Used Grain Scale for sale (2,934)

Condition: like new (used), Year of construction: 2020, functionality: fully functional, machine/vehicle number: Zsk 119 mc+, type of input current: three-phase, total length: 11,000 mm, year of last overhaul: 2024, total width: 1,500 mm, total height: 1,500 mm, overall weight: 18,000 kg, Coperion extruder, 1200 hp (930 kW), 380 volts, 50 Hz. Designed for high-moisture extrusion (TVP or HMMA, high-moisture meat analogue), with an output of 1 to 10 tons/hour. Screw diameter: 2 x 118 mm; ABB inverter for the 1200 hp motor; liquid dosing system; solid dosing system; control panel. Also available: Urchel cutting device and rotary IQF freezer. This extruder can also be used for dry or wet pet food. Bledpozti Tkjfx Abtjl This equipment has very few operating hours.

Condition: new, Year of construction: 2022, functionality: fully functional, Extruder for protein, TVP, and high-moisture analogues. 110 kW. This equipment has never been used and is complete. Pre-conditioner Extruder Polycool 500 and one Polycool 1000 6 cooling and heating regulators, Thermoplas. Dosing system, Bühler (loose weight) for protein Stainless steel control panel Venting system for the extruder Dosing system for liquids (Netsch) Bledpozh I Dqsfx Abtol

Condition: like new (used), Year of construction: 2021, operating hours: 10 h, functionality: fully functional, machine/vehicle number: ABT 1/2000-8, type of input current: AC, overall weight: 4,200 kg, input voltage: 400 V, input frequency: 50 Hz, The 2 tons/hour Belt Dryer System (model ABT 1/2000-8) is an industrial drying unit manufactured by ASOS PROSES MAKİNA SAN. VE TİC. A.Ş. (Turkey). It is designed for the continuous drying of granular or particulate materials such as pet food, cereals, grains, feed, agricultural products, and similar bulk goods. The system operates indoors on a single production line, 24 hours per day, under ambient temperatures of 5–35 °C and relative humidity between 60–80 %, at sea level. The machine is engineered to reduce moisture content from 28 % to 12 %, with a feed rate of 2,000 kg/h, evaporating 364 kg of water per hour, and delivering a dry output of 1,636 kg/h. It requires 364,000 kcal/h of thermal energy, typically provided by combustible gas, with a drying temperature range of 50–60 °C. Total electrical consumption is 37 kW, with 46.2 kW installed power, powered at 400 V / 3-phase / 50 Hz, and an estimated nominal current of ≈ 78.5 A. Noise levels are below 85 dB(A) at 1 m. The required installation space is 4 m (width) × 10 m (length) × 4 m (height). The Belt Dryer unit has a drying surface of 16 m², a belt width of 2,000 mm, and a length of 8,000 mm. It uses a single-pass polyester belt. Both upper and lower casings are made of galvanized steel with rock wool insulation on heated surfaces. Inspection hatches and instrument sockets are provided on both sides for easy access and monitoring. The system includes a spreader unit for uniform material distribution, a burner chamber (400,000 kcal/h, carbon steel), and a set of circulation and exhaust fans (galvanized steel, direct drive, VSD). Multiple motors (totaling 46.2 kW) drive feeding, mixing, drying, ventilation, and heat exchange equipment. Control is managed through a floor-standing MCC and PLC cabinet (IP55, 600×4000×2200 mm), equipped with a Siemens S7-1500 PLC, 17" SCADA touchscreen (TP1900), Profinet communication, and ABB/Danfoss VSDs. All signal and power cables and galvanized trays are included, along with galvanized structural supports. Bledpfx Absyb Rpdstjl The system is suitable for industrial-scale drying operations in the food, feed, agricultural, and processing industries, offering stable performance, low noise, and automated control. It is built for durability with galvanized steel construction, easy maintenance access, and optional on-site erection and commissioning by ASOS engineers. Delivery time is typically 10–12 months from advance payment, and the equipment is guaranteed for one year against material and manufacturing defects.

