Used Hot Stamping Machine for sale (67,317)

Condition: new, Year of construction: 2026, functionality: fully functional, operating pressure: 6 bar, inner dimension width: 600 mm, inner dimension height: 400 mm, volume flow: 10,500 m³/h, Equipment: documentation/manual, New Wire Mesh Belt Shot Blasting Machine RB-600 AH 4 Description: The RB-600 AH 4 wire mesh belt shot blasting machine from ABRAZIV Kft. is designed for the economical and continuous surface treatment of small to medium-sized workpieces. The machine is suitable for descaling, derusting, cleaning, and surface preparation of aluminum and steel castings, forgings, and workpieces that cannot be shot blasted in bulk. The machine is manufactured to order and can be configured individually according to customer requirements. The RB-600 AH 4 is equipped with four ABR-380 shot blasting turbines. Two turbines are located above and two below the wire mesh conveyor belt. This arrangement ensures optimal coverage of the cross-section and a uniform blasting result. The turbines operate at an angle of approximately 70° to the direction of travel and have eight blasting blades and a pre-accelerator. The active blasting area is lined with highly wear-resistant manganese steel. Other internal areas are protected by wear-resistant, noise-reducing rubber. The wire mesh belt is made of highly wear-resistant spring steel. A closed blasting media circuit with a screw conveyor, bucket elevator, blasting media cleaning system, and dosing system ensures reliable operation. Three-layer rubber curtains reduce blasting media leakage. An adjustable high-pressure blow-off system cleans the workpieces after the blasting process. The extraction and filter system with cartridge filters achieves a dust emission of max. 3 mg/m³. Technical Data Passage Passage width: 600 mm Max. workpiece height: 400 mm Min. workpiece length: approx. 1,000 mm Shot Blasting Turbines Number: 4 Type: ABR-380 Turbine diameter: 380 mm Speed: 2,800 1/min Blasting media output per turbine: 120 kg/min Wire Mesh Conveyor Belt Load capacity: 500 kg/m Speed: 0–4 m/min Power Consumption Base machine: 45.5 kW Cartridge filter: 7.5 kW Compressed air: min. 6 bar Compressed air consumption filter: 12.5 m³/h Other Data Blasting media capacity: approx. 1,000 kg Blasting media grain size: 0.4–1.2 mm Extraction capacity: 10,500 m³/h Bdodpfx Agezkivtjksi Filter area: 252 m² Dust emission: max. 3 mg/m³ Electrical Data Mains voltage: 3 × 400 V Control voltage: 220 V Frequency: 50 Hz Optional accessories available Magnetic drum separator Frequency converter Automatic blasting media dosing Special paint finish Transport Assembly Commissioning Operator training Spare parts supply Maintenance and service Applications Aluminum and steel castings Forgings Small steel components Single and series components Descaling Derusting Cleaning Surface preparation Location / Production Lichtenfels (Germany) / Kecskemét (Hungary) As a manufacturer, we produce shot blasting machines individually according to customer requirements. Other sizes and special designs are available. We will be happy to provide you with a non-binding offer. Price on request

Condition: like new (used), functionality: fully functional, Year of construction: 2022, operating hours: 296 h, control type: CNC control, The Jinan Bodor P3T series is one of the manufacturer's most sought-after, fully enclosed industrial workhorses equipped with an automatic pallet changer. In addition to sheet metal processing, this machine is also designed for the precision cutting of tubes and profiles (T-version), allowing the entire production range to be covered with a single system.Dual Function: Flatbed sheet metal cutting and automatic tube cutting module in a single system. Maximum Safety: Fully enclosed protective cabin with laser safety glass for the complete protection of operators and the environment.Minimal Downtime: Automatic pallet changer system that enables loading and unloading during the cutting process.Outstanding Dynamics: High positioning speed and acceleration for maximum productivity.Intelligent Control: Bodor PRO. Technical Specifications: - Laser Source Power: 3000 W (3 kW) - Sheet Dimensions (X x Y): 3000 mm x 1500 mm - Tube Length Capacity: 6000 mm (6U execution) - Chuckable Tube Diameter: Ø20 mm – Ø170 mm (and corresponding square and rectangular profiles) - Chuck System: Automatic pneumatic / electric self-centering chucks - Control Software: Bodor PROPositioning - Accuracy: ±0.03 mm - Cuttable Materials and Guideline - Maximum Thicknesses (3 kW): Carbon Steel / Mild Steel: max. 20 mm Stainless Steel: max. 10 mm Aluminum: max. 10 mm Brass / Copper: max. 6 mm Accessories and Scope of Delivery: - Factory industrial water chiller unit Bodsznwu Sspfx Agkodi - Automatic voltage regulator / stabilizer - Extraction and dust filtration system - Automatic nozzle cleaner - Complete documentation and software licenses Condition and Inspection: - The machine has been continuously maintained and has a service history fully supervised by a specialized technician. It is currently in live production and can be inspected and tested under operating conditions by prior appointment. Subject to prior sale. Under power in Hungary.

