Used Jackle Power Plasma for sale (36,881)

Condition: excellent (used), Year of construction: 2017, working range: 4,000 mm, overall weight: 6,500 kg, total width: 2,400 mm, total height: 2,600 mm, total length: 6,000 mm, Working area X Axis:4000mm Working area Y Axis:2000mm Redpfx Agsy T Hyweujcb Working area Z axis:400mm Power resonator: 300kW / Amp Feed rate X-Axis: 10000mm/min. Feed rate Y-Axis: 10000mm/min. Feed rate Z-Axis: 10000mm/min. Dust collector: Kemper Length: 6000mm Width: 2400mm Height: 2600mm Weight: 6500kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Hydr. flat form scissor lift table FLEXLIFT FLUNDER type 1500 / 100 (without hydraulic unit) Year of manufacture 1991 Nominal lifting capacity 1500 kg Lifting capacity (practically tested) 1000 kg (at approx. 350 bar) platform size 2100 x 1400 mm stroke max. 930 mm Overall height - bottom 100 mm (with mounting frame) Overall height - top 1030 mm Hydr. operating pressure 350 bar = lifting force 1000 kg Motor power of hydraulics 1,5 kW Rcodpsl Nbqcofx Agueb mains connection 400 Volt, 50 Hz - mechanical-hydraulic safety limit switches stop the lowering process when the safety bar is actuated - without hydraulic power unit - without electric control length of installation frame 2270 mm width of mounting frame 1580 mm height of mounting frame = height at bottom 100 mm dead weight of lifting table 500 kg good condition

Condition: used, Plasma cutting unit, plasma cutting machine MESSER GRIESHEIM Type Plasmastar HA 95 Serial No. 4040323 Year of manufacture: 1990 Power: 95 Amp. - 60% duty cycle 45 Amp. - 70% duty cycle Adjustment range: 2 steps Cutting capacity: 25 mm (clean cut) Severance cut up to 45 mm Hand torch: PHC 95/140 Power supply: 380 Volt, 50 Hz, 32 Amp. plug - Water-cooled - New hand torch BINZEL ABICOR, Type Abiplas Cut 200 W - 6 meter hose package length - Operating manual Rjdjyah R Nopfx Agujcb Space requirements (L x W x H): 900 x 480 x 850 mm Weight: 160 kg Very good condition

Condition: used, Pneumohydraulic cylinder TOX Pressotechnik Hydro-pneumatic press, power pack Type: S 04.00.050.12 D No.: 208696.460 Year of manufacture approx. 2000 Pressure capacity: 4.0 tons at 10 bar Pressure capacity: 3.0 tons at 8 bar Pressure capacity: 2.6 tons at 7 bar Pressure capacity: 2.4 tons at 6 bar Pressure capacity: 2.0 ton. at 5 bar Pressure capacity: 1.6 ton. at 4 bar Pressure capacity: 1.2 tons at 3 bar Total stroke: 50 mm Rodpfju D Tz Ujx Agujcb Power stroke: 12 mm Piston rod: Ø 30 mm Thread for piston rod: M22 x 2 mm Compressed air requirement: 3 to 10 bar - Electronic oil pressure switch with TOX digital display for force measurement, type 167282 - Height only power pack with piston rod = 610 mm - Height of power pack hydropneumatic cylinder only = 560 mm - Additional base plate 160 x 160 x 20 mm - Plunger plate: Ø 68 mm Space requirement L x W x H: 160 x 160 x 660 mm Weight: 21 kg Very good condition 3 pieces available, price per piece

Condition: used, Hydraulic unit, whisper unit BOSCH REXROTH Hydraulic unit Type UPE 5- /1.50V7/06-10A-H-1-S090+04100891 Factory no. R904100893 / 480933 10 Year of manufacture approx. 2010 Rcedpfsv Ev Dqox Agujb Pressure output: 55 bar Delivery rate: 13 L/min. Tank capacity: approx. 20 liters Engine power: 1.5 kW Speed: 1440 rpm. Mains connection: 400 volts, 50 Hz - Unit was used for an operating pressure of approx. 80 bar - 1 hydraulic pump, vane pump BOSCH REXROTH, type PV7-11/06-10RA0MA0-10, pressure max. 100 bar - 1 air-oil cooler, fan cooling by electric motor from the hydraulic pump - Hydraulic block BOSCH REXROTH, type UPES-11/ ABZSS6-C-140E-S30-S13 - 2 hydraulic pressure accumulators - 1 replaceable filter cartridge - 1 pressure sensor IFM, type TR7 430 - 1 oil sight glass - Hydraulic connections 2x 18L - Sold without oil content Space requirement L x W x H: 700 x 450 x 850 mm Weight: 105 kg very good condition

