Used Plastic Injection Moulder for sale (7,516)

Condition: excellent (used), Year of construction: 2021, operating hours: 3,300 h, functionality: fully functional, machine/vehicle number: ADKL2001, clamping force: 14,000 kN, screw diameter: 120 mm, clearance between the columns: 1,450 mm, column diameter: 240 mm, displacement volume: 7,351 cm³, injection pressure: 1,200 bar, injection weight: 6,983 g, mold height (min.): 650 mm, ejector force: 3,50,000 N, ejector stroke: 380 mm, opening stroke: 1,450 mm, plate length: 2,950 mm, plate width: 2,000 mm, plate height: 2,000 mm, total length: 14,100 mm, total width: 3,400 mm, total height: 3,600 mm, overall weight: 75,000 kg, heating capacity: 60 kW (81.58 HP), pressure: 178 bar, number of injections: 1, pump power: 2,04,000 W, power: 266 kW (361.66 HP), type of input current: three-phase, input frequency: 50 Hz, input voltage: 400 V, input current: 520 A, Equipment: documentation/manual, The machine has seen limited use and is in very good condition. It has been well maintained. The machine only processes ABS and PP. It features a Beckhoff control system. The machine is equipped with extensive additional equipment, including 3 pneumatic valves, two hydraulic valves, a servo valve for table movement hydraulics, 32 tool heating zones, a water manifold with 8 zones, a screw heating element insulation, a hydraulic screw rotation system for torpedo replacement, a torpedo with a locking system, an interchangeable centering ring, a Euro-map for the robot, a door with automatic opening via an electric motor, and an electrical cabinet with sockets. Additionally, water blocks are installed on both the moving and stationary tables, each with 8 connections. Furthermore, a set of spare parts is included, such as a complete torpedo, a screw nozzle, heaters, temperature probes, and specific hydraulic seals, as well as a self-filtration filter and a torpedo wrench, and auxiliary ejector rods. A Wemo robot can also be sold with the machine; while it is not the subject of this advertisement, it can be purchased separately and added to the machine. It was used with the machine and is adapted for it. Tsdpfx Ajzna T Roired

Condition: ready for operation (used), Year of construction: 2007, operating hours: 39,807 h, functionality: fully functional, machine/vehicle number: 5347, clamping force: 6,500 kN, screw diameter: 85 mm, clearance between the columns: 920 mm, column diameter: 920 mm, injection pressure: 2,000 bar, injection weight: 2,600 g, ejector force: 180 N, ejector stroke: 250 mm, opening stroke: 920 mm, total length: 8,870 mm, total width: 2,100 mm, total height: 2,550 mm, overall weight: 32,500 kg, heating capacity: 39 kW (53.03 HP), power: 75 kW (101.97 HP), input voltage: 400 V, Equipment: documentation/manual, For sale is a PLASTIC METAL UNYKA 650 injection molding machine with a clamping force of 6,500 kN (650 tons). The machine is currently in operation and therefore in functional condition. It is available immediately. Technical data: Manufacturer: PLASTIC METAL S.p.A. Type: UNYKA 650 Year of manufacture: 2007 Clamping force: 6,500 kN (650 tons) Machine weight: approx. 32,500 kg Drive power: 75 kW Heating power: 39 kW EUROMAP: 6500H/4165 Serial number: 5347 The machine is currently still in production and can be inspected and demonstrated on-site after prior arrangement. Todpjzza Egefx Aired Inspection is only possible after prior arrangement. Loading & Collection The machine can be loaded directly on-site after production ends. Loading with an overhead crane is possible. Sale without peripheral equipment. The machine is offered without peripheral equipment. Dismantling, transport, and further processing will be arranged. Availability: immediately If you are interested or would like to arrange an inspection appointment, we look forward to receiving your inquiry.

