Used Scanner for sale (322)

Year of construction: 2026, condition: as good as new (ex-display), machine/vehicle number: S23Synthesi01, Stretch Winder Synthesi Gedpfx Absykuddehoip TECHNICAL DETAILS Turntable / base frame / Ø 1,500 mm Max. pallet dimensions: 800 x 1,200 mm Max. load capacity: 2,000 kg Wrapping height (pallet included) 2,200 mm Height of turntable 75 mm Height query by light button Frequency-controlled turntable drive (soft start - start/stop) Frequency controlled carriage speed up/down Signal tone at the start of wrapping and stop at the end of the cycle Emergency stop switch according to CE regulations The turntable always stops in the same starting position Fall protection for the film slide Push button for switching on the machine and start & stop function & reset according to CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL All function parameters can be set via the display F00 - Screen lock program change F02 - Infinitely variable turntable speed 5-12 rpm Lifting carriage speed can be adjusted up and down independently of each other F03 - lifting carriage speed up from 1.3 up to 5.4 m/min F04 - carriage speed down from 1.3 to 5.4 m/min F05 - Number of wraps on the pallet foot (1 - 10 wraps) F06 - number of wraps on the pallet head (1 - 10 wraps) F09 - Winding height photocell delay F13 - F16 - Foil application tension foot & head wrapping / ascent & descent independently adjustable F62 - Ergonomic height for film change Foil consumption display (optional) ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL 6 storable winding programs F01 - 1 - cross winding (up/down) F01 - 2 - Single wrap (only up or only down) F01 - 3 - Push button for manual functions F10 - F11 - Wrap cycle with preset start and stop height F12 - Winding to a stored height (switching off the light button for the height) F22 / F23 - Winding cycle for cover sheet film F29 - Soft start cycle for edge protection application F30 - F31 - Wrap cycle with gain and adjustable number of wraps Soft start to reduce film tears on sharp pallet edges Winding cycle with manual or motorized line formation (optional) Reinforcement cycle via push button FILM SLIDE TYPE “FM” WITH MECHANICAL BRAKE via manually adjustable brake roller on the foil carriage Foil specification Max. outer diameter Ø 250 mm - core Ø76mm - height = 500 mm Standard connection values: 230 V - 1L+N+PE - 50 HZ Total power: 1.2KW / 6A Optionally possible: FILM SLIDE TYPE "OPRS - ONE PRE STRETCH" Film pre-stretch ratio set to 200% Turntable size up to Ø2600 mm Mast height up to 3900mm ramp mounting frame Light scanner for black products cutting device Etc. Other systems available from the Ludwigsburg warehouse. Some images may contain options that are subject to a surcharge.

Year of construction: 2026, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: S25EVA01, Stretch wrapper EVA TECHNICAL DETAILS Turntable / base frame / Ø 1,500 mm Max. pallet dimensions: 800 x 1,200 mm Max. load capacity: 1,500 kg Wrapping height (pallet included) 2,200 mm Height of turntable 75 mm Height query by light button Frequency-controlled turntable drive (soft start - start/stop) Frequency controlled carriage speed up/down Signal tone at the start of wrapping and stop at the end of the cycle Emergency stop switch according to CE regulations The turntable always stops in the same starting position Fall protection for the film slide Push button for switching on the machine and start & stop function according to CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL All function parameters can be set via the display F02 - Infinitely variable turntable speed 5-12 rpm Lifting carriage speed can be adjusted up and down independently of each other F03 - lifting carriage speed up from 1.3 up to 5.4 m/min F04 - carriage speed down from 1.3 to 5.4 m/min F05 - Number of wraps on the pallet foot (1 - 10 wraps) F06 - number of wraps on the pallet head (1 - 10 wraps) F09 - Pallet wrapping height setting F62 - Ergonomic height for film change ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL 1 storable wrapping program F01 - 1 - cross winding (up/down) F01 - 2 - Single wrap (only up or only down) F01 - 3 - manual winding F12 - winding to a stored height (while switching off the light button) F29 - Soft start cycle for edge protection application Soft start to reduce film tears on sharp pallet edges FILM SLIDE TYPE “FM” WITH MECHANICAL BRAKE via manually adjustable brake roller on the foil carriage Gedoykucyopfx Abhoip Foil specification Max. outer diameter Ø 250 mm - core Ø76mm - height = 500 mm Standard connection values: 230 V - 1L+N+PE - 50 HZ Total power: 1.2KW / 6A Options: Turntable 1650mm ramp mounting frame Light scanner for black products Other systems available from the Ludwigsburg warehouse.

