Used Horizontal Bandsaw Wood for sale (11,779)

Condition: new, 1000 mm 1000 mm 1200x1000 mm saw band length 11300 x 80 x 1,3 mm table height 790 mm band speed 14 - 60 m/min total power requirement 18 kW weight of the machine ca. 9,0 t dimensions 5,0 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one Gbedet Eacgepfx Abhoi high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.

Condition: new, capacity 90 degrees: round 305 mm capacity 90 degrees: square 260 mm 350 x 200 saw band length 3375 x 27 x 0,9 mm band speed 37 + 74 m/min table height 940 mm total power requirement 1,5/1,8 kW weight of the machine ca. 0,61 t dimensions of the machine ca. 1,5 x 1,75 x 1,9 m Double miter metal band saw with AutoCut function - Miter cuts up to 60° left and 45° right - Ball bearing turntable - Vice can be moved sideways - Massive, large material support - Automatic cooling Gbsdpjfd Abajfx Abhoi Figure is semi-automatic.

Condition: new, cutting diameter 235 mm dimensions of saw-band 2645 x 27 x 0,9 mm cutting width 280 x 190 mm cutting speed 45/90 m/min 120 mm 120 mm 190 mm Impact energy 170 mm connected load frequency 400 Volt total power requirement 1,1 kW Gbjdpjp Scqyofx Abhsi weight of the machine ca. 290 Kg dimensions 1,2 x 0,8 x 1,2 m Double miter band saw -Miter cuts up to 60° left and 45° right -Vice with quick clamping device -Band tension control -Electr. Automatic cooling

Condition: good (used), Year of construction: 1994, power: 30 kW (40.79 HP), Drum chipper with horizontal feed Gbedpfx Abju Ezp Ashoi max. feed width 300 mm max. feed height 85 mm motor 18.5 kW new rotor bearing with conveyor belt

Year of construction: 1992, condition: good (used), machine/vehicle number: 29-0288, Offer 04612 Technical data: - Cutting range at 90° round 260 mm - flat 450 x 240 mm - Cutting range at 45° round 230 mm - flat 240 x 200 mm - Machine is mounted on original turnstile - saw band dimension 3660 x 25 x 0,9 mm - cutting speeds 20 / 35 / 50 / 70 m/min - Hydr. lifting + lowering of the saw frame - cutting pressure infinitely variable 0 - 10 m/min - Total drive power 400 V / 0,8 kW - Coolant device Gbedpfxjgin Ndo Abhei - space requirement approx. W 2100 x H 1200 x D 1000 mm - weight approx. 500 kg

Condition: new, cutting diameter 280 mm capacity 90 degrees: flat 380 x 260 mm capacity 90 degrees: square 260 x 260 mm turning speed range: 40 / 80 m/min dimensions of saw-band 3440 x 27 x 0,9 mm engine output 1,5 / 1,8 kW weight 670 kg Electro-hydraulic, semi-automatic band saw with additional manual and Gedpfx Aefg E Iasbhjbi semi-automatic-dynamic function, for cuts from 45° right to 60° left. Some features: Pivoting control panel on vertical post. 420 mm large rotary table on roller bearings with preloaded thrust bearing and replaceable steel inserts. Double belt speed (40/80 m/min.)

Condition: new, cutting diameter 330 mm capacity 90 degrees: flat 510 x 320 mm capacity 90 degrees: square 320 x 320 mm turning speed range: 40 / 80 m/min dimensions of saw-band 3440 x 27 x 0,9 mm engine output 1,5 / 1,8 kW weight 670 kg Semi-automatic, electro-hydraulic band saw machine for cutting 60° left to 60° right. Versatile machine with a tape of 4640 x 34 x 1.1 mm for the Cutting pipes, profiles and beams up to a maximum cutting range from 510x320 mm to 0°. The control console on a swiveling arm allows for comfortable and safe operation from any position. Electronic inverter for continuous belt speed regulation from 15 to 100 m/min. Gsdpfxefg E Ibo Abhebi Large turntable with a diameter of 280 mm and engraved exact fine scaling, easily adjustable and stored.