Condition: used, Year of construction: 2005, functionality: fully functional, machine/vehicle number: MST-0800C0028, For sale: automatic plastic injection molding machine ATEC HQ-800QL. Year of manufacture – 2005 (04), Serial No. MST-0800C0028. Hydraulic system with digital control panel, suitable for serial production of plastic parts. Power supply 380 V, 50 Hz, 3 phases. Used, fully equipped, previously operated in production. Suitable for manufacturing technical, packaging, and industrial plastic components. Inspection on site possible. Todpjx Nhy Refx Airsd

Condition: used, Injection molding machine ARBURG, Type Allrounder 320 C 600-100 Serial No. 189356, Year of manufacture 09/2002 Clamping force 60 tons Screw diameter 25 mm Dosing volume max. 49 cm3 Injection pressure max. 1570 bar Opening stroke - platen stroke max. 350 mm Platen dimensions 446 x 446 mm Tie bar spacing 320 x 320 mm Mold height min.: 200 mm Platen spacing min.: 200 mm Platen spacing max.: 550 mm Centering of fixed and moving platens 125 mm Heater power 4.9 kW Motor power hydraulic pump 15 kW Mains connection 400 Volt, 50 Hz, 19.9 kW - Machine control SELOGICA - Two controllable hydraulic circuits for core pullers - Injection unit with COLORTRONIC material hopper for automated granule feed - U-version interface - HHG interface - Control ARBURG MULTRONICA with foil keypad and integrated display - 88790 operating hours recorded (power-on hours) - 44925 operating hours of the hydraulic pump (hydraulic on) - Control cabinet fixed to the machine - Work area protective doors at the front and rear, manually sliding with safety switches - Mobile control panel with function keys, mounted on the back of the machine Space requirement L x W 3650 x 1700 mm Height with material hopper 2200 mm Weight 3000 kg Tsdpezqglrofx Airsd Good condition

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, machine/vehicle number: 161394, clamping force: 6,500 kN, screw diameter: 90 mm, injection weight: 2,254 g, overall weight: 33,000 kg, TECHNICAL DETAILS Clamping Unit Clamping force: 6,500 kN Horizontal column spacing: 1,025 mm Vertical column spacing: 930 mm Tool height: min. 450 mm Tool height: max. 950 mm Opening stroke: max. 1,800 mm Injection Unit Screw diameter: 90 mm Todpe Afw Hysfx Airsd Injection volume: 2,480 cm³ Injection weight: 2,254 g MACHINE DETAILS Rated power of the pump motor: 55 kW Heating capacity: 62 kW Dimensions & Weight Dimensions (L x W x H): approx. 8,300 x 2,500 x 2,330 mm Machine weight: approx. 33,000 kg

Condition: excellent (used), Year of construction: 2008, DEMAG System 1500/1500-16000 injection molding machine Wittmann W753C robot Year of manufacture: 2008 Clamping force: 15,000 kN (1,500 tons) TECHNICAL SPECIFICATIONS 1. Basic data - Manufacturer: DEMAG Tedps Af Id Hsfx Airod - Model: System 1500/1500-16000 - Year of manufacture: 2008 - Clamping force: 15,000 kN (1,500 tons) - Injection unit: 16000 - Additional equipment: Wittmann W753C linear robot 2. Clamping unit - Clamping force: 15,000 kN (1,500 tons) - Mounting plate dimensions (H × V): 2,150 × 1,880 mm - Column spacing (H × V): 1,500 × 1,250 mm - Minimum mold height: 700 mm - Maximum mold height: 1,400 mm - Maximum opening: 2,900 mm 3. Plasticizing unit and injection unit - Injection unit: 16000 - Screw diameter: 145 mm - Injection volume: 10,981 cm³ - Injection shot weight (PS): 9,880 g - Maximum injection pressure: 1,454 bar 4. Hydraulic and electrical system - Rated power of the pump motor: 165 kW - Heater power: 97 kW 5. Machine dimensions and weight - Length: 14,400 mm - Width: 3,400 mm - Height: 2,900 mm - Net machine weight: 74,000 kg (74 tons) - Weight of the additional unit identified in the documentation as the control cabinet: 21,000 kg (21 tons) - Total weight according to the provided data: approximately 95,000 kg (95 tons)

