Used Corrugator for sale (316)

Condition: ready for operation (used), Year of construction: 1989, MACHINE: BOBST Domino 85-M Manufacturer: BOBST SA Model number: Domino 85-M Machine type: Folder-gluer Year manufactured: 1989 Machine Format: 850 x 800mm Dcsdpfx Ajx S Uuyjfpec Technical Specifications: Convertible stock Solid up to 700 g/m2 Corrug. up to B flute Thickness 15 mm Sizes: standard boxes (blanks open) Width max 850 mm Width min 56 mm Length max 800 mm Length min 60 mm Drive System Inching speed 8 m/min Operating speed 20 - 400 m/min Crash lock bottom device Special version for 4/6 corner gluing HHS gluing system with 3 guns N. 2 gluing points disc system Belt pressing system delivery Main motor 21 kW Dimensions Length 14120 Width 2200 mm Weight 7000 - 10000 kg

Condition: good (used), Karl Tranklein PS1200 Bookbinding Shears Made in Germany. Very good condition. Dcedsx Ncxhopfx Afpsc Cutting length approx. 1200 mm Ideal for bookbinding board, corrugated cardboard, leather, and canvas. Front cutting stop with millimeter scale. Two additional sliding stops on the table. Feet-operated material clamp. High knives, in very good condition. Weighs over 400 kg

Year of construction: 2025, operating hours: 5 h, condition: like new (used), functionality: fully functional, machine/vehicle number: 2025112701, Aluminium incline conveyor with substructure Dsdpfsydb Rwsx Afpocc including leveling feet and machine feet for compensating uneven surfaces - Feed height: 500 mm - Inclined section: 4,500 mm - Discharge height: 3,000 mm Design: Aluminium construction - Reinforced triple profile 135x45 mm - Continuous galvanized discharge sheet, 2.0 mm thick Drive drum + return drum made of S235 steel, welded and machined Ø150x620 mm, crowned surface, shaft fixed with pillow block bearings. Drive: Inline geared motor 1.10 kW, belt speed 0.77 m/sec Connection: 230/400 V, 50 Hz, protection class IP54 Drive pre-wired up to terminal box (Commissioning must be carried out by qualified electrical personnel) PVC conveyor belt DM 10/2 0+005 PVC green Belt width: 600 mm Endless high-frequency-welded with stepped joint Belt material: 2-layer, particularly cross-stable 2 pcs. corrugated sidewalls, 80 mm high, 50 mm wide, edge-aligned, high-frequency welded 18 pcs. T60 cleats, 430 mm long, spacing approx. 508 mm, centrally welded on Belt material: 2-layer, particularly cross-stable Due to the corrugated sidewalls on both sides, the usable belt width is reduced: Usable width: 500 mm, as follows: (Top view) Transverse arrangement: 50 + 500 + 50 mm

Condition: new, Year of construction: 2024, Boton BTM-950Q - Year of manufacture: 2024 - New machine, only 30 operating hours - Window patching machine - Maximum blank/paper size: 950 × 780 mm - Minimum blank/paper size: 150 × 130 mm - Processable material thickness: Cardboard: 200–2000 g/m²; Corrugated board: 1–4 mm - Film thickness: 0.1–0.3 mm - Window size (max/min): 380 × 300 mm / 30 × 50 mm - Positioning accuracy: ±0.5 mm - Output: up to 9,000 sheets/hour - Pneumatics/operating pressure: 3–6 bar - Heated roller for rigid films - Servo-controlled feeder - Touch panel - PLC control Dcedpfsydpt Tox Afpsc - Modular design - Capable of gluing corner windows

Condition: new, Year of construction: 2025, functionality: fully functional, The iEcho PK-0705 Plus is a compact, fully automatic digital cutting plotter specifically designed for the graphic arts industry, packaging development, and advertising technology. It is the ideal solution for small to medium production runs where die-cutting is required without the need for expensive physical dies. Key Features: The PK-0705 Plus is an "all-in-one" system capable of cutting, creasing, and kiss-cutting in a single operation. Being digitally controlled, it eliminates the costs and lead times associated with conventional die-cutting tools. Applications: Labels, folding cartons, personalized packaging, stickers, POP displays, and greeting cards. Materials: Cardboard, corrugated board (E-flute), PVC sheets, sticker paper, and various plastics. Automatic Feeding System: The plotter is equipped with a vacuum feeder that automatically processes sheet stacks, enabling productive, unattended operation. Dedjyf D Egopfx Afpocc Oscillating Tool (EOT): Unlike basic plotters, the Plus model features a vibrating knife, allowing it to precisely cut thicker or more rigid materials (up to 6 mm). CCD Camera: A high-precision camera system automatically detects register marks on printed sheets for highly accurate contour cutting, even if the sheet is fed with a slight skew. Vacuum Table: Securely holds the material during cutting to ensure maximum precision. Working Area: 750 mm x 530 mm Max. Material Thickness: Up to 5 mm (depending on the tool) Tool Configuration: Oscillating knife, drag knife, creasing wheel Efficiency: No setup times required for die-cutting – simply load the file and start. Versatility: One device for a wide range of materials, from paper to thin rigid foam boards. Space-saving: Compact design fits into nearly any print shop. Summary: The iEcho PK-0705 Plus is a true workhorse for print shops seeking the flexibility to meet customer demands while maintaining the precision of an industrial die-cutting machine for small production runs.