Condition: used, Year of construction: 1997, Henkovac H 1000 – Industrial Vacuum Packaging & Sealing Machine (1997) The Henkovac B.V. H 1000, manufactured in 1997, is a robust industrial vacuum packaging and sealing machine designed for high-volume food processing environments. Built for reliability and durability, it is ideal for commercial kitchens, food processors, and manufacturing lines that require hygienic, efficient, and consistent vacuum packaging. Key Features: - Heavy-Duty Vacuum Packaging: Securely evacuates air from packages, extending product shelf life and maintaining quality. - Reliable Sealing: Ensures airtight seals for a variety of food products, including meats, cheeses, and prepared meals. - Industrial-Grade Construction: Designed for continuous operation in demanding food processing environments. - Versatile Application: Suitable for vacuum packaging of different types and sizes of food products. - Long-Term Reliability: Proven design ensures dependable performance even after decades of use. - User-Friendly Operation: Controls and interface designed for efficient workflow in industrial kitchens. Technical Highlights: - Manufacturer: Howden Food Equipment B.V. - Model: H 1000 - Year of Manufacture: 1997 - Machine Type: Industrial vacuum packaging and sealing machine Bdodpfxjyudxxo Agkoi - Applications: Food processing, commercial packaging, shelf-life extension Whether for high-volume production lines or specialized food processing tasks, the H 1000 delivers professional vacuum sealing performance, combining durability, hygiene, and reliability. More photos and full specifications: / * Manufacturer: Henkovac * Model: H 1000

Condition: excellent (used), Year of construction: 2012, XYZ SMX 4000 ProtoTRAK CNC Bed Milling Machine ProtoTRAK SMX Control Year of Manufacture 2012 Spindle: 7.5Hp – Programmable 70 – 5000rpm ISO40 Quill Dia 105mm Table: 1474 x 355mm Max load 850kgs Travel: X – 1,060mm Y – 596mm Z – 520mm Dims without travels: W - 2370mm D – 2485mm H – 2660mm Weight - 3100Kgs For Sale with Jet Machinery Ltd Jet Machinery Stock No: #79167 Machine Serial Number: 10836 Cost: £22,500.00 + VAT Whilst every effort has been made to ensure that the above information is accurate it is not guaranteed. We advise prospective purchasers to check any vital details. Health and Safety At Work Act 1974: It is not reasonably practical for ourselves as suppliers to ensure that for your application the goods comply with requirements of the Act with respect to guarding etc. Prospective purchasers should ensure that a guarding specialist inspect the goods prior to use. Bjdeyzf Najpfx Agkodi

Condition: used, Year of construction: 2021, functionality: fully functional, total length: 3,000 mm, total width: 700 mm, total height: 1,500 mm, type of input current: three-phase, overall weight: 250 kg, input voltage: 380 V, length stop: 3,000 mm, lifting height: 250 mm, We offer this used OZ MACHINE METEOR - II 420 lightweight aluminum circular saw, manufactured in 2021. Model: METEOR - II 420 Serial number: 018/210023 Year of manufacture: 2021 Total power: 3 kW Frequency: 50–60 Hz Voltage: 400 V AC 3P 1N PE Current: 6.4 A Dimensions (L×W×H): 3760×1080×1325 mm Weight: 264 kg Air pressure: 6–8 bar Air consumption: 38 l/min Idle speed: 3000 r.p.m. Saw blade diameter: 420 mm Includes dust extraction system and compressor. If you have any questions or require further information, please feel free to send us a message or call us. Bsdpfjzy Upkjx Agkjdi