Condition: used, Injection molding machine ARBURG, type Allrounder 221 M 350-75 Serial No. 163646, Year of manufacture 1995 Clamping force 35 tons (350 kN) Screw diameter, presumably Ø 25 mm Platen size 342 x 250 mm Mold size, max. 221 mm Mold mounting height 150 to 300 mm Column spacing 221 mm (center distance) Opening stroke - platen stroke, max. 200 mm Ejector stroke 60 mm Ejector force 27 kN Hydraulic oil tank capacity 120 liters (delivery without oil) Heating capacity 4 kW Motor power, hydraulic pump 7.5 kW Power supply 400 volts, 50 Hz, 12 kW Tjdezx Etwepfx Aired - ARBURG MULTRONICA control system with foil keyboard and screen - Stainless steel granulate hopper, 50 liters, on the injection unit - Adjacent control cabinet Space requirement without transport pallet, L x W x H 2750 x 1350 x 1850 mm Transport dimensions on pallet, L x W x H 2750 x 1700 x 1900 mm Weight approx. 1300 kg Good condition

Condition: excellent (used), Year of construction: 2007, KraussMaffei KM 950-17200 MX injection molding machine Year of manufacture: 2007 Clamping force increased to 1,000 tons (10,000 kN) TECHNICAL SPECIFICATIONS 1. Clamping unit - Clamping system: fully hydraulic - Clamping force: 10,000 kN (1,000 tons) – increased from the factory standard of 950 tons - Opening force: 665 kN - Column spacing (H × V): 1,400 × 1,150 mm - Dimensions of mounting plates: 1,960 × 1,710 mm - Opening stroke: 1,900 mm - Minimum mold height: 500 mm - Maximum mold height: 1,200 mm - Maximum mold opening: 2,400 mm - Ejector stroke: 300 mm 2. Plasticizing unit - Complete plasticizing unit for thermoplastics Tjde Af Hxxepfx Airod - High-performance HPS-UN screw - Screw diameter: 120 mm - Nozzle radius: 30 mm - Nozzle orifice diameter: 12 mm 3. Injection unit - Screw diameter: 120 mm - Injection weight (HDPE): 5,420 g - Injection volume: 7,634 cm³ - Specific injection pressure: 2,257 bar 4. Control system - Control system based on an industrial computer - Integrated operator panel - Color touchscreen 5. Machine dimensions and weight - Length: 12,770 mm - Width: 3,420 mm - Height: 2,750 mm - Total weight: 61,500 kg (61.5 tons)

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, machine/vehicle number: 42503, clamping force: 4,000 kN, screw diameter: 70 mm, injection pressure: 1,481 bar, injection weight: 1,040 g, overall weight: 5,600 kg, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Clamping unit Clamping force: 4,000 kN Platen length: 1,300 mm Platen width: 1,080 mm Tool height: min. 350 mm Mold opening: max. 1,300 mm Injection unit Screw diameter: 70 mm Injection volume: 1,155 cm³ Injection weight: 1,040 g Injection pressure: 1,481 bar Todpfx As Afw Dreirjd MACHINE DETAILS Rated power of the pump motor: 45 kW Dimensions & Weight Dimensions (L x W x H): approx. 8,000 x 2,250 x 2,200 mm Machine weight: approx. 5,600 kg

