Used Driving for sale (21,629)

Condition: used, Circular shears with motor drive FASTI Type 502 - 10 - 2 Machine no. No. 9252 009 Year of construction 1992 Material thickness max. 2 mm (400N/mm²) Maximum circular blank diameter 1000 mm Minimum blank diameter 100 mm Cutting shaft speed 60 and 120 rpm Cutting speed 12 and 24 m/min. Blade holder Ø 20 mm Knife diameter Ø 65 mm Projection of the clamping plate 720 mm Projection of the cutting wheel 280 mm Gsdsu Rimmepfx Aatjkb Motor power 1.1 / 1.4 kW Mains connection 380 Volt, 50 Hz - 2 motor speeds - Mechanical clamping tip - Scale on the clamping bracket - electric foot switch - 1 set of cutting blades - Operating instructions with electrical diagram in PDF format Space requirement L x W x H 1600 x 660 x 1350 mm weight 320 kg good condition

Condition: used, mileage: 31,500 km, power: 100 kW (135.96 HP), first registration: 11/1987, fuel type: diesel, next inspection (TÜV): 06/2026, color: red, gearing type: mechanical, number of seats: 9, total length: 7,000 mm, Year of construction: 1987, Equipment: ABS, parking heater, Mercedes-Benz 7.5-ton service vehicle – in very good condition – only 31,725 km. For sale is a Mercedes-Benz service vehicle under 7.5 tons, first registered in November 1987, with an exceptionally low mileage of only 31,725 km. The vehicle comes from official use and is in very good technical condition. Only minor cosmetic signs of wear are present. The truck is ideally suited for trades, fire department conversions, event/promotional vehicles, food truck conversions, camper van projects, or export. Vehicle data Make/Model: Mercedes-Benz Type: Truck < 7.5 tons – service vehicle First registration: November 13, 1987 Mileage: 31,725 km Engine: 5,917 cm³ diesel Power: 134 hp Drive: Rear-wheel drive Transmission: Manual 5-speed Condition: Only cosmetic damage, technically very good Availability: Immediately Chassis & Axles * 2 axles, 1 driven * Permissible front axle load: 3,500 kg Godezbfgdepfx Aatskb * Permissible rear axle load: 4,800 kg * Permissible total weight: 7,490 kg * Technical total weight: 7,490 kg Tires – 1st axle: * Tire size: 9.5 R17.5 * Condition driver & passenger side: >70% Dimensions * Overall length: 7,000 mm * Overall width: 2,500 mm * Overall height: 2,900 mm Special features * Extremely low mileage * Robust Mercedes diesel engine from the older series (very durable) * Ideal as a base vehicle for conversions * Immediately ready for use * No known technical defects * German registration documents Conclusion: A rare, excellently preserved Mercedes-Benz 7.5-ton truck with extremely low mileage – perfect for commercial use, conversion projects, or export. Vehicles in this condition and with this history are hardly ever found anymore. * WhatsApp message for interested parties: Just let me know – KARL SCHUSTER

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, center width: 1,200 mm, overall weight: 7,000 kg, travel distance X-axis: 500 mm, travel distance Z-axis: 800 mm, controller model: Bosch Rexroth MTX, TECHNICAL DETAILS Center distance: 1,200 mm Max. outer diameter: 350 mm Max. workpiece weight between centers: 50 kg Cross slide, X-axis Travel, X-axis: 500 mm Max. speed: 30 m/min Resolution: 0.1 µm Longitudinal slide, Z-axis Travel, Z-axis: 800 mm Max. speed: 30 m/min Resolution: 0.0005–0.1 mm Multi-function head, B-axis Swivel range: -45° to +225° Swivel time for 180°: < 3 s Positional accuracy: 0.0002° Repeatability: 1″ Resolution: 0.001° External machining Max. machining length: 750 mm Peripheral speed: 50 corundum / 80 CBN Drive power: 15 kW Max. grinding wheel dimensions: Ø 400 × 50 × 152.4 mm Internal machining Max. bore diameter: 250 mm Max. bore depth: 235 mm Drive power S1: 1.8–7.5 kW Speed range: 30,000–50,000 rpm Workpiece spindle, C-axis Max. speed: 1,500 rpm Drive power: 1.8 kW Drive torque: 90 Nm Resolution of measuring system: 0.001° Roundness accuracy: 0.8 µm Positional accuracy: 0.0001° Tailstock Quill stroke: 50 mm / 80 mm Quill diameter: 60 mm Bearing: hydrostatic Fine adjustment for cylindricity corrections: ± 40 µm 3-point steady rest Clamping range, diameter: 20 – 150 mm Coarse adjustment: 40 µm Fine adjustment: 2 µm Adjustability: stepless MACHINE DETAILS CNC control: Bosch Rexroth MTX Dimensions & Weight Godpfozwm Akex Aatjkb Dimensions (L x W x H): 2,850 x 2,470 x 2,290 mm Weight: 7,000 kg EQUIPMENT 3-point steady rest

