Used Section Bender for sale (3,191)

Condition: ready for operation (used), functionality: fully functional, Equipment: foot remote control, Geka Hydrocrop Hydraulic Ironworker Model: 70 S Angle (90 Degrees):130 x 130 x 13mm Flat: 450 x 15mm Fgodpfx Aiozux N Revog Round: 45mm Square:45mm Punching: 28 Dia Through 20mm Dimensions: 2000 x 1200 x 2000mm High Weight: 1800 Kgs

Condition: used, Year of construction: 1990, Gebruikte ponsmachine van Kingsland Type: 55 P 625 Fgjdpeyu Sqisfx Aivsg Capaciteit: 55 ton Keeldiepte: 625 mm Bouwjaar: 1990

Condition: excellent (used), Year of construction: 1988, control type: NC control, actuation type: hydraulic, number of rollers: 4, roller (bottom) diameter: 370 mm, roller (top) diameter: 370 mm, side roll diameter: 280 mm, sheet thickness (max.): 20 mm, overall weight: 13,500 kg, total length: 6,900 mm, total width: 2,100 mm, total height: 2,100 mm, New ( 2026) Digital read out position side rolls Hydraulic drop end Minimum bending diameter 420 mm Full hydraulic machine Roll quality C60 900N/mm2 Rolling width: 3100mm Rolling thickness 3x toproll Ø:15mm Rolling thickness 5x toproll Ø:20mm Rolling thickness prebending: 12mm Top Roll Ø: 370mm Bottom Roll Ø: 370mm Side roll Ø: 280mm Number of rolls: 4 Rolling speed: 0 - 4 Adjustiment lower roll: 0 - 700mm/min. Adjustment side rolls: 0 - 200mm/min. Number of driven rolls: 2 Power: 15kW Length: 6900mm Width: 2100mm Fjdezxxgwspfx Aivegg Height: 2100mm Weight: 13500kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 1985, round bar steel 45 mm square edge steel 40 mm L-beam 120 x 13 mm flat steel 500 x 12 mm punching pressure 60 t throat 510 mm 500 x 12 oder 400 x 16 mm punch diameter 27 in 17 mm punch diameter 39 in 12 mm Fgjdpfx Aiovg R Rzeveg oil volume 80 l total power requirement 7,5 kW weight of the machine ca. 2,4 t dimensions of the machine ca. 1,8 x 0,9 x 1,8 m Hydraulic machine with 5 stations so punching, notching, shearing flat iron, angle iron, solid material, punching with hand lever, profile steel side with foot switch. Punching discharge: 510 mm! All performance data refer to a material strength of 450 N / mm². Electric 380 volt

Condition: excellent (used), Year of construction: 1967, operating hours: 4,336 h, I sell a decent massive pipe bender in very good condition Weight of the bender 4.5T+ about 1T wheels to work. Fedpfx Aoudlymeivsgg

Condition: like new (used), functionality: fully functional, Year of construction: 2025, TECHNICAL SPECIFICATIONS • Punching force: 850KN / 85 tons • Punching: Ø40x15mm • Cuts per minute (stroke 20mm): 40 Fgodpfx Aszg Dxbeivjg • Throat depth: 500mm • Stroke: 70mm • Cutting of L-shaped profiles at 90º: 120x120x10mm • Flat bars: 450x15mm • Round bars: Ø45mm • Square bars: 40mm • Triangular notching: 130x130x12mm • Bending: 200x12mm • Motor: 9KW • Net weight: 2500Kg

Condition: used, Year of construction: 1990, 50 t. weight 1,8 t hydraulic ja Fodpfx Aszf Nurjivogg round bar steel 40 mm

Condition: new, Year of construction: 2026, The machine is equipped with 5 workstations: • Punching station • Flat steel shear • Angle steel shear • Notching station Fgjdjzzkxqopfx Aivog • Bar steel shear (round and square) Technical Data Strokes per minute at 20 mm stroke: 37 /min Throat depth: 500 mm Punching force: 550 kN Hole diameter and thickness up to max.: 40×10 mm or 20x20 mm Flat steel up to max.: 300×15 or 200×20 mm Angle steel 90° up to max.: 130x130x13 mm Angle steel 45° up to max.: 70x70x7 mm Bar steel up to max.: 40 mm Square steel up to max.: 40 mm Notching up to max.: 10 mm