Condition: excellent (used), Year of construction: 2007, KRAUSSMAFFEI KM 800-12000 MX Injection Molding Machine - Year of manufacture: 2007 - Machine serial number: 61009705 - Clamping force: 8,000 kN (800 tons) - Machine type: hydraulic, two-platen injection molding machine - Control system: KraussMaffei MC5 2. Clamping System - Clamping system: hydraulic-mechanical, two-platen - Design: 4 pressure pads and 4 locking units on the moving platen - Clamping force: 8,000 kN (800 tons) - Dimensions of mounting platens (H × V): 1,600 × 1,530 mm - Column spacing (H × V): 1,120 × 1,000 mm - Minimum mold height: 500 mm - Maximum mold height: 1,100 mm - Maximum opening stroke: 2,600 mm 3. Plasticizing System - Complete plasticizing system for thermoplastics - Injection unit: 12000 - Screw diameter: 135 mm - Check valve: yes - Nozzle: open - Injection unit adjustment: PV 4. Injection Unit - Screw diameter: 135 mm - Injection volume: 8,588 cm³ - Injection shot weight: 7,815 g - Maximum injection pressure: 1,389 bar 5. Hydraulic and Electrical System - Rated power of pump motor: 132 kW - Heater power: 90 kW - Operating voltage: 380 V - Power supply: three-phase - Frequency: 50 Hz - Rated current of circuit 1: 255 A - Rated current of circuit 2: 318 A - Main fuse for circuit 1: 315 A Todpfx Aj Af Ib Usirsd - Main fuse for circuit 2: 400 A 6. Control System - KraussMaffei MC5 control system - Color operator monitor - Integrated control panel - USB data carrier support - Adjustment of injection process parameters 7. Machine Dimensions and Weight - Length: 11,720 mm - Width: 2,920 mm - Height: 2,650 mm - Net weight including control cabinet: approximately 50,000 kg (50 tons)

Condition: excellent (used), Year of construction: 2004, ENGEL DUO 11050/2300 injection molding machine Manufacturer: ENGEL Model: DUO 11050/2300 Year of manufacture: 2004 Operating hours: 70,029 hours Clamping force: 23,000 kN / 2300 tons Screw diameter: 135 mm Injection volume: 8870 cm³ Control system: ENGEL Type: hydraulic, two-platen, large-size injection molding machine CLAMPING UNIT Clamping force: 23,000 kN (2300 tons) Dimensions of mounting plates: 2900 × 2500 mm Column spacing (H × V): 2000 × 1600 mm Minimum mold height: 700 mm Maximum mold height: 1890 mm Maximum distance between plates: 3800 mm Clamping system: hydraulic, two-platen INJECTION UNIT Injection unit: 11050 Screw diameter: 135 mm Injection volume: 8870 cm³ Injection shot weight (PS): 8071 g Maximum injection pressure: 1600 bar Screw replaced in 2011 Reinforced plasticizing unit, adapted for processing special materials ADDITIONAL EQUIPMENT Magnetic mold clamping system – functional 2 hydraulic cores 36 mold heating zones / hot runner channels 10 hydraulic cascades Mold tilting function ENGEL control system Tsdo Af Nkhopfx Aired Robot: none MAGNETIC MOLD CLAMPING SYSTEM The injection molding machine is equipped with functional magnetic plates for quick clamping of injection molds. The system reduces machine changeover time and facilitates the exchange of large and heavy molds, making it an important piece of additional equipment for an injection molding machine of this class. TRANSPORT DIMENSIONS AND WEIGHT Weight of main unit: approx. 113,000 kg Weight of control cabinet and additional components: approx. 18,000 kg Total approximate weight: approx. 131,000 kg (131 tons)