Condition: ready for operation (used), Year of construction: 2014, machine/vehicle number: 183610114, functionality: fully functional, stroke length: 1,200 mm, empty load weight: 1,500 kg, working width: 3,000 mm, working height: 1,710 mm, No minimum price – guaranteed sale to the highest bidder! Gksdpfozzbb Njx Aatjb TECHNICAL DETAILS Press drive: Hydraulic Max. clamping width: 3,000 mm Max. clamping height: 1,710 mm Max. clamping depth: 100 mm Number of cylinders: 4 pcs Cylinder stroke: 1,200 mm Horizontal and vertical cylinders: Separately controlled MACHINE DETAILS Voltage: 400 V Current consumption: 3.5 A Fuse rating: 16 A Main motor power: 1.5 kW Connected power: 1.5 kW Dimensions & Weight Dimensions (L x W x H): 3,400 x 1,200 x 2,880 mm Unladen weight: 1,500 kg Number of transport packages: 1 pc EQUIPMENT Remote control

Condition: excellent (used), Year of construction: 2000, operating hours: 25,943 h, functionality: fully functional, machine/vehicle number: 175, total width: 1,350 mm, total length: 1,400 mm, total height: 2,250 mm, grinding spindle motor power: 1,100 W, input voltage: 380 V, overall weight: 1,450 kg, grinding spindle speed: 2,625 rpm, The machine is in perfect working order and underwent a major overhaul in 2020, during which the following parts were replaced or added: - All axes were replaced (including guides, lead screws, all bearings, and supports). - All gears and belts were replaced. - An automatic lubrication system was installed for all axes. - The internal lighting system was modified to highlight all sharp details. Gkodszxup Ujpfx Aatjb - LCD monitors were replaced. - The machine was fitted with an oil mist extractor. - Included is a replacement hard drive containing all the software.

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 60944, Year of construction: 2007, operating hours: 3,334 h, load capacity: 6,000 kg, lifting height: 5,100 mm, free lift: 2,634 mm, fuel type: electric, fork length: 1,390 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Lifting height: 5,100 mm Free lift: 2,640 mm Lifting capacity: 6,000 kg Fork length: 1,390 mm Fork width min.: 450 mm Fork width max.: 1,110 mm Travel direction: 2 travel directions MACHINE DETAILS Mast type: Duplex Drive type: Electric Battery voltage: 80 V Operating hours: 3,334 h Dimensions & Weight Dimensions (L x W x H): 3,230 x 1,890 x 3,800 mm Unladen weight: 7,740 kg EQUIPMENT Fork adjustment Work light Joystick Camera Gjdpfx Aozza Tdoatekb Half cabin User manual available CE marking

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 516327000881, Year of construction: 2007, operating hours: 15,936 h, load capacity: 4,000 kg, lifting height: 4,910 mm, fuel type: electric, mast type: duplex, fork length: 1,200 mm, TECHNICAL DETAILS Lifting capacity: 4,000 kg Lifting height: 4,910 mm Free lift: 0 mm Fork length: 1,200 mm Minimum fork width: 440 mm Maximum fork width: 1,150 mm Number of wheels: 4 MACHINE DETAILS Mast type: Duplex Operating hours: 15,936 h Drive: Electric Battery voltage: 80 V Battery capacity: 930 Ah Dimensions & Weight Dimensions (L x W x H): 2,900 x 1,250 x 3,180 mm Shipping weight: 6,777 kg Gjdpfxezza Ste Aatokb EQUIPMENT Fork adjustment Side shift Full cabin Radio Joystick Heater Work lights Documentation CE marking

