp Applications: Suitable for ambient cooling of baked goods, confectionery, wafers, packaged products, and snack items prior to packaging. Condition: Used, Dismantled ،fully functional, clean, and in very good working condition.

Condition: excellent (used), functionality: fully functional, Year of construction: 2023, operating hours: 2,245 h, load capacity: 2,500 kg, lifting height: 4,900 mm, free lift: 1,380 mm, load center: 600 mm, fuel type: gas, mast type: triplex, construction height: 2,250 mm, motor manufacturer: KUBOTA, gearing type: hydrostat, fork carriage width: 1,400 mm, fork length: 1,200 mm, fork width: 120 mm, fork thickness: 50 mm, tire condition: 100 %, front tire type: cushion tires (black), front tire size: 16 x 7 x 10½, rear tire type: cushion tires (black), rear tire size: 23 x 10 x 16, overall weight: 8,800 kg, empty load weight: 6,300 kg, total height: 2,250 mm, total length: 1,550 mm, total width: 1,500 mm, color: green, Equipment: CE marking, all wheel drive, cabin, head guard, lighting, pallet forks, sideshift, # 🚜 COMBILIFT CB3000 | LPG | 4900 MM | FORK POSITIONER | SIDE SHIFT | FULL CABIN | READY FOR WORK ✅ ## 🔧 FULLY SERVICED MACHINE | 🛡️ WARRANTY | 🌍 WORLDWIDE DELIVERY AVAILABLE If you are looking for a forklift that will generate value from day one instead of incurring maintenance costs, this machine is the perfect solution. We offer a modern and fully prepared COMBILIFT CB3000 multidirectional forklift, professionally serviced, thoroughly inspected, and ready for immediate operation in warehouses, production facilities, timber yards, steel service centers, and logistics environments. --- ## ⭐ Key Benefits ✅ Fully serviced prior to sale ✅ Start-up warranty included ✅ Excellent technical and cosmetic condition ✅ Low operating hours – only 2,245 h ✅ Ready for immediate operation with no additional investment required ✅ Live online demonstration available ✅ Direct delivery to your facility available --- # 📋 TECHNICAL DATA 🏭 Manufacturer: COMBILIFT 🚜 Model: CB3000 📅 Year of Manufacture: 2023 🔢 Serial Number: 73868 ⚖️ Capacity: 2,500 kg 📏 Load Center: 600 mm ⛽ Engine: Kubota LPG Gas ⚙️ Engine Power: 42 kW 🕒 Operating Hours: 2,245 h ⬆️ Lift Height: 4,900 mm 🏋️ Machine Weight: 6,300 kg --- # 📐 DIMENSIONS 📏 Overall Height: 2,250 mm 📏 Construction Height: 2,250 mm 📏 Overall Length: 1,550 mm 📏 Overall Width: 1,550 mm 📏 Fork Positioner Width: 1,400 mm --- Bjdj Ahggpjpfx Abpelp # 🔩 FORKS 📌 Fork Length: 1,200 mm 📌 Fork Section: 120 x 50 mm --- # 🛞 TIRES Front: 16 x 7 x 10½ Rear: 23 x 10 x 16 --- # 🛠️ EQUIPMENT ✅ Full enclosed cabin ✅ Heating system ✅ Radio ✅ Hydraulic fork positioner ✅ Side shift ✅ Working lights ✅ Kubota LPG engine ✅ Multidirectional steering system ✅ Operator comfort package --- # 🏭 IDEAL FOR 🌲 Timber and wood processing industry 🪑 Furniture manufacturers 🏗️ Steel mills and steel service centers 🔩 Aluminium and PVC profile handling 📦 Handling of long loads ↔️ Narrow aisle operations 🏢 Indoor and outdoor applications --- # 🤝 WHY CHOOSE FT LOGISTICS? When purchasing from FT LOGISTICS, you are working with a company specialized exclusively in: ✅ Sideloaders ✅ Multidirectional forklifts ✅ Long-load handling equipment ✅ Specialist material handling solutions Every machine undergoes a comprehensive technical inspection, full service, and operational testing before delivery. 🌍 With more than 100 machines available from stock, we supply customers throughout Europe, South America, Africa, Asia, and the Middle East. --- # 🚀 WE PROVIDE 🔧 Full service before delivery 🛡️ Warranty 👨‍🔧 Professional technical support 💰 Leasing and financing assistance 🚛 Transport organization 📄 Export documentation and customs support 🔩 After-sales service --- Hundreds of customers across Europe trust our equipment and continue to return for future purchases. 📹 We can arrange a live online demonstration. 📸 Additional photos and videos available upon request. 🚛 Customized transport quotation available for any destination worldwide. --- # FT LOGISTICS ### 🚜 We Deliver Machines Ready for Work.