Condition: excellent (used), Year of construction: 2013, KRAUSSMAFFEI KM 1600-17200 MX Blu Power Injection Molding Machine Year of manufacture: 2013 Clamping force: 16,000 kN (1,600 tons) Control system: KraussMaffei MC6 TECHNICAL SPECIFICATIONS 1. Basic data - Manufacturer: KraussMaffei - Model: KM 1600-17200 MX Blu Power - servo - Year of manufacture: 2013 - Machine type: hydraulic injection molding machine for processing thermoplastic materials - Clamping system: fully hydraulic - Clamping force: 16,000 kN (1,600 tons) - Injection unit: 17200 - Control system: KraussMaffei MC6 2. Clamping unit - Clamping force: 16,000 kN (1,600 tons) - Opening force: 1,120 kN Tedpfx Aio Af I U Nerod - Dimensions of the mounting plates (H × V): 2,550 × 2,100 mm - Column spacing (H × V): 1,870 × 1,420 mm - Opening stroke: 2,700 mm - Minimum mold height: 700 mm - Maximum mold height: 1,600 mm - Maximum daylight: 3,400 mm - Ejector stroke: 350 mm - Ejector force (forward / backward): 300 / 150 kN 3. Plasticizing unit - Complete plasticizing unit for thermoplastics - Screw diameter: 135 mm - Screw length ratio L/D: 23 - Plasticizing unit in abrasion-resistant version - Screw check valve - Open nozzle 4. Injection unit - Injection unit type: 17200 - Screw diameter: 135 mm - Injection volume: 9,662 cm³ - Injection shot weight (PE): 6,860 g - Maximum injection pressure: 1,784 bar - Nominal screw speed: 81 rpm - Maximum screw speed: 100 rpm 5. Hydraulic and electrical system - Main motor power: 160 kW - Installed heater power: 93 kW - Number of heating zones: 7 - Number of dry cycles according to EUROMAP 6: 648 cycles/h - Hydraulic oil tank capacity: 2,400 l 6. Machine dimensions and weight - Length: 14,170 mm - Width: 4,040 mm - Height: 2,930 mm - Net weight including control cabinet: 92,000 kg (92 tons)

Condition: repair required (used), Year of construction: 1999, operating hours: 33,400 h, functionality: limited functionality, machine/vehicle number: 70185/300/99, screw diameter: 45 mm, injection pressure: 2,038 bar, total length: 7,200 mm, total width: 2,000 mm, total height: 2,500 mm, overall weight: 22,000 kg, For sale is an ENGEL ES650/330/300 TL injection molding machine in a C-frame design. Tjdszrngyopfx Aired The machine is ideal for repair, modernization, or as a source of spare parts. Technical data Manufacturer: ENGEL Type: ES650/330/300 TL Year of manufacture: 1999 Machine number: 70185-300-99 Clamping force: 3,000 kN Design: C-frame 1 horizontal injection unit Screw diameter: 45 mm Injection volume: 292 ccm Injection pressure: 2,038 bar Max. injection temperature: 450 °C Min. tool mounting height: 400 mm Max. distance between mold mounting plates: 1,300 mm Ejector stroke: 200 mm 3 hydraulic core pulls Dimensions and weight Length: 7.20 m Width: 2.00 m Height: 2.50 m Total weight: approx. 22,000 kg Connection values Pump drive power: 37 kW + 11 kW Heating power: 15.3 kW + 9.2 kW Fuse rating: 250 A Condition The machine is basically functional but requires repair or maintenance. Further information on the condition can be provided upon request. Sale Inspection possible by appointment Sale from our location Please contact us for further information, images or to arrange an inspection.

Condition: ready for operation (used), Year of construction: 2014, operating hours: 60,000 h, functionality: fully functional, machine/vehicle number: 7230-0232, clamping force: 500 kN, screw diameter: 25 mm, • Sumitomo SHI Demag IntElect 50/370-110 • Year of manufacture: 2014 • Machine no.: 7230-0232 • Clamping force: 500 kN / 50 t • Tie bar spacing: 370 mm Tode Aggumjpfx Airsd • Injection unit: 110 • Screw diameter: 25 mm • Control system: NC5 / CDIAS • including removal device Geiger MiniServo 1.5 • Approximately 12 million cycles In addition, we are selling a Sumitomo SHI Demag IntElect 50/370-110, year of manufacture 2013. Both machines have extensive features, including electric ejectors and screw drives, active tool protection functions, process data recording, and interfaces for handling and peripheral devices. The machines were in operation until they were dismantled. If you are interested, we would be happy to provide you with further information and images. Our asking price for the complete package, including both machines and both Geiger removal devices, is €55,000 net, ex works.