Condition: excellent (used), Year of construction: 1992, functionality: fully functional, machine/vehicle number: 06651, travel distance X-axis: 6,800 mm, travel distance Y-axis: 3,700 mm, travel distance Z-axis: 1,500 mm, feed rate X-axis: 15 m/min, feed rate Y-axis: 15 m/min, feed rate Z-axis: 10 m/min, total length: 15,000 mm, total width: 7,500 mm, spindle speed (max.): 4,000 rpm, total height: 7,000 mm, table height: 1,100 mm, rapid traverse X-axis: 15 m/min, rapid traverse Y-axis: 15 m/min, rapid traverse Z-axis: 10 m/min, distance between stands: 3,300 mm, type of input current: three-phase, table load: 50,000 kg, rotational speed (max.): 4,000 rpm, distance table center to spindle nose: 2,110 mm, overall weight: 1,10,000 kg, spindle motor power: 50,000 W, control cabinet length: 7,000 mm, control cabinet height: 2,000 mm, control cabinet width: 600 mm, Equipment: rotational speed infinitely variable, MODEL: Portal Type AGE: 1992 S/N #: 06651 CATEGORY: Mills, Planer Type, CNC Bdsdpfx Ajyahv Ssgksi CAPACITY: X-Axis Travel: 6800 mm Y-Axis Head Travel: 3700 mm Z-Axis Ram Stroke: 1500 mm, fixed crossrail Ram Cross Section: 500 mm x 500 mm Distance Between Columns: 3300 mm Distance Table To Ram Face: 2110 mm, vertical passage 2000 mm Table Size: 6000 x 2500 mm Spindle (Quill) Diameter: 250 mm Spindle Taper: ISO #50 Spindle Speeds: 0-4000 RPM Spindle Motor: 50 KW EQUIPPED WITH: FIDIA System C20 CNC Control, new in 2002 CNC biaxial continous milling head Universal Milling Head with Auto Indexing Right Angle Head with Auto Indexing Straight Milling Head Wagons for Head Change and Tool Pick-up Change Hydrostatic Bearings Coolant System Full Length Chip Conveyors both side Way Covers Rapid movements: Z-10.000 mm/min, X and Y-15.000 mm/min Table load: max 50.000 kg Weight of the machine: 110.000 kg Outside dimensions: 15.000 x 7.500 x 7050 mm Machine has been tested before dismantling and is fully operational, all mechanical components in excellent condition, electrics new in 2018. Machine available from stock. The price is now SPECIAL FROM STOCK. Once we will reassemble the machine, price will grow significantly. We can assist you to assemble and run up the machine.

Condition: used, functionality: fully functional, Year of construction: 2021, operating hours: 2,300 h, machine/vehicle number: 921R50022874, control type: CNC control, degree of automation: automatic, laser type: fiber laser, laser source manufacturer: MAX photonics, laser power: 2,000 W, pipe diameter (max.): 200 mm, pipe length (max.): 6,000 mm, working length: 6,000 mm, travel distance X-axis: 6,500 mm, travel distance Y-axis: 360 mm, feed rate X-axis: 120 m/min, cutting speed: 1,600 mm/min, positioning speed: 120 m/min, positioning accuracy: 0.03 mm, repeat accuracy: 0.03 mm, input voltage: 380 V, input frequency: 50 Hz, type of input current: three-phase, type of cooling: water, overall weight: 14,700 kg, total length: 12,500 mm, total width: 4,700 mm, total height: 2,600 mm, tube wall thickness (max.): 6 mm, Equipment: cooling unit, emergency stop, fume extraction, safety light barrier, Laser machine for sale, in very good condition. It has a new laser source that is only a few months old. The machine has few operating hours and has been regularly maintained and is in daily use. It is possible to inspect and test the machine immediately upon arrangement. Bjdpfxozg D I As Agkjdi NOTE: Capable of cutting round, square, rectangular, oval, D-shaped, and U-shaped tubes.

