Used Section Bender for sale (3,164)

Condition: used, Year of construction: 1976, round bar steel 28 mm square edge steel 25 mm L-beam 80 x 8 mm notching cap. mild steel max. 7 mm cutting capacity of the vertical shear 350 kN Cedpewm Rmnjfx Abtshb Punch power 190 kN shear: flat material 100 x 11 mm shear: length of knifes ca. 175 mm total power requirement 1,5 kW weight of the machine ca. 0,5 t dimensions of machine L x W x H 1,0 x 0,5 x 1,5 m

Condition: used, Year of construction: 1983, round bar steel 50 mm square edge steel 40 x 40 mm L-beam 140 x 13 mm Punch power 900 kN hole punching press: throat 510 mm hole punching press: max. length of stroke 29 mm Chjdjvh I T Njpfx Abtob hole punching press: capacity (dia. x thick.) 31 x 20 mm notching: l + T material 80 x 14 mm no. of strokes 40 / 45 Hub/min total power requirement 4 kW weight of the machine ca. 3,7 t dimensions 2,1 x 0,7 x 2,12 m Accessories: various punches and dies

Condition: new, 45 to. no. of strokes 24 Hub/min hole diameter in sheet thickness max. Ø 27 in 13 mm 80x80x8 60x60x6 mm flat steel 300x10/200x13 mm 7 mm Cjdpfx Abeyv N Ayjtjhb engine output 2.2 kW range L-W-H 1550x820x1540 mm weight 760 kg Standard equipment: - Complete knife set for flat steel shears - complete knife set for angle steel shears - complete standard punching equipment - Stamp quick release device for punches up to Ø 27 mm - Rectangular notching device complete with hold-down device - notch - Support table for punching device

Condition: new, flat steel 350 x 15 mm round bar steel 35 mm square edge steel 30 mm L-beam 80x80x8 mm Chedpsyv Nafofx Abteb hole diameter in sheet thickness Ø 27 in 13 / Ø 20 in 18 mm blade length 356 mm engine output 3.0 kW Stroke rate 34 Punching capacity max. 500 kN weight 950 kg dimensions 1300x1100x1850 mm Standard equipment: - Knife set for flat steel - Complete knife set for angle steel shears - Complete normal punching equipment - Quick release device for punches up to 31 mm - Support table for punching device, rectangular notching and flat steel shears - Bending stamp with matrices V 40 and V 70 - Electric contact stop (1.000 mm)

Condition: new, neu ca. 8 Wochen ab Auftragse Spanien 36000 € 687.6 € 85 to 500 mm 5 40/15 bzw. 24x24 mm 450x15 / 450x18 mm 475 mm 130x130x13 mm 45/40 mm 12 mm 200x12 mm 9.2 kW 2300 mm 1200 mm 2100 mm Chodpjwirk Tjfx Abtob 2400 kg hydraulic drive 2 foot pedals for independant working on punching and section station bending unit with 2 dies, V40 and V70 flat steel stationWITH DEVICE FOR REDUCING DEFORMATION angle iron station with round and square bar cutting hydraulic downhold for flat- and angle station triangular notching station with table and gauge punching station with table and gauge gauge 1000 mm with contact switch, for angle / flat steel station operating manual in German and Englisch

Condition: new, neu ca. 8 Wochen ab Auftragse Spanien 25700 € 490.87 € 80 to 500 mm Cjdpfewirrwex Abtjhb 5 40/14 bzw. 24/24 mm 70 mm 40 1/min 450x15 / 300x20 mm 130x130x13 mm 45 mm 12x52x90 mm 9 kW 2310 mm 1200 mm 2050 mm 2400 kg 2 foot pedals for independent work at 2 stations hydr. drive flat bar shear angle bar shear with minimum deformation by diagonal moving of the blade round and square bar shear rectangular notching unit punching unit up to diam. 40 mm fast hydraulic, centring device oilfilling table at the punching station with gauge table at the notching unit with gauge table at the flat bar shear user manual in GERMAN and ENGLISH OPTION: Kit € 970,00 length stop 1000 mm with contact switch, for angle, flat or bar station magnetic machine lamp 10 set round punches and dies: 8, 10, 12, 14, 16, 18, 20, 22, 24 and 26 mm