Year of construction: 2026, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: S25Synthesi01, Stretch Winder Synthesi Godpfxjykub Aj Abhjip TECHNICAL DETAILS Turntable / base frame / Ø 2,200 mm Max. pallet dimensions: 1,550 x 1,550 mm Max. load capacity: 2,000 kg Wrapping height (pallet included) 2,200 mm FILM SLIDE TYPE "OPRS - ONE PRE STRETCH" Film pre-stretch ratio set to 200% Foil application tension electronically adjustable in the programs in different steps Height of turntable 75 mm Height query by light button Frequency-controlled turntable drive (soft start - start/stop) Frequency controlled carriage speed up/down Signal tone at the start of wrapping and stop at the end of the cycle Emergency stop switch according to CE regulations The turntable always stops in the same starting position Fall protection for the film slide Push button for switching on the machine and start & stop function & reset according to CE standards Ø 22 mm ADJUSTABLE PARAMETERS ON THE CONTROL PANEL All function parameters can be set via the display F00 - Screen lock program change F02 - Infinitely variable turntable speed 5-12 rpm Lifting carriage speed can be adjusted up and down independently of each other F03 - lifting carriage speed up from 1.3 up to 5.4 m/min F04 - carriage speed down from 1.3 to 5.4 m/min F05 - Number of wraps on the pallet foot (1 - 10 wraps) F06 - number of wraps on the pallet head (1 - 10 wraps) F09 - Winding height photocell delay F13 - F16 - Foil application tension foot & head wrapping / ascent & descent independently adjustable F62 - Ergonomic height for film change Foil consumption display (optional) ADJUSTABLE WRAPPING PROGRAMS ON THE CONTROL PANEL 6 storable winding programs F01 - 1 - cross winding (up/down) F01 - 2 - Single wrap (only up or only down) F01 - 3 - Push button for manual functions F10 - F11 - Wrap cycle with preset start and stop height F12 - Winding to a stored height (switching off the light button for the height) F22 / F23 - Winding cycle for cover sheet film F29 - Soft start cycle for edge protection application F30 - F31 - Wrap cycle with gain and adjustable number of wraps Soft start to reduce film tears on sharp pallet edges Winding cycle with manual or motorized line formation (optional) Reinforcement cycle via push button Optionally possible: Turntable size up to Ø2600 mm Mast height up to 3900mm ramp mounting frame Light scanner for black products cutting device Etc. Other systems available from the Ludwigsburg warehouse. Some images may contain options that are subject to a surcharge. Illustration similar

Year of construction: 2007, condition: good (used), Chemagen chemagic Magnetic Separation Module I The chemagic Magnetic Separation Module I (chemagic MSM I) automatically isolates nucleic acids within one hour. Viral RNA from 96 nasal swabs can be isolated simultaneously. The Chemagen MSM-1 is an automated system for high-throughput nucleic acid (DNA/RNA) isolation. It utilizes patented Magnetic Bead Technology, in which magnetizable metal rods are immersed in the process solutions to efficiently collect and resuspend the bound particles. Technical Features & Capacity Throughput: The system has a modular design and can process 12, 24, or 96 samples simultaneously, depending on the rod head used. Sample Volume: It offers high flexibility for volumes from 10 µl to 10 ml. Processing Time: 96 samples (small volumes): approx. 15–60 min. 24 samples (medium volumes): approx. 35–60 min. 12 samples (large volumes): approx. 45–60 min. Technology: Particle resuspension is achieved by rotating the metal rods at up to 2,000 rpm, enabling high yield and purity without cross-contamination. System Components & Extensions Automation: The MSM-1 can be integrated into standard liquid handling units and often features a 6-axis industrial robot for fully automated sample tracking. Software: The system is controlled by chemagic QA software, which is LIMS-compatible. Applications The device is primarily used in research and diagnostics, including: Biobanking and human genetics HLA typing Detection of viruses and bacteria Extraction from various materials such as whole blood, saliva, serum, or plasma System Components Actuators: High-precision linear axes for vertical movement and a rotary axis for mixing Electromagnet: Central unit for controlling the magnetic attraction to the metal rods Interfaces: Integrated PC with screen, keyboard, and barcode scanner for sample tracking Software: chemagic QA software (LIMS-compatible, logging, user management) Special Features Cross-contamination protection: The use of disposable protective sleeves (tip combs) for the metal rods prevents contact between samples. Automation: Can be combined with the chemagic dispenser for automated buffer filling or integrated into liquid handling robots (e.g., Hamilton, Tecan). Probe heads: 96 Sample volume: 10 - 400 μL Number of samples: 1 to 96 samples TFT monitor, keyboard, and mouse Year of manufacture: 2007 Dimensions & Setup Basic machine (W/D/H): approx. 600 x 640 x 950 mm. Carrier axis (W/D/H): 1940 x 170 x 200 mm (with full expansion and rail system). Total space requirement: A fully configured system can require up to 2000 x 740 x 800 mm (L/W/H). Financing through our bank is also available. komplett-konzept.leasingo.de Gedpfx Abeyk Uu Nehsip Find more items – new and used – in our shop! International shipping costs on request!