Condition: new, Year of construction: 2023, New machine Year of manufacture: 2023 MACHINESEEKER ENQUIRIES: Please understand that we do not offer this new machine outside our designated sales area in Germany (Rhine-Main region and North Rhine-Westphalia). Such enquiries will not be answered. Equipment and technical specifications: In intermediate lacquer sanding (Cd-L) configuration Robust, space-saving single wide-belt sander for demanding calibration and fine sanding tasks • Constant working height due to upper part adjustment • Working width: 1350 mm • Over-belt sanding with combination unit • Entire sanding unit inclinable up to 10° • Serrated rubber contact roller of proven hardness • Infinitely adjustable contact roller height according to a grain scale • Pneumatic lifting/lowering of the contact roller according to aggregate selection • Sanding pad with quick-release sliding insert • Parallel spring-loaded, ground steel pressure roller at the infeed • Rubberized pressure roller at the outfeed • Belt drive motor: 11 kW (1100 mm), 15 kW (1350 mm), 18.5 kW (1600 mm), 400 V/50 Hz, soft start for low current draw at startup • Electrically controlled, precisely adjustable height positioning with digital readout Blodpfezi Hwfex Abtsl • Belt tensioning, control, and oscillation: pneumatic, compressed air usage approx. 2 l/min • Optimum safety thanks to automatic immediate stop with disc brake in case of belt break, belt drift, pressure drop, or opening of belt access door • Workpiece feed: 1.1 or 1.5 kW with fabric-reinforced rubber conveyor belt • Vacuum device for worktable with small parts section, fan integrated in machine frame • Complete electrical system with contactor control; automatic star-delta start of main motor, motor protection, and ammeter for chip removal monitoring • Pass-through height: 200 mm • Sanding belt dimensions: 1350 x 2000 mm • Automatic thickness adjustment across the full working width • Workpiece overthickness protection with immediate feed stop and automatic lifting of machine upper structure • Stepless regulation of material removal • Electronic feed regulation on the control panel, stepless from 3 – 15 m/min • PLC control/programming with color touchscreen and TEACH-IN memory (one-touch based on sanding result, no input required) • Pneumatic conveyor belt tracking control • Workpiece support tables at infeed and outfeed • ENORMATIC: Fully automated rapid setup and feed activation (very useful for large workpieces) • eco* energy-saving mode • Error diagnostics • Order and operating hour counters - Electronic segmented sanding pad, segment width 22 mm (swiveling special version) - Steplessly adjustable sanding belt speed (with program memory) - Ejector nozzles for sanding belt cleaning, demand-controlled, with additional extraction nozzle - Additional sanding shoe insert for lacquer sanding Including swiveling air knife, complete Availability: short notice Location: Flörsheim

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,000 kg, maximum load weight: 15,000 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,470 mm, total width: 2,550 mm, total height: 1,040 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis with swivel turntable Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 1 pair of removable guide rollers, additional 4 container locks with sturdy 20"-based arms for swap bodies 7.15 and 7.45 Swivel frame with heavy-duty ball bearing swivel ring Wheel chocks with holder Aluminum side impact protection Side impact protection set inward for optimal clearance to the swap body supports Steel underrun protection Underrun protection shortened for optimal clearance to the swap body supports; lighting system mounted in a protected position Rear mud flaps across the entire width (not compatible with forklift mount) Quarter-shell front fenders and half-shell rear fenders *Towing equipment for trailer turntable Towing fork with certified 40 mm tow eye Towing fork mechanically adjustable in length by approx. 6 x 100 mm (approx. 1900–2500 mm); towing fork length set to 2200 mm *Axles + Suspension BPW or SAF drum brake axles, at the manufacturer’s discretion “Laser-aligned axles/chassis” to reduce tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system Color-coded piping for easy maintenance. Air reservoir: 180 liters Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the tractor unit, Bjdpszd Uvljfx Abtsll EBS, Electronic Brake System with EBS connector at the front, with connecting cable, Caution: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! With raise/lower valve, hold function in both lower and raise positions Axle load detection via EBS CAN bus signal, for display in the cab; the truck must be equipped accordingly; no truck installation (no calibrated scale) Tire pressure monitoring system *Wheels and tires 235/75 R17.5, brand selected by the manufacturer Steel rims in twin configuration, factory silver *Electrical System 24 volts, Aspöck Eco LED II multi-chamber lights, yellow LED side lighting linked to the turn signals (“flashing side lights”), LED license plate lighting, (Note: With certain towing vehicles, false diagnostics may occur even though the system is functioning properly) 2 white LED front position lights 2 white/red rear lane-keeping lights (LED) 2 x 7-pin reverse-polarity-protected connectors at the front, with connecting cable, LED work lights on both sides (activated by the reverse light) 2 additional LED work lights at the rear, activated by the reverse light 1 LED work light at the front, centered between the crossbars, shining toward the rear, activated by the reverse light *Country of Registration/License Plates Germany with DEKRA approval and certification (in accordance with §13 EG - FGV) 24/7 service hotline prepared for single-line license plate holders Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Paint Finish Frame hot-dip galvanized or painted according to customer preference