Condition: used, Year of construction: 2018, Bolting welding power source Manufacturer: Soyer Type: BMH 22i (inverter power source) Year of manufacture: 2018 Maximum welding current: 2,000 A Welding cycle: Ø6/30, Ø22/3 bolts/min. Open-circuit voltage: 75 V Type of protection/cooling method: IP 21 / F Connection: 3-phase 400 V / 63 A, 50/60 Hz Electrical continuous current: 2 A / phase Bjdpfx Ao Ahhf Uebpolp Electrical continuous power: 1,400 VA Electrical peak current: 180 A / phase Included: Welding gun Ground cable 41126ä

Condition: new, Year of construction: 2026, functionality: fully functional, workpiece weight (max.): 300 kg, travel distance X-axis: 320 mm, travel distance Y-axis: 400 mm, travel distance Z-axis: 260 mm, total height: 1,800 mm, total length: 1,650 mm, total width: 1,150 mm, wire diameter (max.): 18 mm, workpiece height (max.): 400 mm, workpiece width (max.): 580 mm, workpiece length (max.): 580 mm, type of input current: three-phase, table width: 600 mm, overall weight: 1,700 kg, table length: 600 mm, table height: 380 mm, empty load weight: 1,400 kg, warranty duration: 12 months, table load: 300 kg, input voltage: 400 V, quill travel distance: 80 mm, quill diameter: 6 mm, quill stroke: 80 mm, stroke length: 80 mm, tank capacity: 110 l, cutting speed: 600 mm/min, input current: 6 A, positioning accuracy: 2 mm, Equipment: documentation/manual, Digima DK7732 CNC EDM Wire Cut Machine – 320 × 400 mm The Digima DK7732 is a compact CNC EDM wire cutting machine designed for precise machining of small and medium-sized metal components. It is suitable for tool rooms, mould and die production, maintenance workshops, precision engineering companies, as well as single-piece and batch production. The machine provides an X/Y working travel of 320 × 400 mm, a 380 × 600 mm worktable, a maximum workpiece height of 400 mm, and a maximum permitted workpiece weight of 300 kg. Its rigid construction and machine weight of 1,400 kg help reduce vibration and support stable, repeatable machining. EDM wire cutting technology allows the machine to produce accurate contours, narrow slots, holes and complex shapes in electrically conductive materials, including hardened metals that may be difficult to process using conventional cutting tools. Real photos in the gallery - machine comes new Main Advantages CNC-controlled EDM wire cutting machine Compact design suitable for smaller production areas X/Y worktable travel of 320 × 400 mm Large 380 × 600 mm worktable Max. workpiece height of 400mm Max. workpiece weight of 300kg Stable 1,400kg machine construction Suitable for complex contours and precision components Designed for mould, die and tool production Suitable for single-piece and serial production Low operating energy requirements Reduced molybdenum wire consumption Suitable for long, continuous machining cycles Technical Specification Parameter Specification Brand Digima Model DK7732 Machine type CNC EDM wire cut machine Condition New Worktable dimensions 380 × 600 mm X/Y worktable travel 320 × 400 mm Maximum workpiece height 400 mm Taper capability 6° / 80 mm Maximum workpiece weight 300 kg Bjdpfx Absznttdepslp Machine net weight 1,400 kg Machine dimensions 1,650 × 1,150 × 1,800 mm Control system CNC/MNC Movement method Linear control Control method Open-loop control Processing accuracy 0.01–0.02 mm Molybdenum wire diameter Ø0.13–Ø0.18 mm Maximum wire speed 600 m/min Maximum cutting speed 200 mm²/min Best surface roughness ≤ Ra 0.8 µm Maximum working current 6 A Rated power 2 kVA Water tank capacity 110 litres Water filtration accuracy 0.005 mm Application Electrically conductive metal materials With a stated processing accuracy of 0.01–0.02 mm, cutting speeds of up to 200 mm²/min, and a best surface finish of up to Ra 0.8 µm, the DK7732 is suitable for applications where dimensional accuracy and surface quality are important. Stable and Economical Operation The DK7732 is designed for stable processing, relatively fine surface quality, low energy consumption and reduced molybdenum wire wear. It is particularly suitable for users who prioritise economical operation and long continuous machining cycles rather than exceptionally high cutting productivity. Delivery and Availability Availability: available / one left in stock Estimated delivery time: approximately 90 working days, only one we have left in stock Transport and installation conditions: to be agreed individually Availability and delivery information should be confirmed before placing the final order. The Digima DK7732 combines a practical working range, rigid construction, high workpiece capacity and economical EDM technology. It is a suitable solution for companies looking for a compact wire cutting machine for accurate machining of moulds, dies, tools and specialised metal components.