Year of construction: 1968, condition: ready for operation (used), AUTOPLATEN BOBST SP 1260 E / AUTOMATIC FLATBED DIE-CUTTER STRIPPING / Year Of Production: 1968 / Max. Sheet Size: 1.260 x 920 mm / Min. Sheet Size: 500 x 350 mm / Maximum Speed: 5.000 Sheets Per Hour / Max. Solid Board Thickness: 1,5 mm / Max. Corrugated Board Thickness: 3 mm / Maximum Cutting Pressure: 500 Tons / Weight: 19 Tons / Main Dimensions: 6.075 x 2.840 x 2.200 mm Dcodpex R R R Ujfx Afpec

Condition: used, Year of construction: 2016, functionality: fully functional, type of input current: three-phase, input voltage: 400 V, air demand: 7.08 m³/h, year of last overhaul: 2025, air pressure: 87 bar, film width: 360 mm, product height (max.): 430 mm, product height (min.): 110 mm, product length (max.): 600 mm, product length (min.): 300 mm, The SAVOYE INTELIS packing machine is a fully automatic packaging line designed for packing products in corrugated cardboard boxes. The unit was manufactured in France in 2016 and features a modular plug & play architecture, enabling quick assembly, disassembly and adaptation of the process to current logistics requirements. This machine is suitable for medium to large distribution centers, e-commerce operations, contract logistics providers, and manufacturing plants. Its capacity is up to 840 cartons/hour, with a maximum single package weight of up to 32 kg. The packaging line consists of the following components (as per documentation): INTELIS F12 – Carton erector – automatic forming of boxes from corrugated board. INTELIS T18 – Shrink tunnel – carton and film stabilization through thermal shrinkage. Dodpfx Afox Uphgjpscc INTELIS C12 – Carton closer – lid application and final closing of the carton. NORDSON PROBLUE – Glue application system – professional glue applicator for packaging. Key features: - Fully automated packing cycle. - Forming, shrinking, closing, and preparing parcels for shipment. - Stable and energy-efficient transport system – conveyors with integrated roller drives. - Intelligent speed and load adjustment. - ECO mode with regenerative braking energy recovery. Technical specifications: PLC: TSXP572634M Throughput: 840 cartons/hour Carton dimensions: • min. 300 × 200 × 110 mm • max. 600 × 400 × 430 mm Max. package weight: 32 kg Power: 5 kVA Power supply: 3-phase 400 V

Year of construction: 1984, condition: good (used), BOBST I 130 ER Automatic Die-Cutting Machine Year of manufacture: 1984 2. Sheet Formats Maximum sheet size: 920 x 1,300 mm Minimum sheet size: 450 x 580 mm Working format: – Max. 890 x 1,270 mm (open chase) – Max. 900 x 1,300 mm (closed chase) 3. Material Specifications Maximum board thickness: 1.5 mm (cardboard) Minimum grammage: Dcjdpfx Afjycv Dvjpjc 90 g/m² Gripper margin: 10 mm 4. Chase Sizes – 915 x 1,300 mm chase without bar – 840 x 1,300 mm chase with bar 5. Pile Heights (Non-Stop Operation) Feeder pile height: Max. 1,500 mm with pallet Delivery pile height: Max. 1,400 mm with pallet Maximum pallet size: 900 x 1,300 mm 6. Equipment and Features – Suitable for carton and paper processing – Not suitable for corrugated board – Stripping possible using stripping frame and separation grid – EMS side lay system for alignment according to printed marks