Condition: new, neu ca. 10 Wochen ab Auftrags Spanien 72800 € 1375.92 € 165 to 610 mm Chedpfeynmq Rjx Abteb 5 40/30 bzw. 34/34 mm 110 mm 31 1/min 750x20 / 400x30 mm 205x205x18 mm 60 mm 16x58x110 mm 15 kW 2950 mm 1600 mm 2200 mm 6300 kg 2 foot pedals for independent work at 2 stations hydr. drive flat bar shear angle bar shear with minimum deformation by diagonal moving of the blade round and square bar shear rectangular notching unit punching unit up to diam. 40 mm fast hydraulic, centring device oilfilling table at the punching station with gauge table at the notching unit with gauge table at the flat bar shear user manual in GERMAN and ENGLISH (sample photos) OPTION "KIT" € 970,-- length stop 1000 mm with contact switch, for angle, flat or bar station magnetic machine lamp 10 set round punches and dies: 8, 10, 12, 14, 16, 18, 20, 22, 24 and 26 mm Further available models of HYD 165 series: model S € 55.200,-- as model SD but 510 mm gap weight 5.200 kg (sample photos) WE HAVE MORE THAN 700 REFERENCES!

Condition: new, neu ca. 10 Wochen ab Auftrags Spanien 35600 € 679.96 € 110 to 610 mm 5 40/20 bzw. 28/28 mm 80 mm 28 1/min 600x15 / 400x20 mm 152x152x13 mm 50 mm 13x52x90 mm 9 kW 2690 mm 1400 mm 2200 mm 3300 kg 2 foot pedals for independent work at 2 stations hydr. drive flat bar shear angle bar shear with minimum deformation by diagonal moving of the blade round and square bar shear rectangular notching unit Csdpfx Abjynmrbjtshb punching unit up to diam. 40 mm fast hydraulic, centring device oilfilling table at the punching station with gauge table at the notching unit with gauge table at the flat bar shear user manual in GERMAN and ENGLISH OPTION: Kit € 970,00 length stop 1000 mm with contact switch, for angle, flat or bar station magnetic machine lamp 10 set round punches and dies: 8, 10, 12, 14, 16, 18, 20, 22, 24 and 26 mm

Condition: new, neu ca. 8 Wochen ab Auftragse Spanien 30800 € 588.28 € 85 to 300 mm Chodpfxjwiqtge Abtob 5 40/15 bzw. 24x24 mm 450x15 / 450x18 mm 475 mm 130x130x13 mm 45/40 mm 12 mm 200x12 mm 9.2 kW 2300 mm 1200 mm 2100 mm 2400 kg hydraulic drive 2 foot pedals for independant working on punching and section station bending unit with 2 dies, V40 and V70 flat steel stationWITH DEVICE FOR REDUCING DEFORMATION angle iron station with round and square bar cutting triangular notching station with table and gauge punching station with table and gauge gauge 1000 mm with contact switch, for angle / flat steel station operating manual in German and Englisch

Condition: new, neu ca. 8 Wochen ab Auftragse Spanien 19600 € 376.32 € 55 to 500 mm Cjdjwirgbopfx Abtehb 5 40/10 bzw. 20/20 mm 20 mm 37 1/min 300x15 / 200x20 mm 10x42x90 mm 5 kW 2100 mm 1160 mm 2090 mm 1750 kg 2 foot pedals for independent work at 2 stations hydr. drive flat bar shear angle bar shear with minimum deformation by diagonal moving of the blade round and square bar shear rectangular notching unit punching unit up to diam. 40 mm fast hydraulic, Ankörnvorrichtung oilfilling table at the punching station with gauge table at the notching unit with gauge table at the flat bar shear user manual in GERMAN and ENGLISH OPTION: Kit € 970,00 length stop 1000 mm with contact switch, for angle, flat or bar station magnetic machine lamp 10 set round punches and dies: 8, 10, 12, 14, 16, 18, 20, 22, 24 and 26 mm

Condition: new, neu ca. 8 Wochen ab Auftragse Spanien 22400 € 430.08 € 80 to 300 mm 5 40/14 bzw. 24/24 mm 70 mm 40 1/min 450x15 / 300x20 mm Codpfxewirr Do Abtohb 130x130x13 mm 45 mm 12x52x90 mm 9 kW 2310 mm 1200 mm 2050 mm 2070 kg 2 foot pedals for independent work at 2 stations hydr. drive flat bar shear angle bar shear with minimum deformation by diagonal moving of the blade round and square bar shear rectangular notching unit punching unit up to diam. 40 mm standard hydraulic, centring device oilfilling table at the punching station with gauge table at the notching unit with gauge table at the flat bar shear user manual in GERMAN and ENGLISH (sample photo shows mod. hyd 80 SD) option "Kit" EURO 970,-- length stop 1000 mm with contact switch, for angle, flat or bar station magnetic machine lamp 10 set round punches and dies: 8, 10, 12, 14, 16, 18, 20, 22, 24 and 26 mm Further available models of HYD 80 series: model SD EURO 25.700,-- as model S but 500 mm gap weight 2.400 kg WE HAVE MORE THAN 700 REFERENCES!