Condition: new, cutting diameter 225 mm dimensions of saw-band 2480 x 27 x 0,9 mm table height 935 mm cutting speed 45 + 90 m/min 225 mm 145 mm 90 mm 150 x 245 mm 190 x 150 mm capacity 60 degrees: flat 120 x 90 mm total power requirement 1,1 kW weight of the machine ca. 0,24 t Dimensions (LxWxH) 1380 x 580 x 930 mm - With an output of 1100 watts, the device is ideal for processing hard types of metal. - Thanks to the emergency stop and automatic switch-off, you can work safely - The low-noise electric motor ensures a quiet working atmosphere Gbsdpfx Absfb Nbdohei - Comfortable buttons guarantee pleasant operation of the device.

Condition: new, cutting diameter 220 mm saw band length 2455 mm table height 850 mm cutting width 230 mm cutting speed 25 - 80 m/min dimensions of saw-band 2455 x 27 x 0,9 mm 90 mm 90 mm 90 x 100 mm 150 Impact energy 150 Air consume per blow 150 x 210 220 mm stroke back stop 210 mm cross-slide 230 x 185 total power requirement 1,2 kW weight of the machine ca. 0,24 t dimensions of the machine ca. 1,2 x 0,6 x 1,7 m SPECIAL PRICE!!! -Miter cuts up to 60° left - Cutting speed 25 - 80m/min. - Vice with quick release device -Carbide saw band guide -Tape tension control -Electr. automatic cooling Auto-Cut-System = 3 step system -Automatic saw frame lowering via the hydraulic cylinder -Infinitely adjustable feed Godpfx Asd Iip Tsbhjbi -with limit switch - rapid lowering of the saw frame from the rest position to the workpiece, then switch to normal saw feed -Manual mode

Condition: new, cutting diameter 220 mm saw band length 2455 mm Gsdpfx Aod Iip Usbhsbi table height 850 mm cutting width 230 mm cutting speed 35 + 70 m/min dimensions of saw-band 2455 x 27 x 0,9 mm 90 mm 90 mm 90 x 100 mm 150 Impact energy 150 Air consume per blow 150 x 210 220 mm stroke back stop 210 mm cross-slide 230 x 185 total power requirement 1,2 kW weight of the machine ca. 0,24 t dimensions of the machine ca. 1,2 x 0,6 x 1,7 m SPECIAL PRICE!!! -Miter cuts up to 60° left -Cutting speed 35 / 70 m / min. - Vice with quick release device -Carbide saw band guide -Tape tension control -Electr. automatic cooling Auto-Cut-System = 3 step system -Automatic saw frame lowering via the hydraulic cylinder -Infinitely adjustable feed -with limit switch - rapid lowering of the saw frame from the rest position to the workpiece, then switch to normal saw feed -Manual mode Share of freight costs 85 EUR

Condition: new, cutting diameter 170 mm dimensions of saw-band 2080 x 20 x 0,9 mm table height 880 mm cutting speed 40 + 80 m/min 170 mm 125 mm 150 x 190 mm 95 x 120 mm Gedpog Trvrefx Abhobi total power requirement 1,1 kW weight of the machine ca. 0,24 t Dimensions (LxWxH) 870 x 1.550 x 1.740 mm mm This metal band saw comes with a closed worm gear. It also has hydraulic pressure control and a base frame that can be rotated through 45 degrees. Other features include emergency stop, the complete cooling system, the factory base frame, automatic switch-off and the quick-release device.

Condition: new, cutting diameter 250 mm capacity 90 degrees: flat 280 x 220 mm capacity 90 degrees: square 220 x 220 mm Gbodpsfg E H Rsfx Abhoi turning speed range: 36 / 72 m/min dimensions of saw-band 2950 x 25,4 x 0,9 mm weight of the machine ca. 0,4 t Dimensions (LxWxH) 1,5 x 0,9 x 1,5 Semi-automatic function: Vice closes and motor starts, saw head lowers for the cut, motor switches off, saw head rises, Vise opens. Some features: New centralized switch console on an articulated arm. Latest generation hydraulic control unit, highly powerful and with low energy consumption. Base frame with pull-out coolant container. The machine complies in all areas CE regulations!