Condition: new, Year of construction: 2026, The CNC 2030 SPECIAL milling plotter is a high-precision machine built in Poland, used for machining many engineering materials, i.e.: wood, wood-based (chipboard, MDF, OSB, etc.), plastics (Plexiglas, PVC, HPL, etc.), composites (dibond, carbon, alucobond), soft metals, etc. CONSTRUCTION: The plotter is made entirely of high quality steel. During the manufacturing process, all components undergo a special heat treatment. WORKING SURFACE: The working area of our machine tool is 2100 x 3100 [mm]. It is possible to manufacture the machine with a different working area. Z-AXIS RANGE AND GANTRY CLEARANCE: The Z-axis range is 200 mm as standard. However, it is possible to increase it to 400 mm. DRIVES: High-resolution, high-power digital motors have been used to drive our machine tools, ensuring adequate acceleration and speed in each direction. The X and Y axes use classic and well-proven helical slats, which ensure long service life and precision, and a high-performance ball screw is used to drive the Z axis. SPRING: A powerful, liquid-cooled and durable high-end brushless spindle is used to drive the cutting tool. The spindle bearings are high-quality machine bearings, which are very quiet and guarantee above-average durability. The spindle speed ranges from 6 to 24,000 rpm. SOFTWARE: The machine has been provided with suitable, easy-to-use CAD/CAM software in the latest version. CONTROL: This is done by means of a controller, which has its own processor and operating memory to ensure stable and reliable operation. The controller has a function to return to further operation after power loss so there is no need to initialise the program from scratch. VACUUM TABLE: The table is made with raster technology, thanks to the sections used we can separate any part of the table with a seal. This allows us to adapt the working area to the specific workpiece. A well-chosen vacuum pump according to the size of the table will guarantee uniform suction of the material to the table. Dcsdpfxeirmgfe Afpsc 6-POSITION LINEAR TOOL MAGAZINE: The linear magazine enables an automatic machining process. It is used for multi-tool machining. In addition, it allows for faster and more efficient work and contributes to the elimination of operator errors. The standard magazine on our machines is for 6 positions. It can be extended to 16 positions. Oscillating knife The oscillating knife is a state-of-the-art head fitted to CNC machines, designed for cutting low-density materials. The blade moves up and down and thus 'slices' the material. This makes it possible to cut thick, soft materials - FOAM foam, magnetic foils, corrugated cardboard, textiles.

Condition: excellent (used), Year of construction: 2016, As good as new machine for the production of corrugated cardboard honeycomb. New price €600,000.00 Dcsdpfx Aotqpd Hjfpsc

Condition: new, machine/vehicle number: ebf3f771e96394cd89e56bbb7, overall weight: 11,800 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis central axle trailer Welded fine-grained steel construction 6 pairs of lashing eyes bolted to the outside of the floor/outer frame, 5 tons each 2 pairs of lashing eyes additionally bolted to the floor, 5 tons each in the corners Gear support foot at the front Folding rear support 2 wheel chocks with holder Steel underride guard Rear spray flaps across the entire width Quarter-shell mudguards 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Towing device central axle trailer Towing bar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension Drum brake axles, manufacturer's choice Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Hand spindle parking brake Integral air reservoir 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, Floor Steel/ checker plate floor for high point load capacity Note: Slight floor corrugation possible due to welding distortion! Platform length approx. 5,200 mm Rear sloping to approx. 900 mm Front wall / front corner stanchions 25 mm aluminum hollow profile, 400 mm high, Drop sides 25 mm aluminum hollow profile, 400 mm high, foldable and removable Rear wall / rear corner stanchions Dcsdpei Rixrofx Afpec 1 pair of steel stanchions attached to the frame and with bracket for locking the drive-on ramps, drive-in width approx. 2,430 mm Drive-on ramps 2 steel ramps 2,300 mm long, 510 mm wide, can be moved sidewayswith grab handle on the ramps covered with 3 toothed steel rails With gas pressure jack for one-man operation Country of registration/plates Country of registration: Germany 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Front wall aluminum Side wall anodized aluminium Drive-on ramps Hot-dip galvanized Attention! These are archive pictures.