Condition: new, Year of construction: 2025, neu 2025 090054 prompt, Zwischenverkauf v Spanien 17300 € 298.94 € 1 15570 € 55 to 250 mm 5 40/10 mm 20 mm 37 1/min 300x15 mm 120x10 mm 40 mm 10 mm 5 kW 1670 mm 1160 mm 2090 mm 1390 kg Chodpfx Aswirxwebtjb 2 foot pedal for independent working on 2 stations flatsteel station anglesteel station round- and square steel station rectangular notching station punching station table on flat steel station table on punching station table on notching station complete with hydraulic oil user manual in GERMAN and ENGLISH OPTION: Kit € 930,00 length stop 1000 mm with contact switch, for angle, flat or bar station magnetic machine lamp 10 set round punches and dies: 8, 10, 12, 14, 16, 18, 20, 22, 24 and 26 mm

Condition: new, neu ca. 8 Wochen ab Auftragse Spanien 24800 € 476.16 € 60 to 500 mm 5 2 40x11 mm 32 1/min 350x10 mm 120x10 mm 45/40 mm 100x10 mm 150x10 mm 5.5 kW 2100 mm 1400 mm 2060 mm 1750 kg 5 workstations foot pedal trigger hydr. drive flat steel shears incl. Device for reducing the deformation Chjdpfewiq Evox Abtob angle iron scissors with round and square bar opening triangle claw punching and bending device for flat iron table at the flat steel and notching station user manual in GERMAN and ENGLISH

Condition: new, neu ca. 8 Wochen ab Auftragse Spanien 49600 € 947.36 € 130 to 600 mm Chodpfxjynnggj Abtob 5 2 50x18 mm 80 mm 600x18 (max. 600x20 mit D mm 120x120x11 (max. 150x150x mm 45/40 mm 130x12 mm 250x12 mm 15 kW hydraulic drive 2 foot pedals for independant working on punching and section station bending unit with 2 dies, V50 and V90 flat steel stationWITH DEVICE FOR REDUCING DEFORMATION angle iron station with round and square bar cutting triangular notching station with table and gauge punching station with table and gauge gauge 1000 mm with contact switch, for angle / flat steel station operating manual in German and Englisch

Condition: new, Year of construction: 2026, functionality: fully functional, Servo PANEL BENDER FBC 2516 Chsdpjyvzq Asfx Abtjb CNC sheet metal bending machines offer high flexibility, efficiency, precision, and a high level of automation. They are suitable for processing enclosures, doors, and other components. These machines are widely used in sectors such as kitchen appliances, control cabinets, power electronics, elevators, and more. Technical specifications: - Automatic tool change - Bending length: 2500 mm - Maximum sheet width: 1500 mm - Maximum diagonal length: 2800 mm - Maximum bending height: 165 mm - Maximum material thickness: stainless steel 1.2 mm / aluminum 3 mm / mild steel 2 mm - Minimum sheet thickness: 0.35 mm - Possible bending angles: 0°-180° - Inside radius: 0.8–1.2 mm - Dimensions: 5.4 m x 4 m x 2.9 m - Weight: 19,500 kg - Control: Beckhoff This machine will be exhibited at Euroblech 2026 in Hannover and will be available from October. We have been distributing YAWEI machines throughout Europe for over 20 years. Service and spare parts supply by H+S – everything from a single source.