Year of construction: 2008, condition: good (used), Railcar, platform wagon, heavy-duty transport wagon, transport wagon, heavy-duty wagon, electric heavy-duty rail wagon, rail wagon, trailer -Manufacturer: Mechanic Maschinenbau Hahn, electric heavy-duty railcar with lifting cylinder -Type: Railcar MTA, load capacity 20000 kg -Roller spacing (track gauge): 2150 mm -Cylinder spacing: 2245 mm -Lift height: 110 mm Rodpfx Agjlbdlzeujcb -Drive units: 2x Demag geared motors type ZBF80A 4 B020 gearbox type ADE40TD -Individual components: see photos -Overall dimensions: 2860/2440/H610 mm -Empty weight: 2200 kg

Condition: new, FORD Emergency Power System Rodpfsy U Dr Tox Agujcb

Year of construction: 2003, operating hours: 200 h, condition: ready for operation (used), Equipment: 4 in one shovel, Bluetooth, Capable to welt up to 8mm. Roller table including the deal Rodpfsy Tia Hsx Aguscb Feel free to offer. Machine will be dismantled after 6th of June 2026

Condition: used, OKUMA POWER SUPPLY GLP 5000T E0451-521-037 Rcedpfjy S Dr Ujx Agujb . 2663

Condition: used, length ~ 450 mm width ~ 650 mm Rodpfxox R Ttlj Aguocb height ~ 1.100 mm Battery-powered hand strapping tool BW-03 with 2 x battery, charger and Cyklop dispenser and 2.5 rolls of strapping.

Condition: used, Pressure: 100 bar Rcjdpfswdun Dox Agujb Capacity: 2 L Motor: 0.75 kW

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, operating hours: 4,500 h, input voltage: 400 V, travel distance X-axis: 700 mm, number of slots in tool magazine: 21, controller manufacturer: fanuc, controller model: 31i model B5, rapid traverse Z-axis: 60 m/min, rapid traverse X-axis: 60 m/min, rapid traverse Y-axis: 60 m/min, spindle nose: BT 30 big plus, spindle speed (max.): 10,000 rpm, operating hours of spindle: 4,500 h, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, FULL OPTIONAL TAPPING CENTER high torque/power version, complete with: spindle cone with BIG PLUS attachment FANUC DDR-T: continuous fourth axis (direct drive motor) with braked counter support and plate Rodpfxsuby Sxj Agujcb rotary joint for hydraulic feed to center table (for automatic workpiece clamping/unclamping) hydraulic power unit for workpiece clamping high-pressure refrigeration through the spindle chip conveyor evacuation automatic side poet robot interface tool setter RENISHAW TS-27 perfect machine with only 4,500 spindle hours!

Condition: excellent (used), I sell plasma cutter hypertherm powermax 800 d very good condition. /////Price listed for 1 pc ///// Plasma cutter Hypertherm Powermax 800 Plasma cutter description Rjdpfxsulc Ixo Agujcb The Powermax800 plasma cutting system uses an inverter power supply to provide a smooth DC output voltage for superior cutting and gouging of mild steel, stainless steel, aluminum and other metals. The Powermax800's power supply provides a constant output current that varies from 20 to 50 amps, providing optimal performance for all metal thicknesses up to 1/2 inch (12 mm). At 50 amps, the Powermax800 can cut metals up to 3/4 inch (20 mm) thick and cut metals up to 1 inch (25 mm) thick.

