Used Diavite Compact for sale (3,954)

Condition: used, Year of construction: 2018, Overview This atmospheric filling machine was manufactured by Alfatek in 2018 and is designed for filling 330 ml bottles with crown caps. The machine achieves an output of 800-1,000 bottles per hour and was last used for beer filling. Technical details  Filling principle: Atmospheric Output: 800-1,000 bottles/hour Bottle format: 330ml Capper: 26mm crown cap Nwsdev Rq Dpspfx Aa Djb

Condition: used, Year of construction: 2010, Overview  The Octopus film winder was built in Finland in 2010. The machine was in use at a mineral water company until recently and is already dismantled and immediately available.   Technical details   Speed of the motion sequences  Ring up/down 0.15 m/s  Ring rotation 18 rpm  Film insertion 4.5 m/s  Film: LLDE pre-stretched  Hold-down device  Pallet dimensions   ¼ EURO,  ½ EURO,   EURO,   1200 × 1000,   Max. height 2400 mm,   Min. height approx. 50 cm depending on the system settings  Dimensions  Length 2850 mm   Width 2150 mm   Height 3140 mm   Weight 1050 kg   Voltage: 3 × 400 VAC 50 Hz +N+earth  Air pressure 6 bar, 9 l/operating cycle  Njdpfxouca Amo Aa Djwb

Condition: used, Year of construction: 2011, operating hours: 938 h, machine/vehicle number: CE145628, Empty weight: 3.070 kg Lifting capacity: 350 kg Nwjdpsydhrhofx Aa Deb Working height: 1.400 cm Front tyres / undercarriage remaining: 60 Rear tyres remaining : 60 Tyre brand: - Transport dimensions (LxWxH): 2.5x1.2x2.7 Please contact PFEIFER GROUP for more information

Condition: used, Year of construction: 2011, operating hours: 304 h, machine/vehicle number: CE145603, Empty weight: 1.730 kg Lifting capacity: 350 kg Working height: 820 cm Front tyres / undercarriage remaining: 50 Rear tyres remaining : 50 Tyre brand: - Transport dimensions (LxWxH): 2.48x0.81x2.01 Njdjydhq Rspfx Aa Djwb Please contact PFEIFER GROUP for more information

Condition: used, Year of construction: 2008, operating hours: 1,188 h, machine/vehicle number: CE140920, Empty weight: 2.630 kg Lifting capacity: 300 kg Working height: 1.200 cm Front tyres / undercarriage remaining: 60 Nwjdpfxeydhqke Aa Dob Rear tyres remaining : 60 Tyre brand: - Transport dimensions (LxWxH): 2.45x1.2x1.53 Please contact PFEIFER GROUP for more information

Condition: used, Year of construction: 2011, operating hours: 690 h, machine/vehicle number: CE145089, Empty weight: 2.235 kg Lifting capacity: 450 kg Working height: 1.020 cm Front tyres / undercarriage remaining: 50 Rear tyres remaining : 50 Tyre brand: - Nsdpsydhqdsfx Aa Dowb Transport dimensions (LxWxH): 2.45x1.2x2.26 Please contact PFEIFER GROUP for more information

Condition: new, neu ca. 12 Wochen ab Auftrags Türkei 160788 € 3038.89 € 3 kW 12 mm 6 mm 6 mm 3 mm 6 mm 26,5 kW 250 mm 16 mm 160 x 160 mm 200 x 150 mm 6000 mm 58 kg/m +/- 0,2 mm +/- 0,05 mm rund, quadratisch, rechte 40 m/min 94 m/min 30 m/min 510 °/s The machine consists of the following components: - Encapsulated cutting room with protective glazing - CNC graphic control with touchscreen - Laser source Brilase 3 kW Premium incl. chiller - Cutting head with automatic focus adjustment - manual loading -manual unloading table 3 m - Positioning laser - Central lubrication - slug car - CAD/CAM software with autonesting - Work area lighting PRICE FCA TÜRKIYE OPTIONS: Suction unit with filters Nodswiqr Aspfx Aa Dswb Semi-automatic loading system Manual unloading table 6 m with conveyer Durma cloud license Lasersources with 4 or 6 kW on request