Condition: ready for operation (used), Year of construction: 2003, functionality: fully functional, turning diameter over cross slide: 272 mm, turning length: 1,250 mm, turning diameter: 470 mm, spindle bore: 80 mm, spindle speed (max.): 2,500 rpm, spindle speed (min.): 50 rpm, travel distance X-axis: 1,250 mm, rotational speed (min.): 50 rpm, rotational speed (max.): 2,500 rpm, total height: 1,850 mm, total length: 2,700 mm, total width: 1,350 mm, type of input current: three-phase, overall weight: 2,300 kg, XYZ Proturn CNC/Manual Lathe Model: Proturn 410 Control: Proto Trak LX2 Swing Over Bed: 470mm Swing In Gap: 730mm Swing Over Cros Slide: 272mm Distance Between Centres: 1250mm Spindle Speeds: 50-2500 RPM Spindle Bore: 80mm Machine With: 300mm 3 Jaw Chuck Bdodpfxezux Iyj Agksi Quick Change Toolpost with Holders Dimensions: 2700 x 1350 x 1850mm high Weight: 2300 Kgs

Condition: excellent (used), Year of construction: 2023, 400mm swing, 220mm max diameter, 490mm between Centres, Siemens 828 Control, 65mm bar capacity, 12 station VDI30 turret, 17kW Spindle Motor, Spindle Speed 4000rpm, Bjdpfx Agez Srv Djkjdi 0.001 degree C axis, +/- 35mm Y axis, low volt light, coolant, Tool setter, Tailstock, swarf conveyor

Condition: new, functionality: fully functional, Year of construction: 2026, control type: CNC control, degree of automation: semi-automatic, actuation type: electric, controller manufacturer: Bodor, laser type: fiber laser, Applicable Material: metal Condition: New Laser Type: Fiber Laser Cutting Area: 3000*1500mm Cutting Speed: 0-40000mm/min Bedpjg Ev T Esfx Agkodi Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT Cutting Thickness: 0-30mm CNC or Not: Yes Cooling Mode: WATER COOLING Control Software: Bodor Pro Place of Origin: China Brand Name: Bodor Certification: CCC, CE, GS, ISO, Sgs Laser Source Brand: IPG/MAX Laser Head Brand: bodorgenius Control System Brand: bodorpro Weight (KG): 2200 KG Key Selling Points: Tenon-and-mortise type plate welding structure bed Warranty: 3 years Laser power: 1000W Power supply: 110V/220V/380V 50Hz/60Hz

Condition: new, Screen Bucket for 20-25tons Excavators Galen screen bucket is a versatile and efficient attachment designed specifically for infrastructure and construction projects. It allows on-site material sorting, reducing the need for additional transport and processing equipment Bedpfjw Dayrex Agkodi

Condition: excellent (used), Year of construction: 2014, operating hours: 11,440 h, DMG 5 axis Simultaneous HSC 30 Linear Year 2014 Heidenhian TNC640 Control Travel X320 / Y 300 / Z280mm B axis +/- 120 degree C axis 360 x 0.001 degree HSK-E40, 40,000rpm Swivel rotary table Touch Probe BLUM Tool Measuring system Bdsdpfx Agjw Hxiwskei 3D Quick Set Application Tuning Cycle Air Blast through spindle Super Fine filter system c/w tooling ----- Clearance Sales -----

Condition: new, functionality: fully functional, power: 11 kW (14.96 HP), Year of construction: 2025, A spiral-type sand washer machine, also known as a spiral sand washing machine or screw sand washer, is a piece of equipment designed for washing, classifying, and dewatering sand and other granular materials. This type of sand washer typically features a spiral or screw-shaped structure for the purpose of lifting, conveying, and washing materials. Here are key features and aspects of a spiral-type sand washer machine: 1. Spiral Structure: The core component of the machine is a spiral or screw-shaped structure, often enclosed within a tub or trough. This spiral impeller is responsible for lifting, conveying, and washing the sand as it rotates. Bdjdpfx Aeq Nf S Rjgkoi 2. Tub or Trough Design: The spiral structure is usually housed within a tub or trough that holds the water and sand mixture. This design allows for efficient washing and separation of impurities from the sand. 3. Multiple Blades: The spiral impeller typically has multiple blades or flights that provide mechanical agitation to the sand, ensuring thorough cleaning. 4. Water Injection: Water is injected into the tub or trough to aid in the washing process. The combination of water and the rotating spiral helps to remove impurities from the sand. 5. Adjustable Weirs: Some spiral-type sand washers have adjustable weirs or gates that control the flow of water and the retention time of the sand in the machine, allowing for customization of the washing process. 6. Classification and Dewatering: Spiral sand washers often include features for classifying and dewatering the sand. This may involve the use of a separate compartment or mechanism for fine sand recovery and water drainage. 7. Variable Speed: The rotational speed of the spiral can often be adjusted to optimize the washing process for different types of materials and particle sizes. 8. Capacity: The capacity of a spiral-type sand washer is influenced by factors such as the size of the machine, the pitch of the spiral, and the efficiency of the washing process. Different models are available to suit various production requirements. 9. Materials Handling: Spiral sand washers are commonly used in applications such as aggregate processing, mining, concrete production, and other industries where the removal of impurities from sand is essential. 10. Ease of Maintenance: Many spiral-type sand washers are designed for easy maintenance, with accessible components and inspection points. Spiral-type sand washer machines are efficient tools for cleaning and processing sand, ensuring that the final product meets quality standards for use in construction, concrete production, and other applications. The specific features and capabilities of these machines can vary between different models and manufacturers.

