Used Cross Cut for sale (17,323)

Year of construction: 2013, condition: used, Technical data of the bale opener line for RDF. MSW, paper, cardboard: Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland Type BO 4000 Year of manufacture 2015 Quantity of opened bales 674 pieces Operating time only 3 days, exclusively by running in the entire line during new installation Opening time approx. 45 seconds per bale Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm Max. Bale weight 2,000 kg Conveying height of the system 1,400 mm Max. Conveying width of the system 1,200 mm Material to be opened RDF/MSW Availability of the line 98% Noise level of the bale opener line 85 dB(A) Total connected load 37 kW Rated current 125 A Operating display SIEMENS SIMATIC HMI Touch Control SIEMENS S7 ET200S Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h) Scope of delivery: Feed conveyor 3,500 x 1,200 x 1,400 mm Feed conveyor to opener 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in hydraulic oil tank Heating in control cabinet Oil cooler in Hydraulic unit Explanation of the short period of use: The entire line of Cross Wrap bale openers type BO 4000 was installed at a municipal waste incineration plant in 2015. The background to the installation was that in the case of a malfunction or maintenance of the incinerator, the municipal waste could continue to be received, baled, wrapped and stored until the malfunction was cleared. Then the bales should all be opened again and the waste fed into the normal incineration process. This worst-case scenario never came to pass. The plant was set up, run in and then never used in regular operation. Only during the commissioning and running-in of the entire plant in 2015 were 674 bales opened on three days. The plant is in very good condition and ready for operation immediately. Due to reconstruction measures in the incineration plant, the installation area of the bale opener was needed. As a result, the entire line is for sale. Short description of the wrapping process: The pressed bales are placed on the infeed conveyor belt from the side or from behind by means of a forklift truck. For opening, the bales must run horizontally to the conveyor belt with the wire or twine binding, otherwise the bales must be turned 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or twine strapping. The front and rear rotating knives slit the bale lengthwise. Afterwards, the gripper returns to the starting position. The opened bale is now conveyed via the conveyor belt to the discharge chute and then falls onto the following conveyor system. Comments: New price of the completely plant 296.000,- €. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) is complete. The unit has been dismantled into freight-manageable units, stored and is available for inspection and loading at short notice. We do not accept any liability for the technical details or any errors. Godpfx Anou Tg I Djxjit

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: COMPACT, The COMPACT model plasma cutting machine is a machine model that protects your budget through lower investment and reduced costs, prioritizing reliability, user-friendliness, and compactness as its three main principles. The Compact is a valid solution for the needs of a wide market segment, offering an excellent cost/benefit ratio for anyone dedicated to sheet metal processing. COMPACT is characterized by a monoblock design with a compact layout, making it easy to transport and suitable for medium and small workshops. This system is ideal for high-capacity plasma power sources. The system comes equipped with an extraction filter and plasma power source, and it can be configured with various CNC and software options depending on customer requirements. The Compact can feature a working range between 1,500mm x 3,000mm and 2,000mm x 6,000mm. Giedpfxeyzm S Ao Anxst

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: PLASMA CUTTING, Equipment: documentation/manual, The PROCUT model plasma cutting machine is designed to operate under all conditions. Its main advantage is a robust frame structure, making it suitable for heavy industrial use. Rails and frames are the most critical factors during the cutting process. They ensure that the machine remains stable and in good condition for a longer lifespan. It can be equipped with high-capacity power sources in sizes ranging from 1,500mm x 3,000mm up to 3,000mm x 12,000mm. All customer requirements can be integrated into the strong construction of PROCUT. This allows it to meet customer demands in the best possible way. Custom manufacturing in requested dimensions is possible, depending on your requirements and workspace. Gjdpoyzhl Defx Anxjit