Condition: used, functionality: fully functional, Year of construction: 2023, operating hours: 13,979 h, machine/vehicle number: A3231E0532, controller manufacturer: Siemens, controller model: Sinumerik 840D SL, laser type: fiber laser, laser source manufacturer: TRUMPF, laser source model: TruDisk 24001, laser hours: 4,541 h, laser power: 24,000 W, laser wavelength: 1,030 nm, sheet thickness steel (max.): 60 mm, sheet thickness stainless steel (max.): 60 mm, sheet thickness aluminum (max.): 40 mm, sheet thickness brass (max.): 12 mm, sheet thickness copper (max.): 16 mm, table length: 3,000 mm, table width: 1,500 mm, working length: 3,000 mm, working width: 1,500 mm, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, workpiece weight (max.): 1,800 kg, input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, type of cooling: water, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, nozzle changer, safety light barrier, TRUMPF TruLaser 5030 fiber (L76), 24 kW (2023) High-spec 2D fiber laser cutting machine, one owner from new. 3000 x 1500 mm working area. Siemens Sinumerik 840D SL control with 21.5" multi-touch display. In daily production and under TRUMPF maintenance contract from new. Key data Machine No.: A3231E0532 Year of manufacture: 09/2023 Laser source: TruDisk 24001 (external, separate energy supply) Laser power: 24,000 W Working area: 3000 x 1500 mm Max. sheet thickness (thick-sheet package fitted): mild steel 60 mm / stainless 60 mm / aluminium 40 mm / copper 16 mm / brass 12.7 mm Max. simultaneous speed: 280 m/min Machine weight: 7,650 kg Supply: 400 V 3~ / 50 Hz, 22.0 kVA, 3 x 63 A Hours: 13,979 h operating / 4,541 h laser-on Machine Box frame. Gantry drive with linear direct drives. Longitudinal conveyor belt. Transverse conveyor belt with tipping container (right). Process cooler for machine and laser (water/air). Work area illumination. Pilot laser. Spraying equipment. Automatic nozzle cleaning. Closed beam guidance via laser light cable (LLK). Machine status light. Integrated electrical cabinets. Mild steel slats, 67 mm spacing. Slag cart under pallet changer. Cleaning brush. Cutting unit Single cutting-head strategy. Protective glass with online condition checking. Dynamic Focus Control. Automatic nozzle centring. Universal cutting unit with fully adaptive lens system. Control and software SINUMERIK 840D SL. Integrated technology data. Production plan. Multi-sheet processing. Condition Guide. Cutting Guide. Quick post-production. Auto-shutdown. Programmable cutting gas / pressure selection. Microweld. Nanojoints. Oseon Go. Online Update Manager. Remote support interface. Functions and cutting packages AdjustLine, BrightLine fiber, ControlLine, DetectLine, Drop&Cut, FastLine, FlyLine, FocusLine, NitroLine, PierceLine, PlasmaLine, Smart nozzle automation. Integrated camera for process viewing. Fusion cut performance package, Highspeed cutting package, Highspeed Eco cutting package, cutting package for thick sheets, copper cutting package, brass cutting package, gas mix cutting package (N2/O2). Gjdpfszz Sd Ujx Aatskb Gas Witt gas mixer unit with hardware gas mixer for two gases, plus additional cutting gas connection. Pallet changer / automation Automatic heavy-duty pallet changer in longitudinal direction. LiftMaster Compact interface prepared; loading automation not fitted. Safety and extraction CE marking, EC Machinery Directive. Light barriers. Enclosed protective housing with certified door viewing panels left and right. Electrical rolling roof. Multi-chamber compact dust extractor. Data transfer USB interface. RJ45 network interface. Central Link. Remote support. Installation Currently installed on a mezzanine. Mezzanine steel structure not included in the sale. Condition and availability One owner from new, used in daily sheet metal subcontract production in Braintree, Essex. Under TRUMPF maintenance contract from new (two services per year) and still covered - full service history available. Can be viewed cutting under load on any working day by appointment; cut tests welcome. Offered ex works, decommissioned by TRUMPF-certified engineers and loaded onto your transport. Export packing available on request. Enquiries Full TRUMPF order confirmation, service history, hours report, cut samples and video of the machine running available on request.

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, pressing force: 48 t, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 450 kg, Equipment: documentation/manual, HSM VK 4812 P Year of production: 2017 Fully automatic baler. The device has service and maintenance work by an authorized HSM service with a branch in Germany. Gkjdsz Aaf Aopfx Aatjb Press after significant service work - details after direct contact. The baler comes complete with a ramp for ejection of finished bales and stands for binding wires. Pressing force: 480 kN Drive power: 18 kW Voltage / frequency: 400 V / 50 Hz Capacity at 50 kg/m³: 10.2 t/h Bale width x height x length: 1100 x 750 x 600 - 1200 mm Total length x width x height: 6661 x 3994 x 2583 Machine weight: 10.2 t Compressed material: foil, mixed paper, cardboard, die-cutter waste Bale tying: 4-fold with wire We also have other presses in stock. Transport costs depend on weight, volume and, above all, distance, the following information is important for inquiries: Delivery address (postal code and city name), but further details require telephone contact, so please inquire about transport costs and other delivery methods to contact us contact us by phone. Our contact details can be found in the seller's legal information. We sell and export worldwide, and thanks to our very large storage capacity we can also deliver larger quantities flexibly and quickly. We issue intra-Community invoices - without VAT. opening hours Mon-Fri: 8:00-16:00 Sat: closed