Condition: used, Year of construction: 2017, Industrial robot, training robot Manufacturer: Kuka Model: KR3 R540 KRC4 Compact Year of manufacture: 2017/2018 Low operating hours! Training cell, exhibition cell, demo cell: 800 mm x 1,000 mm Reach: 541 mm Weight: 26 kg Payload: 3 kg Kuka Controller KRC4 Compact KUKA.SystemSoftware KSS SR Nwsdpfewpg Ndjx Aa Dob Kuka SmartPad KCP4 Kuka connecting cable 4 m 22126ä

Condition: excellent (used), Year of construction: 2014, First commissioning: 2014 Control: Heidenhain iTNC 530 HSCI including HR 520 handwheel Machine hours Power-on hours: approx. 90,000 h Spindle hours: approx. 38,000 h Current milling spindle hours: approx. 900 h Travel distances X-axis: approx. 2,500 mm Y-axis: approx. 3,000 mm Z-axis: approx. 1,250 mm A-axis: ± 110° C-axis: ± 300° Clamping table Clamping surface: approx. 2,500 x 3,250 x 600 mm 2-axis milling head VH30 Spindle power: 60 kW Spindle speed: max. 22,000 rpm Torque: 95 Nm Tool holder: HSK 63A Tool clamping: hydraulic Coolant supply: external and internal Linear axis drives Feed speed X/Y/Z-axis: up to 60 m/min Axis acceleration X/Y/Z-axis: up to 5 m/s² Electrical specifications Connected load: 190 kVA Main fuse: approx. 315 A Dimensions, weights Space requirement (machine with peripherals): approx. 10,000 x 8,000 x 5,650 mm Total weight: approx. 63,000 kg Nwjdpfx Aewywcioa Dsb Colour Enclosure, portal, control cabinet: RAL 7035 light grey Milling head and applications: RAL 6038 luminous green Description: Additional equipment - Coolant supply with belt filter system - 50-position chain-type tool changer - Work area enclosure - Chip conveyor - Emulsion mist extraction system from LTA Optional at extra cost: - Renishaw RMP60 wireless measuring probe - BLUM Control NT Condition of the machine Fully functional, in excellent condition and available for inspection under power! Images are sample photos from a new machine of this type. Original images to follow shortly!

Condition: good (used), Year of construction: 2007, SCM Compact XL four-side planer - Italian production - year of production 2007 TECHNICAL PARAMETERS: planing width 230 mm planing height 120 mm 1) horizontal, lower 230 mm 5.5 kW 2) vertical right 130 mm 3) vertical left 130 mm (2nd and 3rd spindle) 11 kW 4) horizontal, top 230 mm 7.5 kW all spindles up / down, right / left spindle diameter 40 mm from the top 3 introducing rollers, metal, torsion, including 2 double top pulling roller, double rubber pressure 1 pc on the side a rubber pulling roller in the lower table top feed on cardan shafts pneumatic clamps smooth regulation of the feed speed 5-22 m / min 1.1 kW feed motor electric setting of the planing thickness 0.37 kW lifting motor Nwedpfshrdmiex Aa Dsb the length of the introducing table top 2470 mm locked in the cabin central lubrication of the table top diameter of the extraction nozzle 150 and 180 mm dimensions (length / width / height) 3650/1200/1600 mm weight approx. 1500 kg

Condition: excellent (used), Year of construction: 2011, Four Side Planer SCM Compact NTE - after the technical review - Italian production - year of production 2011 TECHNICAL PARAMETERS: planing width 240 mm planing height 130 mm spindle diameter 40 mm spindle speed 6000 rpm 1 lower spindle 3 kW 2 right spindle 7.5 kW 3 left spindle 5.5 kW 4 upper spindle 6 kW 5 lower spindle 5.5 kW six top pull rollers pneumatic pressure adjustable feed on the inverter feed speed range 5-25 m / min adjustable heads table top length 2480 mm electric brakes nozzles diameter 2 x 180 mm and 2 x 150 mm dimensions of the machine (length / width / height) 340/160/170 cm weight 2480 kg Njdpfx Aogyflcsa Dswb