Year of construction: 2024, condition: new, Everything is configurable on demand, very short production & delivery time. We will be happy to provide you with further information on request. Technical data on request. Standard equipment: Rcedefirx Nepfx Aguob welded steel construction DURMA CNC control unit (AURORA) Remote control diagnostics (Ethernet) Lantek Software W / Automatic Nesting Position determination of the sheet metal to be cut by laser DURMA Burner height control Double-sided drive system (rack and pinion) AC servo motors for X and Y axis movement CNC control outputs/inputs for the filter unit Consumables Starter-Kit Plasma torch * Ignition console * Burner height regulation with Ball screws on double Linear bearings * Special equipment: Hypertherm Max Pro 200 + hose package + nozzles + Durma THC + torch Hypertherm HPR 130 XD + hose package+ nozzles + Durma THC + ignition console + burner Hypertherm HPR 260 XD + hose package+ nozzles + Durma THC + ignition console + burner Hypertherm + Hypertherm HPR 400 XD + hose package + nozzles + Durma THC + ignition console + burner CE Standard Safety wire Automatic gas console for Hypertherm, Manual gas console for Hypertherm, Autogenous cutting torches Plasma torch protection system manual plasma angle cutting head, CNC angle cutting head (+/- 45). Single drilling head Multiple drilling head Filter for 130A, 260A or 400A Pipe cutting unit Ø50 mm - Ø400 mm Additional support for the pipe cutting unit Warning lamp for error and program end With over 60 years of experience

Condition: new, Year of construction: 2021, machine/vehicle number: XPR300-005397, type of input current: three-phase, overall weight: 680 kg, input voltage: 360 V, cutting current: 300 A, ambient temperature (max.): 40 °C, We offer this new Hypertherm XPR300 plasma cutting source, year of manufacture 2021. Only the plasma source is for sale. New, unused. 2 plasma sources available. Forklift on site. Manufacturer: Hypertherm Model: XPR300 Year of manufacture: 2021 Condition: new Category ID: 1448 Type ID: 2170 Type: plasma cutting machine Rcedpfx Agsy Dqrfoueb If you have any questions or need further information, please send us a message or call us.

Condition: used, Plasma Cutting & Grooving with Hand Torch, from 3 to 45 mm Simple and cost-effective technology for any cutting application The PA-S45 W plasma cutting system is suitable for manual and mechanized cutting in the material thickness range of 3 to 45 mm. By using different plasma gases and gas mixtures, electrically conductive materials can be cut and grooved cleanly. As a mobile system, it can be used in workshops, training centers, and on construction sites. Advantages: Optional use of hand or machine torch Suitable for 2D & 3D guidance systems Rjdpfx Agey U Urkouecb Robust and simple design Mobile systems for flexible use Reliability even under difficult production conditions Cutting current can be pre-selected in three stages Effective cooling of the plasma torch and its wear parts Quick changeover from cutting to plasma grooving and vice versa Angled torch heads and special shank designs for optimized cutting of 3D parts Wide range of applications thanks to optional equipment Liquid-cooled plasma torches The proven design of the torch components, cathode, and nozzle, is a prerequisite for the quality of the cut surfaces. The liquid cooling of the plasma fine-jet torches guarantees their long service life. Plasma cutting with the systems in the PA-S series is therefore efficient and increases the user's productivity. When cutting construction steel with the PA-S45 W, a swirl gas torch often allows for more frequent piercing. Plasma Grooving Both machine and hand torches can be quickly converted for plasma grooving. This requires changing the nozzles and attaching the ceramic cap (if necessary, with a protector). By using different plasma gases and gas mixtures, all electrically conductive materials such as construction steel, stainless steel, aluminum, and brass can be processed. Plasma grooving is ideally suited for removing welding defects, cracks, porosity, and inclusions, as well as for preparing for counter-welding. Advantages: No carbonization of the material No post-grinding required Low heat input Good observation of the process Reduction of noise levels and smoke generation

Condition: used, functionality: fully functional, machine/vehicle number: 11.031.802, Plasma Cutting & Grooving with Hand Torch, from 3 to 45 mm Rodpfx Aoy U Uqtegujcb Simple and cost-effective technology for any cutting application The PA-S45 W plasma cutting system is suitable for manual and mechanized cutting in the material thickness range of 3 to 45 mm. By using different plasma gases and gas mixtures, electrically conductive materials can be cut and grooved cleanly. As a mobile system, it can be used in workshops, training centers, and on construction sites. Advantages: Optional use of hand or machine torch Suitable for 2D & 3D guidance systems Robust and simple design Mobile systems for flexible use Reliability even under difficult production conditions Cutting current can be pre-selected in three stages Effective cooling of the plasma torch and its wear parts Quick changeover from cutting to plasma grooving and vice versa Angled torch heads and special shank designs for optimized cutting of 3D parts Wide range of applications thanks to optional equipment Liquid-cooled plasma torches The proven design of the torch components, cathode, and nozzle, is a prerequisite for the quality of the cut surfaces. The liquid cooling of the plasma fine-jet torches guarantees their long service life. Plasma cutting with the systems in the PA-S series is therefore efficient and increases the user's productivity. When cutting construction steel with the PA-S45 W, a swirl gas torch often allows for more frequent piercing. Plasma Grooving Both machine and hand torches can be quickly converted for plasma grooving. This requires changing the nozzles and attaching the ceramic cap (if necessary, with a protector). By using different plasma gases and gas mixtures, all electrically conductive materials such as construction steel, stainless steel, aluminum, and brass can be processed. Plasma grooving is ideally suited for removing welding defects, cracks, porosity, and inclusions, as well as for preparing for counter-welding. Advantages: No carbonization of the material No post-grinding required Low heat input Good observation of the process Reduction of noise levels and smoke generation

