Used Hydromec Avtocating for sale (51)

Condition: used, axle configuration: > 3 axles, first registration: 01/1985, total width: 3,780 mm, total height: 3,330 mm, Special low loader for heavy transport, payload of approx. 60,000 kg to 80,000 kg depending on use, whether on the road or internally, length of the loading area with slope approx. 12,400 mm, width 3,200 mm, widening to 3,700 mm, hydraulic axle compensation mm, hydromechanical steering on 6th axle (front + rear), 4 x hydraulic support cylinders, hydraulic ramp front + rear, loading possible from both sides, trailer coupling on both sides, ideal for pushing or transporting in tight spaces, vehicle can be covered with advertising and/or labeled Ledpfewkzw Ssx Aaneak

Condition: used, overall weight: 92,000 kg, axle configuration: > 3 axles, first registration: 08/2006, loading space length: 19,000 mm, loading space width: 3,000 mm, loading space height: 815 mm, total width: 3,000 mm, Equipment: ABS, Goldhofer STZ-H6-57/80A telescopic low loader for wagon transport----                                     Approval          Technical 1 Speed:     80km/h                 65km/h Fifth wheel load:               23,000kg               26,000kg Rear axle load:       10,000kg             11,000kg Total weight:     83,000kg               92,000kg Payload:                52,500kg               61,500kg Own weight: (without accessories):           30,500kg ----Gooseneck: Length: 4,000mm Width: 2,480mm Height: 235mm Seat height: 1,350mm DLR front: 1,420mm DLR rear: 2,700mm King pin 3.5 inches Bevel: bevelled 10 degrees Corners front: bevelled 45 degrees Floor covering: spruce 50mm Seat supports: mechanical Width with side walls: 2,550mm Hydraulic STZ gooseneck with external supports, hydraulically liftable and lowerable with mechanical downpipe supports and hydraulic support cylinders hydromechanical forced steering (2-circuit steering) in flat design (height 235mm) with adjustable guide elements and THP steering cylinders. ----Loading area: Type: Platform Liftable: no Length: 13,000mm Width: 3,000mm Floor covering: sheet metal/spruce 50mm Wheel recesses: no Wider extensions: no Extendable: simply telescopic Length1: 10,000mm Loading heights (loaded) Loading height 1: 815mm Loading area telescopic, designed as an outer and inner tube construction, with 1,070mm long, fixed loading area section at the front. Bolt-link coupling integrated in the fixed loading area section for coupling boiler bridge extension supports, the square rails welded on by us serve as rail tracks in the track widths 1,000 mm (rail spacing 1,015 mm) and 1,435 mm (rail spacing 1,450 mm). Locking of the extension steps by spring-loaded cylinders and conical bushings Loading area height on the frame center tube (outer tube) approx. 815mm (+/- 130mm) Loading area height on the enclosed rail elements approx. 790mm (+/- 130mm) ----Rear chassis: Chassis type: Standard Loading height: 815mm Width: 3,000mm Wheelbase: 1,360mm Floor covering: Sheet metal Extensions: no Wheel recesses: no Excavator recess: no ----Axles: Number of axles: 6 Lift axle: see accessories Axle type: cranked steering knuckle Axle compensation: hydraulic Axle make: BPW/Eco Driving positions: 1 Axle stroke (1) +/-: 130/130mm Axle stroke (2) +/-: 0/0mm Raising/lowering valve: Yes 1st axle can be suspended pneumatically with lifting bellows ----Steering: Number of steering axles: 6 Steering axle arrangement: all steered Steering angle max: 45° Steering type: Hydr. 2 circles----Tires: Dimension: 235/75 r 17.5 143/141 J Tires. Type: twin Rim type: discs Lsdpfolhn Aiox Aanjak Rim centered: centered ----Brake code: according to EU standard: Yes AGS: Yes ALB: Yes ABS: Yes with ABS del: No Parking brake: spring-loaded EBS: No ECAS: No Remark: Brake calculation no.: GH 4324S ----Chassis remark: Steering designed for the extended state with a larger steering angle of the front axles Open wheel cutouts above the wheels with narrow cross arms in between (ALU covers see accessories below) Control elements protected on the left in the direction of travel Rims 17.5x 6.75 Cranked axles!!! ----Rear of vehicle: Design: Standard 90° Ramp fastening: see accessories Floor covering: Sheet metal Overhang from last axle: 1,300mm Support: see accessories ----Load securing: Lashing rings Number: 5 Loadable up to: 10 tons per piece Arrangement: 2 pairs on the SH                         3 pairs on the LF----Rear extension: Max. load capacity 15,000kg with a

Condition: used, maximum load weight: 1,75,620 kg, overall weight: 2,19,000 kg, axle configuration: > 3 axles, first registration: 01/2002, Equipment: ABS, STHP 8 (3 + 5) 8 units of hydraulic BWP pendulum axle assemblies with remote control. Technically permissible gross weight 219,000 kg Technically permissible payload 175,620 kg Hydraulically suspended, 8-axle steered Goldhofer low-bed heavy-duty trailer type STHP 8 (3+5), consisting of 4 heavy-duty modules with a detachable gooseneck and extendable excavator low-bed section up to 5 meters, featuring 4 wheel recesses, ABS, technically permissible payload up to 175,620 kg. Consisting of the following 4 separate heavy-duty module parts: 1st module: Hydraulic universal gooseneck type STH/ST Year of manufacture: 2002 Can be combined with heavy-duty module undercarriages, drivable loading platforms. Unladen weight approx. 5,900 kg Permissible front fifth wheel load: 35,000 kg Length approx. 4.10 m Fifth wheel height approx. 1.30 m King pin 3.5" pin Removable aluminum side walls Fully hydraulically adjustable 2nd module: Goldhofer THP/ST3 3-axle heavy-duty module First registration: 14.11.2001 As a single module, technically permissible total weight: 108,000 kg, technically permissible axle loads: 36,000 kg at 5 km/h possible. Unladen weight: 10,350 kg As a single module, technical payload up to 97,650 kg at 5 km/h possible. 8 hydraulic pendulum axles, 24 wheels, tire size: 215/75/R17.5 Axle load: 25 t at 20 km/h Vehicle width: 3 meters Axle spacing: 1.5 meters Max. steering angle: ±60° Integrated into chassis: hydromechanical dual-circuit all-wheel forced steering with a maximum aggregate steering angle of 60°, integrated hydraulic oil tank Optimized bolt-lug coupling at front and rear for longitudinal combinations Single-tired pendulum axle assemblies with a total of 8 wheels per axle line Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure suspension Hydraulic steering for all axles BPW axles with drum brake and ABS, technically permissible axle load of 34 t at 5 km/h 3rd module: Extendable low-bed heavy-duty module - Excavator bridge Year of manufacture: 2002 Internal dimensions approx. 7.50 meters long, 3.00 meters wide, loading height 0.40 meters Construction height 350 mm Extendable by approx. 5.00 meters - telescopic 4 wheel recesses with drive-on module at the front Construction height in wheel recess area approx. 150 mm Load capacity up to 80 t in low-bed and 175.6 t in overall STHP8 (3+5) module possible. Unladen weight 11,900 kg Front and rear hydraulic bolt-lug coupling with claw coupling adapter 4th module: Goldhofer THP/ET5 5-axle heavy-duty module First registration: 04.01.2002 Technically permissible total weight: 115,000 kg, technically permissible axle loads 23,000 kg at 5 km/h possible Unladen weight: 14,200 kg Technical payload up to 100,800 kg possible. Single-tired hydraulic pendulum axle assemblies with 4 wheels per axle line, 20 wheels (tire size 285/70 R 19.5) Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure suspension Hydraulic steering for all axles Remote control for steering axles 5. Notes: With the 4 heavy-duty modules, up to 3 different tractor combinations are possible! Payloads change depending on the configuration. For the special low-bed combination, a current manufacturer's certificate from Goldhofer is available. The low-bed trailer can be tested at our facility. Price NET excluding 19% VAT. All information without guarantee. Subject to errors and prior sale. Internal vehicle number: 2285 Lasdpfsxwgngsx Aanjk