Condition: excellent (used), functionality: fully functional, Year of construction: 2018, Load capacity: 150 kg Band width: max. 150 mm Coil diameter: max. 800 mm Spreading range: 230 ... 545 mm Design: • Motorized drive • Loop control via contact switch on the reel base Gksdpozi Exuefx Aatob • Limit stop disc at the rear • Limit stop ring at the front • Selector switch for left/right rotation • Selector switch for manual/automatic operation

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2004, roller (bottom) diameter: 140 mm, roller (top) diameter: 140 mm, working width: 1,500 mm, sheet thickness (max.): 5 mm, overall weight: 1,200 kg, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Number of rollers: 3 Number of driven rollers: 2 Max. sheet thickness: 5 mm Max. working width: 1,500 mm Diameter of top roller: 140 mm Gkodszza U Ujpfx Aatjb Diameter of bottom rollers: 140 mm MACHINE DETAILS Drive: Hydraulic Control: Conventional Power: 3 kW Dimensions & Weight Dimensions (L x W x H): 2,900 x 900 x 1,400 mm Unladen weight: 1,200 kg Transport packages: 1 EQUIPMENT CE marking

Condition: used, Year of construction: 2020, functionality: fully functional, machine/vehicle number: JB00001227, 92x GE Renewable Energy Yaw Drives – Bonfiglioli & NGC – P/N 448W3942P001 We are offering Bonfiglioli Trasmital yaw drive planetary gearboxes manufactured for GE Renewable Energy wind turbine applications. A total of 48 identical units are available in stock. The listed price of USD 2,000 is the price per unit. Buyers may purchase one unit or any required quantity. There is no obligation to purchase the complete stock. These gearboxes are used in the yaw system of a wind turbine to rotate and position the nacelle according to the direction of the wind. The high reduction ratio converts the electric motor input into low-speed, high-torque rotational movement required for controlled nacelle positioning. Some units may have been partially disassembled for easier and safer transportation. For example, the electric yaw motor may have been separated from the mechanical gearbox. All corresponding components are complete, and the separated parts can be reassembled. Technical specifications: 92 GE Renewable Energy yaw drives available for sale in Turkey. •⁠ ⁠64 Bonfiglioli yaw drives •⁠ ⁠28 NGC yaw drives •⁠ ⁠GE P/N: 448W3942P001 •⁠ ⁠Bonfiglioli VMN: JB00001227 •⁠ ⁠36 units complete with electric motors Gkjdpsznu Rqjfx Aatob •⁠ ⁠56 mechanical yaw drives without motors •⁠ ⁠NGC units equipped with 5.5 kW electric motors •⁠ ⁠Units were supplied/used in sets of 4 per turbine •⁠ ⁠From a GE wind turbine fleet in the 1.7–3.2 MW range •⁠ ⁠Production year: 2020 •⁠ ⁠Location: İzmir, Turkey •⁠ ⁠Total quantity available: 92 units Available individually or as a complete lot. Photos, videos and additional technical information available upon request. The products may show signs of long-term storage and transportation, including paint wear, dirt, minor surface oxidation and corrosion on exposed machined metal surfaces. The units are offered in their current condition as shown in the photographs. The components are complete. However, the electrical and mechanical testing status should be confirmed before purchase. Completeness of the components should not be interpreted as confirmation that every unit has been functionally tested. Individual serial numbers, additional photographs, dimensions, weight information and detailed scope of delivery can be provided upon request. The units are available for individual or multiple-unit purchases. Customers may order any quantity according to their requirements. Price: USD 2,000 per unit Available stock: 48 units Minimum order quantity: 1 unit Delivery terms: FCA seller’s warehouse, Türkiye, Incoterms® 2020