Condition: used, Perfectly working grinding machine "станка 3Л722" Basic parameters Accuracy class A Maximum workpiece dimensions (length x width x height) 1250 x 400 x 400 Maximum dimensions on electromagnet 1250 x 400 x 280 Minimum dimensions on electromagnet 50 x 40 x 3 Distance from the spindle axis to the table mirror mm 210..625 Maximum product weight kg 600 Maximum weight on electromagnet 400 Machine work table Dimensions of table work surface (length x width) 1000 x 400 Table feed speed 3..35 Grinding head Dimensions of grinding wheel ПП450х80х203 Grinding wheel speed/min 1460 Bjdpfx Ajqwzt Nogkjdi Maximum grinding speed m/s 34.4 Maximum diametrical feed, mm 430 Accelerated transverse disc feed m/min 1,2 Automatic cross feed for each table feed mm/rev 1..60 Maximum vertical disc feed, mm 415 ?? 0,002 ?? 0,2 Automatic vertical disc advance, mm 0,002..0,128 Vertical accelerated advance speed, m/min 0,2 Electrical equipment Number of motors 13 Disc spindle motor power, kW 11 Hydrostatic pump motor power 4 Hydrostation air heat exchanger motor power 0,09 Lubrication system pump power 0,25 If you have any further questions, we will be happy to answer them.

Condition: used, Year of construction: 2005, functionality: fully functional, Manufacturer: Hardinge / Bridgeport (USA / UK) Model: XP1000 Year of Manufacture: 2005 Reliable and efficient CNC vertical machining center designed for milling, drilling, and tapping a wide range of metal components. Bsdpoxqprujfx Agkjdi The Bridgeport XP series is renowned for its robust construction, high precision, and fast processing capabilities, making it ideal for both job shop and series production. Main technical specifications: (based on Hardinge Bridgeport XP1000 specification) Control: Heidenhain iTNC 530 Travel: X = 1020 mm / Y = 510 mm / Z = 635 mm Table size: 1200 × 520 mm Max. table load: 700 kg Spindle speed: up to 10,000 rpm Spindle taper: BT40 Tool changer: 20 positions (automatic) Spindle motor: 15 kW Machine weight: approx. 7,000 kg Power supply: 400 V / 50 Hz Cooling system: integrated Application: The Hardinge Bridgeport XP1000 is designed for precision metalworking—milling, drilling, tapping, and contour machining. Ideally suited for: - Tool, mold, and component manufacturing - Automotive, equipment, and industrial sectors - Situations requiring accuracy, reliability, and consistent performance If you have any further questions, we will be happy to assist you.

Condition: used, Year of construction: 2005, CNC Machining Center HARDINGE BRIDGEPORT XP610 (Year 2005) Condition: Good, technically sound. Manufacturer: Hardinge / Bridgeport (USA / UK) Model: XP610 Year of manufacture: 2005 A compact and reliable CNC vertical machining center designed for precise milling, drilling, and tapping of metal parts. The Bridgeport XP series is known for its high accuracy, robust construction, and reliable control system, making it an excellent solution for manufacturing processes where precision and repeatability are crucial. Main technical specifications: (according to Hardinge Bridgeport XP610 model specifications) Control system: Heidenhain iTNC 530 Travel (X / Y / Z): 610 × 510 × 510 mm Table size: 800 × 520 mm Max. table load: 500 kg Bedjxqp Enspfx Agksdi Spindle speed: up to 10,000 rpm Spindle taper: BT40 Tool changer: 20 positions (automatic) Spindle motor: 11–15 kW Cooling: integrated coolant system Power supply: 400 V / 50 Hz Machine weight: approx. 6,000 kg Application: The Hardinge Bridgeport XP610 is designed for precision machining of components and parts: - Metal, aluminum, copper, and brass workpieces - Tool and die manufacturing - Production of mechanical components and industrial parts Suitable for both small batch and series production where a precise, stable, and repeatable result is required. If you have any further questions, please feel free to contact us.