Condition: new, More technical data on request Lodpfx Aaerz Uy Tjnjak Standard Features 1,2 mt Roller Table Saw Blade Brush Heavy Duty Gearbox Hydraulc Vce Hydromechnic Blade Tension Security Switch Inverter Control Panel Mechanic Top Clamping Coolant Pump Height  Adjustment Switch Saw Blade 34

Condition: like new (used), Year of construction: 2020, operating hours: 18,000 h, functionality: fully functional, As-new Gear Grinding Machine KLINGELNBERG VIPER 500 W All-inclusive machine equipped for internal and external gearing Equipped with a special converter from EUR kW to US standard connection (simplified global connection) Available due to restructuring at a high-tech family-run company (no automotive production) Working Area and Capacities Max. workpiece diameter: 500 mm Max. grinding stroke: 500 mm Working area over table (min.–max.): 300 – 800 mm Distance between spindle center and table (min.–max.): 442 – 1042 mm Module (generating grinding module): 0.5 – 22 Swivel angle (min.–max.): –180° to +45° Grinding System Grinding wheel diameter (min.–max.): 221 – 350 mm Grinding worm diameter (min.–max.): 221 – 350 mm Max. grinding wheel width: 75 mm Max. grinding worm width: 150 mm Grinding spindle power: 37 kW Max. grinding wheel speed: 6000 rpm Table and Feeds Table diameter: 400 mm Table bore Ø × depth: 100 × 500 mm Max. table speed: 1000 rpm Max. axial feed: 20,000 mm/min Max. radial feed: 12,000 mm/min Max. tangential feed: 20,000 mm/min Connections and Dimensions Total connected load: 60 kVA Machine dimensions (L × W × H): 4220 × 3120 × 2526 mm Filter unit dimensions (L × W): 3490 × 2250 mm Net weight approx.: 19,300 kg Machine Configuration – VIPER 500 W Base Machine and Options VIPER 500 W base machine Preparation for internal grinding arms Internal grinding unit V5 for straight or helical internal gears Measuring system for profile, lead, and pitch of external gears Measuring system for profile, lead, and pitch of internal gears V5 Touch Trigger Phasing System Power supply with ESR voltage drop compensation 100 mm table adapter Preparation for hydraulic clamping devices Hydromechanical unit for drawbar clamping systems Grinding oil filtration system with band filter 100 Fire extinguishing system Automatic work area door Cleaning system with spray gun Crane/hoist integrated into enclosure Isolation transformer Voltage stabilizer and isolation transformer Signal light/beacon tower Software Packages Gear PRO software Software for grinding of spline shafts Software for testing of spline shafts BIAS control software for gear grinding CBN grinding wheel software ADI dressing process optimization DLC lifetime monitoring for dressing tools Flexible profile correction for grinding operations Consumables Endless filter band Assembly/disassembly aid for filter band 100 Diamond dressing rollers CVD dressing roller D200 R1 for profile grinding CVD special dressing roller for generating grinding Grinding wheels Grinding wheel D350 B60 for profile grinding Grinding wheel D350 B45 for profile grinding Profiled grinding wheel D350 B150 for generating grinding Distance rings/intermediate plates Laodpexx T N Tofx Aanek 4 intermediate plates B100 22 intermediate plates B60 30 intermediate plates B45 37 intermediate plates B30 Additional Components Grinding wheel flange without intermediate plate Set of standard probes / measuring probes Additional Options Warranty extension from 12 to 24 months Closed Loop 1.0 basic version Interface for external automation

Condition: good (used), Year of construction: 2009, Cutting Capacity 0° 350 mm Diameter 570 x 260 mm Rectangle 350 mm Square +45° 350 mm Diameter 460 x 180 mm Rectangle 350 mm Square Standard Features Saw Blade 34 Inverter Roller Table Metarial Limit Shaft Securty Switch Laedpfx Aaorkz E Honjk Control Panel Height Adjustment Switch Hydromechnic Blade Tension Coolant Pump Saw Blade Brash Heavy Duty Gearbox

Condition: new, maximum load weight: 36,500 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete inventory of immediately and short-term available vehicles on our website. Excerpt from the equipment features. Full equipment list available upon request. - Gooseneck, approx. 4,100 mm in length with central beam - Load platform with double-extendable design, length approx. 9,400 mm - BPW axles and suspension - All axles hydromechanically forced-steered - Technical axle load: 12,000 kg - Air suspension with raise and lower valve Lasdpfx Aewvzg Rjanjk - Twin tires 235/75 R 17.5 3PMSF - WABCO braking system, EBS-E - 3 kW electro-hydraulic unit for hydraulic operations. Without installation of supply connections on the tractor unit - 4 pairs of stake pockets integrated in the outer frame of the gooseneck, suitable for insertable stakes approx. 100 x 50 mm - 2-inch king pin - 8 pairs of stake pockets integrated in the outer frame of the loading area, suitable for insertable stakes approx. 100 x 50 mm - 1 lockable INOX toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the loading platform on the left-hand side in direction of travel - Remote steering control from front and rear using cable remote with push buttons, with axle tracking control, without installation in the tractor unit - 2 axle load gauges mounted on the left side - Steel front wall, approx. 1,600 mm high - 3 transverse rows of stake pockets mounted in the floor of the loading area for insertable stakes approx. 100 x 50 mm - 1 transverse row of stake pockets mounted in the floor of the gooseneck for insertable stakes approx. 100 x 50 mm - 1 additional lockable INOX toolbox, mounted under the loading area - WADER container pockets in the loading area for transporting: 2x 20' containers or 1x 40' container - Central automatic lubrication system with 2 pumps, BEKAMAX brand - Complete HRM Metalization (High Resistance Metallisation)