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: COMBO (Plasma, Drilling, OXY-Fuel, Bevel), Equipment: CE marking, documentation/manual, * COMBO offers customers the most innovative technological solutions and features a wide range of models. * It is a highly advanced machine equipped with a 6- and 12-station automatic tool changer ISO 40 drilling system, offering capabilities such as drilling, tapping, countersinking, plasma cutting, OXY cutting, and ±45° bevel cutting. * The COMBO has a working range from 1,500 mm x 3,000 mm up to 4,000 mm x 24,000 mm and can be equipped with high-capacity plasma power sources. * Plasma Cutting * Drilling * Tapping * Countersinking * OXY-Fuel Cutting * Fully welded, heavy-duty machine frame. Giedpfx Aoyy Rn Sonxst * High-durability cutting table designed for easy replacement. * Dual drive system with linear rails, rack and pinion. * Compliance with CE standards. ISO 40 Drilling System * 6-station automatic tool changer (optional 12-station). * CNC-controlled automatic coolant spraying system during cutting. * 26 kW spindle motor power. * Drilling capacity: Ø M5 to Ø M40 (HSS, UDRILL). * Drilling depth: 100 mm * Drilling speed: 0.15 – 0.35 mm/rev. * Spindle speed: 1,500 rpm * Hypertherm / Thermal Dynamics power sources. * Hypertherm / Eurosoft CNC controls. * Possibility to import .dxf and .dwg files via Pronest / Cut-Expert CAD-CAM.

Condition: new, functionality: fully functional, Year of construction: 2026, machine/vehicle number: MASTER PLUS (Müşteriye Özel Ölçüler), control type: CNC control, laser type: fiber laser, type of cooling: water, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, emergency stop, safety light barrier, * MASTER PLUS is a high-capacity, technologically advanced fiber laser cutting machine primarily used for cutting large metal sheets. It is capable of processing long, wide, and various materials in a single operation. For materials of variable sizes, it allows for flexible operation by creating continuous, uninterrupted, and independent cutting zones at different points of the machine. Enables higher production speeds and increased efficiency when processing large-volume materials, leading to significant savings in time and labor. * Single table, fixed cutting bed. * Customizable, available with a wide range of cutting areas. * Equipped with Raycus, MaxPhotonics, and IPG resonators. * Features Raytools, Precitec, and Bochu laser cutting heads. * LYNCA/CYBELEC, Eurosoft, ESA CNC systems. Godpfx Aneyy Nrvjxjit * 21.5'' touch screen for easy operation. * CE-compliant. * Configurable with fiber laser sources from 2kW up to 30kW. * Bevel cutting option available. * User-friendly design, easy access to the cutting area. * Thermally processed, robust monoblock welded steel frame for enhanced structural integrity. * Aluminum bridge design provides higher resistance and dynamic performance. * Energy saving through low power consumption. * Remote service capability. * Automatic lubrication system. * Since both design and manufacturing are done in-house, custom production is available according to customer requirements.

Condition: new, functionality: fully functional, Year of construction: 2026, machine/vehicle number: MASTER 1500x3000mm / 1500x4000mm / 2000x4000mm / 2000x6000mm / 2500x6000mm, control type: CNC control, laser type: fiber laser, laser source manufacturer: RAYCUS - MAXPHOTONICS - IPG, type of cooling: water, Equipment: CE marking, documentation/manual, * The MASTER series fiber laser cutting machines deliver high cutting performance, thanks to their robust frame construction and compatibility with power sources up to 30 kW. * Equipped with an automatic, rear-exchange dual shuttle table. * The standard configuration of the MASTER includes a rear table exchange system and the option to integrate automated loading and unloading systems. Gisdpfoyy I N Hex Anxst * Customizable cutting areas are available. * Working ranges: 1,500x3,000 mm / 1,500x4,000 mm / 2,000x4,000 mm / 2,000x6,000 mm / 2,500x6,000 mm. * Available with Raycus, MaxPhotonics, and IPG resonators. * Compatible with Raytools, Precitec, and Bochu laser cutting heads. * LYNCA/CYBELEC, Eurosoft, ESA CNC control units. * Enhanced usability with a 21.5'' touchscreen interface. * Compliant with CE standards. * Can be equipped with fiber laser sources ranging from 2 kW to 30 kW. * User-friendly design ensures easy access to the cutting area. * Rigid, monoblock, welded steel frame with heat treatment ensures high durability and mechanical stability. * Aluminum bridge design provides added rigidity and excellent dynamic performance. * Designed for energy efficiency with low power consumption. * Remote service capability. * Automatic lubrication system included. * As design and manufacturing are performed in-house, customization according to customer-specific requirements is possible.