Condition: used, Year of construction: 2019, CNC portal plasma cutting machine Manufacturer: Microstep Model: MasterCut Compact 4001.20Ptk Year of manufacture: 2019 CNC control Working area: 2 x 4 m '”MasterCut” plasma rotator with fully automatic support for weld seam preparation 1 plasma torch with Kjellberg HiFocus 280i power source Nwsdpsxnmbnjfx Aa Djb TEKA filtration system ä21126

Condition: used, Applicable material: Concrete A POLYGONMACH PCC60 60 M3 compact concrete batching plant, if high quality and well designed, can provide users with many advantages: 1. Thanks to its high production capacity, it provides a fast supply of concrete used in large and complex construction projects. 2. Depending on its technical characteristics, especially mold, pump, etc. When used, it simplifies the concrete pouring works and speeds up the works without sacrificing quality. 3. Thanks to the automatic control systems, the concrete quality is ensured at a consistently high level. This ensures excellent results in construction projects. 4. Thanks to its compact design, it takes up little space and is easy to transport, install and disassemble. Thus, users can quickly move these exchanges from one place to another. 5. With energy efficient and environmentally friendly design options, operating costs are lowered, thereby saving more money for users. 6. If properly cared for, it is long lasting and generally delivers a high quality product. Because of all this, a high-quality and well-designed compact concrete batching plant with a capacity of 60 M3 is preferred by construction companies and contractors. A POLYGONMACH 60 M3 compact concrete batching plant can use different types of additives, cements and aggregates depending on its type and properties. These factors determine the desired properties of concrete. Nwedex D A Ayspfx Aa Dsb Cement: The cements generally used in concrete batching plants are ordinary ported cements, blast furnace slag cements and reactive powder additive cements. These different types of cement can change various properties of concrete. Mobility: stationary Other characteristics: compact, automatic Capacity: 60 m³/h(2,118.88 ft³/h)

Condition: reconditioned (used), Year of construction: 2015, functionality: fully functional, overall weight: 22,000 kg, power: 375.1 kW (509.99 HP), year of last overhaul: 2024, Diesel engine: 510 HP Fine shredding basket; hole-size can be agreed. Foldable discharge conveyor Overband magnet Central lubrication Twin-drive (separate drives for infeed roller and scraper floor) Hydraulically self propelled drive (for moving on site) Nwedpferrg Ifsx Aa Deb Radio remote control We can also offer financing if required.

Condition: used, Year of construction: 1991, Compact separator with cartridge filter Njdpfjwkwknsx Aa Dowb Manufacturer: Keller Lufttechnik Model: Uni-Star FV Year of manufacture: 1991 For dust extraction Motor power: 3.3 kW

Condition: good (used), PLC controller, central assembly, working memory, CPU, central unit, central processing unit, compact unit, compact CPU Nwedpfx Aasycgdge Djb -Manufacturer: Siemens, Compact device CPU 214 -Type: 6ES7214-1AC01-0XB0 /6ES7 214-1AC01-0XB0 -Quantity: 1 module available -Dimensions: 200/80/H65 mm -Weight: 0.4 kg

Condition: used, Year of construction: 2008, cutting diameter / mm saw band length / mm cutting width / mm including roller conveyor 4000 x 500 x 850 mm Sawing diameter (round): 260 mm Sawing diameter (square): 260 mm Sawing diameter (rectangular): 300 x 260 mm Saw blade dimensions: 4200 x 34 x 1.1 mm High-performance band saw automatic machine, heavy-duty hydraulic production band saw Parallel sawing feed system in profile guide rails Mitsubishi NC program control E1032 for preselection of 90 sets, each with a specific quantity and corresponding cut length PLC control Mitsubishi With Siko incremental encoder Material feed with ball screw spindle 950 mm in one stroke, any desired cut length from 3 mm – 9999 mm Nwsdpfewm Rqtex Aa Dsb Hydraulic material clamping with long-stroke cylinder, opening on both sides Material clamping with double vice in front of and behind the saw blade Remaining piece length in automatic mode: 90 mm Max. cutting length in automatic mode: unlimited Material support height: 850 mm Net weight: 2300 kg Dimensions W x H x D mm: 2580 x 2000 x 2000

Condition: ready for operation (used), AUTOMATIC PALLET STRECH WRAPING MACHINE - PALLETIZER OCTOPUS COMPACT Nwodpfxeyb H Hfo Aa Dob MADE BY HALOILA, FINLAND 30 PALLET PER HOUR VERY GOOD CONDITION VIDEO ATTACHED