Condition: used, overall weight: 92,000 kg, axle configuration: > 3 axles, first registration: 08/2006, loading space length: 19,000 mm, loading space width: 3,000 mm, loading space height: 815 mm, total width: 3,000 mm, Equipment: ABS, Goldhofer STZ-H6-57/80A telescopic low loader for wagon transport----                                     Approval          Technical 1 Speed:     80km/h                 65km/h Fifth wheel load:               23,000kg               26,000kg Rear axle load:       10,000kg             11,000kg Total weight:     83,000kg               92,000kg Payload:                52,500kg               61,500kg Own weight: (without accessories):           30,500kg ----Gooseneck: Length: 4,000mm Width: 2,480mm Height: 235mm Seat height: 1,350mm DLR front: 1,420mm DLR rear: 2,700mm King pin 3.5 inches Bevel: bevelled 10 degrees Corners front: bevelled 45 degrees Floor covering: spruce 50mm Seat supports: mechanical Width with side walls: 2,550mm Hydraulic STZ gooseneck with external supports, hydraulically liftable and lowerable with mechanical downpipe supports and hydraulic support cylinders hydromechanical forced steering (2-circuit steering) in flat design (height 235mm) with adjustable guide elements and THP steering cylinders. ----Loading area: Type: Platform Liftable: no Length: 13,000mm Width: 3,000mm Floor covering: sheet metal/spruce 50mm Wheel recesses: no Wider extensions: no Extendable: simply telescopic Length1: 10,000mm Loading heights (loaded) Loading height 1: 815mm Loading area telescopic, designed as an outer and inner tube construction, with 1,070mm long, fixed loading area section at the front. Bolt-link coupling integrated in the fixed loading area section for coupling boiler bridge extension supports, the square rails welded on by us serve as rail tracks in the track widths 1,000 mm (rail spacing 1,015 mm) and 1,435 mm (rail spacing 1,450 mm). Locking of the extension steps by spring-loaded cylinders and conical bushings Loading area height on the frame center tube (outer tube) approx. 815mm (+/- 130mm) Loading area height on the enclosed rail elements approx. 790mm (+/- 130mm) ----Rear chassis: Chassis type: Standard Loading height: 815mm Width: 3,000mm Wheelbase: 1,360mm Floor covering: Sheet metal Extensions: no Wheel recesses: no Excavator recess: no ----Axles: Number of axles: 6 Lift axle: see accessories Axle type: cranked steering knuckle Axle compensation: hydraulic Axle make: BPW/Eco Driving positions: 1 Axle stroke (1) +/-: 130/130mm Axle stroke (2) +/-: 0/0mm Raising/lowering valve: Yes 1st axle can be suspended pneumatically with lifting bellows ----Steering: Number of steering axles: 6 Steering axle arrangement: all steered Steering angle max: 45° Steering type: Hydr. 2 circles----Tires: Dimension: 235/75 r 17.5 143/141 J Tires. Type: twin Rim type: discs Rim centered: centered ----Brake code: according to EU standard: Yes AGS: Yes ALB: Yes ABS: Yes with ABS del: No Parking brake: spring-loaded EBS: No ECAS: No Remark: Brake calculation no.: GH 4324S ----Chassis remark: Steering designed for the extended state with a larger steering angle of the front axles Open wheel cutouts above the wheels with narrow cross arms in between (ALU covers see accessories below) Control elements protected on the left in the direction of travel Rims 17.5x 6.75 Cranked axles!!! ----Rear of vehicle: Design: Standard 90° Ramp fastening: see accessories Floor covering: Sheet metal Ledpfx Aaolhn Afenjak Overhang from last axle: 1,300mm Support: see accessories ----Load securing: Lashing rings Number: 5 Loadable up to: 10 tons per piece Arrangement: 2 pairs on the SH                         3 pairs on the LF----Rear extension: Max. load capacity 15,000kg with a

Condition: used, maximum load weight: 1,75,620 kg, overall weight: 2,19,000 kg, axle configuration: > 3 axles, first registration: 01/2002, Equipment: ABS, STHP 8 (3 + 5) 8-piece hydraulic BWP pendulum axle units with radio remote control. Total weight technically possible: 219,000 kg Payload technically possible: 175,620 kg Hydraulically suspended and 8-axle steerable Goldhofer low-bed low-loader type STHP 8 (3+5) consisting of 4 heavy-duty modules with a detachable gooseneck and up to 5-meter-long telescopic excavator low-bed with 4 wheel recesses with ABS up to 175,620 kg payload technically possible. Consisting of the following 4 separate heavy-duty module parts: 1st Module: Hydraulic universal gooseneck type STH / ST Year of manufacture 2002 Can be combined with heavy-duty module chassis, with drive-over loading bridges. Empty weight approx. 5,900 kg Lasdpfx Ajxcdfgjanek Permissible fifth-wheel load front 35,000 kg Length approx. 4.10 m Fifth-wheel height approx. 1.30 m King Pin 3.5" bolt Aluminum side boards plug-in Fully hydraulically adjustable 2nd Module: Goldhofer THP/ST3 3-axle heavy-duty chassis module First registration: 14.11.2001 As a single module total weight technically possible: 108,000 kg, axles technically possible load: 36,000 kg at 5 km/h possible. Empty weight: 10,350 kg As a single module technical payload up to 97,650 kg at 5 km/h possible. Hydraulic pendulum axles 8-fold, 24 x fitted with tires: 215/75/R17.5 Axle load: 25 tons at 20 km/h Vehicle width: 3 meters Axle distance: 1.5 meters Max. steering angle: ±60° Hydromechanical 2-circuit all-wheel forced steering integrated into the chassis with a maximum steering angle of the axle units of 60° with integrated hydraulic oil tank Front and rear optimized bolt-lug coupling for longitudinal combinations Single-tire pendulum axle units with a total of 8 wheels per axle line Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure spring suspension Hydraulic steering of all axles BPW axles with drum brakes and ABS and technically possible axle load of 34 tons at 5 km/h 3rd Module: Extendable heavy-duty low-bed module - excavator bridge Year of manufacture 2002 Internal dimensions approx. 7.50 meters long, 3.00 meters wide and 0.40 meters loading height Construction height 350 mm Extendable by approx. 5.00 meters - telescopic 4 wheel recesses with ramp module in the front area Construction height in the wheel recess area approx. 150 mm Load up to 80 tons in the low-bed and 175.6 tons in the complete STHP8 (3+5) module possible. Empty weight 11,900 kg Front and rear hydraulic bolt lug coupling with claw coupling adapter 4th Module: Goldhofer THP/ET5 5-axle heavy-duty chassis module First registration: 04.01.2002 Technically possible total weight: 115,000 kg, axles technically possible load 23,000 kg at 5 km/h possible Empty weight: 14,200 kg Technical payload up to 100,800 kg possible. Single-tire hydraulic pendulum axle units with 4 wheels per axle line fitted 20x with 285/70 R 19.5 Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure spring suspension Hydraulic steering of all axles Radio remote control for steering axles 5. Notes: With the 4 heavy-duty modules, up to 3 different pull combinations are possible! The payloads change with different pull combinations. A current manufacturer's certificate from Goldhofer is available for the special low-bed combination. The low-bed can be tested at our facility. Price NET plus 19% VAT. All details provided without guarantee. Subject to changes, errors and prior sale. Internal vehicle number: 2285 Advertisement als

Condition: new, Year of construction: 2025, cutting width (max.): 700 mm, cutting height (max.): 350 mm, warranty duration: 12 months, power: 4 kW (5.44 HP), STANDARD FEATURES ·      HYDRAULIC VICE ·      VARIABLE SPEED CONTROL (INVERTER) ·      SAFETY SWITCHES ·      HYDROMECANIC STRIP TENSIONING ·      VARIABLE ANGLE CUTTING BETWEEN 0 AND 60 DEGREES (ROTATING HUB) ·      ANGLE TABLE ·      ADJUSTABLE HEAD LANDING SYSTEM ·      1 SAW BLADE ·      2 MATERIAL CARRYING TABLES ·      24 MONTHS MECHANICAL 12 MONTHS ELECTRICAL WARRANTY ·      COUNTRY OF ORIGIN: TURKEY ·      MODELS PRODUCED BETWEEN 220 MM DIAMETER – 3000 MM DIAMETER TECHNICAL SPECIFICATIONS 350 YDG Capacity 90° (mm) Capacity 90° (mm)  Round Round 350 mm Square Square 350 x 350 mm Rectangle Rectangle 350 x 700 mm Capacity 60° (mm) Capacity 60° (mm)  Round Round 200 mm Square Square 170 x 170 mm Rectangle Rectangle 140 x 230 mm Capacity 45° (mm) Capacity 45° (mm)  Round Round 350 mm Square Square 300 x 300 mm Rectangle Rectangle 330 x 250 mm Main Motor / Torque Main motor / Torque 4 kW Hydraulic Motor Hydraulic Motor 0.37 kW Ljdpfx Aasvva Tqonjak Coolant Motor 0.09 kW Band Saw Blade Size 41x1.3x5170 mm Material Feeding Height 811 mm Vice Maximum Opening 700 MM Vice Maximum Closing 0 MM Table Width Rolled Table Width 820 MM Height-Width-Length Height-Width-Length 2000x2780x2452 mm Weight Weight 1750 KG