Condition: new, functionality: fully functional, Year of construction: 2026, machine/vehicle number: EDGE PLUS 1500 x 3000mm / 1500 x 4000mm, control type: CNC control, laser type: fiber laser, laser source manufacturer: RAYCUS - MAXPHOTONICS - IPG, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, emergency stop, safety light barrier, * Raycus, MaxPhotonics, and IPG resonators. * Raytools, Precitec, and Bochu laser cutting heads. * LYNCA/CYBELEC, Eurosoft, ESA CNC systems. * 21.5'' touchscreen for high ease of use. * Dual table cutting system with side loading and motorized table exchange. * Occupies 40% less floor space compared to a standard fiber laser cutting machine. * Easy and cost-effective transportation. * CE compliant. * Compact design with a transverse, removable cutting table. * Can be equipped with fiber laser sources ranging from 2kW to 12kW. * Working range: 1,500mm x 3,000mm and 1,500mm x 4,000mm. * User-friendly and provides easy access to the cutting area. * Rigid, monoblock, welded steel body and robust machine structure, thermally stress-relieved. * Aluminum gantry design for increased rigidity and high dynamic performance. * Energy-saving with low power consumption. Gisdpfx Ajyy Iyrsnxjt * Remote service capability. * Automatic lubrication system. * Customized production available according to specific client requirements, as both design and manufacturing are carried out in-house.

Condition: used, Cut Max Guillotine Type: GM-1 Efficiency: 1500 kg/h Operating temperature: up to -20°C Machine dimensions: 2100 x 900 x 1850 mm Made of stainless steel Power supply: 3x400V 50 Hz Weight: 550 kg Gijdpfxjy Ega Uj Anxet Condition: used/overhauled/ready to work

Condition: new, functionality: fully functional, Year of construction: 2026, machine/vehicle number: EDGE 1500 X 3000 / 1500 X 4000, control type: CNC control, laser type: fiber laser, laser source manufacturer: RAYCUS - MAXPHOTONICS - IPG, type of cooling: water, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, emergency stop, * Raycus, MaxPhotonics and IPG resonators. * Raytools, Precitec, and Bochu laser cutting heads. * LYNCA/CYBELEC, Eurosoft, ESA CNC. * High user convenience with a 21.5'' touchscreen display. * Occupies 40% less floor space compared to a conventional fiber laser cutting machine. * Easy and cost-effective transportation. * CE conformity. Gisdpfx Asyyxpqenxot * Features a compact design and a transverse removable cutting table. * Can be equipped with fiber laser sources ranging from 2kW to 6kW. * Working range: 1,500mm x 3,000mm and 1,500mm x 4,000mm. * User-friendly, with easy access to the cutting area. * Thermally treated, robust, monoblock welded steel frame for enhanced rigidity. * Aluminum bridge design provides increased strength and high dynamic performance. * Energy saving through low power consumption. * Remote service capability. * Automatic lubrication system. * Production according to customers’ special requirements, as both design and manufacturing are carried out in-house.

Condition: like new (used), Range (in depending on the lighting conditions) until: 15 m Range with laser receiver: 30 m, & more 5 m: leveling accuracy +/-1 mm Self leveling range: 4° +-0,5 ° Accuracy of the horizontal line at 5 m: +-1.5 mm Accuracy of vertical line at 3 m +-0.75 mm Number of laser lines: 2 Weight: 485 g Gjdpfed Ecncjx Anxsit

Condition: new, Year of construction: 2026, functionality: fully functional, High-performance double-rip crosscut saw designed for seamless integration into automated board production and stacking lines. Key Features: Perfect Integration: Specifically built to operate within a board stacker line. Gijdpeyhbamofx Anxst Synchronized Workflow: Automatically matches the speed of the stacker for maximum efficiency. Clean Cuts: Precise double-blade system for high-quality cross-cutting. Industrial Build: Designed for 24/7 sawmill environments. Ideal for: Sawmills looking to automate the transition from cutting to stacking with zero bottlenecks.