Condition: new, cutting diameter 250 mm saw band length 3150 x 27 x 0,9 mm table height 750 mm cutting width 170 x 310 mm cutting speed 25 - 90 m/min 130 mm 130 mm 205 mm Impact energy 205 mm Gedpspam E Rofx Abhobi connected load frequency 400 Volt total power requirement 1,5 kW weight of the machine ca. 0,5 t dimensions 0,95 x 1,16 x 1,98 m Solid band saw - Double miter cuts on the right up to 60°, on the left up to 45° - AutoCut - Vice with quick clamping device - Belt tension control - Electric automatic cooling system - Material stop max 600mm

Condition: new, cutting diameter 225 mm saw band length 2455 mm table height 850 mm cutting width 245 x 150 mm cutting speed 45/90 m/min Gedpfjgxi D Tox Abhebi dimensions of saw-band 2480 x 27 x 0,9 mm 90 mm 90 mm 145 mm Impact energy 145 mm connected load frequency 400 Volt total power requirement 1,5 kW weight of the machine ca. 0,2 t dimensions 1,43 x 0,72 x 1,7 m Miter band saw -Miter cuts up to 60° left -Vice with quick clamping device -Band tension control -Electr. Automatic cooling

Condition: new, cutting diameter 355 mm Gsdjmhm Aqopfx Abhsbi dimensions of saw-band 3770 x 34 x 1,1 mm cutting speed 20 - 80 m/min cutting width 490 x 280 mm 290 mm Impact energy 250 mm 230 mm 180 mm connected load frequency 400 Volt total power requirement 2,2 kW weight of the machine ca. 0,7 t dimensions 1,43 x 0,72 x 1,7 m Semi-automatic miter band saw - Miter cuts up to 45° left + right - Miter cuts up to 60° right - Vice with quick release device - Tape tension control via manometer - Electr. automatic cooling

Condition: new, cutting diameter 300 mm capacity 90 degrees: flat 330 x 260 mm capacity 90 degrees: square 260 x 260 mm capacity 45 degrees: flat 270 x 200 mm capacity 45 degrees: round 260 mm capacity 45 degrees: square 250 x 250 mm capacity 60 degrees: flat 170 x 170 mm capacity 60 degrees: square 170 x 170 mm capacity 60 degrees: round 180 mm turning speed range: 40 / 80 m/min dimensions of saw-band 3320 x 27 x 0,9 mm engine output 1,5 / 1,8 kW weight 670 kg Electro-hydraulic semi-automatic band saw SHARK 332 SXI EVO with semi-automatic-dynamic, manual function, has a MEP-28 control for miter cuts from 45° right to 60° left. Some features: New centralized switch console on an articulated arm. Low voltage control panel: Polyester membrane keyboard with thermoformed highlighted Push buttons and actuation control signal. Display to show: * Diagnostics (messages in the user language) * Alarms (description of alarm causes) * State of inputs and outputs * Counting cuts * Time taken for the cut made * Current consumption of the saw blade motor * Saw blade tension * Blade speed * Numerical display of head position. Switch handle IP55 of manual 24V cycle. Complete program of all special cutting cycles. Identification of other possible special cutting cycles for special ones Applications New, latest generation hydraulic control unit, extremely powerful and with low energy consumption. Turntable (on roller bearings of 420 mm with preloaded thrust bearings assembled). Double belt speed (40/80 m/min.) with control Intended to accommodate an electronic inverter for the Continuous regulation of the belt speed from 20 to 90 m/min. Gbodpfx Abjfg E H Uohoi Stroke of the saw bow can be programmed directly from the control panel Adaptation to the cutting material. Clamping device can be moved laterally to the left and right Quick release vice. Manually operated strap tension control with display on the screen electronic converter. Base designed to completely contain the coolant, even with maximum angle cuts. The coolant pan (provided with an electric pump for lubrication and Cooling of the saw band) and the chip drawer (can be replaced by a Chip conveyor to be replaced - see special accessories) are in the base frame built-in. Preparation for installing the minimum blade lubrication kit (Optional, in addition to the conventional standard lubrication with emulsion oil. Chip clearing brush. The machine is intended for pallet truck transport. Adjustable length stop for cuts of the same length Material support arm with roller for attaching the loading platform Bimetal saw band for solid and profile material. Tools and instructions for use in the respective user language.