Condition: not inspected (used), JAFO FYN 50 NB – CNC Vertical Milling Machine For sale is a CNC vertical milling machine from JAFO, model FYN 50 NB, year of manufacture 1988. The machine is fully operational and ideal for precise milling operations on workpieces up to 700 kg including clamping device. ⸻ Technical Data • Travel (X/Y/Z): 800 × 500 × 500 mm • Table working area: 500 × 1,400 mm • Number of T-slots: 7 • Slot width: 18 mm • Slot pitch: 63 mm • Max. longitudinal table travel: 800 mm • Max. vertical knee travel: 500 mm • Max. transverse spindle head travel: 500 mm • Feed rate: stepless 0–4,000 mm/min • Spindle taper: ISO 50 • Head swivel angle: ±45° • Distance spindle axis to vertical guides: max. 590/90 mm • Spindle speed: 56–1,800 rpm • Rapid traverse: 4,000 mm/min • Spindle drive motor power: 5.5 kW • Operating voltage: 380 V, control voltage 24 V • Total power consumption: 10 kW • Dimensions (L×W×H): 2,080 × 1,700 × 2,260 mm • Total weight incl. hydraulic unit: 4.5 t ⸻ Equipment & Features • Vertical, swivelling milling spindle on a transversely adjustable ram • Hydromechanical tool clamping system • Separate feed drives with DC motors and permanent magnets • Power transmission via toothed belt to preloaded ball screws • Automatic lubrication system for spindle drive and guideways • Hydraulic counterweight for the knee • Manual adjustment via electronic handwheel • Heidenhain control at the swivelling control panel, control cabinet mounted on the machine base • Documentation and operating manual included • Additional images and videos available upon request ⸻ The machine is immediately ready for operation. • Inspection possible at any time • Europe-wide transport available ⸻ Contact Maschinenhandel Nord Gerstenstraße 2 17034 Neubrandenburg 📞 All prices net plus VAT. Subject to modifications and errors. Lsdpfx Aexk Tzgjansak

Condition: used, Year of construction: 2011, functionality: fully functional, machine/vehicle number: 3261, travel distance X-axis: 2,000 mm, travel distance Y-axis: 1,300 mm, travel distance Z-axis: 1,300 mm, rotary table diameter: 1,600 mm, Equipment: rotational speed infinitely variable, Used Milling/Turning Center SHW UniSpeed 5T Laodsw Eb Itspfx Aanok MC-No. 3261 – Year of manufacture: 2011 Travel paths: X = 2,000 mm | Y = 1,300 mm | Z = 1,300 mm Design: Self-rigid machine frame without elaborate foundations. Precision compact roller guides on all axes. Machine column in portal construction, spindle head and saddle made from GGG 60 cast iron with hydraulic weight compensation. Drive & Feed: Digital AC individual drives, stepless 2–30,000 mm/min, acceleration 2 m/s². Direct measuring system for high accuracy. Universal Milling Head (orthogonal): - GGG 60 cast iron, automatic 360°/180° swivel, 64,800 CNC-controlled positions - SK 50, tool pull-in force 20 kN - Power: 26 kW (100% duty cycle) / 36 kW (40% duty cycle), 22–6,000 rpm - Hydromechanical quick tool clamping CNC Rotary Table: - Ø 1,000 mm, planarity 0.015 mm - Turning: up to 250 rpm | Torque: 2,700 Nm - Table load: Milling 6,000 kg, Turning 3,000 kg - Max. swing diameter: 1,800 mm Balancing System: Integrated system for vibration monitoring & correction (DIN ISO 1940 G 6.3 to >G 3). Operation via Siemens 840D. Tool Changer: - Chain magazine for 90 tools - SK 50, max. Ø 125/250 mm, length 400 mm, weight 25 kg - Horizontal tool change, fixed-location coding, air-blow spindle protection Control: Siemens 840D, mounted swiveling on the machine. Electrics: Total connected load approx. 80 kVA. Control voltage 24 V, protection class IP 54, EN 60204. Control cabinet with integrated cabinet cooler (two-chamber system, airtight, with dehumidification). Cooling & Lubrication: - ICS & shower ring (switchable), 500 l tank, max. 40 bar - Minimum quantity lubrication (MQL, Lubrix 850) via spindle - Rinse gun, frame flushing, air/coolant changeover - Lubrication: central for guides, spindle grease-lubricated, milling head oil mist Chip Conveyor: Hinged belt, X-axis 2,000 mm, width 350 mm, discharge height 1,250 mm Additional Systems: - Single-channel collision monitoring - Protective air on glass scales - Wireless 3D probe - Extended milling head swivel range -90° to +110° - VisioPort for clear view - Rotary union in rotary table for clamping hydraulics incl. clamping monitoring - Zero-point clamping system with control panel buttons - Safety glass (18 mm) - Air cleaning unit ILT Unifil 1 MRV70-4.0 (4,200 m³/h) - External B-MPI handheld device with handwheel, override, emergency stop - Energy connections: compressed air 4–6 bar (G¼) Paintwork: Base color RAL 7004 signal grey, functional units RAL 7016 anthracite grey and RAL 9011 graphite black, silk matte, oil & soda resistant.

Condition: new, Fastech horizontal bandsaw semi-automatic machine BMSY 320 DGH saw band dimensions: 4160x34x1,1 mm band speed: 20 - 100 m/min infinitely variable Cutting capacity 0° rectangular: 450x320 mm, round 320mm Cutting capacity 30°: round 320 mm, square 320 mm, rectangle 410x320 mm Cutting capacity 45°: round 320 mm, square 320 mm, rectangle 330x320 mm Cutting capacity - 30°: round 320 mm, square 320 mm, rectangle 420x320 mm Cutting capacity - 45°: round 320 mm, square 320 mm, rectangle 340x320 mm Cutting capacity - 60° : round 240 mm, square 220 mm, rectangle 230x220 mm working height : 860 mm coolant pump motor: 0.12 kW hydraulic motor: 0.37 kW motor: 2.2 kW length: 2260 mm width: 1160 mm Height: 1700 mm Weight: 1030 kg Double mitre saw infinitely variable belt speed hydraulic vice High performance gearbox Hydromechanical saw band tensioning Ljdpfxjg Ekp Ns Aansak Saw band brush Digital display for mitre angle