Condition: ready for operation (used), Year of construction: 2004, operating hours: 11,298 h, functionality: fully functional, machine/vehicle number: 665001, travel distance X-axis: 700 mm, travel distance Y-axis: 550 mm, travel distance Z-axis: 450 mm, workpiece weight (max.): 2,000 kg, spindle speed (max.): 42,000 rpm, number of slots in tool magazine: 40, No minimum price – guaranteed sale to the highest bidder! Submitting a bid obligates you to collect the item within the period of September 21st to October 1st! TECHNICAL DETAILS Travel in X-axis: 700 mm Travel in Y-axis: 550 mm Travel in Z-axis: 450 mm Feed Axes Max. travel speed X, Y, and Z axes: 30 m/min Max. acceleration X, Y, and Z axes: 15 m/s² Positional accuracy TP according to DIN ISO 230-2: 0.005 mm Repeatability: 0.002 mm Work Table Table length: 850 mm Table width: 700 mm Number of T-slots: 5 Bljdpfezqupxjx Abtjl T-slot dimensions: 18 H12 Table load: 2,000 kg Max. workpiece weight: 2,000 kg Distance spindle center – table: 550 mm Spindle Spindle mount: HSK-E 40 Spindle speed: 3,000 - 42,000 rpm Spindle power: 17 kW Tool Changer Tool magazine positions: 40 MACHINE DETAILS Machine type: CNC HSC machining center CNC control: Andronic Electrical Connection Data Supply voltage: 400 V Supply frequency: 50 Hz Fuse rating: 32 A (?) Dimensions and Weight Overall length: 3,300 mm Overall width: 2,300 mm Overall height: 2,300 mm Overall weight: 7,700 kg Operating Data Machine operating time: 275 d 5 h 13 min 39 s Spindle operating time: 11,297 h 20 min 11 s EQUIPMENT - Full enclosure - Dust and fluid-proof guides - Oil mist extraction - Compressor cooler - Frequency inverter - Heidenhain glass scales in X, Y, and Z axes - Work light in the interior - Technical documentation - Workbench - HSK-E-40 tool holders - Tools - Workbench dimensions: approx. 1,500 × 900 × 1,100 mm External Reference: Demo - Lot 2

Condition: used, functionality: fully functional, Pall Stax SXLSC02 Lab Scale Chassis. Operating Pressure: 3.5 bar Operating Temp: 60C Good working condition. Please check out our other listings as well. Bledpfst U Shgsx Abtel

Condition: excellent (used), For sale: Retsch BB300 Jaw Crusher (Manganese) Bsdpsxckcrefx Abtoll The machine is fully operational and in EXCELLENT technical and visual condition – only occasionally used. Application: Crushing of medium-hard, hard, and tough materials with hardness up to 10 on the Mohs scale. - Gap width (mm): 1-40 - Feed grain size (mm): < 150 - Final grain size (mm): 5-40 - Sample volume/capacity: up to 600 kg/h - Motor power (kW): 3.0 - Crushing jaws made of manganese steel

Condition: used, Year of construction: 2014, functionality: fully functional, machine/vehicle number: 495 441, Vertical grinders for producing pearl barley, spelt, and emmer wheat, as well as for grinding lentils. Bledpjznuiajfx Abtsl

Condition: used, machine/vehicle number: 13510, Machine: SAUTELMA ROTOLOK MINISMART Scales SAUTELMA Bedpozx Dpqefx Abtsll

Condition: used, MANFACTURER - PRO-ECO TYPE - PRECISION DOUBLE LOOP SLITTING LINE MATERIAL - GRAIN ORIENTED, NON-GRAIN ORIENTED, SILICON STEEL, COLD ROLLED STEEL SHEAR STRESS - 100,000 PSI - SILICON STEEL | 60,000 COLD ROLLED STEEL MAX YIELD STRESS - 80,000 PSI MIN YIELD STRESS - 30,000 PSI MAX COIL WEIGHT - 50,000 LBS ENTRY/EXIT MAX COIL WIDTH - 48" NOMIMAL (50" MAXIMUM) ENTRY/EXIT MIN COIL WIDTH - 8" ENTRY / 1" EXIT MAX COIL OD - 72" ENTRY / EXIT MIN COIL OD - 36" ENTRY / EXIT MAX STRIP THICKNESS - 0.025" IN - SILICON STEEL / 0.050" CRS MIN STRIP THICKNESS - 0.010" MAX CUTS - 32 LINE SPEED - 1200 FPM ELECTRICAL - 575 V, 3 PH, 60 CYCLE AIR SUPPLY - 80 PSI LINE DIRECTION - LEFT TO RIGHT MODE OF OPERATION - FULL LOOP DRIVE-SLIT, DOUBLE LOOP LINE COMPONENTS: COIL CAR MANDREL UNCOILER PEELER TABLE ENTRY PIT GUIDE TABLES INTERMEDIATE GUIDES FELT STAND BEFORE ENTRY SHEAR ENTRY SHEAR SIDE GUIDES SLITTING HEAD BUTECH SCRAP CHOPPERS EXIT TABLE PRESSURE & TENSION ROLL STAND EXIT SHEAR RECOILER WITH OVERARM SEPARATOR EXIT COIL CAR ALSO AVAILABLE: INTEGRATED PACKAGAING LINE, INCLUDING: EXIT TURNSTILE DOWNENDER WEIGHT SCALE UNDER SEMI-AUTOMATED BANDING LINE 5/8" STEEL BANDING PICK AND PLACE STACKER MAX CAPACITY 6000 LBS PER SLIT COIL ROTATING CAROUSEL EXIT CONVEYOR Bedpfx Aezk Nitjbtsll SEMI-AUTOMATIC STRETCH WRAPPING MACHINE WEIGHT STATION CONTROLS, HYDRAULICS AND ELECTRICS FOR LINE