Condition: excellent (used), Year of construction: 2017, operating hours: 40 h, functionality: fully functional, input voltage: 230 V, total width: 1,600 mm, total length: 1,200 mm, total height: 2,100 mm, overall weight: 900 kg, workpiece weight (max.): 100 kg, For sale is a Zeiss ScanBox 4105 equipped with an Atos Q 12M 3D sensor, a high-precision optical 3D scanner designed for demanding measuring and inspection applications, fully automated within a robotic cell. The robotic cell was manufactured in 2017 and retrofitted in 2024 with a new Atos Q 12M 3D sensor. The system has seen little use and is in nearly new condition. The robotic cell has logged only 40 operating hours (axis movement). Giodpfx Aboyir Hyohop The sensor is fitted with the MV170 measuring volume. Included in the scope of delivery are a mobile controller and a tripod, as well as the original transport case for the sensor, allowing for flexible and manual use of the sensor outside the robotic cell. The supplied software package includes Zeiss Inspect Professional and Zeiss Blade Inspect. All original manuals and documentation are also included.

Condition: used, Year of construction: 2013, functionality: fully functional, machine/vehicle number: 130304, GOM ATOS II Triple Scan - Industrial Blue Light Optical 3D Scanner {CEE ID: 7494} GOM Year: 2013 System includes lenses and calibration plates for the following measurement volume sizes: 320 mm 170 mm Travel roller cases for measuring head, lenses, accessories, and tools. Computer - Dual Xeon processor, 32 GB RAM, RAID hard drives Metal-enclosed reinforced case for computer equipment. Gedpfjyfgn Dox Abheip Installed software ATOS Professional v8, includes: GOMInspect V1.2.1 Online system manuals. Copy of original software on CD FOBA AROBE studio / camera stand - 12-foot height with 2M horizontal arm, rotating column, and tilting head. Printed manual, CD with test reports and calibration plate data for each calibration plate Rotary table (manual) Parts set (touch probe)

Condition: ready for operation (used), Year of construction: 2019, operating hours: 200 h, functionality: fully functional, type of input current: AC, laser power: 700 W, power: 3 kW (4.08 HP), Equipment: cooling unit, cw fiber laser with 750 watts as a stand-alone system or for integration into machines and systems. Due to its high output power, this water-cooled laser is particularly suitable for tasks where a lot of heat is required in the workpiece. This includes, for example, welding metals or plastics, cutting, material removal or structuring. The optional use of a 2D galvo scanner means that the laser beam can also be guided over the workpiece using software. The laser can be modulated digitally and analogue (power setting) and can also be controlled and monitored using control software. The images show a setup with a galvo scanner. The system can also be optionally equipped with a welding head or cutting head. Laser class 1 can also be achieved by installing side walls and a front door with a laser protection window (all available). The work area can be adjusted in height using an electrically controlled Z axis. The laser system is prepared for integration into a higher-level system, but can also be used as a stand-alone system. In the event of integration, interfaces for interlock, emergency stop, external laser control, etc. are available. Individual components of the system can also be integrated into a system at the customer's site. We are happy to support the customer after consultation and according to their specifications. Some technical data: - maximum 700 watts optical output power - wavelength: 1080 [nm] - power consumption (without cooler): < 3,000 watts - supply: single-phase; 230 VAC / 50 Hz Gjdpfx Abeph U Anehsip - analog modulation (can be used to adjust power, among other things) - digital modulation up to 20 kHz

Condition: excellent (used), Year of construction: 2008, SSI Schäfer Roller Conveyor System The price already includes over €25,000 in dismantling costs. The 8 roller conveyors shown in the second image are not included in the delivery. Logistics Center - Conveyor Belts, Roller Conveyors & Spare Parts. Excluding peripheral equipment such as printers, scanners, binding machines, shelving, etc. Over 3 floors Gijdpfjk Hz Dasx Abhep Year of manufacture 2008 Extensive documentation Further images, sketches, and videos are available; we will gladly send you a link upon request. The Schäfer roller conveyor system is a state-of-the-art conveyor system specifically designed for the efficient and precise movement of goods and products across multiple floors. With its robust construction and intelligent control system, the system offers a reliable and flexible solution for internal transport in production facilities, logistics centers, and warehouses. The roller conveyor system consists of a series of rollers arranged horizontally and vertically to ensure seamless movement of goods between different levels. By using individually adjustable rollers and various conveyor belt types, the system can be adapted to the specific requirements of each customer. The Schäfer roller conveyor system features intelligent controls that allow for precise monitoring and management of the transport process. The control system can automatically adjust various settings and operating modes to ensure optimal performance and seamless integration into existing production processes. The system is easy to install and maintain and can be easily adapted to different spatial and floor layouts. The Schäfer roller conveyor system offers a reliable and effective solution for the internal transport of goods and products across multiple floors, making it an ideal investment for companies looking to optimize their internal transport and increase productivity. Financing through our bank is also available. komplett-konzept.leasingo.de Find more items – new and used – in our shop! International shipping costs available upon request!