Condition: new, functionality: fully functional, Year of construction: 2025, operating hours: 30 h, Equipment: centralized greasing system, dust extraction, emergency stop, fume extraction, safety light barrier, Tube Laser Cutting System Ideal for Entry-Level Applications. Simplicity meets efficiency with the Durma HD-TC COMPACT 60250 entry-level tube laser. Perfect for workshops, metal fabricators, and others looking to step into tube laser processing, this laser offers straightforward operation, reliable performance, and excellent value for money. Discover how the Durma HD-TC COMPACT 60250 can enhance your production with precise cuts and user-friendly technology, adding value to your operation. 3 kW Laser Power Maximum Sheet Thicknesses: - Mild Steel: 12 mm - Stainless Steel: 6 mm - Aluminium: 6 mm - Copper: 3 mm - Brass: 6 mm Capacity: - Maximum Tube Diameter: Ø250 mm - Maximum Square Profile Dimensions: 160x160 mm - Maximum Rectangular Profile Dimensions: 200x150 mm - Minimum Tube Diameter: 16 mm - Maximum Material Length: 6000 mm - Minimum Remnant Length: 65 mm Nwsdpfx Aasrkntco Dsb - Unloading Length: 3000 mm - Semi-automatic unloading unit: optional (6m) - Maximum Material Weight: 58 kg/m - Maximum Total Workpiece Weight: 350 kg - Profile types that can be cut: Round, square, rectangular, elliptical - Open profile types that can be cut: I, C, L - Maximum open profile dimensions: 240x240 mm Dynamics: - X-Axis: 40 m/min - Y-Axis: 94 m/min - Z-Axis: 30 m/min - A-Axis: 510 °/s Accuracy: - Positioning Accuracy: ±0.2 mm - Positioning Variation: ±0.05 mm - Tube Center Detection with Capacitive Sensor: Yes Additional Available Configurable Options. LASER POWER: - Upgrade to DURMA LASER SOURCE BRILASE 4 kW ADVANCED fiber laser source (incl. chiller) + Durma cutting head - Upgrade to DURMA LASER SOURCE BRILASE 6 kW ADVANCED fiber laser source (incl. chiller) + Durma cutting head OPTIONS: - Air filtration system (40 bar N₂ + 16 bar O₂ + 16 bar Air) - Air filtration system (40 bar N₂ + 16 bar O₂ + 40 bar Air) - CNC oscillating head (+/- 45°) - Semi-automatic front loading system - Unloading table (6m) with conveyor - Unloading table (3m) with conveyor - Additional dongle software - Transformer 220, 440, 575V SOFTWARE OPTIONS: - Durma Cloud License + D-Mobile + Smart Watch - STEP file importer

Condition: new, Year of construction: 2026, CORMAK LUFT 1500 VSD+PM Compact screw compressor with dryer – compact set for demanding applications – ENERGY SAVER SET INCLUDES: LUFT 1500 VSD+PM COMPACT screw compressor with dryer. Horizontal compressed air receiver 500 L. Key features that distinguish these models: 1. Permanent Magnet (PM) Motor Technology Most Energy Saver compressors use Permanent Magnet motors. Unlike standard induction motors: They achieve efficiency levels compliant with IE4 or even IE5 standards. They maintain high efficiency even at very low speeds, where standard motors lose performance. They are smaller, lighter and generate less heat. 2. Advanced Inverter Control (VSD) The core of the Energy Saver line is a frequency converter (inverter). Demand matching: The compressor does not operate on an “all-or-nothing” basis. If your system requires only 30% capacity, it reduces speed accordingly, consuming proportionally less energy. Elimination of idle operation: Conventional compressors often run unloaded for several minutes after filling the tank, consuming around 25–30% of rated power without producing air. Energy Saver models virtually eliminate this loss. 3. Soft Start Thanks to the inverter, these units start smoothly from 0 Hz, eliminating current surges at start-up, which: Protects the plant’s electrical installation. Allows frequent start-stops without overheating the windings. 4. Real Savings In practice, Energy Saver technology reduces electricity bills by 30% to 50% compared with fixed-speed compressors. It also maintains very stable network pressure (within 0.1 bar), essential for precision equipment such as laser cutters. Extended service life: Smooth pressure and temperature changes prolong screw element life. Technical Parameters Motor power 11 kW / 15 HP Voltage 400V / 50Hz Output 0–6 bar 1620 L/min Output at 6 bar 1580 L/min Output at 8 bar 1350 L/min Output at 10 bar 1230 L/min Nedsychbaepfx Aa Dowb Outlet connection (G) 1" Dimensions 1600 × 740 × 1750 mm Weight 500 kg