Year of construction: 2021, condition: excellent (used), For sale: Metal Stamping Press ALP-25J (25T, 2021) Condition: Virtually unused, like new. Manufacturer: JINAOLAN Machinery (China) Model: ALP-25J Year of manufacture: 2021-04 Bdedpjxm U S Sjfx Agkoi A compact and reliable mechanical eccentric stamping press designed for forming, punching, and stamping a wide range of metal components. Technical specifications: Nominal capacity: 25 T Stroke: 100 mm Stroke rate: 100 strokes/min (SPM) Max. die height: 260 mm Height adjustment: 55 mm Ram working area: 560 × 370 mm Bolster area: 250 × 220 mm Country of origin: China Applications: The ALP-25J press is suitable for: - Stamping, cutting, bending, and forming metal components - Small press operations in tool, metal structure, and automotive part manufacturing - Working with thin and medium-thickness sheet metal If you have any further questions, we will be happy to answer them.

Condition: new, Year of construction: 2025, Entry-level fiber laser metal sheet&tube cutting machine One machine with two uses. AT series cuts both metal sheets and metal tubes. The modular cutting machine table with stiffeners saves time for disassambly and improves convenience and rigidity. Cutting machine clamping becomes convenient, easy and fast, with 3 seconds at the soonest to clamp and high repeat precision Fast air cutting efficiency increases by 37% when cutting carbon steel. Fiber laser heads are able to detect jutting obstacles to effectively reduce the damage rate and save the maintenance cost of a laser cutter. Angle steel and channel steel cutting are standard with no need fior additional installation. Bdjdpehv U Txofx Agkoi Condition: New Laser Type: Fiber Laser Laser Power: 1000W, 1500W, 2000W, 3000W Cutting Area: 3048*1524mm Cutting Speed: 0-100m/min Positioning accuracy: ±0.03mm Repositioning accuracy: ±0.02mm Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING

Year of construction: 2023, condition: new, Cut to length machines FORSTNER COMPACT functions: - straightening (rolls diameters 70 mm) - slitting (max 7 slitting knives) - cutting (guillotine or roller shear) Bdsdpfx Ajiy N I Iegksi Available coil width - 1250 or 1500 mm

Condition: excellent (used), Filling machine, TM Industry Belgium, Model M 25 Bjdpoiu H Uvofx Agksdi For filling liquids Filling range: 0.5 - 30 kg In very good condition, directly from production!!!

Condition: new, Year of construction: 2021, Layout: Round bale grab Empty weight: 7.500 kg Attachment suited for: Lifting equipment Capacity: 32 M.T. Jaw Aperture(min-max): 160mm/2400mm Jaw Teeth Length: 200mm Open/Close Time: ~7,5 sec Axial Rotation Time: ~30 sec Axial Rotation Time: 270° Weight: 7500kg Crane Hook Type: DIN 15401 No:40 hook Bodpfx Agjpa Rmkokjdi Ambient Temperature: 45 ºC Max. Coil Temperature: 1100 ºC Energy Supply Voltage: 400 VAC, 3 Faz, 50 Hz

Condition: new, Year of construction: 2023, construction height: 22,000 mm, Explore Galen Group's range of high-quality long reach boom-arms, designed to enhance operational efficiency and safety in challenging construction environments. The machine details on the photo Machine Model: Komatsu PC450 Total Length:22m Bucket Capacity: 1m^3 Usage Area: Port Construction Bodsq E Iw Ropfx Agkjdi For detailed information and inquiry, please contact us

