Used Rigidly for sale (10)

Condition: used, Year of construction: 2007, functionality: fully functional, overall weight: 221 kg, input voltage: 400 V, input frequency: 50 Hz, input current: 54 A, Device No. 1: KSB Blockp Etabloc 65-200/3002 GN10 Fpjdpfx Adsxbhtleaed IEC standard motor KSB 30 kW 2900 rpm Part No.: 48875108 Single-stage volute casing pump with rated capacities according to EN 733, fitted with KSB IEC three-phase motor, protection class IP 55, insulation class F, assembled as a block unit. Pump shaft rigidly coupled to motor shaft. Equipped with uncooled mechanical seal, corrosion-resistant shaft sleeve, replaceable wear rings. Drive lantern made of cast iron, with contact protection in accordance with EN 294. Mounting by support foot up to motor size 112, by motor foot from motor size 132 upwards. Volute casing: Cast iron Impeller: Cast iron Shaft, pump: Tempered steel

Condition: good (used), KSB Pump Etaline GN 065 - 160/114 Inline pumps and three-phase standard motor with motor-mounted frequency converter for stepless speed adjustment. Areas of application: Heating systems Air-conditioning systems Cooling circuits Domestic hot water systems water supply industrial circulation systems Materials to be pumped Fluids that do not chemically or mechanically attack the pump materials. Operating data 1450 min Design Close-coupled pump in in-line design, with variable-speed standard motor, pump shaft and motor shaft are rigidly connected. Bearings Deep groove ball bearing grease lubricated. Shaft seal uncooled and maintenance-free mechanical seal according to EN 12 756 Fpjdpeivd Dkefx Adajd Drive surface-cooled three-phase standard motor with motor-mounted frequency converter and radio interference filter according to DIN EN Pump series: Etaline Material combination: cast iron Standard motor and stub shaft Size designation: 65 Nominal width suction/ discharge 160 Item condition: used

Condition: good (used), KSB Pump Etaline GN 080-210/404 G11 Inline pumps and three-phase standard motor with motor-mounted frequency converter for stepless speed adjustment. Areas of application: Heating systems Air conditioning systems Domestic hot water systems water supply systems industrial circulation systems Materials to be pumped Fluids that do not chemically or mechanically attack the pump materials. Operating data Q to see data sheet H to see data sheet For the data of this pump, please refer to the data sheet 1) The sum of inlet pressure and delivery head at zero flow must not exceed the specified exceed the specified value Design Close-coupled pump in in-line design, with variable-speed standard motor, pump shaft and motor shaft are rigidly connected. Bearings Fpjdpfx Adeiu U Txoaod Deep groove ball bearing grease lubricated. Shaft seal uncooled and maintenance-free mechanical seal according to EN 12 756 Pump series: Etaline Material combination: cast iron Standard motor and stub shaft Size designation: 80 Nominal width suction/ discharge 210 For further technical data, please refer to the data sheet. Item condition: used Scope of delivery: 1 x KSB pump Etaline GN 080-210/404 G11

Condition: good (used), KSB pump Etaline GN 050-160 / 074 G10 Inline pumps and three-phase standard motor with motor-mounted frequency converter for stepless speed adjustment. Fpodpfx Aod Sqkzedajd Applications: heating systems air conditioning Water systems water supply industrial circulation systems conveyed Liquids that do not attack the pump materials chemically and mechanically. operating data Q 17,50 m3 / h H 5.8 m Further data of this pump can be found in the data sheet 1) The sum of inlet pressure and delivery head in the zero point of quantity may be said to Do not exceed the value execution Block pump in inline design, with variable-speed standard motor, pump and motor shaft are rigidly connected. camp Deep groove ball bearing grease lubricated. shaft seal uncooled and maintenance-free mechanical seal according to EN 12 756 Pump series: Etaline Material combination: gray cast iron Standard engine and stub shaft Size designation: 65 Nominal diameter suction / discharge connection 160 Further technical data can be found on the data sheet. Item condition: used Scope of supply: 1 x KSB pump Etaline GN 050-160 / 074 G10