Condition: excellent (used), Epson G10-854SR Robot Assembly Station and Dispensing Station The assembly station is divided into the following sub-stations: 3.1 Dispensing Area, 3.2 KK+SW Assembly Area, and 3.3 Front Assembly Area. (KK = Heat Sink, SW = End Wall Bracket) St. 3.1: Dispensing Area: - A workpiece carrier (WT) with mounted chassis and PCBs enters the dispensing area via the transfer belt. - It is stopped at the lifting-positioning unit (HuPo), lifted off the belt, and fixed in place. - The X-Y-Z handling moves the dispensing head to the designated position and starts the dispensing process. - After successful dispensing, the handling moves to the rest position, and the WT is placed back on the belt. - Continued transfer to the KK+SW assembly area (provided there is no WT in the mounting position). St. 3.2: KK+SW Assembly Area: - A WT from the dispensing area arrives in the KK+SW assembly area via the transfer belt. - It is stopped at the lifting-positioning unit (HuPo), lifted off the belt, and fixed in place. The chassis side walls of the partially assembled unit are aligned. - KK tray and SW tray positioning occurs simultaneously. - A stack of 12 KK trays and a stack of 12 SW trays are manually placed on their respective infeed conveyors outside the safety enclosure. - The two safety shutters are opened, and the loaded tray stacks move into the gripper position of the respective stacker. - The safety shutters are closed again. - The respective grippers pick up the corresponding tray. - The tray is separated using the Z-axis and transported upward (above the normal pick-up height). - For centering and stabilization, a centering support is positioned beneath each tray using X-axis handling. - With the stacker's Z-axis, the respective tray is placed on the centering support. - The trays are ready for component pick-up. - With the multi-gripper on the SCARA robot, the KK is picked up from the tray and placed in an intermediate position as an alignment aid (to achieve exact pick-up positions for assembly). - The KK is scanned, picked up again, and if the scanner result is OK, mounted onto the WT. - Any KK that is not OK is placed in a reject box. - The multi-gripper on the SCARA robot then picks up the SW from the tray and places it in the alignment position. - The SW is picked up again and mounted onto the WT. - Assembly continues in the front assembly area. Gijdpfjibx S Nsx Abhsp Technical Data: Design: SCARA (4-axis robot) Nominal Load Capacity: 5 kg, Maximum: 10 kg Horizontal Reach: 850 mm Vertical Reach: Axis 3: 420 mm Orientation Range: J4: +/- 360° Repeatability (Horizontal): +/- 0.025 mm Repeatability (Vertical, J3): +/- 0.01 mm Repeatability (Orientation, J4): +/- 0.005° Maximum Working Range: Axis 1: +/- 152°, Axis 2: +/- 152.5°, Axis 3: 420 mm, Axis 4: +/- 360° Maximum Operating Speed: J1, J2: +/- 11,000 mm/s, J3: +/- 2,350 mm/s, J4: +/- 2,400°/s Permissible Inertia: nominal 0.02 kg*m², maximum 0.25 kg*m² User Wiring (electrical): 1x D-Sub 9 pin, 1x D-Sub 15 pin Z-Axis: Outer diameter: 25 mm Press-in Force: 250 N Weight: 48 kg Controller: EPSON RC180 Mounting Type: Ceiling IP Protection Class: IP20 Power and Signal Cables: 3m Financing through our bank is also possible. komplett-konzept.leasingo.de

Condition: good (used), WSM Stationary Screwing Unit Assembly and testing of components for car radios and navigation systems. The assembly station is enclosed in a protective housing. The service doors are equipped with monitoring switches with interlocks. The doors are locked during automatic operation and can only be opened during automatic stop or manually after pressing the "Doors" button on the control panel. Automatic operation cannot be started with a door open. Operational Sequence The station is loaded with the pre-assembled component via the transfer belt. The following describes the operation steps of the automatic station with a transfer belt. In normal operation, all three stations operate in parallel. - Positioning the test unit (WT) with the pre-assembled module in station 2.1 - Lowering the carrier with the scanner and vision sensor - Scanning the 3 codes (front panel, front PCB, SD PCB), comparison with the database - Checking the correct locking of the FFC in the connector - Raising the carrier and lowering the test unit onto the conveyor belt - Positioning the test unit (WT) with the pre-assembled module in station 2.2 - Positioning the screwdriver and screwing the front PCB in place - Lowering the test unit (WT) onto the conveyor belt - Positioning the test unit (WT) with the pre-assembled module in station 2.3 - Lowering the light shield and making contacts, adjusting the carrier with the test sensors from below - Type-dependent testing of the SD + CD slot lighting and buttons - Functional test of the CD eject button - Lowering the test unit (WT) onto the conveyor belt > continue Giodpfx Asibichsbhep If errors occur during testing, they are displayed on the screen. and can be repaired if possible. For this, the system is switched to manual operation and the doors are opened. After the repair and restarting the automatic system, the workpiece carrier is tested again in the station. If a repair is not possible (e.g., due to a screw error), the workpiece carrier is marked as NIO (Not Okay) in the control system and is not processed further. Manual NIO marking and rejection is also possible. Financing through our bank is also available. komplett-konzept.leasingo.de More assembly stations, new and used, can be found in our shop! International shipping costs on request!