Condition: new, machine/vehicle number: a3b1347da4aa7f31dceb875db, empty load weight: 2 kg, maximum load weight: 9 kg, overall weight: 11 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis central axle trailer Welded fine-grained steel construction 6 pairs of lashing eyes bolted to the outside of the floor/outer frame, 5 tons each Front gear support leg Folding rear support 2 wheel chocks with holder Steel underride guard Rear spray flaps across the entire width Quarter-shell mudguards Towing device central axle trailer Towbar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension BPW drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Hand spindle parking brake Integral air reservoir 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear Dcjdpfx Aei Ri Ilofpoc 2 x 7-pin interchangeable plugs at the front, with connecting cable, Floor Steel/ checker plate floor for high point load capacity Note: Slight floor corrugation possible due to welding distortion! Platform length approx. 5,200 mm Rear sloping to approx. 900 mm Front wall / front corner stanchions 25 mm aluminum hollow profile, 320 mm high, Drop sides 25 mm aluminum hollow profile, 320 mm high, foldable and removable Rear wall / rear corner stanchions 1 pair of steel stanchions attached to the frame and with bracket for locking the drive-on ramps, drive-in width approx. 2,430 mm Drive-on ramps 2 steel ramps 2 300 mm long, 510 mm wide, can be moved sidewayswith grab handle on the ramps covered with wood With gas pressure jack for one-man operation Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Front wall aluminum Side wall anodized aluminium Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: 8df1ead53cc82aeb51e50a37d, empty load weight: 4 kg, maximum load weight: 13,880 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis Turntable Disposal Fine-grained steel welded construction Container locking system: - 2 pairs of locking hooks embedded in the floor - Pneumatic actuation The container locking mechanism is a 2-point design, acting from the inside, and locking of roll-off containers with an inner web is not possible (for transporting roll-off containers with a sub-frame in accordance with DIN 30722) Note! At the start of the roller recess at the front, the container must be pushed on completely flat! Longitudinal guide rails can be moved sideways and removed, rails approx. 115 mm high Turntable with strong ball bearing slewing ring 8 pairs of lashing mushrooms at the top and sides of the outer frame, 5 tons each 7 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included) 2 wheel chocks with holder Aluminum side bumpers Dsdji Ri Nujpfx Afpocc Steel underride guard Quarter-shell mudguards according to EG with anti-spray flaps according to EG Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Steel floor Roller recess for container recessed in the floor at the frontfor roll-off containers from 5,000 - 7,000 mm in length Note: Slight floor undulation possible due to welding distortion! Drive-on ramps Lockable storage space for loading ramps underneath the loading area Operating instructions A special permit is required for axle loads of 10,000 kg. Approval must be applied for individually in each federal state; the legislator does not have to grant approval for 20 t GG. Customer risk. The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Warning sign according to ECE - 70 Paint finish Frame DB 7350 nova gray 15-year warranty against rusting through Note: Bottom corrugation possible due to hot-dip galvanizing! Drawbar KTL black Attention: Archive pictures!

Year of construction: 1998, condition: like new (used), functionality: fully functional, machine/vehicle number: 2550, The FP4/EC is an automatic and adjustable machine for forming and gluing both, corrugated and solid board boxes. Dedpfxoxiva Aj Afpjcc It is able to form multiple designs of different column construction like closed column, open column, L-column trays with different weights of cardboard. It has 4 speeds reaching up to 1,400 trays/hour. The machine is available for sale immediately.

Condition: used, L: 1240, W: 1045, H: 680 (mm). Product: Stacking box steel. Type: Fixed construction. Version: With front opening. Material: steel. Walls: corrugated steel plate. Floor: profiled steel. Euronorm (mm): 1200 x 1000. Colour: green. Surface treatment: painted. Dsdpfxewprz So Afpscc Internal length (mm): 1120. Internal

Condition: excellent (used), Year of construction: 2017, machine/vehicle number: SEM126/TH46098, Automatic Carton Folder Gluer, Max open blank width: 1100 mm, Min open blank width: 126 mm, Max feed up length: 800 mm, Min feed up length: 60 mm Stock : Cartonboard up to 800 gsm, Corrugated up to E flute.Max belt speed i: 425 m/min Dcjdpfev Ipl Tex Afpoc Complete with : Bottom belt feeder, Back lifters with vibration for smooth and consistent feeding, Pre-breaking system, Small box attachment - allowing min 76mm open blank width, Crash-lock module, Bottom left hand side glue pot, Three belt carrier folding section, Heavy duty Double Trombone delivery, Compression belt section, HHS C-1100 8 B cold glue system, 4 x HHS glue guns, Remote control, Manuals and electrical diagrams.