Condition: excellent (used), Year of construction: 2016, operating hours: 16,000 h, functionality: fully functional, nominal power (apparent): 11 kVA, controller manufacturer: haas, spindle speed (min.): 10 rpm, spindle speed (max.): 10,000 rpm, spindle motor power: 11 W, number of spindles: 1, number of slots in tool magazine: 21, Equipment: chip conveyor, Here is the complete reference sheet combining the Haas DT-1 machine specifications, probing package, and 5-axis setup in metric units. 2016. Located in Israel Transport cost to Erope 8000 Euro under power Machine Travels & Work Envelope X-Axis Travel: 508 mm Y-Axis Travel: 406 mm Z-Axis Travel: 394 mm Spindle Nose to Table Top: 152 mm – 546 mm Worktable Table Size (L x W): 660 mm x 381 mm Max Weight on Table: 113.4 kg T-Slot Width: 15.9 mm – 16.0 mm T-Slot Center Distance: 125 mm (3 standard slots) Spindle Specs Spindle Taper: BT30 Gjdpjzwxz Ejfx Aatokb Max Speed: 10,000 RPM ATC 20+1 5-Axis Setup (TRT100 Dual-Axis Rotary Table) Rotary Unit: TRT100 dual-axis tilting trunnion (mounted on the table). Platter Diameter: 100 mm Max Part Swing: 213 mm Weight Capacity on Platter: 6.8 kg (3+2 positioning) / 2.3 kg (simultaneous 5-axis) Travel: A-axis (Tilt) ±120°, C-axis (Rotation) 360° continuous Indexing Speeds: 1,000 deg/sec on both axes Control Requirements: 4th & 5th-axis drive options installed on the machine control. Key Software Features: Supports 3+2 indexing and continuous 5-axis simultaneous machining. DWO/TCPC (Dynamic Work Offsets / Tool Center Point Control): Manages work offsets automatically as part angles tilt/rotate, eliminating the need to re-post programs when mounting locations change. Working Clearance: The TRT100 unit consumes ~230 mm of vertical space, leaving a tight Z-axis machining clearance window (~160 mm) inside the machine's 394 mm total Z-travel. Probing & Tool Measurement (WIPS-R / Renishaw) Hardware Package: Workpiece Spindle Probe: Renishaw OMP40-2 (BT30 optical touch probe) Tool Setter Probe: Renishaw OTS (Table-mounted optical tool setter) Receiver: Renishaw OMI-2T (Modulated optical transmission) Tool Setter Functions: Automatic tool length offset setting, rotating tool diameter offset calibration, and in-cycle tool breakage detection. Workpiece Probe Functions: Work Coordinate System (G54–G59) setting, feature inspection (bores/bosses/surfaces), and part alignment skew angle calculation.

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: SN24027024146, Year of construction: 2024, total length: 580 mm, total height: 910 mm, total width: 700 mm, No minimum price – guaranteed sale to the highest bidder! EXW – Dismantling and loading must be arranged by the buyer! The system will be available from November 2026! TECHNICAL DETAILS Installed nozzle diameter: 0.4 mm MACHINE DETAILS Voltage supply: 100–240 V AC Power consumption: Max. 10 A Mains frequency: 50–60 Hz Frequency band: 2,400.0–2,483.5 MHz Max. radio frequency output power: < 100 mW EIRP WLAN standard: IEEE 802.11 b/g/n Gkjdpozx S Eaofx Aateb Operating temperature: 18 °C for PLA up to 38 °C Max. humidity: Max. 85 %, non-condensing Dimensions & Weight Dimensions (W x D x H): 580 x 700 x 910 mm Weight with packaging: Max. 35.0 kg Weight without packaging: Max. 25.3 kg EQUIPMENT Satin powder-coated print bed PEI print bed Spool holder with material guide Power cable USB drive 5 × brass nozzle, 0.4 mm 5 × hardened nozzle, 0.6 mm Operating manual Testing information Note: Print head cable 3 must be replaced.

Condition: used, functionality: fully functional, mileage: 58,109 km, first registration: 06/1971, fuel type: gasoline, axle configuration: 4x2, suspension: parabolic leaf (spring), Year of construction: 1971, Unique food truck Volkswagen T2 pickup with a custom-made round container (in the shape of a cup/can) The container is made of aluminum and is insulated/double-walled and custom-built. Standing height of over 2 meters. 2 side hatches for selling your products. 2 counters/platforms. Passage from the cabin to the sales area. Ready to drive – just start and go. 4 new tires. Gkedszzbbiopfx Aatjb No mandatory vehicle inspection required. Some rust here and there, but there is no other one for sale. VAT-eligible vehicle. Transportation possible if desired. For more information or to arrange a viewing, please let us know.

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, pressing force: 70 t, Equipment: documentation/manual, HSM HL 7009 Re / Li horizontal baler. The machine is in very good condition and regularly serviced by an authorized service center. Gedpfx Aez Aaf Nsatskb This baler is designed for larger waste disposal projects in retail outlets and small and medium-sized central warehouses. Bales from the HL 7009 model have a cross-section of 1100 x 1100 mm and, with a bale length of 1200 mm, can weigh up to 600 kg, ensuring optimal utilization of the truck's payload. Pressing force: 700 kN Specific pressing force: 58 N/cm² Drive power: 10.5 kW Voltage / frequency: 400 V / 50 Hz Idle capacity (theor.): 42.97 m³/h Loading opening width x length: 890 x 1020 mm Bale width x height x length: 1100 x 1100 x 1200 mm Total length x width x height: 5366 x 2525 x 2559 mm Bale weight: 600 kg