Condition: new, Year of construction: 2026, CORMAK FAN 11 High-Pressure Material Handling Fan – Premium Industrial Blower for Dust and Sawdust Extraction The CORMAK FAN 11 is a premium industrial high-pressure material handling fan designed for demanding dust extraction and pneumatic conveying applications. Delivering an airflow of up to 15,445 m³/h and powered by an 11 kW three-phase motor, it efficiently removes sawdust, wood chips, dust, and other dry particles generated during the processing of wood, metal, plastics, and composite materials. Its robust construction and high static pressure make it an ideal solution for large-scale industrial dust collection systems. Key Advantages High airflow capacity up to 15,445 m³/h for efficient extraction from multiple machines Powerful 11 kW motor for reliable continuous industrial operation Heavy-duty steel housing resistant to mechanical damage and corrosion Versatile application for sawdust, wood chips, dust, and other dry bulk materials Energy-efficient and low-noise operation optimized for long production cycles Flexible installation options for integration into customized extraction systems Construction and Technology Blsdpfx Abevugfwjtsl The CORMAK FAN 11 utilizes a high-efficiency centrifugal impeller engineered to generate substantial airflow while maintaining high static pressure. The dynamically balanced impeller provides smooth operation with minimal vibration, while the welded heavy-gauge steel housing ensures excellent durability in demanding industrial environments. Designed for continuous-duty operation, the fan offers long service life with minimal maintenance requirements. Performance and Efficiency A precision-balanced impeller, industrial-grade electric motor, and optimized cooling system enable the FAN 11 to maintain outstanding performance during prolonged operation without overheating. Its high airflow and strong suction pressure make it ideal for extracting sawdust, wood chips, and fine dust from large woodworking machines, centralized collection systems, silos, and automated production lines. Applications The CORMAK FAN 11 is ideal for: Woodworking shops and furniture manufacturing plants Metalworking, plastics, and chemical processing industries Agricultural storage facilities and grain drying installations Automated production lines with centralized dust extraction Pneumatic conveying systems for dry industrial materials Standard Equipment Complete centrifugal fan assembly with 11 kW motor Heavy-duty steel housing with inlet and outlet flanges Industrial centrifugal impeller designed for continuous operation Optional Equipment Inlet and outlet diameter reducers Installation and mounting kits Cyclone separators and filtration systems Technical Specifications Parameter Value Maximum Airflow 15,445 m³/h Inlet Diameter 350 mm Outlet Diameter 350 mm Static Pressure 3187–2019 Pa Motor Power 11 kW Power Supply 400 V Dimensions (L × W × H) 920 × 1050 × 1060 mm Weight 170 kg

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, machine/vehicle number: 0-256-73-1249, working width: 1,350 mm, grinding belt length: 2,150 mm, workpiece height (max.): 160 mm, grinding belt width: 1,370 mm, volume flow: 3,660 m³/h, TECHNICAL DETAILS Working width: 1,350 mm Workpiece thickness: min. 3 mm / max. 160 mm Sanding belt width: 1,370 mm Sanding belt length: 2,150 mm Unit 1 – Contact cylinder Sanding belt cutting speed: 18 m/s Rubber cylinder: 65° Cylinder diameter: 240 mm Combination sanding unit Sanding belt speed: 12 m/min Rubber cylinder: 55° Shore Cylinder diameter: 140 mm Width of pneumatic foot: 80 mm MACHINE DETAILS Voltage: 400 V / 50 Hz Drive power Unit 1: 15 kW Drive power Unit 2: 15 kW Total power consumption: 33 kW Dust extraction connection Unit 1: Ø 180 mm Dust extraction connection Unit 2: Ø 180 mm Dust extraction volume: 3,660 m³/h Recommended dust extraction speed: 20 m/s Compressed air requirement: 20 l/min at 6 bar EQUIPMENT Sanding belt change on the left side Automatic clamping of the contact cylinder, e.g., during belt change Automatically adjustable rubber cylinder Grain size compensation on the contact cylinder Combination sanding unit L with pneumatic foot for calibration Automatic anchoring/fastening Bsdpfxezvnfwe Abtoll Grain size compensation on the rubber cylinder Automatically adjustable pneumatic foot