Condition: used, OKUMA POWER SUPPLY 5000T E0451-521-038 . 03487 Rcjdjy Suyvepfx Agusb

Year of construction: 2020, condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. Rodpfxsfz Ndyj Aguocb We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Oil, gas or electric furnace? You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? We will try to answer your questions. Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution.

Year of construction: 2020, condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. Rsdjflrc Sepfx Agujcb ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Oil, gas or electric furnace? You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? We will try to answer your questions. Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution.

Year of construction: 2020, condition: new, ROMER® deals with the production of single technological equipment for powder coating plants as well as complete fully automatic turnkey coating plants. ROMER® provides heating solutions for the aero and automotive industries for the largest corporations in the world. We provide warranty and post-warranty service for devices sold by us with a full range of spare parts. the trawl applied to a poorly prepared surface will fall off or corrode after a short period of time. Rjdsfz A H Depfx Aguscb Ensuring the best coating is essentially good degreasing - which is the basis of any painting. The coating of a poorly degreased detail will fall off after a very short time. After degreasing, the next step is to tear down the outer coating of the detail, which improves paint adhesion, e.g. when bending sheet metal, and protection, e.g. with a phosphate layer, which in turn will prolong corrosion resistance. There are many solutions that solve the above issues. What is the most important thing in a powder coating shop? You probably don't have experience with the applicator. Nothing more wrong, even the best applicator will not help you if your oven has bad temperature distributions, in the place where the element is overheated, the paint will discolor and where not heated, the paint will fall off. First of all, the stove is the most important. Oil, gas or electric furnace? You don't know how to power your stove? how is cheaper what does this involve? What are the operating costs? We will try to answer your questions. Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution.

Condition: used, Three-phase power meter: current, voltage, and power measurement; long-term monitoring; energy measurement 3-phase power measurement device, ammeter, voltmeter, digital measuring instrument, active power, apparent power, reactive power BEHA Type UNITEST Power Analyzer 93555 For measuring voltage, current, active power, apparent power, reactive power, power factor, phase angle, frequency measurement, phase sequence detection, energy measurement, and harmonics measurement. Display: LC multifunction display with backlight Refresh rate: approx. 2 sec. Data logger: 512 KB non-volatile memory (max. 21,000 readings, max. 10 data sets) Sampling rate: 5 s, 30 s, 1 min, 2 min. (adjustable) Rcjdpfex A Imzjx Agujb Data transmission: via optically isolated RS232 interface Manual memory: max. 99 measurements Overvoltage category: CAT III 600 V Power supply: 8 x 1.5V AA batteries or mains adapter 230VAC / 12VDC (batteries not included) Voltage measurement: 3 input channels with common reference point "N" Measuring range: 0 - 600 V RMS Display range: 0 - 999.9 V RMS Resolution: 0.1 V Mains frequency: 50 Hz Current measurement: Measuring range Input I1, I2, I3: 3 - 999.9 A Input I4: 3 - 250 A Display range: 0 - 999.9 A Resolution: 0.1 A Clamp opening: 40 mm Active power: Selectable display of the active power of an individual input or the total value Display range: 0 - 999.9 kW Resolution: 0.1 kW Apparent power: Calculated from the RMS values of voltage and current Display range: 0 - 999.9 kVA Resolution: 0.1 kVA Frequency measurement: Range: 45...80 Hz Resolution: 0.1 Hz Accessories: - Carrying case - Operating manual - 4 measuring clamps - 4 test leads with crocodile clips - RS232 adapter cable - Mains adapter 230VAC / 12VDC Overall dimensions (W x H x D): 370 x 270 x 170 mm Total weight: 3 kg Device tested, fully functional. Note: The housing of 2 measuring clamps is damaged and the battery compartment shows some oxidation (see photos).