Condition: used, Year of construction: 2003, operating hours: 6,659 h, functionality: fully functional, KraussMaffei injection molding machine KM 300-1400 C2, manufactured in 2003, with extensive peripherals and material supply system. Manufacturer: KraussMaffei Machine type: KM 300-1400 C2 Designation on control panel: KM 300-1400 C2P International size designation: KM 1400 C2/300 Machine type: Injection molding machine Year of manufacture: 2003 Machine no.: 61004124 Machine weight: 14,370 kg Operating hours according to display: 66,598:20 h Control system: KraussMaffei Material supply / dosing: Colortronic UB95 Temperature control / cooling unit: Frigel Microgel RCM80/6HP Year of manufacture Frigel: 2013 Voltage Frigel: 400 V Auxiliary voltage Frigel: 110 V Frequency Frigel: 50 Hz Maximum current Frigel: 17 A Tedpfx Aij Afaqberjd Refrigerant: R407C Refrigerant filling quantity: 2.4 kg Temperature range Frigel: -5 to +90 °C Weight Frigel: 200 kg Additional peripherals: Second Frigel Microgel unit, material conveying system, discharge conveyor belt and rotary table available Available from APRIL 2027

Condition: excellent (used), Year of construction: 2012, Arburg 520S 1600-400/170 e² / Production line with Geiger robot Year of manufacture: 2012 Injection unit: Screw diameter: 35 mm Shot weight: 141 g Injection pressure: 2500 bar Dosage volume: 154 ccm Clamping unit: Clamping force: 160 t Tie bar spacing: 520 x 520 mm Platen size: 695 x 695 mm Ejector: hydraulic Clamping unit: hydraulic Control system: SELOGICA - touchscreen Additional equipment: 2K injection molding machine with rotary table and Geiger robot Very good technical condition Hybrid machine: energy-saving and very quiet Euromap 67 Robot interface Air valve x 4 Hydraulic core pull x 5 Control system with 12 hot runner zones Reinforced injection units – bimetallic Machine with two cylinders / batteries with compressed nitrogen (additional charge for fast operation) The machine features a built-in servomotor in the injection unit responsible for dosing the plastic Todpfxoz Ip Tde Aired Parallel movements Screw diameter in the vertical injection unit: ⌀30 mm - 77 g/PS Integrated Arburg brand conveyor belt and sorting flap Original Weber brand rotary table, highly precise – electrically driven (integrated inverter in the machine) Rotary table and robot available as an additional purchase Dimensions: Weight: 8140 kg Length/Width/Height: 4.81 x 1.84 x 3.45 m All offered machines are started up by our service technicians prior to sale. A video of the technical tests for the selected machine can be provided, or you can participate in live technical tests at our facilities in Łódź. Price: On request

Condition: used, Year of construction: 2000, Plastic injection molding machine, Krauss Maffei, KM 300-1900 C2, dimensions: 6.21 x 2.04 x 2.38 m, weight: 12,500 kg, year of manufacture: 2000. Todpfs Agtbwsx Airjd

