Used Powder Painting for sale (4,991)

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Itsdpowzl Hxjfx Adwjb Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: PEF-2.5 PULVER EINBRENNOFEN ELEKTRISCH, temperature: 230 °C, heating capacity: 30 kW (40.79 HP), inner dimension length: 2,500 mm, inner dimension width: 1,505 mm, ✈️ Plus shipping costs – Shipping available upon request.✈️ Fast delivery: Only 6 weeks after receipt of payment! ✅✅✅Energy Class A+++✅✅✅ ✅ Plug & Play system – Delivered fully assembled, ready to use immediately! ✳️ Maintain your liquidity! We offer a variety of financing options to ensure your investment has the best chance of success. Contact us today to learn more about our hire purchase, warranty, or leasing programs. ☘️Environmentally friendly☘️⚡️Green energy⚡️☘️ ⭐ Powder furnace with electric heating - ✔️ Internal dimensions: 2500 mm L * 1505 mm W * 1800 mm H ✔️ Electric heating output: 30 kW/h ✔️ Fan: 3000 m3/h 80 mm SS ✔️ Circulation fan output: 1.5 kW/h ✔️ Total 35 kW/h +- 10% ✔️ Digital heat control, continuously adjustable temperature up to 220°C ✔️ Sandwich panels inside: 1.5 mm galvanized steel, outside: 1.5 mm powder-coated Steel ✔️ Adjustable curing temperature, curing time, and exhaust fan function ✔️ An audible signal sounds at the end of the curing time ✔️ Insulated door with special locking systems (snap lock) ✔️ Insulation: 150 mm (150 mm rock wool) 🔥 PEF-2.5 Curing Oven: Your versatile industrial oven for drying and curing processes! 🔥 Whether powder coating, wet paint, plastic processing, or other thermal processes – the powder curing oven is your reliable solution for professional curing and drying processes up to 230°C! 🌡️ _____ 🚚 Maximum loading flexibility • Compatible with ceiling rail systems • Optionally with insert shelf system for small batches _____ ⚙️ Intelligent control – just the way you need it ✅ PID control (optional) for precise temperature control ✅ Touchscreen control panel & smartphone control 📱 (optional) ✅ Weekly & monthly reports at the touch of a button (optional) Itodpfx Adswfgbrewob ✅ Timer function: freely programmable from 10 minutes to 24 hours ⏲️ ✅ Automatic shutdown after the end of the process _____ ♨️ Ramp heating mode (optional) Precisely control temperature progression and holding times, e.g. E.g.: • Reach target temperature within a defined time • Maintain desired time • Controlled cooling to target temperature • Automatic notifications of process events _____ 🛡️ Safety is our priority 🟢 Safety sensors to prevent overheating 🟢 Automatic shutdown in the event of a fault 🟢 Acoustic warning signals in the event of errors 🟢 Solvent and fume removal via automatic venting _____ ⚡ Customized energy and heating system 🔥 Also available with an extension up to 400°C for high-temperature processes (optional) _____ 🧠 No repeated settings necessary! The furnace saves your process parameters – batch by batch. This saves you time and avoids errors. _____ 📢 And best of all: If you have special requirements – we also build customized furnaces according to your specifications! Contact our team of experts for a personalized consultation! _____ ☀️ 2-YEAR WARRANTY ☀️ Request more information

Condition: used, Year of construction: 1996, Manufacturer : Marchesini Model: MS 235 / AS 237 / BA 50 Year : 1996 Type : 4-seal pouch packaging line for powders. 1. Bagging machine Vertical automatic machine with intermittent movement for filling and sealing bags, for medium and high speed production lines, for powders. Volumetric shaving filler Mechanical speed: 100 strokes/min Range of formats : max reel outer diameter: 400 mm (800 mm with reel) max reel width: 800 mm (820 mm with waste) bag length: 60 to 120 mm Reel support trolley Iodpsx R Alkofx Adwetb Hopper handling trolley Weight: 2100 kg 2. sachet counting unit 3. Cartoning machine Capacity : 70 cartons / minute Dimension A = 40 - 145 mm Size B = 20 - 80 mm Size H = 70 - 190 mm A+B = 190 mm Weight: 900 kg

Condition: new, The AL-KO COLOUR JET paint mist extractor is used to extract toxic mist in the workshop. The AL-KO COLOUR JET is therefore ideal for paint extraction in timber-processing operations, in carpenters' and joiners' workshops and in the craft sector in general. The AL-KO COLOUR JET is a fold-out paint mist extraction system. It is delivered as a plug-in paint mist extraction system. Iodehby Rijpfx Adwjtb Motor 0,75 / 2,1 kW ex/ 400 V / 50 Hz Fan speed 960 / 1.430 RPM capacity 3.000 / 6.800 m3/h dimensions (B/ W/ T) 1.912 x 1.405 x 943 mm with attached side panels 2.971 x 1.405 x 1.215 mm filter area 2 m2 noice level 72,0 dB(A) weight 248 kg