Condition: new, cutting diameter 315 mm dimensions of saw-band 3460 x 1,1 x 34 mm cutting speed 35 / 70 m/min cutting width 400 x 250 mm 250 / 280 mm Godpfxewfyq Ts Abhsbi Impact energy 220 / 280 mm 180 mm 140 mm connected load frequency 400 Volt total power requirement 2,2 kW weight of the machine ca. 0,6 t dimensions 2,1 x 1,0 x 1,5 m Semi-automatic miter band saw - Miter cuts up to 45° left + right - Miter cuts up to 60° right - Vice with quick release device - Tape tension control via manometer - Electr. automatic cooling

Condition: new, cutting diameter 250 mm saw band length 3150 x 27 x 0,9 mm table height 700 mm cutting width 250 x 320 mm cutting speed 25 - 90 m/min dimensions of saw-band 2480 x 27 x 0,9 mm 120 mm 120 mm 190 mm Impact energy 190 mm connected load frequency 400 Volt total power requirement 1,5 kW weight of the machine ca. 0,5 t dimensions 0,95 x 1,16 x 1,98 m Rock-solid band saw for solid material Gbsdoff Efrepfx Abhei - Double miter cuts up to 60° - AutoCut - Vice with quick clamping device - Belt tension control - Electric automatic cooling system - Material suggestion

Condition: new, cutting diameter 300 mm saw band length 3320 x 27 x 0,9 mm table height mm band speed 40/80 m/min total power requirement 1,5/1,8 kW weight of the machine ca. 670 kg dimensions of the machine ca. m How it works in the CCS version: After the material has been advanced and Once the vices have closed, the cutting process begins. The lowering is done by its own weight and is controlled by a spring balanced and a hydraulic brake cylinder regulates when the cut is carried out, the saw arm is moved by hand to the necessary position for the feed of the material is pushed up. Electrical panel (marked cable connection, indicator light for Ready for operation, safety main switch provided with padlock, Switch or speed switch, emergency stop, thermal magnetic protection, Low voltage system 24 volts) Electronic tape tension converter with on-screen display. Manual vice with quick lock Base frame with coolant tray and chip drawer, which has a Motorized chip conveyor (accessory) can be replaced. Electric coolant pump for cooling and lubricating the saw blade. Chip clearing brush Adjustable precision stops to make cuts of the same length. Machine is intended for pallet truck transport. Bimetal saw band for solid and profile material Gbjdofg E H Tjpfx Abhoi Tools and instructions for use