Year of construction: 2018, condition: good (used), Make: FACCIN Type: 4HEL 3590 Control: Siemens TOUCH Year: 2018 Specifications Metric US Standard Rolling width 3500 mm Rolling thickness 3x toproll Ø 80 mm Rolling thickness 5x toproll Ø 110 mm Rolling thickness prebending 90 mm Top Roll Ø 900 mm Top Roll Ø 900 mm Bottom Roll Ø 800 mm Side roll Ø 600 mm Number of rolls 4 Rolling speed 0-6 Adjustiment lower roll 0-200 mm/min. Adjustment side rolls 0-400 mm/min. Cedpfekvm Nfox Abtehb Top support yes Side supports yes Number of driven rolls 2 Power 90+75+9 kW Dimensions (Estimate) Length 4430 mm Width 8800 mm Height 11000 mm Weight 178000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1980, condition: good (used), Make: HAEUSLER Type: VRM-HY Year: 1980 Specifications Metric US Standard Rolling width 3000 mm Rolling thickness 3x toproll Ø 130 mm Rolling thickness 5x toproll Ø 140 mm Rolling thickness prebending 120 mm Top Roll Ø 950 mm Bottom Roll Ø 850 mm Side roll Ø 180 mm Number of rolls 4 Rolling speed 2 + 4 Adjustiment lower roll 0 - 400 mm/min. Adjustment side rolls 0 - 400 mm/min. Number of driven rolls 2 Cjdpfxskvm Szj Abtohb Power 132 + 37 kW Dimensions (Estimate) Length 12000 mm Width 5440 mm Height 5650 mm Weight 286000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1978, condition: good (used), Make: HAEUSLER Type: VRM-HY Year: 1978 Specifications Metric US Standard Rolling width 3050 mm Rolling thickness 3x toproll Ø 60 mm Rolling thickness 5x toproll Ø 70 mm Rolling thickness prebending 50 mm Top Roll Ø 630 mm Bottom Roll Ø 600 mm Side roll Ø 500 mm Number of rolls 4 Rolling speed 0 - 5 Adjustiment lower roll 200 mm/min. Adjustment side rolls 200 mm/min. Number of driven rolls 2 Power 120 kW Dimensions (Estimate) Length 5790 mm Width 4200 mm Height 4200 mm Weight 85000 kg Chedpfx Abjkvm S Njtob Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1991, condition: good (used), Make: HAEUSLER Type: VRM-HY Year: 1991 Specifications Metric US Standard Rolling width 3000 mm Rolling thickness 3x toproll Ø 120 mm Rolling thickness 5x toproll Ø 150 mm Rolling thickness prebending 100 mm Top Roll Ø 910 + 820 + 740 mm Bottom Roll Ø 940 mm Side roll Ø 780 mm Number of rolls 4 Rolling speed 2 + 4 Adjustiment lower roll 200 mm/min. Adjustment side rolls 500 mm/min. Number of driven rolls 2 Cjdpfx Askwcc Njbtohb Power 300 kW Dimensions (Estimate) Length 8000 mm Width 5400 mm Height 5400 mm Weight 290000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details! Share on

Condition: excellent (used), Year of construction: 1997, number of rollers: 4, roller (bottom) diameter: 280 mm, roller (top) diameter: 200 mm, side roll diameter: 280 mm, roller length: 3,000 mm, sheet thickness (max.): 6 mm, overall weight: 7,250 kg, total length: 6,000 mm, total width: 2,000 mm, total height: 2,000 mm, power: 6 kW (8.16 HP), 4 roll plate bender HAEUSLER - VRM-HY MACH-ID 9604 Make: HAEUSLER Chedpfoy Expusx Abtsb Type: VRM-HY Control: HAEUSLER CNC Rolling width: 3000mm Rolling thickness 3x toproll Ø:4mm Rolling thickness 5x toproll Ø:6mm Rolling thickness prebending: 3mm Top Roll Ø: 200mm Bottom Roll Ø: 280mm Side roll Ø: 280mm Number of rolls: 4 Rolling speed: 0-5 Adjustiment lower roll: 0-200mm/min. Adjustment side rolls: 0-200mm/min. Number of driven rolls: 2 Power: 6kW Length: 6000mm Width: 2000mm Height: 2000mm Weight: 7250kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: new, Oil tank capacity: 12Bending capacity: (Flaches Material) 200 x 12Bending capacity: (Runde Rohre) 48 x 4,0pressure: 20working speed: 10Return speed: 10motor: 2.2table area: 480 x 1060working height: 930length: 1150width: 480heigth: 1200stroke: 185weight approx.: 530 UZMA hydraulic horizontal presses with multi-directional feature, pipe, flat bar, profiles, bars, such as all kinds of materials allows us to perform a large number of different operations such as bending, punching, straightening etc. With the fast die changing system, you can quickly bend materials like sheet, pipe, profile and rod with suitable molds without wasting time. Versatile operation feature and easy usage makes UZMA horizontal press machine an essential machine for metalworking shops Standard Accessories: - Steel frame & robust machine design  - Stroke adjustment by digital read out  - Manual or automatic working system  - Easy to change the die by quick change  Codpfer I H A Aex Abtjhb - Durable construction of tools and tool guides made of high quality and hardened steel  - Foot pedal with digital display and emergency stop switch  - 1 set of pressbrake tooling