Condition: used, Year of construction: 1982, Used cut-to-length line FIMI 1250×0.12-0.8mm x16t with two packing stations (A3793) is coil metal processing line to cut metal into sheets with required sizes. Such machine can be good solution for metal coil processing companies. Manufacturer : FIMI – Italy Year of manufacture : 1982 Revamping : 2008 (SEI SISTEMI) and 2019 (SEI SISTEMI) Ce marking : 2019 Material before processing : Max coil width 1250 x 0.12 Г· 0.80 mm. Uncoiler capacity : 16 Tons. Sheets dimensions : min. 300 x 500 mm. – Max 1250 x 2000 mm. Working speed 0-120 m/min. LIST OF MACHINES COMPOSING THE LINE Giodpfxottlfke Anxjt ➢ STOCKING RAMP FOR 2 COILS ➢ COIL LIFT ON UNCOILER ➢ UNCOILER WITH SECTORS DIAM. 400 AND DIAM. 508 MM. ➢ PINCH-ROLL FOR STRIP FEEDING TO LEVELER ➢ 6HI-LEVELLER WITH INTERCHANGEABLE ROLL BENCHES – 1 BENCH FOR THICKNESS 0.12 ÷ 0.50 MM. – 1 BENCH FOR THICKNESS 0.50 ÷ 0.80 ➢ CONNECTION TABLE BETWEEN LEVELER AND PINCH-ROLL ➢ PINCH-ROLL ➢ DESCENT ROLLWAY IN LOOPING PIT ➢ ASCENT ROLLWAY FROM LOOPING PIT ➢ PINCH-ROLL WITH MOTORIZED ROLLS ➢ STRIP CENTERING DEVICE WITH VERTICAL ROLLS ➢ THICKNESS MEASURER TYPE ELECTRONIC KEYBOARD ➢ ROTATING SHEAR ➢ SWIVELLING CONVEYOR TO AVOID SCRAPS AND PARTS OF DEFECTIVE STRIP ➢ COLLECTION BOX FOR TRIMMING AND DEFECTIVE PARTS OF THE STRIPS ➢ SWIVELLING CONVEYOR TO AVOID SCRAPS AND PARTS OF DEFECTIVE STRIP IN THE FIRST AND SECOND COLLECTION BOXES AND STACK COMPOSITION ➢ CONNECTION ROLLWAY AND SECTION FOR CONVEYING OF SHEETS IN THE THIRD BOX. ➢ 3 STACK UNLOADING SHUTTLES TO CONVEY STACKS TOWARDS THE ROLLWAY ➢ 1 EVACUATION ROLLWAY FOR THE PACKAGING ➢ HYDRAULIC EQUIPMENT FOR ALL THE LINE ➢ INTRODUCTION STRIP OPERATION PULPIT LOCATED AT LINE ENTRY FOR COILS CUTTING ➢ MAIN PULPIT FOR ALL LINE OPERATIONS ➢ OPERATION PULPIT LOCATED AT LINE EXIT ➢ ELECTRICAL CABINET CONTAINING ALL ELECTRICAL/ELECTRONIC COMPONENTS AND PLC ➢ PHOTOCELLS AND SAFETY/PROTECTION BARRIERS.