Condition: excellent (used), Year of construction: 2011, KRAUSSMAFFEI KM 850-12000 MX injection molding machine Year of manufacture: 2011 Clamping force: 8,500 kN (850 tons) Control system: MC5 Robot: KraussMaffei LRX 500 TECHNICAL SPECIFICATIONS 1. Clamping unit - Clamping system: hydraulic-mechanical, two-platen - Design: 4 pressure pads and 4 locking units on the moving platen - Clamping force: 8,500 kN (850 tons) - Opening force: 560 kN - Column spacing (H × V): 1,140 × 1,140 mm - Dimensions of mounting platens: 1,600 × 1,600 mm - Opening stroke: 1,600 mm - Minimum mold height: 500 mm - Maximum mold height: 1,100 mm - Maximum die opening: 2,100 mm - Ejector stroke: 300 mm - Ejector force: 200 / 100 kN Tedpfe Af H Imsx Airod 2. Plastification unit - Complete plastification unit for thermoplastics - Screw diameter: 135 mm - Backflow valve: yes - Nozzle type: open - Nozzle radius: 25 mm - Nozzle orifice diameter: 9 mm 3. Injection unit - Injection unit type: 12000 - Injection unit adjustment: PV - Screw diameter: 135 mm - Injection volume: 8,588 cm³ - Injection shot weight (PS): 6,098 g - Maximum injection pressure: 1,389 bar - Injection rate: 1,414 cm³/s 4. Hydraulic and drive system - Rated motor power: 132 kW - Hydraulic oil tank capacity: 2,440 l - Cycle time according to EUROMAP 6: 965 cycles/h 5. Control system - Control system: KraussMaffei MC5 - Color operator monitor - Integrated control panel - USB port for data carrier operation 6. KraussMaffei LRX 500 linear robot - Manufacturer: KraussMaffei - Model: LRX 500 - Type: linear robot - Z-axis: 4,000 mm - X-axis: 1,500 mm - Y-axis: 1,250 / 1,250 mm 7. Machine dimensions and weight - Length: 11,720 mm - Width: 2,920 mm - Height: 2,710 mm - Net weight including control cabinet: approximately 49,000 kg (49 tons) Additional equipment - KraussMaffei LRX 500 linear robot - Two-platen hydraulic-mechanical clamping system - MC5 control system - PV adjustment of the injection unit - Plastification unit for thermoplastics with a 135 mm screw

Condition: used, Year of construction: 2020, operating hours: 17,000 h, functionality: fully functional, clamping force: 2,450 kN, screw diameter: 50 mm, clearance between the columns: 610 mm, total length: 6,700 mm, total width: 1,700 mm, total height: 2,000 mm, overall weight: 12,000 kg, power: 48 kW (65.26 HP), input frequency: 50 Hz, input voltage: 400 V, input current: 68 A, We offer this used WOOJIN PLAIMM TE250 injection molding machine, manufactured in 2020. Serial number: 2002501597 Model: TE250 Clamping force: 2450 kN Screw diameter: 50 mm Injection unit: IE780 Tjdpszwupxofx Airjd Electrical power: 48 kW Motor rated current: 50 A Rated current at full load: 68 A Control voltage: 400 V Frequency: 50 Hz Dimensions (L×W×H): 6.7 × 1.7 × 2.0 m Weight: 12 t Date of manufacture: 2020.12.21 If you have any questions or require additional information, please send us a message or contact us by phone.

Condition: used, Year of construction: 2002, functionality: fully functional, Manufacturer: KraussMaffei Type: KM 300-1400 C2 Machine type: Injection molding machine Year of manufacture: 2002 Tsdpfx Aijz Alpgsrsd Machine no.: 254603 Machine weight: 12,500 kg Clamping force: 3,000 kN Control system: KraussMaffei machine control system with screen operation Operating hours according to display: 96,208 h Material supply: Material conveying/dosing components installed on the machine Hydraulics: Rexroth components visible Peripheral control: RMS Systems Touch Control available Conveying technology: Discharge/conveyor belt available Cooling unit 1: Frigel RCM80/6HP Year of manufacture, cooling unit 1: 2012 Voltage, cooling unit 1: 400 V Max. current, cooling unit 1: 17 A Refrigerant, cooling unit 1: R407C Refrigerant charge, cooling unit 1: 2.4 kg Weight, cooling unit 1: 200 kg Cooling unit 2: Frigel RCD80/12HP Year of manufacture, cooling unit 2: 2013 Voltage, cooling unit 2: 400 V Max. current, cooling unit 2: 29 A Refrigerant, cooling unit 2: R407C Refrigerant charge, cooling unit 2: 2.4 kg Weight, cooling unit 2: 240 kg Location: Freiburg Available from APRIL 2027