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 61036721, clamping force: 6,500 kN, screw diameter: 70 mm, clearance between the columns: 1,110 mm, displacement volume: 1,078 cm³, injection pressure: 1,877 bar, injection weight: 981 g, opening stroke: 3,200 mm, plate height: 1,540 mm, drive type: Hydraulisch, clear span: 3,200 mm, tool weight: 22,00,000 g, Injection Moulding Machines Directly from the Manufacturer! As the manufacturer KraussMaffei, we offer you our certified and flexible stock machines: The hydromechanical two-platen clamping unit of the GXW machine sets new standards in terms of quality and productivity. With the sophisticated GuideX sliding shoe, forces are ideally absorbed and the service life of the moulds is extended. The innovative GearX locking system engages instantly and reliably. Powerful, user-friendly and value-retaining. TECHNICAL DATA: KM 650 / 2000 / 2000 GXW G06 (Order 38618339) CONTROL SYSTEM - MC 6 with 24'' TFT color screen with multitouch functions CLAMPING UNIT - Clamping force: 6500 kN - Max. mould opening force: 455 kN - Daylight opening (h x v): 1110 x 960 mm - Platen size (h x v): 1540 x 1440 mm - Mould installation height min. - max.: 1550 mm (without centre platen) - Opening stroke: 3200 mm - Max. mould opening distance: 1650 mm - Max. mould weight: 22,000 kg INJECTION UNIT 1 SP2000 - Screw diameter / type: 60 mm / thermoplastics - Effective L/D ratio: 23.3 - Injection pressure: 2420 bar - Shot volume: 792 cm³ - Shot weight at max. stroke for PS: 720 g - Injection speed: 140 mm/s - Injection throughput: 396 cm³/s - Screw drive speed: 285 rpm Lodpfx Aaew U N Ixeneak - Plasticizing throughput: 72.2 g/s - Nozzle contact force: 82 kN INJECTION UNIT 2 SP2000 - Screw diameter / type: 70 mm / thermoplastics - Effective L/D ratio: 20 - Injection pressure: 1877 bar - Shot volume: 1078 cm³ - Shot weight at max. stroke for PS: 981 g - Injection speed: 140 mm/s - Injection throughput: 539 cm³/s - Screw drive speed: 285 rpm - Plasticizing throughput: 98.3 g/s - Nozzle contact force: 82 kN ELECTRICAL PARAMETERS - Connected load: 341 kW - Power supply: 400 V / 50 Hz, 3 phases with neutral conductor WEIGHT & DIMENSIONS - Net weight: 43.5 t - L x W x H: 11.89 x 3.22 x 2.77 m ADDITIONAL EQUIPMENT - Wear-resistant plasticizing unit - BluePower full insulation for plasticizing cylinder - Open nozzle - BluePower ServoDrive - Pneumatic valve: 1-fold (BWAP), 1-fold (FWAP) - Pneumatic cascade valves: 6-fold (BWAP), 6-fold (FWAP) - Hydraulic core pull: 2-fold (BWAP), 2-fold (FWAP) - Mould heating: 96 zones (3.5 kW each) - Euromap interface for handling: E18 - Euromap central computer interfaces: E67, E77, E78, E63, E82.1 - Adaptive Process Control (APC+) - Graphic analysis package - Sliding table with turning unit, servo-driven - Vertical centre platen - Parallel clamping & opening during injection process with bar parallelism control between FWAP and centre platen or BWAP and centre platen - ColorForm interface signal interface for connecting an RPM unit - Electrical interface for HRS-Flexflow system - Electrical interface and hydraulic valves for "1-K dummy operation" - Interface for connecting a CoMo-Kistler Injection Basic System with good/bad part separation The machine is located at our plant in Parsdorf and is available at short notice. Further additional options can be offered on request. We look forward to your enquiry.

Condition: used, maximum load weight: 1,75,620 kg, overall weight: 2,19,000 kg, axle configuration: > 3 axles, first registration: 01/2002, Equipment: ABS, STHP 8 (3 + 5) 8-piece hydraulic BWP pendulum axle units with radio remote control. Total weight technically possible: 219,000 kg Payload technically possible: 175,620 kg Hydraulically suspended and 8-axle steerable Goldhofer low-bed low-loader type STHP 8 (3+5) consisting of 4 heavy-duty modules with a detachable gooseneck and up to 5-meter-long telescopic excavator low-bed with 4 wheel recesses with ABS up to 175,620 kg payload technically possible. Consisting of the following 4 separate heavy-duty module parts: 1st Module: Hydraulic universal gooseneck type STH / ST Year of manufacture 2002 Can be combined with heavy-duty module chassis, with drive-over loading bridges. Empty weight approx. 5,900 kg Permissible fifth-wheel load front 35,000 kg Length approx. 4.10 m Fifth-wheel height approx. 1.30 m King Pin 3.5" bolt Aluminum side boards plug-in Fully hydraulically adjustable 2nd Module: Goldhofer THP/ST3 3-axle heavy-duty chassis module First registration: 14.11.2001 As a single module total weight technically possible: 108,000 kg, axles technically possible load: 36,000 kg at 5 km/h possible. Empty weight: 10,350 kg As a single module technical payload up to 97,650 kg at 5 km/h possible. Hydraulic pendulum axles 8-fold, 24 x fitted with tires: 215/75/R17.5 Axle load: 25 tons at 20 km/h Vehicle width: 3 meters Axle distance: 1.5 meters Max. steering angle: ±60° Hydromechanical 2-circuit all-wheel forced steering integrated into the chassis with a maximum steering angle of the axle units of 60° with integrated hydraulic oil tank Front and rear optimized bolt-lug coupling for longitudinal combinations Single-tire pendulum axle units with a total of 8 wheels per axle line Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure spring suspension Hydraulic steering of all axles BPW axles with drum brakes and ABS and technically possible axle load of 34 tons at 5 km/h 3rd Module: Extendable heavy-duty low-bed module - excavator bridge Year of manufacture 2002 Internal dimensions approx. 7.50 meters long, 3.00 meters wide and 0.40 meters loading height Construction height 350 mm Extendable by approx. 5.00 meters - telescopic 4 wheel recesses with ramp module in the front area Construction height in the wheel recess area approx. 150 mm Load up to 80 tons in the low-bed and 175.6 tons in the complete STHP8 (3+5) module possible. Empty weight 11,900 kg Front and rear hydraulic bolt lug coupling with claw coupling adapter 4th Module: Goldhofer THP/ET5 5-axle heavy-duty chassis module First registration: 04.01.2002 Technically possible total weight: 115,000 kg, axles technically possible load 23,000 kg at 5 km/h possible Empty weight: 14,200 kg Technical payload up to 100,800 kg possible. Single-tire hydraulic pendulum axle units with 4 wheels per axle line fitted 20x with 285/70 R 19.5 Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure spring suspension Laodpjxcdg Djfx Aanjk Hydraulic steering of all axles Radio remote control for steering axles 5. Notes: With the 4 heavy-duty modules, up to 3 different pull combinations are possible! The payloads change with different pull combinations. A current manufacturer's certificate from Goldhofer is available for the special low-bed combination. The low-bed can be tested at our facility. Price NET plus 19% VAT. All details provided without guarantee. Subject to changes, errors and prior sale. Internal vehicle number: 2285 Advertisement als

Condition: new, Year of construction: 2024, Are you looking for a powerful press brake that can meet even the most demanding requirements? Then the Durma AD-S 803000 press brake with 3000 tons of pressure could be the perfect solution for your needs. With an impressive length of 8 meters and a stroke of 750 mm, this machine is capable of processing even large and heavy materials with the highest precision. The installation height of 1000 mm allows flexible and comfortable positioning of the workpiece. The heart of the machine is the DELEM-DA 66T movable control system, which ensures intuitive operation and precise control of the workflow. In addition, the press brake is a special design and can be configured according to customer requirements to meet all individual needs. If you are interested in Durma press brake, we are at your disposal for personal consultation. Other machines are also available and can be visited. Lsdpfei Da Syjx Aaneak Feel free to contact us for more information and let's find a customized solution for your needs together. Control type: DELEM DA-66T Protection oil: suitable for sea transport Front safety system: FPSC (MANUEL) Sheet metal support system: sliding support arm Stroke: 750 MM Backgauge type: X=1500 X, R Overhang:1050 MM Crowning: Hydromechanical Installation height: 1000 MM Power: 400V 50HZ Body type: Welded frame Under tool holder: DURMA Wide