Condition: new, functionality: fully functional, power: 2 kW (2.72 HP), gearing type: automatic, fuel type: electric, color: silver, overall weight: 450 kg, Year of construction: 2025, machine/vehicle number: MZpf001, Equipment: CE marking, The packaging machine can complete the function of material lifting, measuring and weighing, etc. The machine is composed of screw feeding, real-time weighing and dust removal device, etc. It can form a fully automatic production line with bag feeder, heat sealing machine, bag sewing machine, etc. Iodpfx Aoxxn Aujdwetb

Condition: new, Year of construction: 2026, Variable adjustable painting rotary table • Many setting options for small and large massive workpieces • stable • From one person to handle, rigid arms and adjustable swivel arms • Height-adjustable Technical data: Length: 1850 mm Width: 800 mm Height: 1000-1300 mm Load capacity: 300 kg Top goods Can be sent by us via UPS. Must be built then. Itedpfxebzmagj Adweb Location: Off the shelf Bitburg

Condition: new, Year of construction: 2026, Rehnen sprtiz table Lacky The advantages: Itjdpfxolrrrmo Adwob Thanks to its 360° rotatable arms, it always allows the best grip and a good support for all workpieces Easily adjustable in height and 360° rotatable for fast, efficient work Thanks to its covers, even after intensive use, it is still possible to move the arms. Height in mm: 950-1250 Width in mm: 600-1120 Length in mm: 700-1260 Diagonal in mm: 900-1680 Load capacity in kg: 100 Location: ex stock - immediately available -

Condition: excellent (used), Year of construction: 2020, Pneumatic Double Diaphragm Pump Cobra 40-10 Top condition – Year of manufacture: 2020 Its unique design enables low-pulsation operation. Consistent paint flow for a perfect spray pattern and highest surface quality. Ideally suited for processing shear-sensitive and moisture-sensitive materials. Minimal shear forces – ideal for processing, e.g., UV coatings. Ideal for handling small material volumes and frequent color changes. Scope of delivery: Basic unit on frame, HD double hose 7.5 m, upper container 5 l Ex, AirCoat spray gun AC 4600 Professional including red air cap and holder, AirCoat nozzle ACF 3000 11/40. Technical Data: Ratio: 40:1 Iedpfx Adjxdtkujwotb Displacement per double stroke: 10 cm³ Flow rate at 200 double strokes: 2 l/min Max. operating pressure: 250 bar Weight: 23 kg Location: 54634 Bitburg Extremely low hours of use –

Condition: new, Year of construction: 2024, Advantages -Compact design, space-saving -Powerful, high extraction capacity, low operating costs -Easy to maintain, long filter service life -Universally applicable, variable accessories -High flexibility -Mobile design -Suction technology with front plate system Technical data: Nominal motor power: 0,75 kW / 2,1 kW Isdpfxjbpg E Es Adwjtb Motor speed: 960 / 1430 min Air volume: 6 800 m³ / h Filter surface: 2 m² ( 2 x 1 mtr.) Connection diameter 300 mm with throttle valve Dimensions (W / H / D) in mm: 2971 x 1405 x 1215 Weight: 248kg

Condition: new, Year of construction: 2025, Paint mist extraction AL-KO colour Jet 1 Paint mist extraction ready for use, 1 m2 filter surface with pre-and fine filter,. Connection diameter 300 mm, motor 1.5 KW ex (suitable for setting up In zone 22 according to ATEX), switch 1 step + 5 m cable with Plug and Throttle body. Compact space-saving design of sheet steel Chassis with wheels Indirect exhaust near the ground Fully assembled With connecting cable and phase change Setup Adjustable side panels Optimized spray mist recording by patented front sheet cover Long filter service life High-performance fans with low noise level Filter wall with special mats Exhaust socket with integrated butterfly valves Motor power: 1,5 KW Speed: 1400 RPM Nominal flow rate: 4600 m3/h Pressure: 500 PA Dimensions: (W * H * D) 1025 * 1437 * 1214 W = 2000 mm with side panels Filter surface: 1 m2 Isdpfx Aobumr Ssdwjtb Weight: 175 kg

Condition: new, Year of construction: 2026, Variable adjustable painting rotary table • Many setting options for small and large massive workpieces • stable • From one person to handle, rigid arms and adjustable swivel arms • Height-adjustable Technical data: Length: 1850 mm Width: 800 mm Height: 1000-1300 mm Itsdpsbzmafsfx Adwob Load capacity: 300 kg Location: Off the shelf Bitburg Top products at great prices Can we be - sent via UPS must be established.