Condition: excellent (used), Year of construction: 2014, ZIM Hülsta back wall saw Make: ZIM Hülsta-Werke Designation: Back wall saw Year of manufacture: 2014 Serial number: 380114008 Description: 2 movable Benz sawing/boring units Feed roller table Gsdpfx Absvdb Tbehoip Protective housing with Leutze laser cabinet system Switch cabinet Extraction piping Control terminal, consisting of: PC, flat screen EIZO FlexScan S1911 Keyboard and mouse, hand scanner, terminal cabinet Mobile steel tray (beige) Financing through our bank is also possible. komplett-konzept.leasingo.de Further items - new and used - can be found in our store! International shipping costs on request!

Year of construction: 2008, condition: excellent (used), Bizerba CWL Eco flex continuous scale with Sick VMS520 volume measuring system Bizerba CWL Eco flex continuous scale Dynamic weight detection with volume determination The CWL Eco flex can be integrated almost effortlessly into existing parcel shipping, sortation systems and feeding lines. Bizerba WM-CWL flex Conveyor scale Model: CWL Eco in Motion DE-09-MI006-PTB018 Gsdjmgax Ujpfx Abhsip Max 60 kg Min 0,4 kg 230 V Sick VMS520 Volume Measuring System Special features - Non-contact, active measuring method - Measurement of length, width and height of cuboid objects - Measure length, width and height of objects with almost any shape - Works with a wide range of surface structures and on various flat conveyor systems - Flexible system configurations - Calculation of the small enveloping cuboid (box volume) - Calculation of real volume Device components Sick VMD520-2000 Volume measuring device Sick CLV 490 Stationary barcode scanner Year of manufacture: 2008 Financing through our bank is also possible. komplett-konzept.leasingo.de Further articles - new and used - you will find in our store! International shipping costs on request!

Year of construction: 2023, operating hours: 10,700 h, condition: like new (used), functionality: fully functional, Build Cylinder Size: 2x 400x400x520 mm Scanning Speed: 15,2 m/s Scanner: High-precision three-axis digital galvo system Laser: CO2 Laser, 1×100W Max. Chamber Temperature: 190°C Gewicht: ca. 3.000 kg incl. 260kg FS3300 Powder incl. Chiller incl. N2 Generator incl. Breackout Station Godjn Dxbyepfx Abhoip

Condition: new, Year of construction: 2026, Comparable to: e.g. Emmegi Double mitre saw for steel Cutting length: 5,000 mm Equipped with 7 NC axes for length positioning, outward and inward saw blade inclination, saw blade feed, and saw motor speed control Torsion-free welded construction with longitudinal linear guideways 2 x saw motors, each 4.5 kW Saw blade speed: 0–250 rpm Saw feed motorized from rear to front Feed speed infinitely adjustable Motorized angle adjustment between 135° and 45° Suitable for HSS circular saw blades, Ø 400 mm Pneumatic protective covers Water cooling with pump and coolant tank Gsdoyinu Hspfx Abhoip Left saw unit fixed to the base frame, right unit motorized and traversable Positioning accuracy: ± 0.15 mm Max. traverse speed: 25 m/min Length positioning compensates for saw angles and profile height Each saw head fitted with three horizontal and vertical profile clamps; in the event of pressure loss, the horizontal cylinders remain clamped Pneumatically swivelable material support between the saw heads 15” touchscreen Single cut processing Processing of cutting lists Creation of cutting lists via keyboard Import of cutting lists via USB flash drive or network interface Corner cutting Overlength cutting Short cuts from 5 mm cutting length Crosscuts Available options: Micro-spraying unit Saw head inward inclination increased to 150° Label printer Barcode scanner Additional network interface and teleservice agreement

Condition: like new (used), Year of construction: 2022, functionality: fully functional, Prodim proliner 8XCS scanner. Includes software. Small tripod. Leaps. Backpack. IPT and hook pen and remote. Extras included - Heavy duty plastic carrying case. Extra remote. Measuring support bars. Godsyl Spaspfx Abhsip