Condition: excellent (used), Year of construction: 2018, operating hours: 1,192 h, functionality: fully functional, rotor diameter: 260 mm, rotor width: 800 mm, power: 30 kW (40.79 HP), filling opening width: 800 mm, filling opening length: 1,450 mm, working width: 800 mm, Technical data wood and plastic shredder: Manufacturer WEIMA Maschinenbau GmbH Type WLK 800 Year of construction 2018 Operating hours 1,192 hours Drive power 30 kW Speed 90 rpm Rated current 70 A Slow-blow fuse 80 A Hydraulic pressure for horizontal slide 160 bar, load-dependent or pulsed control selectable Rotor type profiled V-rotor Rotor diameter 260 mm Rotor length 800 mm Rotor speed 80 - 125 rpm Number of cutting crowns, concave, 2-row, 42 pieces Cutting crown size 40 x 40 mm Grain size 15 - 80 mm Feed opening 800 x 1450 mm Cutting chamber dimensions 720 x 700 mm Hopper capacity 0.8 m³ Machine dimensions 2,590 x 1,745 x 2,180 mm (l x w x h) PLC control Siemens SIMATIC S7-1200 Screen basket with 30 mm hole size, can be folded downwards Shredder transport weight 2.8 tonnes Laodpswrxklofx Aanek Machine equipment: Segmented floor 2-sided Free-cutting hopper Electromechanical drive with WEIMA WAP gearbox Hydromechanical starting clutch V-rotor (2-row) Adjustable counter blade for regulating the cutting gap Reversible counter blade Remote bearing for easy maintenance Condition of the shredder: The shredder was only used sporadically for wood and plastic shredding and is in good, ready-to-use condition. The machine is available at short notice. Scope of delivery: 1 Weimar WLK 800 shredder with control cabinet Comments: The documentation (Manual, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2022, condition: ready for operation (used), A new injection molding machine including robot is available. 1) Krauss Maffei injection molding machine, year of manufacture: 2022, clamping system: hydromechanical clamping system with 2 platens. Plasticizing: 8100, screw diameter: 105mm, nozzle radius: 35mm, nozzle bore: 6mm, clamping force: 1700t, control: MC6. 2) Industrial robot Kuka IR 1200 R3100.2 F/K, max. payload: 120kg, reach: 3100mm, repeatability: +/-0.05mm, control: KR C5. Documentation available. On-site inspection is possible. Laedpfsvpvlcjx Aansk

Condition: new, maximum load weight: 38,400 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the specifications. Full specification available on request. Loading area: * Extendable loading platform with pneumatically operated locking mechanism * Loading area with approx. 30 mm thick wooden planks * 7 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the platform for hooking in tension straps (LC 2,000 daN) Landing legs: * JOST mechanical landing legs with 2-speed gearbox, approx. 24 t lifting capacity (approx. 50 t test load) Tyres: * Tyres: 385/65 R 22.5, manufacturer at our discretion * TPMS tyre pressure monitoring system in accordance with ECE R 141. Data transmission to the truck is via the standardized EBS interface as per ISO 11992. For proper display, the truck must be capable of receiving and showing this data. Axle: * BPW axles and suspension * All axles hydromechanically forced-steered * Disc brakes * Technical axle load: 10,000 kg each (offset 0) * Air suspension with raise/lower valve * Axle tools Brake system: * WABCO brake system in accordance with EU regulations, EBS-E (2S2M) without connection lines to the tractor unit Steel construction: * High-strength fine-grain steel construction * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: Laodew Tpr Iepfx Aansk * Electrical system in accordance with EU regulations * LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash together with indicators * ASPÖCK-UNIBOX at the front connection bar with 24N, 24S, and 15-pin sockets according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Complete steel structure automatically shot-blasted after welding * Second blasting with corundum for optimal coating adhesion * Final painting with two coats of 2-component topcoat, single color, RAL 3002 Carmine Red according to RAL system 841GL * Rims in silver grey * Rear section metallized and painted RAL 9010 (Pure White) * Metallic paint not available * Paint finish tested in salt spray test according to ISO 9227-NSS * Cavity sealing with special wax Accessories: * Remote steering from front and rear via cable remote control with push buttons, with axle tracking monitoring (without installation in the tractor unit) * Electro-hydraulic unit * 4 wheel chocks with holders on the front wall * 2" kingpin * Yellow-red air couplings at the galvanized front connection bar * At gooseneck and rear, left and right, brackets for warning panels, including sockets * 10 pairs of stake pockets for approx. 100 x 50 mm plug-in stakes in the external frame of the loading platform * One galvanized steel front wall (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container pockets in the loading area, for 1 x 20' container, 2 x 20' containers, or 1 x 40' container; an additional locking position is provided in the extension for a 45' container * 4 pairs of transverse stake pocket strips in the loading area for approx. 100 x 50 mm plug-in stakes * Storage for max. 9 pairs of plug-in stakes bolted inside to the front wall * Boarding ladder mounted left and right in the direction of travel * One INOX toolbox, approx. 1,200 x 460 x 550 mm, mounted front left under the loading platform * An additional INOX toolbox, approx. 1,200 x 46...

Year of construction: 2021, condition: new, Fastech horizontal bandsaw semi-automatic BMSY 360 DGH ECO Round cutting range mm: 360 Flat cutting range mm: 510 x 360 Square Cutting range mm: 360 +30 ° Round cutting range mm: 360 +30 ° Flat Cutting range mm: 440 x 360 +30 ° Square Cutting range mm: 360 +45 ° Round Cutting range mm: 360 +45 ° Flat cutting range mm: 390 x 360 +45 ° Square cutting area mm: 360 +60 ° Round cutting range mm: 200 +60 ° Flat cutting range mm: 200 x 360 +60 ° Square cutting range mm: 200 -30 ° Round cutting range mm: 360 -30 ° Flat cutting range mm: 440 x 360 -30 ° Square cutting range mm: 360 -45 ° Round cutting range mm: 360 Laedpjg Ekttefx Aanok -45 ° Flat cutting range mm: 390 x 360 -45 ° Square cutting area mm: 360 -60 ° Round cutting range mm: 260 -60 ° Flat cutting range mm: 260 x 360 -60 ° Square cutting range mm: 260 Engine power main drive kW 3 Hydraulic pump power kW 0,37 Engine power coolant pump kW 0,12 Band speed, infinitely variable: m/min.20 - 100 Saw band dimensions mm: 4800x34x1,1 Working surface height mm: 860 weight kg: 1450 length / depth / height mm: 2650 / 1210 / 1870 Double mitre saw Infinitely variable belt speed hydraulic vice High performance gearbox Hydromechanical saw band tensioning Saw band brush Digital display for mitre angle