Condition: used, Cut-to-length line Bronx 2050x8mm x35t (A3781) for coil metal cross cutting into sheets of required sizes with different length and width. Thickness Range: 2 – 8 mm Coil Capacity: 35t Coil OD: 2100mm Coil ID: 508mm , 610mm , 762mm Strip Width: 2000mm – 600mm Sheet Length: 8000mm – 600mm Pack Weight: 10 t Max Line Speed: 60 meters/min Cuts Per Minute: 35 Complete Line With 4 Coil Storage Storage Ramp Coil Loading Car Double Stub Mandrel Uncoiler Sliding Base Hydraulic Expansion Drag Brake Tension Control Peeler / Hold Down Roll 3 Roll Coil Breaker Feed Up Table 7 Roll Backed Up Leveler with Pinch Roll Breaker (9 Rolls Total) Entry Power Pinch Rolls 3 Flights Top & Bottom Back-Up Rolls Entry & Exit Pinch Rolls Marking Unit Measuring Roll Pinch Rolls Bronx Flying Shear AC Die Accelerator Flywheel & Air Clutch and Brake Rack & Pinion Accelerator Giedpfx Ajq Ulh Hsnxst 35 Cuts per Minute Reject Conveyor Twin Belt Gauging Table Stacker Side Squaring Lift Stacking Tables Photo Cells Drop Type Motorized End Stop Motorized Run Out Conveyor Upgraded AC Motors Upgraded Control Techniques Digital Drives Complete Line

Condition: good (used), Year of construction: 2008, travel distance X-axis: 1,100 mm, travel distance Y-axis: 610 mm, travel distance Z-axis: 610 mm, rapid traverse X-axis: 32 m/min, rapid traverse Y-axis: 32 m/min, rapid traverse Z-axis: 32 m/min, rotational speed (max.): 10,000 rpm, Control system: Heidenhain iTNC 530 Technical specifications: Travel distances: X-axis: 1,100 mm Y-axis: 610 mm Z-axis: 610 mm Rapid traverse (X/Y/Z): 32 m/min Feed rate (X/Y/Z): 12 m/min Distance table surface – spindle nose: 120 – 730 mm Maximum speed: 10,000 rpm Torque: 332 Nm Drive power: 13 kW Tool holder: SK 40 Tool positions: 30 Table dimensions: 1,250 x 610 mm Maximum table load: 900 kg Connected load: 35 kW Gsdpfox Hfnmsx Anxsit Machine weight: 7,500 kg Chip conveyor Internal coolant supply (ICS): 22 bar Coolant tank capacity: 250 liters Air through spindle center