Condition: new, Year of construction: 2026, functionality: fully functional, shaft length: 355 mm, input voltage: 230 V, type of input current: AC, laser power: 6 W, type of cooling: air, total width: 920 mm, total height: 1,760 mm, total length: 940 mm, height adjustment type: electric, scan area length: 110 mm, scan area width: 110 mm, travel distance Z-axis: 500 mm, table length: 710 mm, table width: 400 mm, laser wavelength: 355 nm, ambient temperature (min.): 15 °C, ambient temperature (max.): 35 °C, input frequency: 50 Hz, extraction nozzle diameter: 50 mm, working width: 110 mm, Equipment: cabin, UV Fiber Laser 355 nm, 6 W – NEW, SK LASER KOLLTRONIC with Workstation, Made in Germany Laser Source IPG – Made in Germany Laser Safety Class 1 Workstation: - Combined sit/stand workstation with ergonomic legroom - Fully enclosed aluminum profile construction Gjdpfxeyiz Dze Abhoip - Front door with laser protection glass for clear visibility - Bright workspace lighting - Dimensions: H 1760 × W 920 × D 940 mm - Work platform: Stainless steel plate with 25 mm hole grid (710 × 400 mm) - Rear service door, screwed for easy part loading - Motorized Z-axis: travel distance 500 mm (focus depending on lens) - Extraction nozzle DN50 (extraction optional) - Safety (PL4) - Emergency stop - Interlock with 2 standard relays - Safety relay for door monitoring UV Fiber Laser: - Wavelength: 355 nm - Power: 6 W 40 kHz - Pulse energy: 20 µJ - Pulse frequency: 10–300 kHz - Air cooled - Pilot laser red light + 2 distance lasers for focus adjustment (Laser class 2) - Laser head manually adjustable in Y-axis Scanner & Optics - F-Theta lens F = 160 mm, anti-reflective protective glass - Marking field: 110 × 110 mm Control: - Windows 11 - 19" TFT monitor, keyboard, mouse - Interfaces: RS232 / Ethernet / USB - KOLLTRONIC marking software: text, logos, QR/Data Matrix, barcodes Operation: - 230 V / 50 Hz - 15–35 °C Condition: - New machine - CE compliant · Made in Germany

Condition: ready for operation (used), Year of construction: 2012, Laser power: 4000W (4kW), wavelength: 1030nm, beam quality (BPP): 8mm/mrad, beam diameter setting: 0.1µm, machine dimensions X/Y/Z: approx. 1000mm/1600mm/1600mm, weight: approx. 1000kg. Including 2x scanner optics (PFO) for the process cells, 3x fiber optic cables and spare parts. Documentation available. On-site inspection is possible. Giodpfswwll Hex Abhop

Condition: ready for operation (used), Year of construction: 2020, A thickness measuring device Scantech is available. Measuring frame width: 2500mm, sensor power: 5keV-15keV, max. web width: 2100mm, max. web speed: 200m/min, product tolerance at 57µm-63µm: +/-5%, measuring accuracy at 60µm: +/-0.3µm, max. ambient temperature: 45°C, orientation: Left-B. Machine dimensions X/Y/Z: approx. 3250mm/300mm/900mm, weight: approx. 400kg, control: Flexscan 6, interface: OPC-UA. Components: scanner, HMI, IO box, and various small parts. Documentation available. An on-site inspection is possible. Giedjw R Dg Iopfx Abhjp

Condition: ready for operation (used), Year of construction: 2019, A complete can erecting, counting and seaming system including labeling and cartoning is available. 1) Can unscrambler IMA Swiftpack UN 800S, year of manufacture: 2007, unscrambling capacity: 60 cans/min, formats diameter/height: 45mm/51.5mm, 45mm/84mm, 45mm/96mm, 60mm/80mm, 60mm/122mm. 2) Counting machine Cremer CF 1220, year of construction: 2002, counting capacity: 1000 products/min, counting heads: 1, channels: 12, formats: Capsules (HGK & WGK) and tablets (round & oblong), including one cylinder for storage flaps as spare part. 3) 2x rotary plate Höflinger & Karg S1, plate diameter: 1000mm. 4) CBV Servo lid closing machine (screw capper), year of manufacture: 2019, closing capacity: 40 closing operations/min, lid diameter range: 23mm-100mm. 5) Rudolf Deckert AVM 738 can seamer (crimper), year of manufacture: 2003, seaming capacity: 50 cans/min, can diameter: 45mm/60mm, lid formats diameter/height: 42.4mm/17.15mm, 50mm/12mm. 6) Can and bottle labeler IMA Sensitive 350, year of construction: 2009, labeling capacity: 350 labels/min, can and bottle diameter range: 15mm-78mm, max. product height: 220mm, label length range: 15mm-220mm, label height range: 10mm-140mm, equipped with hot stamping Allen Coding Set S-Compact 50/30 and camera Keyence IV 500 CA. 7) Can and bottle cartoner Uhlmann C100, year of construction: 1988, cartoning capacity: 70 cans/min, max. Can/bottle diameter and height: 60mm/120mm, folding carton length range: 30mm-113mm, folding carton width range: 15mm-85mm, folding carton height range: 70mm-130mm, the machine was converted to cans and bottles in 2017 and equipped with a Mitsubishi D700-SC control system, including GUK Cartonac 91 folder, 3x code reader and luminescence control. 8) Wipotec TQS-HC-A coding and inspection device for serialization, temper evident and weighing, year of manufacture: 2017, inspection capacity: 300 products/min, including 2x Herma 400 label dispenser, dual print head (2 cartridges), camera for print inspection, load cell with weighing belt and hand scanner. 9) Christ FilmTeq 3030 banding machine, year of manufacture: 2011, infeed capacity: 50-200 folding boxes/min, outfeed capacity: 7-50 packs/min, folding box length range: 15mm-400mm, folding box width range: 15mm-90mm, folding box height range: 60mm-150mm, bundle length range: 60mm-400mm, bundle width range: 60mm-150mm, bundle height range: 30mm-230mm. Documentation available. On-site inspection is possible. Giedpfx Aswa Tixebhjp