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,480 kg, maximum load weight: 34,520 kg, overall weight: 38,000 kg, axle configuration: 3 axles, total length: 7,450 mm, total width: 2,550 mm, suspension: air, tire size: 385/65 R22,5", Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Semi-Trailer Container Chassis Fine-grained steel welded construction, semi-trailer plate with replaceable 2 kingpins and 2 kingpin positions Front locking mechanism on tipper ram mounting block with guide wedges on both sides, rear locking mechanism on continuous rotary shaft with spring return Without subframe for self-supporting containers Container mounts: Locking cross members, double-mounted for securing 1 x 20-foot container (Note: low fifth-wheel load for 20-foot containers) 24 metric tons, 2-speed support jack, single-sided operation, with straight lower section, without thrust compensation Clear support foot corner dimension or clear rear swing radius approx. 1850 mm 2 wheel chocks with holders Half-shell fenders with anti-spray flaps per EC standards Hydraulics Low-pressure cylinder, max. 170 bar, smallest stage hard-chromed, with HDK Screw coupling, fixed part, nominal diameter 48 mm. (without hose connection) Hydraulic operation via truck auxiliary power unit Hydraulic connection with hose and HDK screw plug, nominal diameter = 48 mm, with knurled nut Axles + Suspension 3 SAF disc brake axles with 430 mm disc diameter Laser-measured axles/chassis to reduce tire wear and fuel consumption Bledpei Ri Euefx Abtjl Offset wheelbase mm (combined transport) up to 44to Gross train weight Air suspension. Brake System 2-line compressed air brake system Color-coded lines for easy servicing. Spring-loaded parking brake 2 non-reversible coupling heads at the front, without connecting line EBS, Electronic Brake System with EBS socket at the front, without connecting cable Caution: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! With lift & lower valve Vehicle stability control system Axle load detection via EBS CAN bus signal, for display in the cab; the truck must be equipped accordingly; no truck installation required (no calibrated scale) Wheels and Tires 6 385/65 R22.5 (manufacturer’s choice) 6 steel rims, factory silver Electrical System 24 volts, multi-chamber lights, yellow LED side lighting 2 white front position lights 2 white/red rear lane-keeping lights 2 x 7-pin reverse-proof sockets in front, without connecting cables Country of Registration/License Plates Germany With DEKRA approval and inspection report (in accordance with §13 EG - FGV) 24/7 Service Hotline Prepared for single-line license plate holder Contour markings with reflective strips per ECE R 048, white on the sides and red at the rear Paint finish Frame: colour of choice 10-year warranty against rust-through Support feet: Black coated Note: Archive images!

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,100 kg, maximum load weight: 34,900 kg, overall weight: 38,000 kg, axle configuration: 3 axles, total length: 7,690 mm, total width: 2,550 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 100 %, Custom-Made Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Chassis, Saddle, Container Fine-grained steel welded construction, saddle plate with 2 replaceable kingpins Container receptacles: 1 x 20 ft in the center (or swap body container 7.15 / 7.45), not retractable at the front, the pivot pins of the container locking mechanism in the longer version 24 tons, two-stage support jacks, single-sided operation With anti-splash flaps according to EC standards Front axle drip tray with 1 1/4 inch drain pipe + 1 1/4 inch shut-off valve, including drip pan, with perforated tread plates, approx. 400 mm wide, left + right between the drip tray and the longitudinal beam 4 hose racks, approx. 4500 mm long (hose box) for hose pipes, 2 x DN 200 on the outside + 2 x DN 160 arranged in the center, at the rear hose box (stainless steel) 300 mm deep, splash-proof, lid (stainless steel) all around with rubber seal, with drain hole at the lowest point, then without lid on the hose pipes 1 stainless steel grounding lug at the rear on the right side of the frame, with international grounding sticker on the frame Climbing steps at the rear right on the underrun protection, at the rear right on the outside of the main beam, tread plate approx. 260 mm long and 300 mm wide Axles + Suspension SAF disc brake axles Axle/suspension laser-measured for reduced tire wear and fuel consumption Offset axle spacing (combined transport) up to 44 tons total train weight Air suspension 1st axle: automatic lift axle, including forced lowering and start-up assistance, activation 3x brake Braking system 2-line compressed air braking system Color-coded line routing for easy maintenance Blodpfx Aboi Rixkotel Spring brake parking brake 2 fail-safe coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! With raising and lowering valve Vehicle - Driving stability system Axle load detection via EBS-CAN bus signal, for display via the display in the driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scale) Wheels and tires 385/65 R22.5, manufacturer's choice Steel rims, factory silver Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 1 x 15-pole socket at the front, without connecting cable Operating instructions The specified total weight is technically possible, but depending on the load, the total weight may not be reached while complying with the permissible axle/support and saddle loads. (Poor driving and handling behavior may occur due to incorrect load distribution) This vehicle may only be loaded with 20' tank containers that comply with ISO 668 and in particular ISO 1496-3! The tank containers must have "end-load-transfer areas"! Country of registration / signs Germany Type approval according to EC 2007/46 24/7 service hotline Prepared for single-row license plate holder Warning sign according to ECE - 70 Acceptance according to ADR, according to 9.1.1.2 of the ADR, EX/II, EX/III / Vehicle registration certificate for the transport of certain dangerous goods (ex.B3) with warning sign on the rear, not valid for substances according to UN 0