Condition: new, Year of construction: 2024, Osama Automatic 4-Roller Glue Application Machine Model: S4R/P-1400 Automatic gluing machine with 2 motors Working width: 1,400 mm Max. pass-through height: 0 - 100 mm Speed: 22 m/min Djdpfx Afju I R Utepjcc Working height: 900 mm Diameter of application rollers: 250 mm Motor power: 3 kW Electrical: 400 V / 50 Hz / 3 phase Automatic gluing machine with 4 rollers for polyvinyl acetate (PVAC), urea-formaldehyde (UF), and polyurethane adhesives, suitable for various materials such as MDF, multi-layer boards, particle boards, composites, and gypsum plasterboard. This type of gluing machine allows for precise and homogeneous dosing of adhesive, taking into account the corrugation of the rollers, which must be suitable for the respective production requirements. The heavy-duty structure and the roller cores, manufactured with greater thickness compared to earlier models, enable a high production rate without issues and bonding of materials up to 2200 mm in width. Roller removal for maintenance is straightforward, as the supports can be split in two via a simple bayonet coupling. The gluing machine can also be equipped with different accessories, such as an electronic speed controller, automatic roller washing device, and an automatic upper roller lifting mechanism with position display on the control panel. The S4R/P gluing machine is used in various production sectors, including construction and the manufacturing of foam panels and mattresses. Equipment: - Automatic roller cleaning - Infeed roller - Outfeed roller - Working height: 900 mm - Infeed table TRF 1400x3000 mm with PVC rollers, 60 mm diameter, 200 mm spacing - Outfeed table TDF 1400x3000 mm with disc rollers, D: 122 mm, stainless steel Location: in stock at 54634 Bitburg - Available immediately -

Condition: used, Year of construction: 2019, functionality: fully functional, total height: 1,800 mm, input voltage: 400 V, total width: 2,830 mm, total length: 2,300 mm, overall weight: 2,500 kg, working width: 1,950 mm, operating pressure: 6 bar, Kolbus Autobox BX200 with magazine feeder - Boxmaker for the production of custom folding cartons - Magazine feeder for automatic material feed - Automatic setting via touchscreen - Processes corrugated board up to max. 10mm - Slot knife width 7mm - REMOTE service possible Dodpfeyaa Rnjx Afpecc

Condition: used, Göpfert Flexo-Folder-Gluer / Flexo-Printer-Slotter line, model EUROLINE EL 310 / Euro-Inline 310 E The machine is designed for the production of corrugated packaging and combines printing, creasing, slotting, folding, and gluing in a continuous inline process. It is highly suitable for medium to large production runs and offers a robust industrial construction with versatile automation features. Comprising: - Feeder - Flexo printing units (2 units) - Slotting unit (motorized/SLM) - Rotary die-cutter - Folding/gluing section Dodpfxox Thxzo Afpjcc - Pre-set function - Strapping machine

Condition: used, Plastic Boxes Made of Corrugated Plastic | GWP Group | €1 / unit | 300 units per pallet For sale: high-quality plastic boxes made of corrugated plastic from manufacturer GWP Group, material Correx. Ideal for use as storage bins, picking crates, stackable boxes, and open-front storage bins. Features: ✔ Moisture resistant ✔ Oil and dirt resistant ✔ Load capacity up to 5 kg ✔ Lightweight, robust, and durable Technical Data: Dimensions: 425 × 366 × 310 mm Material: Corrugated plastic Condition: used, clean Packaging: 300 units / 1 Euro pallet Price: €1 net per unit Block: 30 units (6 rows) Pallet: 300 units Delivered disassembled, palletized Suitable applications: • Warehouse • Logistics • Order picking • Workshop • Production • Shipping Djdpjx Tgz Isfx Afpscc Collection: 97514 Oberaurach Delivery available by arrangement Larger quantities available Keywords: plastic boxes, storage bins, open-front bins, stacking boxes, picking crates, corrugated plastic boxes, storage containers, logistics boxes

Year of construction: 2026, condition: new, Specification: Maximum sheet size 740 x 1060 mm Minimum sheet size 330 x 400 mm Max. cutting pressure 3.0 MN Maximum number of strokes per hour 8.000 sh/h Suitable for following material Paper to a minimum weight of 80 g/m² Carton board up to a maximum thickness of 2.000 g/m² Corrugated board up to a maximum thickness of 4 mm Dcjdpfxjlyqrco Afpec Equipment: Non-Stop-feeder Manual Non-Stop device for the feeder Stripping station including auxiliary pile for Non-Stop delivery Centerline operator platform 1 tool set Machinedelivery 6-8 month after order