Condition: good (used), Year of construction: 2017, functionality: fully functional, working range: 3,050 mm, travel distance X-axis: 3,050 mm, travel distance Y-axis: 1,525 mm, travel distance Z-axis: 220 mm, positioning accuracy: 0.015 mm, input voltage: 400 V, table length: 3,050 mm, operating speed: 250 mm/s, table width: 1,525 mm, pressure: 4,137 bar, positioning speed: 15 m/min, rapid traverse X-axis: 15 m/min, rapid traverse Y-axis: 15 m/min, table height: 840 mm, operating pressure: 4,137 bar, input current: 77 A, total height: 1,300 mm, total length: 4,210 mm, total width: 2,130 mm, water pressure: 2.8 bar, pump pressure: 4,137 bar, overall weight: 3,850 kg, working length: 3,050 mm, power: 37 kW (50.31 HP), Equipment: safety light barrier, 2017 Swiftcut Swift-Jet CNC Waterjet Cutting Machine – Under 900 Hours Use High-Precision CNC Waterjet Profile Cutter – Low Hours, Good Condition – Now Available at Used Machine Tools Ireland Ltd 🔍 Overview: We are offering this 2017 Swiftcut Swift-Jet Waterjet Cutting Machine, a top-tier solution for high-precision, cold-cutting of a wide range of materials including metal, stone, plastic, glass, and composites. With less than 900 operational hours, this machine is in very good condition and ideal for any business seeking reliable, accurate, and versatile cutting performance. 🛠️ Machine Specifications: Brand: Swiftcut Model: Swift-Jet Year of Manufacture: 2017 Technology: CNC Waterjet Profile Cutting Cutting Area: 3000 x 1500mm Hours Used: Less than 900 hours Pump Type: High-pressure waterjet pump Cutting Method: Abrasive and pure water capability Software: Swiftcut Control Software (user-friendly, intuitive interface) Table Dimensions: 3000 x 1500mm Max Sheet Size: 3050 x 1525mm (10' x 5') Max Traverse Speed: 15m.min Max Z Axis Clearance: 220mm Positional Accuracy: 0.015mm Tank Depth: 840mm Max Pressure: 60,000psi(4137bar) Continuous Pressure: 60,000psi Min. Piercing Pressure: 20,000psi Max Output Flow: 3.8l/min Max Orifice Size: 0.36mm Min Orifice Size: 0.13mm Cutting Water Infeed: 7.6l/min Water Pressure Infeed: 2.8bar Pump Voltage: 400V/77A Pump Power: 37kW/50HP Machine Voltage: 1ph/16A Water Treatment Voltage: 1ph/10A Garnet Hopper Voltage: 1ph/10A Machine Dimensions: 4210 x 2130 x 1740mm Pump Dimensions: 1850 x 920 x 1300mm Machine Weight: 2400kg(empty) Pump Weight: 1450kg 🌟 Key Features: Cold-cutting process – no heat-affected zones, preserving material integrity Precise and clean cuts on a variety of materials and thicknesses Gijdpfxswb D S Ho Anxet Ideal for metal fabrication, signage, engineering, prototyping, and more Compact footprint, easy installation, and low maintenance Exceptional build quality from a trusted UK manufacturer 🔧 Applications: Perfect for cutting: Mild Steel, Stainless Steel, Aluminium Brass, Copper Stone, Granite, Marble Plastic, Acrylic Glass, Rubber, Composite Materials ✅ Why Choose This Swift-Jet? Very low hours – lightly used and well maintained Excellent condition – ready to work immediately Cost-effective alternative to brand new equipment Supported by Swiftcut's strong reputation for service and performance Take advantage of this rare opportunity to own a high-spec waterjet cutting system with low hours – ideal for precision fabrication. Act quickly – this unit won’t last long! Used waterjet cutting machine Ireland, Swiftcut Swift-Jet for sale, CNC waterjet profile cutter, low hours waterjet machine, 2017 Swift-Jet waterjet, metal and stone cutting machine, abrasive waterjet cutter, used CNC cutting machines Ireland, high-precision waterjet cutter, used fabrication equipment for sale Notes: *Specifications are given in good faith but not guaranteed*

Condition: used, Year of construction: 2011, x-travel 1100 mm y-travel 610 mm z-travel 610 mm Giedpfx Anjyk Ifhexot control Heidenhain 530 weight of the machine ca. 7800 kg

Condition: excellent (used), Year of construction: 1997, Rip and cross saw REMA DMLK 30 Producer of REMA Machine model / type DMLK 30 Year of production 1997 Machine category Longitudinal and transverse saw Location Gorzów Wlkp. Conditions of delivery PERSONAL COLLECTION Cost of delivery Customer cover Startup type to be agreed Gedpfxjfv Hphs Anxjit Description Comments - after the technical review - very good condition - year of production 1997 TECHNICAL PARAMETERS: main engine 3.9 kW trolley length 1370 mm blade diameter 300 mm angle adjustment 0 - 45 " height adjustment cutting height max. 90 mm cutting width on the right side 885 mm ruler length 1350 mm ratchet extended receiving table two kinds of blade rotation speed 3700 and 5000 RPM The protractor visible in the photos is an additional option for PLN 400 net dimensions: length / width / height 135 x 85 x 135 cm weight ~ 320 kg

Year of construction: 1970, condition: used, Cut Tape BRENTA torso 1200 Location Gorzow Wielkopolski. Conditions of delivery Cost of delivery Client cover startup type Giedpfxocudizj Anxjt negotiated Description Comments Vertical band saw blade stylitowane carbide wheel diameter 1200 mm, adjustable mechanical feed, feed regulation smoothly on the tape and the wheels flat, cast iron, no need to anchor. Important machine has the ability to cut diameters up to 330 mm, new electrics, a complete ready to go, belt width 200 mm stylit, after pouring rubber on the wheels do not need to regenerate.