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 9.233, Year of construction: 2017, operating hours: 12,400 h, load capacity: 7,000 kg, lifting height: 8,050 mm, free lift: 2,730 mm, fuel type: diesel, mast type: triplex, fork length: 1,190 mm, TECHNICAL DETAILS Lifting height: 8,050 mm Free lift: 2,730 mm Lifting capacity: 7,000 kg Mast height: 3,730 mm Fork length: 1,190 mm Maximum fork width: 1,530 mm Minimum fork width: 590 mm MACHINE DETAILS Mast type: Triplex Fuel type: Diesel Drive direction: 2 Dimensions & Weight Gsdpezxdk Uefx Aatskb Dimensions (L x W x H): 5,250 x 2,100 x 3,730 mm Overall width: 2,100 mm Overall height: 3,730 mm Unladen weight: 12,820 kg Operating hours: 12,400 h EQUIPMENT Fork adjustment Full cab Heater Pneumatic tires Work lights Joystick Free lift Documentation CE marking:

Year of construction: 2010, condition: ready for operation (used), A complete turning line for the production of drive shafts, consisting of a Lang-Laru cut-off and centering machine, three EMAG lathes with robot automation, conveyor peripheral equipment and measuring station, is available. 1) End machining machine Lang-Laru DHZ 03/1250-RR-S, year of manufacture: 2010, tool stations: 2x12, loading: Kuka robot/EWAB conveyor, machine dimensions X/Y/Z: approx. 8600mm/3000mm/4100mm, weight: approx. 15000kg, control: Siemens Sinumerik 840D. 2) 3x vertical shaft turning centers EMAG VTC 250, year of manufacture: 2010, loading: Kuka robot/EWAB conveyor, max. turning length: 630mm, max. swing diameter over bed: 140mm, max. workpiece weight: 20kg, spindle bore: 52mm, speed: 5000rpm, tool stations: 2, tool holder: VDI40, machine dimensions X/Y/Z: approx. 8100mm/3300mm/4300mm, weight: approx. 14000kg, control: Siemens. This is a complete turning line with peripheral equipment and automation. Documentation available. An on-site inspection is possible. Gkodpfx Aaszfp Hhstjb

Condition: ready for operation (used), Year of construction: 2011, machine/vehicle number: 91.898, functionality: fully functional, pressing force: 100 t, stroke length: 120 mm, throat depth: 250 mm, controller model: HACO ATL 565, working width: 3,600 mm, TECHNICAL DETAILS Press force: 100 t Max. working width: 3,600 mm Frame spacing: 3,300 mm Overhang: 250 mm Max. stroke: 120 mm Back gauge depth: 600 mm Crowning system: Mechanical Gedozxdxxspfx Aatskb MACHINE DETAILS Drive system: CNC Control system: HACO ATL 565 Number of axes: 3 (Y1 + Y2 + X) Dimensions & Weight Dimensions (L x W x H): 4,800 x 1,800 x 2,250 mm Weight: 8,200 kg Transport packages: 2 EQUIPMENT Mechanical crowning system Quick-release die holder Tool holder in European style Tools CE marking