Condition: new, cutting diameter 250 mm capacity 90 degrees: flat 280 x 220 mm capacity 90 degrees: square 220 x 220 mm vice 285 mm turning speed range: 36/72 m/min dimensions of saw-band 2950x27x0,9 mm total power requirement 1,5 / 1,8 kW weight of the machine ca. 485 kg dimensions of the machine ca. 1700 x 1000 x 1800 mm Electro-hydraulic semi-automatic band saw SHARK 282 SXI EVO with semi-automatic-dynamic, manual function, has a MEP-28 control for miter cuts from 45° right to 60° left. Semi-automatic function: At the start of the cycle: - Vice closes and motor starts – Saw head lowers for the cut – Motor switches off – Saw head rises – Vise opens. Semi-automatic dynamic system (manual lowering of the saw band bow up to to the desired position and cycle start via the manual button.) Some features: New centralized control console on an articulated arm to allow the operator can be easily switched from any working position. Low voltage control panel: Polyester membrane keyboard with thermoformed highlighted Push buttons and actuation control signal. Display to show: * Diagnostics (messages in the user language) * Alarms (description of alarm causes) * State of inputs and outputs * Counting cuts * Time taken for the cut made * Current consumption of the saw blade motor * Saw blade tension * Blade speed * Numerical display of head position. Switch handle IP55 of manual 24V cycle. Complete program of all special cutting cycles. Identification of other possible special cutting cycles for special ones Applications New, latest generation hydraulic control unit, extremely powerful and with low energy consumption. Large work surface with turntable on roller bearings, measuring 265 mm preloaded thrust bearing, mounted. Double belt speed (36/72 m/min.) with control Intended to accommodate an electronic inverter for the Continuous regulation of the belt speed from 20 to 90 m/min. Stroke of the saw bow can be programmed directly from the control panel Adaptation to the cutting material. Clamping device can be moved laterally to the left and right Quick release vice. Gbjdpfjfg E H Sex Abhoi Manually operated strap tension control with display on the screen electronic converter. Base frame with pull-out coolant tray. Electric coolant pump for cooling and lubricating the saw band. Preparation for installing the minimum blade lubrication kit (Optional), in addition to the conventional standard lubrication Emulsion oil. Chip clearing brush. The machine is intended for pallet truck transport. Length stop for cuts of the same length Material support arm with roller for attaching the loading platform Bimetal saw band for solid and profile material. Tools and instructions for use in the respective user language.

Condition: used, Year of construction: 1970, cutting diameter 250 mm saw band length 3660 mm cutting width 1,3 mm clamping range Länge 450 mm clamping range Höhe 250 mm cutting speed 20 - 70 m/min cutting capacity stufenlos Gjdpfxsxc Nwue Abhjbi mitter cutting - all-position 45 ° voltage 380 V frequency 50 Hz power capacity 0,55 kW weight of the machine ca. 0,7 t dimensions of the machine ca. 1,5 x 1,0 x 1,6 m coolant device

Condition: excellent (used), Danobat CP11.11 Horizontal Bandsaw Year 2009 Serial Number 0909901302 Max Size 1100mm x 1100mm Additional Features Year 2009 Variable Speed Front & Rear Tables Total Power 16kw Gbjdpjxwk Idjfx Abhoi Total Weight 10800kg

Condition: ready for operation (used), functionality: fully functional, cutting height (max.): 1,200 mm, cutting width (max.): 1,100 mm, Danobat CP 1211T Large Capacity Bandsaw Cutting Capacity Dia / Square 1100mm Cutting capacity rectangle 1200mm wide x 1100mm high Fully automatic Gbsdpfetv Nadjx Abhsi

Condition: reconditioned (used), Year of construction: 1982, functionality: fully functional, overall weight: 17,500 kg, working width: 1,300 mm, working height: 1,300 mm, working range: 1,300 mm, Amada H1300 Horizontal Bandsaw (1982) Gedstv E Hcjpfx Abhsbi Capacity 1300 x 1300mm Power 230 V – 50/60 hz / 400 v – 50hz / 460 v 60hz Blade drive 11 kw Hydraulic drive 3.7 kw Coolant drive 0.4 kw Wire brush drive 0.4 kw Blade size 11380mm x thickness 1.6 x width 65 mm Net weight 17.500 kgs Total power requirement 16 kw Machine Data: Model H1300 Year of Construction 1982 Built in Japan

Condition: like new (used), MJ442 Wood Band Saw Machine – 0.75 kW – 220V For sale: MJ442 wood band saw machine, suitable for woodworking shops, carpentry workshops, and small-scale furniture production. Compact and reliable machine, easy to operate, and ideal for precise wood cutting. Gjdpfx Ajyq N Nusbhobi Technical Specifications Model: MJ442 Motor power: 0.75 kW Power supply: 220 V / 50 Hz / 1 Phase Max cutting height: 650 mm Table size: 460 × 360 mm Machine dimensions: 1020 × 530 × 1050 mm Weight: approx. 200 kg CE certified Condition Machine is in good working condition and ready for use. Suitable for: - Carpentry workshops - Small woodworking shops - DIY woodworking