Condition: new, functionality: fully functional, Year of construction: 2027, pipe diameter (max.): 38 mm, bending angle (max.): 190 °, bending radius (max.): 220 mm, total length: 4,250 mm, power: 19 kW (25.83 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, warranty duration: 24 months, drive type: Servo - Hydraulic, operating speed: 147 mm/s, pressure: 150 bar, wall thickness: 2 mm, working length: 3,600 mm, Equipment: documentation/manual, 38x2mm Fully Automatic Cnc Tube Bending Machine The "Griffin" tube bending machines are hybrid structures. This type of tube benders includes hydraulic and pneumatic for clamping operations. Bending, feeding, rotation, stack changer and tube aligment operations working with servo engine. Flexible bending and working capacity with CNC control system. The capacity to adjust molds in 3 different radius scales Ability to automatically convert 3D technical drawings to bending program Multivariable roll bending system Ability to work with or without a mandrel Automatic oil cooling system With linear guideway systems minimize the system gaps in moving parts Program changing feature while in the bending process Bodpfx Agjvurm Hoksdi ETU bending simulation program, for bending process, helps to make 3d tube bending arising from the coordinates, with excellent results. With DcOnTool tool, you can convert X, Y, Z coordinates to bending program (Y,B,C) Can review the last error messages with Dlog Its user-friendly, easy, knowledgeable and quick-to-learn design allows you to start the project quickly. Easy to use with 17 inch computer. The vibration-free structure shall help your work. Unlimited program saving and changing Turkish – English and French language 10 years sending spare parts

Condition: like new (used), functionality: fully functional, Year of construction: 2024, control type: CNC control, degree of automation: automatic, actuation type: electric, For sale: lightly used sheet metal rewinding machine SVM-100, designed for automatic rewinding of sheet metal from large coil rolls into smaller rolls of 25m2 (1250*20,000 mm). The machine was manufactured in 2024, has been used very little, is in excellent technical and visual condition, and is fully ready for operation. It is an excellent solution for companies that produce roofing materials or other sheet metal products supplied in rolls. The machine automatically: - Unwinds the sheet metal from the coil up to 1 ton. If you want to rewind from 2-5 ton coils, an automatic unwinding unit is required to feed the sheet metal. - Winds the sheet metal into a roll. - Cuts the sheet to a specified length. - Allows the roll to be wrapped with stretch film. - Applies protective film to the surface of the sheet metal. The machine is connected – it can be inspected and tested. Technical specifications: Manufacturer: Foldsolutions / UAB Pakservisas Model: SVM-100 Year of manufacture: 2024 Made in: Lithuania Operating parameters: Sheet metal width: 1230–1260 mm Sheet metal thickness: 0.4–0.6 mm Maximum roll length: 20 m Roll diameter: approx. 300 mm Equipment: Automatic sheet metal winding Sheet metal cutting to a specified length Automatic roll packing process with stretch film Option to use protective film on the sheet metal Integrated length measuring encoder Touchscreen control panel Manual and automatic operating modes Pneumatic cutting system Adjustable operating speeds Length calibration function for precise production Emergency stop system Bedpezibwgsfx Agksdi Technical data: Electrical power: 400 V / 50 Hz / 3 phases Power: 2.6 kW Required compressed air pressure: 0.65 MPa Air consumption: 0.3 m³/min Dimensions (L × W × H): 2555 × 1730 × 1800 mm Weight: approx. 600 kg Application: Ideally suited for roofing materials, facade, sheet metal products, sheet metal processing companies, and other manufacturers who require fast, accurate, and safe preparation of sheet metal rolls for transport or storage. If you have any further questions, we will be happy to answer them.

Condition: new, functionality: fully functional, Year of construction: 2026, table length: 3,200 mm, table width: 900 mm, power: 22 kW (29.91 HP), pressing force: 220 t, operating speed: 120 mm/s, reverse speed: 120 mm/s, stroke length: 470 mm, throat depth: 400 mm, Equipment: safety light barrier, Machine type Electro-hydraulic servo numerical control bending machine Order Type Non-Standard Basic parameter Pressure 220t Workbench length 3200mm Workbench height 900mm Column spacing 2500mm Throat depth 400mm Slider stroke 200mm Maximum opening height 470mm Fast descent speed 120mm/s Return speed 120mm/s Work speed 10mm/s Bodpfx Agjzgzt Njkodi Rear gauge (X-axis travel) 550mm Maximum operating speed of the X-axis 400mm/s X-axis positioning accuracy ±0.05mm X-axis repeat positioning accuracy ±0.02mm Y-axis positioning accuracy ±0.02mm Y-axis repeat positioning accuracy ±0.01mm R-axis stroke 100mm Maximum operating speed of the R-axis 100mm/s Working accuracy: Straightness ±0.2mm/m, angularity ±0.5°/m KW Main motor power (servo motor) KW 22KW Rated power (servo motor) KW 25.03KW Fuel tank capacity 200L Oil product model 46# Hydraulic Oil" Overall dimensions (length * width * height) 4200mm*1950mm*2700mm Weight 12T