Condition: ready for operation (used), Year of construction: 2023, Usable working area: 2000x3000mm, z-axis: 50mm, repeatability on the entire surface: ±0.05mm, X/Y/Z-addressable resolution: 0.001mm, max. acceleration: 15m/s², max. working speed in XY-axis: 2000mm/s, drives: X/Y-system with linear motors, Z-axis with servo motor. Laser protection class: Class 1, with cover, base body: stable, welded steel frame structure, axis system: X/ Y/ Z movement axes, drive: linear motor drive, contactless and low-wear, removal system: 2000mm extension, conveyor: Aluminum slats with servo motor drive, Pressure roller: for material, Laser source: CO2 laser 300W, closed and maintenance-free, Cooling: Closed cooling circuit with water recooler for laser, Cutting head: 5 inch, lens, cutting nozzle, cutting gas supply, Extraction: Extraction tray for small parts and dust, Software: CAM control software ICARO. Motorized brush width: 2000mm, SEI PC console: without computer, to be provided by the customer, Extraction unit: 2x extraction fans 5.5kW each, Scanner: Manual barcode scanner, Unwinding device: for material rolls with unwinding bar, Unwinding system: Connection available. The system was only installed and approved, series operation did not take place. On-site inspection is possible, documentation available. Gjdpfx Aowbuzfsbhjip

Year of construction: 2012, condition: ready for operation (used), A glass processing plant with several production lines is available. 1) Cutting line with automatic breaking system 2) Cutting line with automatic breaking system 3) Glass scrap disposal line 4) Glass scrap disposal line 5) Double-sided glass grinding and washing machine Scheppach 2500 C4/0E with washing machine T 4516 133 6) Double-sided glass grinding and washing machine Scheppach 2500 C4/0E with washing machine T 4516 133 and portal drilling machine, max. glass dimensions: 2600x2200mm 7) Control system 8) Water supply system for washing machines with circulation water treatment, sludge dewatering, chemical supply, and additional components 9) Horizontal tempering furnace Tamglass ProE-2442-ABS-20 10) Domino D550+ 10 (55W and 10mm scanner). A large number of spare parts, complete spare robots, and numerous glass racks in various formats are also available for purchase. Complete documentation available. On-site inspection is possible. Gijdpfx Asxcx A Tsbhep

Condition: excellent (used), Year of construction: 2009, Weeke BHX 500 – Operator Side Right Weeke Machining Center, each with one machining support above and below Infeed table with automatic workpiece feeding and positioning WORKPIECE DIMENSIONS Gjdpfsx S Hzlex Abhjip Min. workpiece length: 200 mm Max. workpiece length: 2,500 mm Min. workpiece width: 70 mm Max. workpiece width: 1,000 mm Min. workpiece thickness: 8 mm (2*4 mm) Max. workpiece thickness: 80 mm Max. workpiece stacking: 2 pieces Machine configuration: 2V21 HIGH SPEED 7500 Vertical drilling unit arranged in both upper and lower machining supports, each with 21 drilling spindles (individually controllable with variable speed range). 2H4X/1Y Horizontal drilling unit arranged in both upper and lower machining supports, each with 10 spindles individually selectable via program. Each with 8 drilling spindles: in X-direction Each with 2 drilling spindles: in Y-direction N2 X-Y 90° Grooving saw unit arranged in both upper and lower machining supports for machining operations in the X-Y direction, swiveling 90°. Cutting depth: 30 mm ADDITIONAL NOTE ON GROOVING SAW BLADE The saw blade width can be 8.4 mm. The cutting cross-section must not exceed 70 mm². F2-ETP-6 KW Milling unit arranged in both upper and lower machining supports, suitable for receiving shank tools. Manual tool change. Tool clamping: manual, Hydro quick-clamping system ETP 25 Rotation direction: right/left Speed: 6,000 – 18,000 rpm, stepless programmable Machining up to 3,000 mm Infeed table with automatic workpiece feeding and positioning Workpiece discharge area with cross belt conveyor and lifting arms – Workpiece length measurement in the machine – Movable operator terminal – Barcode software incl. scanner