Condition: refurbished (used), functionality: fully functional, machine/vehicle number: ZSCT-II (Bj.2014) + ZSCT-III (Bj.2019), overall weight: 570 kg, Year of construction: 2014, power: 4.5 kW (6.12 HP), We are offering a fully refurbished Iversen graphic ZSCT-II powder coating machine, year of manufacture 2014, for a negotiable net price of €14,000. In addition, we have an Iversen graphic ZSCT-III powder coating machine, year of manufacture 2019, available for a negotiable net price of €7,900, not refurbished but in working condition. As a special bonus, you will also receive a complimentary Iversen graphic ZSCT-III powder coating machine, year of manufacture 2016, provided as a donor for spare parts. Dimensions can be seen in the attached image. Model number: ZSCT-II Voltage: 380 V Power: 2–4.5 kW Belt width: 1000 mm Belt length: 1000 mm Isdpfxex Uqbnj Adwetb Sheet thickness: 1–5 mm Overall dimensions: 2000 × 1800 × 1850 mm Net weight: 570 kg Model number: ZSCT-III - Year 2019 - 91/0150 Voltage: 380 V Power: 3.1 kW Pressure: 8 bar Model number: ZSCT-III - Year 2016 - 51/0116 (for spare parts) Voltage: 380 V Power: 3.1 kW Pressure: 8 bar If you have any questions or require further information, please do not hesitate to send us a message or call us.

Condition: used, Year of construction: 2001, Baffle width: 4000 mm. Baffle height: 1000 mm. External dimensions: 4600 x 1500 mm. 2 x 1.5 kW motors. Total nominal flow rate: 7000 m³/h. Right and left exhaust nozzles with 300 mm diameter. Itedsvvizkopfx Adwob Storage location: Garbsen

Condition: ready for operation (used), Year of construction: 2017, Gebr. Wagner Puma 28-40 Airless Year of manufacture: 2017 Wagner 28-40, air-operated piston pump with AirCoat equipment – used This unit is pre-owned Technical details Pressure ratio: 28:1 Max. air inlet pressure: 8 bar Max. output: 2.4 l/min Max. pressure: 224 bar Max. nozzle size: 0.023" Scope of delivery Wagner Puma 28-40 AC with wall bracket on pallet truck 7.5m material hose DN4, 250 bar Wagner spray gun Nozzle The unit is suitable, among other applications, for processing the following materials: Isdpfx Adsx N E Tzowetb Clear coats Paints Glazes Stains Fillers Acrylic paint

Condition: ready for operation (used), Year of construction: 2016, Gebr. Wagner Piston Pump Leopard 35-70 - Spraypack Airless -+ Year of manufacture: 2016 Technical data: Iedpfox N E Sqjx Adwotb Transmission ratio: 35:1 Max. air inlet pressure: 7.1 bar Max. working pressure: 250 bar Displacement per double stroke: 70 cm³ Max. stroke rate: 60 DH/min Max. delivery rate: 4.2 l/min Air consumption at 6 bar per double stroke: 18.6 nl - immediately available -

Condition: used, Year of construction: 2006, functionality: fully functional, machine/vehicle number: 13-3188, total length: 1,60,000 mm, total height: 3,000 mm, total width: 9,000 mm, temperature: 230 °C, volume flow: 100 m³/h, Powder Coating System ARNO HERING PTR 15-45-SE (Year 2006) For sale is a complete powder coating system from ARNO HERING (model PTR 15-45-SE), manufactured in 05/2006. The system consists of an application booth, drying/curing oven, and crane rail/carrier racks (hanging racks). The system is from ongoing production and is suitable for coating metal parts and assemblies. Highlights / Equipment (Components): - Application booth (powder application) - Drying oven / curing oven - Crane rail / manual overhead conveyor system including carrier/hanging racks - Documentation/control manuals: to be included if available Technical Data (according to nameplate): - Model: PTR 15-45-SE - Year of manufacture: 05/2006 - Machine number: 13-3188 - Max. drying temperature: 230 °C - Minimum exhaust air volume (at 20 °C): 100 m³/h - Max. permitted powder quantity: 10 kg/h Notes: - Inspection on site is possible by appointment. Itjdjx Squ Aopfx Adwjb - Loading/dismantling: by arrangement (possibly to be handled by the buyer). - Sale ex location, subject to prior sale. We are offering this used ARNO HERING PTR 15-45-SE powder coating system, year 2006. Model: PTR 15-45-SE Year: May 2006 Machine number: 13-3188 Maximum drying temperature: 230 °C Minimum exhaust air volume at 20°C: 100 m³/h Maximum permitted powder quantity: 10 kg/h If you have any questions or need further information, please feel free to send us a message or call us.