Condition: new, Year of construction: 2026, functionality: fully functional, CORMAK LUFT 1000 VSD+PM Compact Screw Compressor with Dryer – Compact Set for Demanding Applications – ENERGY SAVER SET INCLUDES: LUFT 1000 VSD+PM COMPACT screw compressor with dryer Horizontal compressed air tank – 500 L Key Features That Distinguish These Models 1. Permanent Magnet (PM) Motor Technology Most compressors in the Energy Saver series use permanent magnet motors. Compared to standard induction motors, they: Achieve efficiency levels compliant with IE4 or even IE5 standards Maintain high efficiency even at very low rotational speeds (standard motors lose efficiency outside their nominal range) Are smaller, lighter, and generate less heat 2. Advanced Variable Speed Drive (VSD) Control The core of the Energy Saver line is the frequency inverter (VSD). Demand-based operation: The compressor does not operate in an “all-or-nothing” (load/unload) mode. If your system requires only 30% capacity, the compressor reduces its speed and consumes proportionally less energy. Elimination of idle running: Traditional compressors often continue running for several minutes after the tank is filled, consuming approx. 25–30% of nominal power without producing air. Energy Saver models almost completely eliminate this energy loss. 3. Soft Start Thanks to the inverter, these units start smoothly from 0 Hz. This means no sudden current surges during startup, which: Protects the electrical installation in the facility Allows frequent start/stop cycles without the risk of winding overheating Njdpfx Aajycg Ufs Dewb 4. Real Energy Savings In practice, the Energy Saver series can reduce electricity costs by 30% to 50% compared to traditional fixed-speed compressors. Additionally, the system maintains very stable pressure in the air network (with accuracy up to 0.1 bar), which is crucial for precision equipment such as laser cutting machines. Extended service life: The absence of sudden pressure and temperature spikes significantly extends the lifespan of the screw element. Technical Specifications Motor power: 7.5 kW / 11 HP Voltage: 400V / 50Hz Air delivery at 0–6 bar: avg. 990 L/min Air delivery at 6 bar: 990 L/min Air delivery at 8 bar: 950 L/min Air delivery at 10 bar: 950 L/min Outlet connection (G): 3/4" Dimensions: 1495 × 600 × 1600 mm Weight: 350 kg

Condition: new, Year of construction: 2026, functionality: fully functional, CORMAK LUFT 1000 VSD+PM Compact Screw Compressor with Dryer – Compact Package for Demanding Applications – ENERGY SAVER SET INCLUDES: LUFT 1000 VSD+PM COMPACT screw compressor with dryer Horizontal compressed air tank – 270 L Key Features of the Energy Saver Series 1. Permanent Magnet (PM) Motor Technology Most compressors in the Energy Saver series use permanent magnet motors. Compared to standard induction motors, they: Achieve efficiency levels of IE4 or even IE5 Maintain high performance even at very low speeds (standard motors lose efficiency outside their nominal range) Are smaller, lighter, and generate less heat 2. Advanced VSD Inverter Control The heart of the Energy Saver line is the frequency inverter (VSD). Adaptation to demand: The compressor does not operate on an "all-or-nothing" principle (load/unload). If your system requires only 30% capacity, the compressor reduces speed, consuming proportionally less energy. Eliminates idle running: Traditional compressors often run for several minutes after the tank is full, consuming about 25–30% of nominal power without producing air. Energy Saver models nearly eliminate this wasteful process. 3. Soft Start Thanks to the inverter, these units start smoothly from 0 Hz. This means no sudden current surges during startup, which: Saves the electrical installation in the facility Nodpfxeycg Tne Aa Dewb Allows frequent start/stop cycles without overheating the windings 4. Real Energy Savings In practice, the Energy Saver series can reduce electricity costs by 30% to 50% compared to traditional fixed-speed compressors. Additionally, the system maintains very stable pressure in the network (with accuracy up to 0.1 bar), which is crucial for precision devices such as laser cutters. Longer service life: No sudden pressure and temperature spikes prolong the screw stage life. Technical Specifications Motor power: 7.5 kW / 11 HP Voltage: 400V / 50Hz Air delivery at 0–6 bar: avg. 990 L/min Air delivery at 6 bar: 990 L/min Air delivery at 8 bar: 950 L/min Air delivery at 10 bar: 950 L/min Outlet connection (G): 3/4" Dimensions: 1495 × 600 × 1440 mm Weight: 290 kg