Condition: good (used), Year of construction: 2003, operating hours: 30,322 h, Demag Ergotech-Viva 500-270 EXTRA Closing force: 50 tons Year of manufacture: 2003 Center distance: 35.5 x 35.5 Installation height: 210 mm Tods Ag Tfpjpfx Aired Screw diameter: 30 mm Displacement: 144 cm3 Operating hours: 30,322

Condition: good (used), Year of construction: 2011, operating hours: 48,060 h, clamping force: 35 kN, screw diameter: 18 mm, clearance between the columns: 32 mm, displacement volume: 23 cm³, injection weight: 21 g, SUMITOMO shi-Demag Systec 35/320-25 Closing force: 35 tons Year of manufacture: 2011 Tie bar diameter: 18 mm Tie bar spacing: 32x32 Mounting height: 320 mm Operating hours: 48,060 Tsdps Agpcqjfx Airsd

Condition: used, Year of construction: 1998, This Demag injection molding machine, type: ergotech pro 50-270, will be auctioned off online in our industrial auction / machinery auction focusing on warehouse clearance of industrial machines – injection molding machines, CNC machining centers, universal lathes, and more. You can find this and many other items on our platform. Tsdpfx Ais Agkd Esrsd

Condition: excellent (used), Year of construction: 2008, DEMAG SYSTEM 800/1120-9500 injection molding machine + DEMAG ERGOTECH DR743 robot Year of manufacture: 2008 | Clamping force: 800 tons | Demag Ergotech DR743 linear robot Hydraulic Demag System 800/1120-9500 injection molding machine from 2008, equipped with an integrated Demag Ergotech DR743 linear robot for automatic part removal. TECHNICAL SPECIFICATIONS 1. BASIC DATA Manufacturer: Demag Model: System 800/1120-9500 Year of manufacture: 2008 Machine type: hydraulic injection molding machine for processing thermoplastic materials Clamping force: 8000 kN (800 tons) Tedpfxo Af Nhfs Aired Injection unit: 9500 Equipment: integrated Demag Ergotech DR743 linear robot 2. CLAMPING UNIT Clamping force: 8000 kN (800 tons) Dimensions of mounting plates: 1620 × 1500 mm Column spacing: 1120 × 1000 mm Minimum mold height: 500 mm Maximum mold height: 1050 mm Maximum distance between plates: 2080 mm Mold opening stroke: 1030 mm Ejector stroke: 350 mm Ejector force: 139 kN Maximum mold weight: 7200 kg 3. INJECTION UNIT Injection unit type: 9500 Screw diameter: 130 mm Injection volume: 7300 cm³ Injection weight (PS): 6640 g Injection pressure: 1300 bar Screw length-to-diameter ratio (L/D): 20:1 4. DEMAG ERGOTECH DR743 LINEAR ROBOT Identification data Manufacturer: Demag Ergotech Model: DR743 Type: DR743-42141000 Year of manufacture: 2008 Serial number: W743-0277 Robot type: linear, designed for automatic part removal Integration with injection molding machine: yes Robot travel ranges X-axis: 1200 mm Y-axis: 2600 mm Z-axis: 3000 mm Electrical and mechanical parameters Supply voltage: 400 V Rated current: 18 A Connected power: 12.5 kVA Robot weight: 750 kg 5. HYDRAULIC AND ELECTRICAL SYSTEM Pump motor power: 110 kW Heater power: 79 kW Hydraulic oil tank capacity: 1300 l 6. MACHINE DIMENSIONS AND WEIGHT Length: 12,300 mm Width: 2700 mm Height: 2700 mm Main unit weight: 33,500 kg Accessory weight: 9700 kg Total weight of main unit and accessories: 43,200 kg

Condition: used, Year of construction: 1999, This Demag injection molding machine, type: ergotech pro 50-270, will be auctioned off online in our industrial auction / machinery auction focusing on warehouse clearance of industrial machines – injection molding machines, CNC machining centers, universal lathes, and more. Tsdpfx Ao Agk Drjirsd You can find this and many other items on our platform.