Condition: used, maximum load weight: 1,75,620 kg, overall weight: 2,19,000 kg, axle configuration: > 3 axles, first registration: 01/2002, Equipment: ABS, STHP 8 (3 + 5) 8 units of hydraulic BWP pendulum axle assemblies with remote control. Technically permissible gross weight 219,000 kg Technically permissible payload 175,620 kg Hydraulically suspended, 8-axle steered Goldhofer low-bed heavy-duty trailer type STHP 8 (3+5), consisting of 4 heavy-duty modules with a detachable gooseneck and extendable excavator low-bed section up to 5 meters, featuring 4 wheel recesses, ABS, technically permissible payload up to 175,620 kg. Consisting of the following 4 separate heavy-duty module parts: 1st module: Hydraulic universal gooseneck type STH/ST Year of manufacture: 2002 Can be combined with heavy-duty module undercarriages, drivable loading platforms. Unladen weight approx. 5,900 kg Permissible front fifth wheel load: 35,000 kg Length approx. 4.10 m Fifth wheel height approx. 1.30 m King pin 3.5" pin Removable aluminum side walls Fully hydraulically adjustable 2nd module: Goldhofer THP/ST3 3-axle heavy-duty module First registration: 14.11.2001 As a single module, technically permissible total weight: 108,000 kg, technically permissible axle loads: 36,000 kg at 5 km/h possible. Unladen weight: 10,350 kg As a single module, technical payload up to 97,650 kg at 5 km/h possible. 8 hydraulic pendulum axles, 24 wheels, tire size: 215/75/R17.5 Axle load: 25 t at 20 km/h Vehicle width: 3 meters Axle spacing: 1.5 meters Max. steering angle: ±60° Integrated into chassis: hydromechanical dual-circuit all-wheel forced steering with a maximum aggregate steering angle of 60°, integrated hydraulic oil tank Optimized bolt-lug coupling at front and rear for longitudinal combinations Single-tired pendulum axle assemblies with a total of 8 wheels per axle line Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure suspension Hydraulic steering for all axles BPW axles with drum brake and ABS, technically permissible axle load of 34 t at 5 km/h 3rd module: Extendable low-bed heavy-duty module - Excavator bridge Year of manufacture: 2002 Internal dimensions approx. 7.50 meters long, 3.00 meters wide, loading height 0.40 meters Construction height 350 mm Extendable by approx. 5.00 meters - telescopic 4 wheel recesses with drive-on module at the front Construction height in wheel recess area approx. 150 mm Load capacity up to 80 t in low-bed and 175.6 t in overall STHP8 (3+5) module possible. Unladen weight 11,900 kg Front and rear hydraulic bolt-lug coupling with claw coupling adapter 4th module: Goldhofer THP/ET5 5-axle heavy-duty module First registration: 04.01.2002 Technically permissible total weight: 115,000 kg, technically permissible axle loads 23,000 kg at 5 km/h possible Unladen weight: 14,200 kg Technical payload up to 100,800 kg possible. Single-tired hydraulic pendulum axle assemblies with 4 wheels per axle line, 20 wheels (tire size 285/70 R 19.5) Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure suspension Hydraulic steering for all axles Remote control for steering axles 5. Notes: With the 4 heavy-duty modules, up to 3 different tractor combinations are possible! Payloads change depending on the configuration. For the special low-bed combination, a current manufacturer's certificate from Goldhofer is available. The low-bed trailer can be tested at our facility. Price NET excluding 19% VAT. All information without guarantee. Subject to errors and prior sale. Internal vehicle number: 2285 Lodpfxjxcdgqs Aaneak

Condition: new, Fastech Horizontal Double Miter Band Saw Semi Automatic BMSY 440 DGH Round cutting range: mm 440 Flat Cutting range: mm 610 x 440 Square Cutting range: mm 440 +30 ° Round Cutting range: mm 400 +30 ° Flat Cutting range: mm 500 x 440 +30 ° Square Cutting range: mm 440 Lsdpfjhpil Eex Aaneak +45 ° Round Cutting range: mm 440 +45 ° Flat cutting range: mm 410 x 440 +45 ° Square cutting range: mm 410 +60 ° Round Cutting range: mm 320 +60 ° Flat cutting range: mm 250 x 440 +60 ° Square cutting range: mm 250 -30 ° Round cutting range: mm 440 -30 ° Flat cutting range: mm 500 x 440 -30 ° Square cutting range: mm 410 -45 ° Round Cutting range: mm 410 -45 ° Flat cutting range: mm 410 x 440 -45 ° Square cutting range: mm 410 -60 ° Round cutting range: mm 320 -60 ° Flat cutting range: mm 285 x 440 -60 ° Square cutting range: mm 285 Engine power main drive: kW 3 Hydraulic pump power: kW 0,55 Engine power coolant pump: kW 0,12 Belt speed: stepless m/min. 20 - 100 Saw band dimensions mm 5200 x34 x 1,1 working surface height: mm 860 weight: kg 1540 length / depth / height: mm 2800 / 1210 / 1870 Double miter saw Infinitely variable band speed, hydraulic vice sensitive cutting pressure regulation High performance gearbox Hydromechanical saw band tensioning Saw band brush Digital display for miter angle

Condition: used, maximum load weight: 1,75,620 kg, overall weight: 2,19,000 kg, axle configuration: > 3 axles, first registration: 01/2002, Equipment: ABS, STHP 8 (3 + 5) 8 units of hydraulic BWP pendulum axle assemblies with remote control. Technically permissible gross weight 219,000 kg Technically permissible payload 175,620 kg Hydraulically suspended, 8-axle steered Goldhofer low-bed heavy-duty trailer type STHP 8 (3+5), consisting of 4 heavy-duty modules with a detachable gooseneck and extendable excavator low-bed section up to 5 meters, featuring 4 wheel recesses, ABS, technically permissible payload up to 175,620 kg. Consisting of the following 4 separate heavy-duty module parts: 1st module: Hydraulic universal gooseneck type STH/ST Year of manufacture: 2002 Can be combined with heavy-duty module undercarriages, drivable loading platforms. Unladen weight approx. 5,900 kg Permissible front fifth wheel load: 35,000 kg Length approx. 4.10 m Fifth wheel height approx. 1.30 m King pin 3.5" pin Removable aluminum side walls Fully hydraulically adjustable 2nd module: Goldhofer THP/ST3 3-axle heavy-duty module First registration: 14.11.2001 As a single module, technically permissible total weight: 108,000 kg, technically permissible axle loads: 36,000 kg at 5 km/h possible. Unladen weight: 10,350 kg As a single module, technical payload up to 97,650 kg at 5 km/h possible. 8 hydraulic pendulum axles, 24 wheels, tire size: 215/75/R17.5 Axle load: 25 t at 20 km/h Vehicle width: 3 meters Axle spacing: 1.5 meters Max. steering angle: ±60° Integrated into chassis: hydromechanical dual-circuit all-wheel forced steering with a maximum aggregate steering angle of 60°, integrated hydraulic oil tank Optimized bolt-lug coupling at front and rear for longitudinal combinations Single-tired pendulum axle assemblies with a total of 8 wheels per axle line Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure suspension Hydraulic steering for all axles BPW axles with drum brake and ABS, technically permissible axle load of 34 t at 5 km/h 3rd module: Extendable low-bed heavy-duty module - Excavator bridge Year of manufacture: 2002 Internal dimensions approx. 7.50 meters long, 3.00 meters wide, loading height 0.40 meters Construction height 350 mm Extendable by approx. 5.00 meters - telescopic 4 wheel recesses with drive-on module at the front Construction height in wheel recess area approx. 150 mm Load capacity up to 80 t in low-bed and 175.6 t in overall STHP8 (3+5) module possible. Unladen weight 11,900 kg Front and rear hydraulic bolt-lug coupling with claw coupling adapter 4th module: Goldhofer THP/ET5 5-axle heavy-duty module First registration: 04.01.2002 Technically permissible total weight: 115,000 kg, technically permissible axle loads 23,000 kg at 5 km/h possible Unladen weight: 14,200 kg Technical payload up to 100,800 kg possible. Single-tired hydraulic pendulum axle assemblies with 4 wheels per axle line, 20 wheels (tire size 285/70 R 19.5) Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure suspension Hydraulic steering for all axles Remote control for steering axles 5. Notes: With the 4 heavy-duty modules, up to 3 different tractor combinations are possible! Payloads change depending on the configuration. For the special low-bed combination, a current manufacturer's certificate from Goldhofer is available. The low-bed trailer can be tested at our facility. Price NET excluding 19% VAT. All information without guarantee. Subject to errors and prior sale. Internal vehicle number: 2285 Lajdpexcdf Hefx Aanek