Year of construction: 2025, condition: new, functionality: fully functional, machine/vehicle number: Mev600, Filling and dispensing scale for granules, coffee, pasta, nuts, baked goods, herbs, and all free-flowing products. Filling range: 10 g to 2000 g. • Hopper located on top of the machine, with a volume of 40 liters. • The product is conveyed via a vibrating channel. • Vibrating channel made of stainless steel AISI 304. • Vibrating channel speed is adjustable; faster for coarse weight and slower for fine dispensing. • Electronic load cell on the weighing plate with an electronic weight control system. • Minimum/maximum weight: from 10 grams to 2000 grams (depending on product volume). • Voltage: 220 V, single-phase, 50 Hz. • Air connection: 50 liters/cycle. Bljdpfx Abozx Rk Uotjl CONTINUOUS SEALING MACHINE, TYPE MINISEALING (compatible with the filling system). • Horizontal CONTINUOUS THERMO-SEAL MACHINE with an inclined belt, adjustable belt speed, and adjustable temperature for sealing/closing bags. • Equipped with a DATA PRINTER with 2 lines. • Voltage: 220 V, single-phase, 50 Hz. • Spare parts set included. • MACHINE COMPLIES WITH ALL CEE STANDARDS FOR DEVICES AND SWITCHES. Price (optional): EUR 3,500.00.

Year of construction: 2020, condition: good (used), functionality: fully functional, For sale: Farmet FE1000 Clever Max industrial feed / soybean / grain extruder. Manufacturer: Farmet Model: FE1000 Clever Max Year: 2020 Main motor: 110 kW Throughput: approx. 900–2,100 kg/h depending on material and process setup Condition: used, fully functional Location: Slovakia, EU The extruder was used for approx. 2 years. Additional accessories were never used according to seller information. Included: Farmet FE1000 extruder Clever Max control system PLC control with HMI touchscreen Frequency converter for the main drive Stainless steel steam conditioner Cutting head Electrical control cabinet Accessories as shown in the photos Suitable for: soybean extrusion full-fat soybean processing cereal and grain extrusion oilseed meal / press cake processing compound feed production pet food and fish feed applications, depending on recipe and final line configuration The Clever Max control system allows better adjustment of extrusion parameters through PLC/HMI control and frequency regulation of the main drive. This is a strong industrial extruder suitable for medium-capacity feed and oilseed processing plants. Sold as shown in the photos. Inspection possible. Loading possible. Worldwide shipping on request. Price: FCA Slovakia, plus VAT. Zu verkaufen: Farmet FE1000 Clever Max Industrie-Extruder für Futtermittel, Soja, Getreide und Ölsaaten. Hersteller: Farmet Modell: FE1000 Clever Max Baujahr: 2020 Hauptmotor: 110 kW Leistung: ca. 900–2.100 kg/h, abhängig von Material und Prozess Zustand: gebraucht, voll funktionsfähig Standort: Slowakei, EU Der Extruder war ca. 2 Jahre in Betrieb. Weiteres Zubehör wurde laut Verkäuferangabe nicht benutzt. Ausstattung: Farmet FE1000 Extruder Clever Max Steuerung PLC-Steuerung mit HMI Touchscreen Frequenzumrichter für den Hauptantrieb Edelstahl-Dampfkonditionierer Schneidkopf Schaltschrank Zubehör wie auf den Fotos Geeignet für Sojaextrusion, Vollfettsoja, Getreide, Ölsaaten, Presskuchen, Mischfutter sowie Pet-Food- und Fischfutter-Anwendungen je nach Rezeptur und Linienkonfiguration. Bsdpoxfcwmjfx Abtjll Besichtigung möglich. Verladung möglich. Versand auf Anfrage. Preis: FCA Slowakei, zzgl. MwSt.

Condition: good (used), Floor weighing scale K-PZ Weigher indicator Type: KPZ 52E-9-1 Bjdpfjx Hz Dqox Abtsll Maximum weight: 300 kg Minimum weight: 2 kg, e=: 0.1 kg, T=- 300 kg Dimensions: 800 mm x 1100 mm x 100 mm Including ramp

Condition: like new (used), Year of construction: 2017, functionality: fully functional, This microprocessor-controlled, fully automatic filling scale is designed for weighing and filling powders, granulates, or similar materials. Bodpsyux Tdjfx Abtoll The containers to be processed are manually placed underneath the filling station. The product is dispensed via a stainless-steel hopper with a capacity of approx. 20 liters and conveyed forward into the weighing area by means of a vibratory feeder. Once the preset weight is reached, the load tray opens, and the product is dispensed into the container below via a stainless-steel chute. Technical data: - Current weighing range: 1 – 10 g - Resolution: from 0.1 g - LC display with operator guidance - Automatic control of feeder speed - Statistics with counter, mean value, and standard deviation The output is up to 15 weighing cycles per minute.