Condition: used, Cut-to-length line Pro-Eco with Cassette Type Precision Leveler 60 x .187 x 50,000Lbs (A3789) Maker: Pro-Eco Excellent conditions Gjdothg Diopfx Anxjit SPECIFICATIONS: MAX WIDTH 60" MAX THICKNESS 187" MANUFACTURER - PRO-ECO YEAR - 1985, REINSTALLED 2002 WIDTH RANGE - 8" to 60" GAUGE RANGE - .024" to .187" WEIGHT CAPACITY - 50,000# (25 TON) COIL OD - 36" to 72" COIL ID - 19" to 24" SHEET LENGTH - 24" to 168" SHEET WIDTH - 8" to 62" PACK HEIGHT - 30" (INCLUDING DUNNAGE) PACK WEIGHT - 20,000# LINE DIRECTION - RIGHT to LEFT LINE SPEED - 50 to 300 FPM (VARIABLE) LEVELER TYPE - MECHANICAL WEDGE STYLE w/ TWO CASSETTES LINE COMPONENTS: FOUR ARM ENTRY STORAGE TURNSTILE FLOOR LEVEL COIL LOADING CAR CANTILEVERED MANDREL UNCOILER w/ WATER COOLED BRAKE PIVOTING AND TELESCOPING PEELER BLADE ENTRY PINCH ROLLS ROLLER TYPE SIDE GUIDES ENTRY CROP SHEAR SIDE TRIMMER HYDRAULIC SERVO DRIVE (CURRENTLY NOT OPERATIONAL) MECHANICAL STYLE LEVELER FRAME W/ 200 HP MOTOR CASSETTE #1 - 19 ROLL, 2.50" DIAMETER, 5 HI, 7 BACKUP FLIGHTS CASSETTE #2 - 19 ROLL, 1.75" DIAMETER, 5 HI, 7 BACKUP FLIGHTS STRIP INSPECTION AND CARRY-OVER TABLE w/ NON-MARKING ROLLS LOOPING PIT QUADRANT TABLES w/ NON-MARKING ROLLS ROLLER TYPE STRIP SQUARING TABLE PRECISION ROLL FEEDER W/ 55 HP MOTOR HIGH SPEED MECHANICAL CUT OFF SHEAR W/ 40 HP MOTOR BLANK INSPECTION CONVEYOR w/ NON-MARKING BELT REJECT BELT CONVEYOR w/ NON-MARKING BELT AND SCRAP CART 14 FOOT AIR FLOAT STACKER w/ SQUARING GUIDES AND END STOP 14 FOOT STACKER LIFT CONVEYOR w/ END DISCHARGE ROLLERS 14 FOOT STACKER RUNOUT CONVEYOR w/ END DISCHARGE ROLLERS OPERATOR CONTROL STATIONS UPDATED AC CONTROLS w/ ALLEN BRADLEY "CONTROL LOGIX" PLC (2006) UPDATED DRIVE CONTROLS w/ SIEMENS "SIMOREG" CONTROLLERS (2006) CLOSED LOOP HYDRAULIC SYSTEM CLOSED LOOP WATER COOLING SYSTEM

Condition: good (used), Marel SC90 Salmon Slicer Salmon Slicer Model: SC90 Silk Cut 11 D Cut slicer Single Lane With adjustable slice thickness and angle Up to 90 slices per minute Slice angle: 8-20 degree Gsdpfx Ajv Dmz Donxoit Dual frequency 50/60Hz

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2019, machine/vehicle number: 10089060/30042621, total length: 5,300 mm, total width: 2,100 mm, total height: 2,300 mm, year of last overhaul: 2024, No reserve price – guaranteed sale to the highest bidder! The machine was last overhauled in 2024! TECHNICAL SPECIFICATIONS Material loading area: 4,000 mm x 2,000 mm MACHINE DETAILS Godpfxoy Nkzqs Anxoit Dimensions (L x W x H): 5,300 x 2,100 x 2,300 mm EQUIPMENT Service and inspection history dating back to 2019