Condition: excellent (used), functionality: fully functional, Year of construction: 2006, operating hours: 83,800 h, Equipment: CE marking, LVD STRIPPIT GLOBAL 30 1225 turret press The machine is in very good technical condition and was used by Alsanit. It has been regularly serviced exclusively by the manufacturer's service department. Only new and original spare parts are used during service. The turret press is currently in continuous production use. If you are interested, we encourage you to schedule a visit to confirm the technical condition and technological capabilities of the machine. General data: Location: Alsanit Sp. z o.o., ul. Wieleńska 2, 64-980 Trzcianka, Poland Province: Wielkopolskie Year of manufacture of the turret press: 2006 Date of purchase and installation of the machine: June 2019 Machine operating hours: 83584 cycles Maximum pressing force: 300 kN (30 tons) Maximum sheet thickness: 6.4 mm Turret system type: Thick Turret Control unit: CNC: GE FANUC 180 IP Maximum travel in the X-axis: 2,576 mm Maximum travel in the Y-axis: 1,337 mm Maximum table load (uniform): 145.6 kg Simultaneous speeds: 110 m/min Number of strokes per minute (punch diameter 25 mm): ±2% 400 min-1 Number of strokes per minute (nibbling function - 2 mm): 1000 min-1 Number of strokes per minute (marking/0.5 mm): 1700 min-1 Maximum slide speed in the X-axis: 83 m/min Maximum slide speed in the Y-axis: 73 m/min Number of tool stations in the turret: 30 pcs Station A – max. diameter 12.7 mm: 8 pcs Station B – max. diameter 31.7 mm: 16 pcs Station C – max. diameter 50.8 mm: 2 pcs Station D – max. diameter 88.9 mm: 4 pcs Number of indexed (rotary) stations in the turret: 4 pcs (stations D) Note: Each station D can accommodate a multi-tool (1 multi-tool contains 3 to 8 tools), which increases the number of tools from 12 to 32 pcs. Machine height: 2,325 mm Machine length: 5,584 mm Machine width: 5,160 mm Gksdpfx Aszxzagjatjb Machine weight: 13,750 kg Sheet size: 1250 x 2500 mm Number of sheet clamps (individually programmable): 3 pcs Tilting scrap collector for cut parts: 450 x 500 mm Brush table protecting against scratching the sheets CE certificate Electrical power supply: 380/415 Volt, 35.5 kVA, 63 A, cable cross-section (3+1)x16 mm2 Additional equipment: Scrap conveyor; Brush table MACHINE SPECIFICATION The machine is constructed as a closed bridge frame. The rigid construction ensures stability, reduces noise, vibrations, and oscillations during operation, which in turn has a positive effect on the long service life of both the tools and the machine. The sheet clamps are controlled by a foot switch, and the pin that extends from the table for positioning allows the operator's hands to remain free for proper placement of the sheet on the table. The turret drum of the LVD Strippit Global 30 punch press is made as a cast monoblock, mounted in the machine structure and supported by high-quality and precise bearings. In addition, inside the turret drum, in each tool station, there are hardened and improved sleeves, which can be easily replaced if necessary. The servo drive of the turret ensures precise bidirectional rotation of the turret and the indexing stations (which are locked by a ball head pin after reaching the required angular position, and the accurate linearity and perpendicularity are ensured by tapered, hardened sleeves).

Condition: ready for operation (used), L & Z lathe WEILER MATATOR incl. Heidenhain digital display ND 780 -Center height approx. 150mm -Swinging diameter over carriage approx. 160mm -Swinging diameter over bed approx. 300mm Godpfx Aszpba Ujatekb -Distance between centers approx. 500mm -Three-axis digital display / Heidenhain -Collets / quick-change tool holder & various collets -Chuck guard -Chip guard -Multifix base plate & inserts -Spindle bore 36mm -Speed range 30 - 3500 rpm -Automatic longitudinal / cross feeds -Tailstock MK 3 -Three-jaw chuck -Documentation Dimensions: L x W x H 1.6 x 0.7 x 1.6 meters / Weight 600 kg Errors and omissions excepted.

Year of construction: 2003, condition: ready for operation (used), Cross slide NC1-left, X1-axis: 450mm, cross slide NC1-left, Z1-axis: 1980mm, cross slide NC2-right, X2-axis: 450mm, cross slide NC2-right, Z2-axis: 1980mm, M-head slide-left, Q1-axis: 1980mm, M-head slide-right, Q2-axis: 1980mm, tailstock + steady rest slide-left, W1-axis: 1980mm, tailstock + steady rest slide-right, W2-axis: 1980mm, Y-axis: +/-65mm, workpiece length: 760-3000mm, workpiece clamping diameter: 20-200mm, main drive power: 2x 37kW, main drive speed (stepless): 0-2200/min, tool drive speed (stepless): 0-2320/min, tool holder: VDI50, tailstock center: MK 5, number of tool holders: 12, steady rest: SLU-5 SO, steady rest clamping diameter: 20-200mm, working height: 1300mm, max. workpiece diameter: 20-200mm, max. workpiece weight: 250kg, workpiece drive/clamping: 2x hydraulically operated SAV front-end chucks, max. chuck through-bore diameter: 210mm, spindle power: 2x 37kW, max. rapid traverse speed: 20m/min, control: Siemens 840D SL, connected load: 135kW, length: 7800mm, width: 3000mm, height: 3250mm, weight: 42t, with machine documentation, installation plan, foundation plan, transport plan, Knoll coolant system, Knoll chip conveyor, ILT extraction system and Promot loading and unloading gantry. Regularly serviced by the manufacturer, the machine was completely overhauled by the manufacturer in 2016. An on-site inspection is possible. Gjdpfx Ajztdtleatjkb