Condition: new, functionality: fully functional, machine/vehicle number: WFDFLT33802037879, empty load weight: 3,250 kg, maximum load weight: 34,750 kg, overall weight: 38,000 kg, axle configuration: 3 axles, total length: 6,790 mm, total width: 2,550 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, available in multiple units Chassis, semi-trailer, container Fine-grain steel welded construction, kingpin plate with replaceable 2" kingpin Container fittings: 1 x 20 ft, flush at the rear (Note: low drawbar load with 20 ft container) 24 tons, 2-speed landing gear, single-sided operation, with semi-circular base and straight connection plate, with stroke equalization 2 support wedges with holder Rear underrun protection, steel Spray flaps at the rear, covering the entire width Half-shell fenders with anti-spray flaps according to EC Blsdpfxszbtnis Abtel Storage box for fire extinguishers up to 6 kg Fire extinguisher (ABC powder 6 kg) incl. stainless steel drip tray in the center of the rear container crossbeam, approx. 290 mm wide Axles + Suspension BPW disc brake axles, with 430 mm disc diameter "Axles/chassis laser-aligned" - reduces tire wear and fuel consumption Axle spacing offset 1410/1310 mm (combined transport), up to 44 tons total weight Air suspension 1st axle, automatic lift axle, including forced lowering and start assist, activated by "pressing the brake pedal 3 times" (start assist is functional up to an axle load exceedance of 30% and up to a speed of max. 25 km/h) Braking system 2-line pneumatic braking system Color-coded line routing for easy servicing Spring brake parking brake 2 tamper-proof coupling heads at the front, without connecting line 24-volt EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lift and lower valve Vehicle - driving stability system Axle load detection via EBS-CAN bus signal, for display on the dashboard in the cab, truck must be prepared accordingly, no truck installation (no calibrated scale) Wheels and tires 385/55 R22.5", manufacturer at the discretion of the manufacturer Steel rims, factory silver Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front in LED 2 white/red marker lights at the rear 1 x 15-pin socket at the front, without connecting cable Operating instructions The specified total weight is technically possible; depending on the cargo, the total weight may not be reached while complying with the permissible axle/support and drawbar loads. (Poor driving and handling characteristics possible due to incorrect load distribution) Country of registration/plates Germany with Dekra inspection and certificate (according to §13 EG - FGV) 24/7 service hotline prepared for single-row license plate holder Warning sign "A" for waste transport, foldable ADR approval according to FL/AT with ADR warning sign at the rear Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paintwork Frame RAL 2011 traffic orange "10-year warranty against rust-through" Support feet black coated available in multiple units

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT33802035389, empty load weight: 3,160 kg, maximum load weight: 34,840 kg, overall weight: 38,000 kg, axle configuration: 3 axles, first registration: 03/2024, next inspection (TÜV): 03/2027, total length: 7,690 mm, total width: 2,550 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 90 %, color: grey, The images are archive images! The vehicle may still be in use! Fine-grained steel welded construction, fifth wheel coupling with interchangeable 2" kingpin (Chassis prepared for subsequent retrofitting, drip tray, 4 x hose holders, footboards, Fliegl standard) Container fittings: 1 x 20 ft in the center (or swap body container 7.15 / 7.45 / 7.82), not retractable at the front, the pivot pins of the container locking mechanism in the longer version. 24 tons, 2-speed landing gear, single-sided operation, with semi-circular lower part and straight connection plate, with stroke compensation Chocks with holder Side underrun protection Rear underrun protection with deep step for easier access + footboard inside Semi-elliptical fenders with anti-spray flaps according to EC Axles + Suspension Bjdpfx Ajy Tvuwsbtoll BPW or SAF disc brake axles at the manufacturer's choice, with 430 mm disc diameter, "Axle/chassis laser-aligned" to reduce tire wear and fuel consumption Axle spacing offset 1410/1310 mm (combined transport) up to 44 tons gross vehicle weight Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuated by "3x braking" (starting aid is functional up to an axle load exceeding 30% and up to a speed of max. 25 km/h) Braking system 2-line compressed air braking system Color-coded line routing for easy servicing. Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, without connection line 24 Volt EBS, electronic braking system with EBS socket at the front, without connection cable Note: The trailer may only be pulled by towing vehicles which ensure the effectiveness of the ABS! with lifting and lowering valve + auto-reset function Vehicle - Driving Stability System Axle load detection via EBS-CAN bus signal, for display on the dashboard in the driver's cab, the truck must be prepared accordingly, no truck installation (no calibrated scale) Wheels and tires 385/65 R22.5" manufacturer's choice Steel rims, factory silver Electrical system 24 Volt, multi-chamber lights in LED, yellow LED lighting on the side, license plate lighting in LED, (Note! with certain towing vehicles, false diagnoses may occur, although the function is given) 2 white position lights at the front in LED 2 white/red side marker lights at the rear in LED 2 x 7-pin and 1 x 15-pin non-interchangeable sockets at the front, without connection cable additional LED work lights at the rear, switched via reversing light Operating instructions This vehicle may only be loaded with 20' tank containers that comply with ISO 668 and in particular ISO 1496-3! The tank containers must have "end-load-transfer areas"! Country of registration/Signage Germany with Dekra inspection and certificate (according to §13 EG - FGV) 24/7 service hotline prepared for single-row license plate holder Warning sign according to ECE - 70 Contour marking with reflective strips according to ECE R 048, white on the side, yellow at the rear The images are archive images! The vehicle may still be in use!