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2008, operating hours: 45,815 h, laser power: 5,000 W, sheet thickness steel (max.): 25 mm, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 115 mm, Included in the purchase: TruLaser 5030 Classic + LiftMaster L3030 + TruFlow 5000 TECHNICAL DETAILS Travel X-axis: 3,000 mm Travel Y-axis: 1,500 mm Travel Z-axis: 115 mm Laser power: 5,000 W Max. sheet thickness - mild steel: 25 mm Max. sheet thickness - stainless steel: 20 mm Max. sheet thickness - aluminium: 12 mm Giodpfx Ansy Iwl Tsxst Max. workpiece weight: 900 kg MACHINE DETAILS Control type: CNC Beam-on hours: 45,815 h Laser-on hours: 86,475 h Dimensions & Weight Dimensions (L x W x H): 11,100 x 4,600 x 2,400 mm Machine weight: 12,000 kg

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2009, operating hours: 18,649 h, laser power: 5,000 W, sheet thickness steel (max.): 25 mm, sheet thickness stainless steel (max.): 20 mm, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, TECHNICAL DETAILS Giedpfxey Iwmde Anxst Working area (L x W): 3,000 mm x 1,500 mm Laser power: 5,000 W Maximum sheet thickness, mild steel: 25 mm Maximum sheet thickness, stainless steel: 20 mm Maximum sheet thickness, aluminium: 12 mm MACHINE DETAILS Control type: CNC Operating hours NC ON: 38,900 h Operating hours laser ON: 39,498 h Operating hours beam ON: 18,649 h Machine weight: 12,000 kg

Condition: ready for operation (used), Year of construction: 2015, operating hours: 2,795 h, functionality: fully functional, machine/vehicle number: 400873, travel distance X-axis: 1,500 mm, travel distance Y-axis: 1,500 mm, pump power: 2,200 W, sheet thickness steel (max.): 120 mm, The machine was overhauled in 2026 and serviced every 500 operating hours! TECHNICAL DETAILS Working area X-axis: 1,500 mm Working area Y-axis: 1,500 mm Gedpfx Asy Nmtvenxjit Cutting capacity steel: 120 mm (recommended: 60 - 80 mm) Cutting capacity aluminium: 120 - 200 mm Cutting capacity plastic, stone etc.: unknown MACHINE DETAILS Pump output: 22 kW (30 HP) Last pump overhaul: 3 operating hours ago EQUIPMENT Spare parts Computer Water softening system

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2006, operating hours: 14,434 h, controller model: Siemens Sinumerik 840D, laser type: CO₂ laser, laser power: 3,200 W, Equipment: safety light barrier, TECHNICAL DETAILS Laser power: 3,200 W MACHINE DETAILS Control system: Siemens Sinumerik 840D Laser on hours: 14,434 h Giedpfx Aey Rk Uyenxot Power on hours: 39,875 h EQUIPMENT Closed machine frame with integrated laser unit Laser unit: CO2 laser TFL 3200 high-frequency unit, maintenance-free turbo radial blower, mirror telescope Automatic pallet changer Longitudinal conveyor belt for small parts / scrap Drives: Maintenance-free three-phase servo motors Additional highly dynamic Xp axis Quick-change cutting head system Laser cutting head with 5" lens and 7.5" lens Programmable cutting gas pressure adjustment APC capacitive height regulation and process control Automatic focus position adjustment AutoLas Plus Laser power control Positioning laser diode HI-LAS high-pressure cutting High-speed processing with SprintLAS ContourLAS for production of smaller holes PMS plasma sensing Automatic sheet outer edge detection Programmable power cycles Compressed air cutting PCS Process Control System Microweld Spray device for safe thick sheet processing Automatic shutdown Work area lighting Workshop programming ToPs 100 lite Control: Siemens Sinumerik 840D Open PC-based control, simple operation, online help, integrated E-Shop, diagnostic function, maintenance logbook, technology data, teleservice Safety equipment: Multi-beam light curtains, completely enclosed and ventilated beam guidance, monitoring system, multi-chamber extraction and compact deduster, protective cabin