Condition: new, Year of construction: 2024, Everything is configurable on demand, very short production & delivery time. We will be happy to provide you with further information on request. Technical data on request. Standard equipment: welded steel construction DURMA CNC control unit (AURORA) Remote control diagnostics (Ethernet) Lantek Software W / Automatic Nesting Position determination of the sheet metal to be cut by laser DURMA Burner height control Double-sided drive system (rack and pinion) AC servo motors for X and Y axis movement Rsdpfx Aefiqgreguscb CNC control outputs/inputs for the filter unit Consumables Starter-Kit Plasma torch * Ignition console * Burner height regulation with Ball screws on double Linear bearings * Special equipment: Hypertherm Max Pro 200 + hose package + nozzles + Durma THC + torch Hypertherm HPR 130 XD + hose package+ nozzles + Durma THC + ignition console + burner Hypertherm HPR 260 XD + hose package+ nozzles + Durma THC + ignition console + burner Hypertherm + Hypertherm HPR 400 XD + hose package + nozzles + Durma THC + ignition console + burner CE Standard Safety wire Automatic gas console for Hypertherm, Manual gas console for Hypertherm, Autogenous cutting torches Plasma torch protection system manual plasma angle cutting head, CNC angle cutting head (+/- 45). Single drilling head Multiple drilling head Filter for 130A, 260A or 400A Pipe cutting unit Ø50 mm - Ø400 mm Additional support for the pipe cutting unit Warning lamp for error and program end With over 60 years of experience

Condition: new, Year of construction: 2024, Everything is configurable on demand, very short production & delivery time. We will be happy to provide you with further information on request. Technical data on request. Standard equipment: welded steel construction DURMA CNC control unit (AURORA) Remote control diagnostics (Ethernet) Lantek Software W / Automatic Nesting Position determination of the sheet metal to be cut by laser DURMA Burner height control Double-sided drive system (rack and pinion) AC servo motors for X and Y axis movement CNC control outputs/inputs for the filter unit Consumables Starter-Kit Plasma torch * Ignition console * Burner height regulation with Ball screws on double Linear bearings * Rodofirx Tepfx Aguecb Special equipment: Hypertherm Max Pro 200 + hose package + nozzles + Durma THC + torch Hypertherm HPR 130 XD + hose package+ nozzles + Durma THC + ignition console + burner Hypertherm HPR 260 XD + hose package+ nozzles + Durma THC + ignition console + burner Hypertherm + Hypertherm HPR 400 XD + hose package + nozzles + Durma THC + ignition console + burner CE Standard Safety wire Automatic gas console for Hypertherm, Manual gas console for Hypertherm, Autogenous cutting torches Plasma torch protection system manual plasma angle cutting head, CNC angle cutting head (+/- 45). Single drilling head Multiple drilling head Filter for 130A, 260A or 400A Pipe cutting unit Ø50 mm - Ø400 mm Additional support for the pipe cutting unit Warning lamp for error and program end D9hnyc97o With over 60 Yes

Year of construction: 2024, condition: new, Machine dimensions: - (L x W x H) 5,240 mm x 3,600 mm x 2,400 mm, - Width with console: 7,700 mm. - Length with filter: 11,000 mm Technical details: - Max. sheet size: 4.000 x 2.000 mm - cutting speed: 12 m/min. - positioning accuracy: ± 0,1 mm - Repeat accuracy: ± 0.1 mm - Power (Hypertherm XPR 170 XD Optimix): 170 A - Cutting area: - Unalloyed steel, piercing, argon: 40 mm - Unalloyed steel, piercing, air: 35 mm - Unalloyed steel, separation cut: 60 mm - Alloy steel, hole piercing: 22 mm - Alloy steel, cut-off: 38 mm - aluminium, hole piercing: 25 mm - aluminium, separation cut: 38 mm Basic equipment: - Control: Durma Aurora CNC controller - Truehole Standard - Sheet metal measurement by laser - Burner height control - AC servo motors for X and Y axis - Software: Lantek, or Metalix Cad/Cam software with Autonesting - 50 pre-programmed part geometries for easy and quick modification. - consumption kit (burner nozzles, etc.) - Plasma torch - ignition console - Remote - Control: Remote maintenance options are included: - Hypertherm XPR 170 XD + Optimix + automatic gas control - Filter for HPR 170 XD - Safety system with circumferential safety wire - Oxyfuel torch with sensor Rodpfx Aedyfwksguscb - Plasma torch - demolition system - Air dryer