Condition: used, Year of construction: 2018, machine/vehicle number: 10619-1, MEYPACK VP 451 tray and wrap-around packaging machine Fully automatic machine for packing beverage cans into trays and wrap-around cartons. Products and formats: - 0.33-litre cans, Ø 66 x 115 mm, loose and in four-packs - 0.5-litre cans, Ø 66 x 168 mm, loose and in four-packs Pack configurations for both can formats: - 4 x 6 loose cans in a wrap-around carton or tray - 3 x 4 loose cans in a wrap-around carton - 2 x 3 four-packs in a tray Output: - Nominal output: 16,000 cans/h - Packaging output: 12 or 24 packs/min, including a 5% capacity reserve Product handling: - Multi-lane bulk product infeed - Four-packs fed transversely on two lanes, with the openings facing sideways - Infeed height: approx. 1,150 mm ± 50 mm - Outfeed height: approx. 650 mm ± 50 mm - Trays and wrap-around cartons leave the machine broad side leading Operating principle: The products are fed continuously in multiple rows, distributed evenly into the lanes of the infeed conveyor using the accumulation principle, and grouped into the required formation. At the same time, a flat tray or wrap-around blank is removed from the magazine and positioned below the grouping station. The servo-driven lowering station receives the product formation and blank and folds the blank tightly around the products. A servo-driven indexing chain then conveys the pre-folded pack through the gluing and compression stations. The finished pack is transferred to the downstream conveyor system via a gravity roller conveyor. Grouped-pack size range: - Length: 200–400 mm - Width: 120–300 mm - Height: 80–200 mm - Tray height: 40–200 mm Packaging material and magazine: - Suitable for almost all commercially available corrugated-board grades; final design subject to approval by MEYPACK - Blank length: 360–1,250 mm - Blank width: 300–700 mm - Magazine capacity: approx. 150 blanks or approx. 400 mm stack height for B-flute board - Flat blanks are separated by vacuum cups and positioned by a belt conveyor - Hot-melt adhesive: commercially available grades approved by the adhesive-unit manufacturer; final design subject to approval by MEYPACK Utilities: - Electrical supply: 3 x 400 V AC, 50 Hz, with neutral and protective conductor; permissible long-term voltage fluctuation ± 5% - Control voltage: 24 V DC - Compressed air: 6 bar, 1/2-inch connection; clean and free from foreign matter, gases and oils Operation and format change: - The machine can be monitored by one operator while performing another task - Operator side can be arranged on the right or left when viewed in the outfeed direction - Fast, repeatable format changes through zero-line design and automatic indexing-chain adjustment - Settings documented in product-specific format lists; clearly assigned and marked change parts Basic machine and components: - Weight: approx. 3,500 kg - Finish: black grey RAL 7021 - Pneumatics: Festo - Hot-melt unit: Nordson Pro Blue - Drives: SEW, protection class IP55 - Control system: Siemens S7 - Operator interface: Siemens Touch Panel TP 1500 - Electrical design in accordance with MEYPACK standard electrical equipment specification E 2017 Included options: - Additional tray takeaway conveyor for manual palletising - Painted-steel roller conveyor with integrated corner transfer, nominal width 350 mm, length approx. 1,100 mm - Two-lane transfer unit with modular belt chain, adjustable side guides on one side and stainless-steel cable duct - Broadband VPN router for remote machine maintenance - Swivel arm for Gkodpfjz Abkyjx Aatob

Condition: like new (used), functionality: fully functional, Ferwood Code: R19000420 - Manufacturer Code: 16.F5.GBG-YA00 - Condition: As new (showroom item) - Functionality: Fully operational - Compatible Machine: - If interested, we offer an overhaul service; please contact us. 8.5KG - 46X39X27 Gkodoyk D Hnspfx Aateb

Year of construction: 2003, condition: good (used), functionality: fully functional, Highly Automated CNC Pipe Bending Cell: Rosenberger RB20 Typical Applications The RB20 series is designed for the cold bending of pipes with one or more bends. Gjdpjzz Hn Ijfx Aatokb It is used in industries such as the automotive industry, furniture manufacturing, and plant engineering, where precise, repetitive bends are required. Technical Features and Function Type: ROSENBERGER RB20 (manufactured in 2003) Performance & Geometry: Servo-electric precision drive with a cold bending capacity of up to Ø 20 x 1.5 mm in steel. High flexibility thanks to freely selectable bending planes within the 78 mm die height and generous 3-axis travel ranges (X/Y/Z: 260 × 146 × 1,170 mm) Control Technology: The logic is managed by a robust Siemens Simatic S7-300 PLC, paired with an industrial operator panel from B&R Robotic Automation: Fully automatic handling (loading/unloading) via an integrated Motoman industrial robot, complete with XRC controller and the corresponding teach-in terminal for path programming. Product removal is carried out reliably via a discharge conveyor belt. Marking system (upgraded in 2021): A modern, high-performance VideoJet 1860 inkjet coder (manufactured in 2021) with microprocessor control enables direct product marking (e.g., lot numbers or barcodes) immediately after the bending process System Safety & Peripherals: CE-compliant safety measures via a SICK safety light curtain and a perimeter safety fence. Optical status indication via R