Condition: new, Year of construction: 2025, For crushing marble, sandstone, and quartzite, various types of crushers can be used depending on the properties of the raw materials and the desired final product specifications. Here are some common types of crushers that may be suitable for processing these materials: 1. Jaw Crusher: - Jaw crushers are commonly used for primary crushing. They are robust machines that handle tough materials, making them suitable for breaking down hard and abrasive stones like marble and quartzite. 2. Impact Crusher: - Impact crushers are versatile and suitable for both primary and secondary crushing. They work by impacting the material with hammers or blow bars, producing a high reduction ratio. Impact crushers can be effective for shaping the final product. 3. Cone Crusher: - Cone crushers are often used for secondary or tertiary crushing. They are suitable for processing harder stones and can produce well-shaped and fine-grained aggregates. 4. Gyratory Crusher: - Gyratory crushers are used for large-scale primary crushing. They have a conical-shaped head and are well-suited for handling abrasive materials. However, they are less commonly used than jaw or cone crushers. Blodpjq Nx Nnefx Abtel 5. Vertical Shaft Impact (VSI) Crusher: - VSI crushers are suitable for shaping and producing artificial sand. They operate by throwing the material against a set of anvils or impellers to break it down into finer particles. 6. Hammer Crusher: - Hammer crushers are used for crushing softer materials like sandstone. They operate by applying force to the material, causing it to break along natural fault lines. 7. Roll Crusher: - Roll crushers are used for reducing the size of friable materials. They consist of two counter-rotating rolls that compress the material between them. 8. Crawler Mobile Crusher: - Mobile crushers offer flexibility and mobility, allowing them to be used directly at the quarry or job site. Crawler mobile crushers can handle various types of stones, including marble, sandstone, and quartzite. 9. Screening Equipment: - After the initial crushing stage, screening equipment such as vibrating screens may be used to separate different sizes of crushed material. 10. Dust Suppression Systems: - Crushing operations can generate dust, and dust suppression systems are used to minimize environmental and health impacts. When selecting a crusher for marble, sandstone, or quartzite, consider factors such as the hardness of the material, the desired final product specifications, and the production capacity required. Additionally, it's important to integrate the crushing process into an overall plant design that may include screening, conveying, and washing equipment depending on the specific needs of the application.

Condition: used, Year of construction: 1995, max. weight 60 kg; Bljdpfx Abozx Avietjl min. weight 0,4 kg.

Condition: excellent (used), Year of construction: 2018, I - beam section - flat steel 120 x 15 (d 750) mm I-beam section - upend 60 x 10 (d 800) mm L-beam 50 x 5 (d 1200) mm round material 35.0 (d 800) mm bar material dia. max. 70 x 2 (d 1200) mm square material 50 x 40 x 3 mm bending speed 4.3 m/min roll diam. toproll 155 mm bore 50,0 mm total power requirement 1.5 kW weight 320 kg range L-W-H 730 x 830 x 1350 mm Exhibition machine from 2023 with only approx. 2x operating hours Condition as NEW Special price on request Bodszyvbnjpfx Abtjll Equipment: - robust electro-motorized ring/profile bending machine - machine base frame, with rear shelf - horizontal and vertical work possible - 1x freely movable foot switch - segmented standard rollers (divided) - 2x motor-driven rollers - manual delivery of the top roller - analog position display of the top rollers (scale) - manually adjustable side/straightening rollers - CE mark / declaration of conformity - operating instructions in German

Condition: used, Year of construction: 1995, functionality: unexamined, machine/vehicle number: 2031306, type of input current: three-phase, overall weight: 9,200 kg, Roller mill from Bühler, previously used in cornflakes production. Pre-installed are a metal detector and a vibratory channel. Control cabinet is included. Weight of the roller mill approx. 9,200 kg. Bjdpfoxgq Rksx Abtjll