Year of construction: 2026, condition: new, Specification: Maximum sheet size 570 x 820 mm Minimum sheet size 230 x 280 mm Max. cutting pressure 1.8 MN Maximum number of strokes per hours 8.000 sh h Suitable for following material Paper to a minimum weight of 80 g/m² Carton board up to a maximum thickness of 2.000g/m² Corrugated board up to a maximum thickness of 3 mm Equipment Feeder Strippingstation including auxiliary pile for Non-Stop delivery Centerline 1 tool set Dcodpfx Afolyqpdopsc Machinedelivery 6-8 month after order

Year of construction: 2026, condition: new, Specification: Maximum sheet size 740 x 1060 mm Dcedjlyp Emspfx Afpjc Minimum sheet size 330 x 400 mm Max. cutting pressure 3.0 MN Maximum number of strokes per hour 9.000 sh/h Suitable for following material Paper to a minimum weight of 80 g/m² Carton board up to a maximum thickness of 2.000 g/m² Corrugated board up to a maximum thickness of 4 mm Equipment: Non-Stop-feeder Manual Non-Stop device for the feeder Stripping station including auxiliary pile for Non-Stop delivery Centerline operator platform 1 tool set Machine delivery time: 6-8 month after order

Condition: used, Year of construction: 2008, Machine Overview Automatic tray plus film packer ATLANTA COMBIGIOTTO 90-M designed for secondary packaging of bottles with 90° side infeed. The machine forms a corrugated tray and wraps the product with neutral shrink film, then conveys it through a shrink tunnel to obtain stable, retail-ready bundles. Ideal for beverage lines handling PET, glass or HDPE bottles. Reference No. FA56. Year 2008, overhauled in 2022. Condition: Ready for operation. Indicative output up to 25 packs/min, depending on product and format. Operating concept: automatic grouping of bottles, tray forming/loading, film wrapping and shrink-tunnel consolidation. Packaging configuration: Tray + neutral film (shrink). 90° infeed enables compact layouts and easy connection to existing conveyors. Key Technical Data Make / Model: ATLANTA COMBIGIOTTO 90-M Operating type: Automatic Infeed orientation: 90° side infeed Packaging: Tray + film (neutral) Tray magazine/formation: Available Nominal capacity: up to 25 bundles/min (format and product dependent) Year: 2008 (overhauled 2022) Condition: Ready for operation PLC: SIEMENS S7 E 300 Automation & Control Industrial PLC-based control with operator HMI for recipe selection, speed setpoints and diagnostics. Inverter-controlled drives for smooth acceleration and product handling. Photoelectric sensors for product presence, jam and film detection. Temperature-controlled shrink tunnel for consistent film performance. Interlocked access doors with safety monitoring for guarded zones. Line Integration Dcjdpfsx H Thzox Afpsc Upstream: accepts bottles from conveyor with 90° transfer to the infeed section; integrated selection/divider to create pack patterns before tray loading. Downstream: discharge conveyor after shrink tunnel for connection to inspection, case handling or palletizing. Signals and handshakes typically include start/stop, fault, emergency stop circuit integration and speed reference. Mechanical interface and layout drawings available on request for line engineering. Condition & Maintenance General overhaul performed in 2022. Machine presented as ready for operation. Preventive maintenance recommended: periodic checks of film path, knife/sealing components, tray magazine/erector, lubrications and conveyor wear parts. Performance & Versatility Suitable for a wide range of cylindrical or square bottles commonly used in beverages. Typical pack patterns achievable for bottles (e.g., 2×2, 3×2, 4×3, etc.) depending on container size and tray dimensions. Neutral shrink film for clear presentation; tray provides rigidity and stacking strength. Consistent bundle quality via controlled film wrapping and thermal shrink process.

Condition: good (used), Year of construction: 2019, functionality: fully functional, The Kolbus AB300 is a fully automatic, modular machine for the production of corrugated cardboard boxes, capable of manufacturing a variety of box styles (such as 0201, tray, wrap, and pallet boxes). Key specifications include a maximum speed of up to 100 m/min, fully automatic setup via touchscreen, a maximum blank width of 2590 mm (102 inches) with unlimited length, and the capability to produce over 100 different box styles. The machine offers high flexibility, allowing for rapid changeovers between different sizes and styles. Technical Specifications - Maximum speed: up to 100 m/min - Widths: from 100 mm to 2590 mm (102 inches) - Length: Unlimited - Box types: Over 100 different styles, including 0201, wraps, pallet boxes, and partitions Dcedpfx Aexpga Tjfpsc - Control: Fully automatic setup via touchscreen - Energy efficiency: Up to 75% energy savings compared to conventional machines - Material: Suitable for all types of corrugated board