Condition: used, Year of construction: 2003, functionality: fully functional, Wet Paint Coating System KRAUTZBERGER SPRITZTECHNIK incl. Coalescence Unit RODAP SR 185, Year 2003 Used wet paint coating system for surface finishing of metal parts (including decorative fittings/series parts). The system consists of the spraying technology by Krautzberger as well as a coalescence/separation unit RODAP SR 185 for processing/separating (e.g. overspray/mist extraction, depending on configuration). The scope of delivery also includes spray trolleys and various suspension racks for flexible part handling and series production. Application area: Wet painting / spray coating of metal components and assemblies. Scope of delivery: Krautzberger spray technology + RODAP SR 185 + spray trolleys + various suspension racks. Inspection: by appointment (electrically connected possible by arrangement). Dismantling/loading: by purchaser or as agreed. Iodpfx Adox Sqtrjwotb

Condition: excellent (used), mileage: 20,170 km, power: 169 kW (229.78 HP), first registration: 12/1999, fuel type: diesel, axle configuration: 4x2, fuel: diesel, color: red, gearing type: mechanical, emission class: euro2, suspension: steel, total length: 8,400 mm, total width: 2,300 mm, total height: 2,870 mm, Year of construction: 1999, DUTCH TRUCK IN EXCELLENT CONDITION, ONLY 20,000 KM MANUAL GEARBOX = Further Information = General Information Cab: double Axle Configuration Suspension: leaf springs Front axle: steered Rear axle: twin wheels Weights Unladen weight: 11,900 kg Payload: 6,850 kg Gross vehicle weight: 18,750 kg Itsdjxvqgkepfx Adwjb Condition Technical condition: very good Visual condition: very good Further Information Please contact Thierry Leemans for more information.

Condition: new, Year of construction: 2026, functionality: fully functional, Specifically designed for small businesses and rim coaters. The system is complete and consists of: Powder oven (W x H x D) 1200 x 1600 x 1200 mm, 15 kW; Powder coating booth (W x H x D) 2000 x 2240 x 920 mm; Latest powder gun from the ROMER ProfiSpray series. All together for €16,990.00 net, plus freight and installation. Itedsg Ngt Nopfx Adweb

Condition: good (used), Item: A-01208-Powder-silos Vertical Stainless Steel Powder tank Capacity 45.000 l/each Exterior dimensions: Dia Ø 2860 mm Total H 9000 mm. Cylinder height 6500 mm. Vertical stainless steel tank - 2 pcs. 30 degrees conical bottom, 15 degrees conical top and manhole at side of bottom. Quality: AISI 304 Itedpoiiyuujfx Adwjb

Condition: good (used), Year of construction: 1985, total height: 2,000 mm, overall weight: 150 kg, total length: 1,300 mm, total width: 1,000 mm, inner dimension height: 950 mm, inner dimension width: 900 mm, inner dimension length: 1,100 mm, Paint spray booth for small parts / color samples, exhaust air volume 3100 m3/h, motor 0.75 KWDimensions 1000x1300x2000 mm, approx. 150 kg Iedpfx Adovl H Sfswetb

Condition: new, Year of construction: 2026, Internal dimensions LxWxH 4300x1700x2200mm, Temperature max. 220°C, oil, gas or electrical heated possible, Tracks for hordes waggons possible, Iodpfx Adsizw E Ujwetb Manual or automatic transport usable, flap or sliding doors producable.

Condition: new, Year of construction: 2026, Wetpaint Spray-/ Dryingcabine Internal dim. L8000 x B4000 x H3000mm 30.000m³/h Inletair/ 30.000m³/h evaporation Internal Temp. 20°C man. adjustable, Drying Temp. up to 70°C Iedpfxjhzbq Tj Adwstb Indirect Gasburner approx 300KW (-10°C - +20°C) Software in delivered switch box Inlet air ceiling with filter G4/EU4 und NF600PA, Outside air bollom using grids and PS50 glas fiber Light (4x18W) wall integrated LED, 750LUX Grid point weight max750kg

Condition: new, Year of construction: 2026, Some components can be choose: - chamber pretreatement with osmosis plant, - Water drier oven, - Powder curing oven, - manual transportsystem inkl. steel frame, - Controler siemens, Itjdpfxjizw Hno Adwob Additionsal chooseable components possible.

Condition: new, Year of construction: 2026, Powder coating booths, sizes defined by customer, Ijdpfjizw Hyex Adwotb Additional equippment possible.