Condition: new, Year of construction: 2026, CORMAK LUFT 700 VSD+PM Compact Screw Compressor with Dryer – Compact Package for Demanding Applications – ENERGY SAVER SET INCLUDES: LUFT 700 VSD+PM COMPACT screw compressor with dryer Horizontal compressed air tank – 500 L Key Features of the Energy Saver Series 1. Permanent Magnet (PM) Motor Technology Most compressors in the Energy Saver series use permanent magnet motors. Compared to standard induction motors, they: Achieve efficiency levels of IE4 or even IE5 Maintain high performance even at very low speeds (standard motors lose efficiency outside their nominal range) Are smaller, lighter, and generate less heat 2. Advanced VSD Inverter Control The heart of the Energy Saver line is the frequency inverter (VSD). Adaptation to demand: The compressor does not operate on an "all-or-nothing" principle (load/unload). If your system requires only 30% capacity, the compressor reduces speed, consuming proportionally less energy. Eliminates idle running: Traditional compressors often run for several minutes after the tank is full, consuming about 25–30% of nominal power without producing air. Energy Saver models nearly eliminate this wasteful process. 3. Soft Start Thanks to the inverter, these units start smoothly from 0 Hz. This means no sudden current surges during startup, which: Saves the electrical installation in the facility Allows frequent start/stop cycles without overheating the windings 4. Real Energy Savings In practice, the Energy Saver series can reduce electricity costs by 30% to 50% compared to traditional fixed-speed compressors. Additionally, the system maintains very stable pressure in the network (with accuracy up to 0.1 bar), which is crucial for precision devices such as laser cutters. Longer service life: No sudden pressure and temperature spikes prolong the screw stage life. Technical Specifications Motor power: 5.5 kW / 7.5 HP Voltage: 400V / 50Hz Air delivery at 0–6 bar: avg. 690 L/min Air delivery at 6 bar: 690 L/min Air delivery at 8 bar: 650 L/min Air delivery at 10 bar: 650 L/min Nwodpfxoycg Rys Aa Dsb Outlet connection (G): 1/2" Dimensions: 1840 × 640 × 1470 mm Weight: 320 kg

Condition: new, Year of construction: 2026, CORMAK LUFT 700 VSD+PM Compact Screw Compressor with Dryer – Compact Package for Demanding Applications – ENERGY SAVER SET INCLUDES: LUFT 700 VSD+PM COMPACT screw compressor with dryer Horizontal compressed air tank – 270 L Key Features of the Energy Saver Series 1. Permanent Magnet (PM) Motor Technology Most compressors in the Energy Saver series use permanent magnet motors. Compared to standard induction motors, they: Achieve efficiency levels of IE4 or even IE5 Nwodpfxeycg I Ss Aa Dob Maintain high performance even at very low speeds (standard motors lose efficiency outside their nominal range) Are smaller, lighter, and generate less heat 2. Advanced VSD Inverter Control The heart of the Energy Saver line is the frequency inverter (VSD). Adaptation to demand: The compressor does not operate on an "all-or-nothing" principle (load/unload). If your system requires only 30% capacity, the compressor reduces speed, consuming proportionally less energy. Eliminates idle running: Traditional compressors often run for several minutes after the tank is full, consuming about 25–30% of nominal power without producing air. Energy Saver models nearly eliminate this wasteful process. 3. Soft Start Thanks to the inverter, these units start smoothly from 0 Hz. This means no sudden current surges during startup, which: Saves the electrical installation in the facility Allows frequent start/stop cycles without overheating the windings 4. Real Energy Savings In practice, the Energy Saver series can reduce electricity costs by 30% to 50% compared to traditional fixed-speed compressors. Additionally, the system maintains very stable pressure in the network (with accuracy up to 0.1 bar), which is crucial for precision devices such as laser cutters. Longer service life: No sudden pressure and temperature spikes prolong the screw stage life. Technical Specifications Motor power: 5.5 kW / 7.5 HP Voltage: 400V / 50Hz Air delivery at 0–6 bar: avg. 690 L/min Air delivery at 6 bar: 690 L/min Air delivery at 8 bar: 650 L/min Air delivery at 10 bar: 650 L/min Outlet connection (G): 1/2" Dimensions: 1495 × 520 × 1340 mm Weight: 250 kg