Condition: new, Shaft diameter: 480working speed: 3-6motor power: 22length: 2500width: 2200heigth: 2300weight approx.: 9300 Technical specifications: - Steel construction welded frame - 3 Rolls are powered - Hardened and ground shafts made of high tensile special steel - Rolls are hardened and ground - Horizontal working position - Hardened standard rolls - Mobile control panel - 3 Axis mechanical lateral angle guide rolls - Brake motor equipped for the precision bending - Digital Read-Outs (2pcs) Options: - Digital Readout STANDARD - NC Unit 10 Screen  EURO 11.500,-- Codoh Alh Repfx Abtjhb

Condition: new, Shaft diameter: 315working speed: 7motor power: 7,5length: 2000width: 1450heigth: 1700weight approx.: 3650 Technical specifications: - Steel construction welded frame - 3 Rolls are powered - Hardened and ground shafts made of high tensile special steel - Rolls are hardened and ground - Horizontal and vertical working position - Hardened standard rolls - Mobile control panel - 3 Axis mechanical lateral angle guide rolls - Brake motor equipped for the precision bending Chsdoh Alicepfx Abtsb - Digital Read-Outs (2pcs) Options: - Digital Readout STANDARD - NC Unit 7 Screen EURO 9.000,--

Condition: new, Shaft diameter: 50roll diameter: 155working speed: 4,5motor power: 1,5length: 750width: 1000heigth: 1400weight approx.: 400 Technical specifications: - Steel frame - Two rolls direct driven by a gear system - Rolls are hardened - Rolls shafts are special steel material hardened and ground - Roll shafts housed by bearings - Standard rolls - Guide rolls - Horizontal and vertical working position Options: - Digital Readout EURO 600,-- - Angle Lateral Guide Rolls EURO 900,-- - Double Speed Working   EURO 600,--                                                                                                                                                                                                                                                                                                                                                                                                                                                                                   PK 35 file TypeSizeMin. DiaNotes160x10         40x10500         400Standard Rolls2100x15         60x10450         350Standard Rolls335x35         20x20900         300Standard Rolls4Ø 35         Ø 30600         400Optional Rolls5Ø 70x2         Ø 30x21000         500Optional Rolls62”x2,9         1”x2,31000         350Optional Rolls7 70x30x2         50x40x31200         1200Optional Rolls8 50x3         40x31700         600Optional Rolls9 50x50x5         40x40x5800         600Optional Rolls1050x50x6         30x30x31000         500Optional Rolls1160x7         30x4 700         400Standard Rolls1260x7         30x4800         500Standard Rolls1360x7         30x4 700         500 Standard Rolls14UPN 80         UPN 301000         500Optional Rolls*15UPN 80         UPN 301200         800Standard Rolls* Chjdpfx Abjd Eqqwetsb         * Special washer (spacer) can be necessary / Only with special Beam Bending Attachment         •Capacities are given for 260 N/mm² plate yielding strength          

Condition: new, Shaft diameter: 30Upper Roll Diameter: 148Bottom Roll Diameter: 118working speed: 2-4motor power: 0,7 - 0,85length: 600width: 800weight approx.: 220heigth: 1450 Technical specifications: - Steel frame - Two bottom rolls are powered - Direct drive power system with gears - Top roll is idle ( free turning ) - Hardened rolls - Rolls shafts are special steel material hardened and ground - Double speed motor - Standard rolls - Adjustable guide rolls - Horizontal and vertical working position Options: - Digital Readout EURO 600,-- Chedpfsd Eqqzox Abtob - Angle Lateral Guide Rolls EURO 900,-- - Double Speed Working STANDARD - Brake Motor Option EURO 150,--                                                                                                                                                                                                                                                                                                                                                                                                                PK 30 file TypeSizeMin. DiaNotes150x10        20x61800        300Standard Rolls280x15        30x6700        400Standard Rolls330x30        10x10900        200Standard Rolls4Ø 30        Ø 10900        200Optional Rolls5Ø 60x1,5        Ø 25x1,51000        600Optional Rolls61 1/2”x2,9        1/4”x1,8600        300Optional Rolls750x30x3        40x20x21200        800Optional Rolls840x3        30x21200        800Optional Rolls940x40x5        30x30x4600        300Optional Rolls1035x35x5        30x30x4600        400Optional Rolls1150x6        20x3600        400Standard Rolls1250x6        20x3600        400Standard Rolls1350x6        20x3600        400Standard Rolls         * Special washer (spacer) can be necessary / Only with special Beam Bending Attachment        •Capacities are given for 260 N/mm² plate yielding strength