Year of construction: 2013, condition: good (used), BHT INNOVA E3 Professional Bronchoscope Washer INNOVA – Professional Endoscope Washer for Practices and Small Clinics Gedpfx Asin Edwobheip The INNOVA™ E3s is the world's best-selling BHT endoscope washer. This endoscope washer is compact and offers a high capacity for endoscopes or bronchoscopes. Depending on the reprocessing, a total of 10 to 20 endoscope reprocessings are possible daily. This makes it the perfect solution for private medical practices and small clinics that value safe hygiene, efficiency, and reliability. Reliability and maximum cleanliness in every cycle: Compliant with DIN EN ISO 15883-1/-4 and the guidelines of the Robert Koch Institute (RKI), and with many additional functions, e.g., thermal self-disinfection at 90°C according to DIN EN ISO 15883-4, 4.8.1. - Flexible in combination with another INNOVA® E2 or E3 for 30 to 40 reprocessings daily. - Suitable for both glutaraldehyde and peracetic acid from a wide range of suppliers. - Suitable for commercially available endoscopes from Fuji, Olympus, Pentax, Storz, and Wolf. - Single-channel connection or patented pressure chamber available. - Thermal reprocessing option, e.g., for multiple biopsy forceps, polyp loops, etc. - Thermal disinfection of the final rinse water as recommended by the Robert Koch Institute (RKI) for the DH version. - Secure documentation and traceability through batch control. User and endoscope identification via barcode scanner. - Data output via printer, data logger, or computer interface. Easy integration into existing IT systems Number of endoscopes: For 2 endoscopes or 4 ENTs Hygienic design: Hygienic workflow, single-door Channel connection system: Single-channel connection or patented pressure chamber system possible Single-channel monitoring system (CMS): No Chemistry Glutaraldehyde / Peracetic Acid: Both possible: DH version (with boiler, for glutaraldehyde) or DC (filter solution, for glutaraldehyde or peracetic acid) Documentation and integration: Yes, interface for printer/data logger as standard. Printer as standard. Optional scanner/IT interface Thermal reprocessing of instruments at 90°C: Available with additional equipment Electrical installation: 3-phase 400 V / 50 Hz AC+N+PE. Connected load: 11 kW. Fuse rating: 3 x 20 A Year of manufacture: January 19, 2013 Item condition: used Financing through our bank is also possible. komplett-konzept.leasingo.de Find more items - new and used - in our shop! International shipping costs on request!

Condition: excellent (used), Year of construction: 2024, functionality: fully functional, Safety tester with scanner for high-voltage test station - EATON Sefelec 506-S Gsdpfxexqxw Tj Abhsip - EATON Sefelec 64-SC The devices were purchased in 2023/2024 and are in top condition. The SEFELEC 506-S test device for electrical safety testing, an EATON next-generation model, is based on ARM dual-core technology components and is controlled via DSP. This technology offers the operator optimal stability and repeatability of measurements. The high accuracy and measurement speed are tailored to the requirements of quality assurance in production and incoming goods inspection. The sequence function facilitates the operation of the SEFELEC 506-S test station when integrated into a test stand or test bench. The 7” touchscreen of the new SEFELEC model series impresses with simple and intuitive operation. - Standard interfaces: Ethernet / RS232 / USB / PLC - Optional: IEEE488-2 interface - Dual safety circuit SIL2 - Automatic selection of test series - Sequence mode for combining multiple consecutive tests Voltage withstand at 5kVAC 500VA and 6kVDC Detection modes by current threshold or current fluctuations (ΔI) Burn function mode without current detection Megohmmeter 200 GΩ, test voltage from 20 VDC to 1000 VDC Optional: 2TΩ range PE measurement at 32A - 8VAC, measurement 0 ... 1Ω Optional: test current 50A Programmable test ramps Ramp up, hold, ramp down Multi-ramp mode, up to 7 steps TFT touchscreen 7”, 16 million colors, for programming, as well as for displaying ongoing tests and results Integrated ARM dual core control & Nand 3D technology for optimal accuracy, stability and repeatability Integrated DSP enables higher test speeds Large internal memory for storing configurations and test results Completely compliant with IEC 61010-2-034 (safety requirements for test and measurement equipment for insulation resistance measurement and equipment for voltage withstand testing) Shipping is possible subject to prior agreement. #8312-2

Condition: good (used), Year of construction: 2006, operating hours: 20,000 h, Trumpf Haas HL 4006D YAG Solid-State Laser The Trumpf Haas HL 4006D is a 4000W Nd:YAG solid-state laser designed for industrial applications such as welding highly reflective materials, especially for use with robots and with a range of up to 100 meters via flexible fiber optics. Areas of Application Welding: The main application is welding metal parts, especially highly reflective materials such as aluminum and copper, where other lasers are difficult to use. Automated Manufacturing: The laser is designed for integration into automated production lines with industrial robots. Precision Machining: The high power and precise beam quality enable precise work in industrial machining. Technical Specifications Manufacturer: Trumpf Haas Type: HL 4006D Nominal laser power: 4000 W Gsdpjxg Hpcsfx Abhsip Beam quality: 25 mm.mrad Laser light wavelength: 1064 nm Nominal voltage: 400 V Nominal power: 132 kW Nominal power consumption: 140 kVA Year of manufacture: Oct 2006 Weight: 1500 kg Operating hours: approx. 20,000 Dimensions (W x H x D): 3200 x 1700 x 1250 mm Laser optics including ILV scanner, pyrometer, and various spare parts Computer with WinLas software for parameter control You can find the right cooling unit and robot in our shop Rehsler TW HL4006D Cooling Unit Kuka KR 30/2 6-Axis Welding Robot Financing through our bank is also possible. komplett-konzept.leasingo.de Other items - new and Used - find it in our shop! International shipping costs on request!