Condition: new, functionality: fully functional, power: 18.39 kW (25.00 HP), gearing type: automatic, fuel type: diesel, color: red, overall weight: 1,870 kg, lifting power: 700 kg/m, lifting height: 2,825 mm, tire size: 26 x 12.00 - 12, tire condition: 100 %, drive condition: 100 %, axle configuration: 2 axles, number of seats: 1, emission class: euro5, mast type: telescopic, digging bucket width: 120 mm, Year of construction: 2025, Equipment: additional headlights, head guard, standard shovel, trailer coupling, The H&R 1607T telehandler is our smallest loader with a cab. It is exceptionally maneuverable and can be used wherever space is limited. With a lifting capacity of 700 kg, the H&R 1607T telehandler lifts loads weighing up to 700 kg to a height of 2.82 m (bottom edge of the standard pallet fork). Thanks to the standard wide tires, it is very stable and safe. Nwjdpfov Tabisx Aa Dob The new 3-cylinder Perkins Turbo engine (Mannheim, Germany) meets the Euro 5 standard even without a particulate filter and is particularly efficient. With the 2-speed hydrostatic drive, the 1607 loader reaches a top speed of approximately 16 km/h and is comfortable to drive. The additional 3rd and 4th hydraulic control circuits allow for the use of various attachments. The hydraulic quick coupler allows for quick and convenient changing of front-mounted tools. H&R loaders are technically and visually optimized in-house and thoroughly tested. In addition, each machine receives extensive rust protection treatment. Our loaders are CE-compliant according to the EU Machinery Directive. Our machine has a TÜV Süd certificate for obtaining an individual operating permit in accordance with Section 21 of the German Road Traffic Licensing Regulations (StVZO) (road approval/operating permit as a self-propelled work machine). Key Features of the H&R 1607T Skid Steer Loader • Fully equipped • Extensively optimized in Germany • Telescopic boom for extended reach • Ideal for tight work environments • Includes standard 120cm bucket and pallet forks • Comfortable cab with heating, ventilation, and radio (USB/MP3) • Hydraulic quick coupler • Joystick control with float position • Electric gear on the joystick • Auxiliary hydraulics for front-mounted tools • Hydraulic oil cooler • Rotating beacon • LED work lights front and rear • Wide tires 26 x 12.00-12 • Adjustable steering column • Hour meter and fuel gauge • Trailer hitch ball head • CE compliant according to the EU Machinery Directive • 1-year spare parts warranty Price Net: €19,290.00 VAT: €3,665.10 Gross: €22,955.10 Financing available! Optional 2-year warranty €595 TÜV (road approval) €870 Transport within Germany and Austria for an additional charge Please provide us with your address; we will be happy to provide you with a free, non-binding quote. Technical specifications Lifting capacity: 700 kg Lifting height: 2825 mm (bottom edge of standard pallet fork) Unloading height: 2383 mm (bottom edge of standard bucket tipped out) Lift time / Lowering time: 4.0 / 3.5 seconds Engine: Perkins 3-cylinder diesel Power: 25 HP Emissions class: Euro 5 Drive: Hydrostatic (PWG) All-wheel drive, speed approx. 16 km/h Dimensions: 2964 x 1160 x 2340 mm Weight: 1740 kg Standard tires: 26 x 12.00-12 Accessories and spare parts are not included. Available from us. Please provide your phone number when making inquiries!