Condition: new, Year of construction: 2026, Weima Briquetting Press TH 714 The TH 714 machines are designed for plants with required throughput rates of up to 150 kg/h. The stable press housing enables the production of high-strength briquettes - from materials such as wood, polystyrene, foams, light metals, paper or biomass. Numerous additional options can be implemented, e.g. oil cooling for multi-shift operation. All machines are available as left- or right-hand version. Mounting on a stable base frame ensures fast installation and makes mobile use possible. User-friendly operation thanks to Siemens PLC control In order to live up to our performance promise, we design and produce all control cabinets ourselves at our Ilsfeld site and equip them with well-known international components. This guarantees highest quality with compact design. The used PLC-control from Siemens is perfectly adapted to the requirements of the briquetting process. Impurity-resistant screw conveyor due to cardanic suspension The screw conveyor, which transports the material into the pre-compressor of the briquetting press, is suspended on a cardan joint. This prevents interfering materials from causing damage to the screw conveyor. As is so often the case, however, it always depends on the specific application which suspension is chosen. For metal applications, for example, we often recommend rigidly mounted screws. Briquette diameter (mm): 70 Throughput capacity up to (kg/h): 150*1 Fodpfxjil Hggs Adaspd Hydraulic motor (kW): 11 Oil quantity (liters): 250 Weight (approx. kg): 1100 Location: Ex stock 54634 Bitburg - immediately available - subject to prior sale

Condition: used, empty load weight: 28,700 kg, overall weight: 98,000 kg, axle configuration: > 3 axles, first registration: 07/2009, next inspection (TÜV): 05/2026, tire size: 285/70 R19,5, color: yellow, Equipment: ABS, Hydraulically liftable and lowerable gooseneck • Ball bearing turntable-mounted fifth wheel plate, 3 1/2" kingpin and adjustable steering wedge • Built-in hydromechanical double steering for steering pendle axles (dual-circuit steering, 4 hydraulic cylinders) • Hydraulic lift and lower function, hydraulic differential lock • Hydraulic connection for tractor unit Shaped loading platform (approx. 3,600 x 2,480 mm) with checker plate covering and chamfered front corners • Designed for a technical fifth-wheel load up to 30 t Steering radius approx. 2,500 mm Controls for hydraulic functions located on the left in the direction of travel, incl. folding protective cover Fpedpfex Sragox Adasd Gooseneck mounted directly onto the chassis for the shortest possible construction length and rigidly welded in place GOLDHOFER 2-axle running gear with THP/ET special axles permanently fixed to the hydraulic gooseneck two single-tire pendle axle units with hydraulic axle compensation with a total of 4 wheels per axle line Tyre size 285/70 R 19.5 150/147 J TL Chassis width 2,750 mm, wheelbase 1,360 mm Technical axle load per axle line max. 14 t (at 70 km/h) Maximum steering angle of the pendle axles approx. 70 degrees Loading height at mid position 1,240 mm (loaded) Hydraulic axle lift ±300 mm Dual-circuit hydromechanical steering system Two-line full-air brake system with spring-loaded parking brake, ALB brake and automatic slack adjusters (AGS) ABS brake (anti-lock braking system, Wabco make) Hose burst safety valves on all axles Hydropneumatic gas storage suspension can be deactivated when loaded Rear frame-integrated adapter element in a short and narrow compact design for connecting between chassis and flatbed deck Errors excepted

Condition: used, Year of construction: 2018, Nominal pressing force: 4,000 kN Ram stroke, adjustable in increments: 30 ... 160 mm Ram adjustment: 180 mm Fsdpfx Adjw Rbxzeajpd Throat depth: 515 mm Strokes per minute (idle): 45 / min Option: Infinitely variable stroke rate: 10 … 60 / min Die installation height at maximum stroke, bottom dead center, and ram fully raised: 660 mm Table clamping surface (W x D): 1,700 x 1,000 mm Table height above floor: 1,005 mm Ram clamping surface (W x D): 1,100 x 800 mm Pin bore in ram: 65 mm Main motor power: 45 kW Approximate machine height: 4,325 mm Machine weight: 33,000 kg Control system – Press safety control with redundant design and self-diagnosis, featuring plain text status and error display Infinitely variable stroke rate in the range of 10 ... 60 strokes/minute via ABB frequency inverter Control variant: TFT color touchscreen including electronic cam controller with die management and die protection, with color touchscreen visualization, SIEMENS PLC S7-300, die data management, counting systems, data transmission via Profibus Fully automatic stroke adjustment / ram adjustment Rigidly welded tie rods, clear distance between tie rods: 1,345 mm Swiveling main control console Non-contact safety guard – BWS brand LUMIFLEX, mounted at the front of the machine table or die area, installed on the tie rods