Condition: used, maximum load weight: 1,75,620 kg, overall weight: 2,19,000 kg, axle configuration: > 3 axles, first registration: 01/2002, Equipment: ABS, STHP 8 (3 + 5) 8-piece hydraulic BWP pendulum axle units with radio remote control. Total weight technically possible: 219,000 kg Payload technically possible: 175,620 kg Hydraulically suspended and 8-axle steerable Goldhofer low-bed low-loader type STHP 8 (3+5) consisting of 4 heavy-duty modules with a detachable gooseneck and up to 5-meter-long telescopic excavator low-bed with 4 wheel recesses with ABS up to 175,620 kg payload technically possible. Consisting of the following 4 separate heavy-duty module parts: 1st Module: Hydraulic universal gooseneck type STH / ST Year of manufacture 2002 Can be combined with heavy-duty module chassis, with drive-over loading bridges. Empty weight approx. 5,900 kg Ledjxcdfaspfx Aansak Permissible fifth-wheel load front 35,000 kg Length approx. 4.10 m Fifth-wheel height approx. 1.30 m King Pin 3.5" bolt Aluminum side boards plug-in Fully hydraulically adjustable 2nd Module: Goldhofer THP/ST3 3-axle heavy-duty chassis module First registration: 14.11.2001 As a single module total weight technically possible: 108,000 kg, axles technically possible load: 36,000 kg at 5 km/h possible. Empty weight: 10,350 kg As a single module technical payload up to 97,650 kg at 5 km/h possible. Hydraulic pendulum axles 8-fold, 24 x fitted with tires: 215/75/R17.5 Axle load: 25 tons at 20 km/h Vehicle width: 3 meters Axle distance: 1.5 meters Max. steering angle: ±60° Hydromechanical 2-circuit all-wheel forced steering integrated into the chassis with a maximum steering angle of the axle units of 60° with integrated hydraulic oil tank Front and rear optimized bolt-lug coupling for longitudinal combinations Single-tire pendulum axle units with a total of 8 wheels per axle line Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure spring suspension Hydraulic steering of all axles BPW axles with drum brakes and ABS and technically possible axle load of 34 tons at 5 km/h 3rd Module: Extendable heavy-duty low-bed module - excavator bridge Year of manufacture 2002 Internal dimensions approx. 7.50 meters long, 3.00 meters wide and 0.40 meters loading height Construction height 350 mm Extendable by approx. 5.00 meters - telescopic 4 wheel recesses with ramp module in the front area Construction height in the wheel recess area approx. 150 mm Load up to 80 tons in the low-bed and 175.6 tons in the complete STHP8 (3+5) module possible. Empty weight 11,900 kg Front and rear hydraulic bolt lug coupling with claw coupling adapter 4th Module: Goldhofer THP/ET5 5-axle heavy-duty chassis module First registration: 04.01.2002 Technically possible total weight: 115,000 kg, axles technically possible load 23,000 kg at 5 km/h possible Empty weight: 14,200 kg Technical payload up to 100,800 kg possible. Single-tire hydraulic pendulum axle units with 4 wheels per axle line fitted 20x with 285/70 R 19.5 Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure spring suspension Hydraulic steering of all axles Radio remote control for steering axles 5. Notes: With the 4 heavy-duty modules, up to 3 different pull combinations are possible! The payloads change with different pull combinations. A current manufacturer's certificate from Goldhofer is available for the special low-bed combination. The low-bed can be tested at our facility. Price NET plus 19% VAT. All details provided without guarantee. Subject to changes, errors and prior sale. Internal vehicle number: 2285 Advertisement als

Condition: used, maximum load weight: 1,75,620 kg, overall weight: 2,19,000 kg, axle configuration: > 3 axles, first registration: 01/2002, Equipment: ABS, STHP 8 (3 + 5) 8-piece hydraulic BWP pendulum axle units with radio remote control. Total weight technically possible: 219,000 kg Payload technically possible: 175,620 kg Hydraulically suspended and 8-axle steerable Goldhofer low-bed low-loader type STHP 8 (3+5) consisting of 4 heavy-duty modules with a detachable gooseneck and up to 5-meter-long telescopic excavator low-bed with 4 wheel recesses with ABS up to 175,620 kg payload technically possible. Consisting of the following 4 separate heavy-duty module parts: 1st Module: Hydraulic universal gooseneck type STH / ST Year of manufacture 2002 Can be combined with heavy-duty module chassis, with drive-over loading bridges. Empty weight approx. 5,900 kg Permissible fifth-wheel load front 35,000 kg Length approx. 4.10 m Fifth-wheel height approx. 1.30 m King Pin 3.5" bolt Aluminum side boards plug-in Fully hydraulically adjustable 2nd Module: Goldhofer THP/ST3 3-axle heavy-duty chassis module First registration: 14.11.2001 As a single module total weight technically possible: 108,000 kg, axles technically possible load: 36,000 kg at 5 km/h possible. Empty weight: 10,350 kg As a single module technical payload up to 97,650 kg at 5 km/h possible. Hydraulic pendulum axles 8-fold, 24 x fitted with tires: 215/75/R17.5 Axle load: 25 tons at 20 km/h Vehicle width: 3 meters Axle distance: 1.5 meters Max. steering angle: ±60° Hydromechanical 2-circuit all-wheel forced steering integrated into the chassis with a maximum steering angle of the axle units of 60° with integrated hydraulic oil tank Front and rear optimized bolt-lug coupling for longitudinal combinations Single-tire pendulum axle units with a total of 8 wheels per axle line Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure spring suspension Hydraulic steering of all axles BPW axles with drum brakes and ABS and technically possible axle load of 34 tons at 5 km/h 3rd Module: Extendable heavy-duty low-bed module - excavator bridge Year of manufacture 2002 Internal dimensions approx. 7.50 meters long, 3.00 meters wide and 0.40 meters loading height Construction height 350 mm Extendable by approx. 5.00 meters - telescopic 4 wheel recesses with ramp module in the front area Construction height in the wheel recess area approx. 150 mm Load up to 80 tons in the low-bed and 175.6 tons in the complete STHP8 (3+5) module possible. Empty weight 11,900 kg Front and rear hydraulic bolt lug coupling with claw coupling adapter 4th Module: Goldhofer THP/ET5 5-axle heavy-duty chassis module First registration: 04.01.2002 Technically possible total weight: 115,000 kg, axles technically possible load 23,000 kg at 5 km/h possible Empty weight: 14,200 kg Technical payload up to 100,800 kg possible. Laedpfx Aajxcdf Tjnek Single-tire hydraulic pendulum axle units with 4 wheels per axle line fitted 20x with 285/70 R 19.5 Hydraulic axle compensation +/- 300 mm, hydropneumatic gas pressure spring suspension Hydraulic steering of all axles Radio remote control for steering axles 5. Notes: With the 4 heavy-duty modules, up to 3 different pull combinations are possible! The payloads change with different pull combinations. A current manufacturer's certificate from Goldhofer is available for the special low-bed combination. The low-bed can be tested at our facility. Price NET plus 19% VAT. All details provided without guarantee. Subject to changes, errors and prior sale. Internal vehicle number: 2285 Advertisement als