Condition: new, Year of construction: 2025, functionality: fully functional, Cutting area: 5300 x 2240/2100 x 80 mm Cutting depth: 80 mm Electronic positioning system EPS.x Scoring saw unit, stepless adjustment Paper holder Small parts support made of aluminum Free-standing supports Saw frame • Machine components manufactured with a precision of 1/100 mm Fpodpfxjx Irrzs Adajd • Heavy-duty, self-supporting, rigidly welded, torsion-resistant saw frame • TRK1 full-surface support wall made from birch multiplex with integrated small parts tray • Auxiliary stop profile with its own measuring tape and 3 auxiliary stops for repeat cuts • Automatic detection of the center support • Automatic roller locking during cutting Saw beam • Sturdy, long-lasting steel saw beam construction • Automatic saw beam locking with cut position detection Saw unit • Play-free, smooth-running guideways • Robust bearing of the motor carriage ensures high cutting precision • Powerful 5.5 kW (7.5 HP) motor with high torque • Maximum comfort thanks to largely automated operation • Laser-assisted indication of horizontal cuts • Automatic motor carriage clamping • Automatic immersion and tilting of the saw motor • Pneumatic coupling enables easy switch to manual mode • SUPERSILENT sound insulation for reduction of saw blade noise • Electromagnetic motor brake • ProLock Easy-Fix tool clamping system Control system • 12" touchscreen computer with optimum user interface • Multilingual user guidance • Tool database ensures maximum flexibility and absolute repeat accuracy • Fully automatic sawing process • Infinitely variable feed speeds: 10–25 m/min • Selectable sawing cycle • Panel end detection • Constant return speed • Operating hours counter • Network connectivity • 24VDC UPS for touch PC (uninterruptible power supply) • Automatic saw beam positioning (ASP) Dimension setting • Digital measuring system DMS.x (horizontal axis for vertical cuts) • Electronic positioning system EPS.y incl. ABO (vertical axis for horizontal cuts) Design, ergonomics • Typical STRIEBIG product design • Multiple award-winning (including Design Prize Switzerland) • Function- and operator-oriented ergonomics Installation • Can be wall-mounted or free-standing

Condition: as good as new (ex-display), operating hours: 80 h, functionality: fully functional, axle configuration: 6x6, Equipment: all wheel drive, second-hand vehicle warranty, Drum chipper type BBT 800 rigidly mounted on a MAN truck including a timber loading crane and an external diesel engine for all the hydraulics. Fpodpfx Adeq Ht Tbsaod Technical data chipper: Rotor diameter: 800mm Number of rows of blades: 1 Number of blades: 4 Counter blades: 1 Bottom sieve: 1 Feed opening (W x H): 980 x 700mm Grain size: G15 - G50 Drive from the truck: 370 KW Discharge of the wood chips: conveyor belt, swivels 180° left/right Mounting type: rigid on a truck Truck type: MAN TGS 33.500 6x6 BB Timber loading crane: Palfinger type: S100F101 Incl. Epsilon 4-finger gripper FG31R The chipping is carried out by a closed chipping rotor. The entire machine is a robust steel construction, made from high-quality steel and is designed for extreme continuous use and the toughest conditions. All bearing housings of the feed rollers and the chipping drum are made from steel. The chipping machine can be operated directly from the truck cab. Wood Cracker L70 splitting device The conveyor belt is telescopic in length. Available immediately

Condition: good (used), Year of construction: 2012, DEMAG crane chain hoist DCM-Pro 2 80 1/1 H2.8 V16/4 80 kg with crane canopy (2x3m) The DCM-Pro manulift was developed for safe and fast load handling with one-hand operation. The DCM-Pro is based on the lifting unit of the DC-Pro chain hoist and the DSM-C control unit. Due to the control unit being rigidly connected to the load handling attachment, the operator only needs one hand to operate the chain hoist as well as to guide the load. Manufacturer: DEMAG Type: Crane chain hoist Model: DCM-Pro 2 80 1/1 H2.8 V16/4 Load capacity: 80 kg Control: GSA Type 4 Movement radius: sideways 3 metres and forwards/backwards 2 metres Fedpfohwd E Njx Adajpd Steel beam: included in the offer Condition: used  Complete factory closure, large selection of storage platforms, pallet racks, shelf racks, paternosters. High-quality industrial machines, lathes, grinding machines, hand machines. Further articles - new and used - you will find in our shop! International shipping costs on request!