Condition: ready for operation (used), punching pressure 45.0 t punch diameter 22 in 15.0 mm punch diameter 38 in 8.0 mm round bar steel 30.0 mm square edge steel 25.0 L-beam 100 x 10.0 mm shear: flat material 300 x 12.0 mm adjustment of stroke 0 - 55 mm work height max. 940 / 1140 mm strokes per minute 34 punch diameter max. 110 mm voltage 400 V total power requirement 4.5 kW weight 1245 kg dimensions 1520 x 590 x 1700 mm In good condition (!!) Fgedexaat Ujpfx Aiveg New price ~ 13.000 Euro Special price upon request Features: - Robust electro-hydraulic profile steel shear - With multiple workstations: * Punching station * Flat steel shear * Angle/profile steel shear * Notching station - Continuously adjustable stroke - Very compact design - Support table at the notching and punching station - Side support surfaces - 1x freely movable foot switch - Central lubrication system - Connection cable + connector

Condition: used, functionality: fully functional, Equipment: foot remote control, We are selling a well-maintained profile steel shear/punching machine, Peddinghaus Type 210 AD/13, from our workshop. Integrated functions: Hole punch Bar steel shear Profile steel shear Flat steel shear Notching device The machine thus combines several processing steps in a compact unit and is ideally suited for flexible use in steel and metal construction. Fgodpfxsziz Ewj Aiveg Condition: The Peddinghaus is in perfect working order and is ready for immediate use. Accessories: Various tools included Foot pedal available Important note: Due to the machine's high weight, shipping is unfortunately very difficult or only possible with significant logistical effort. We therefore recommend picking it up. Inspection: The machine can be inspected on-site at any time and tested during a trial run – this way, you can convince yourself of its functionality. We are available to answer any questions and provide further details.

Condition: used, puncher 70.0 t round bar steel 45.0 mm square edge steel 45.0 x 45.0 mm L-beam 150 x 150 x 13 mm hole punching press: capacity (dia. x thick.) Ø 27.0 x 20 mm Fgodpfx Aioy Uy Sioveg shear: flat material 450 x 15 / 300 x 20 mm throat 300 mm work stroke 70.0 mm work height max. 1095 mm total power requirement 9.0 kW weight 1925 kg range L-W-H 1800 x 1200 x 2000 mm current new price approx. 25.000 euros special price on request Equipment: - electro-hydraulic profile steel shears with 4x work stations * flat steel shears * profile steel shears * hole punch * notching station - driven by two hydraulic cylinders - stepless stroke adjustment - support table at hole punching & notching station - material stripper - side storage options - 2x freely movable foot switches - operating instructions (PDF)

Condition: like new (used), Year of construction: 2012, round bar steel 45 mm square edge steel 45 mm L-beam 120 x120 x 12 mm total power requirement 5,5 kW weight of the machine ca. 1600 kg Fgsdpfx Ajy Hxq Ijivjg dimensions of the machine ca. 1700 x 950 x 1900 m

Condition: used, Year of construction: 1978, serial number 4412956673057 95 to. ca. engine output 7,5 kW Fgsdey Hl Rbopfx Aiveg weight of the machine ca. ca 5 t dimensions of the machine ca. 2,2 × 1,0 × 2,3 m Technical specifications (from the label)Angle steel (L-profile):150 × 15 mm at 90°100 × 14 mm at 45°Flat steel:up to approx. 150 × 16 mmlarger cross-sections up to 340 × 16 mm (depending on function)Beam profiles:U-profiles (UPN): 220I-sections (IPN)

Year of construction: 1995, condition: used, A Geka ironworker with integrated punching unit for punching and shearing flat bar, section steel and bar stock is offered. Punch diameter/material thickness: 28mm/13mm, flat bar shearing capacity: 300mm×10mm/200mm×13mm, max. round bar diameter: 30mm, max. square bar dimensions: 30mm×30mm. Including tool cabinet with various punch and die units as well as a stop extension to 3m. The flat bar and section steel shearing units were hardly used. An on-site inspection is possible. Fodpfx Aiszybuasvegg

Condition: used, functionality: fully functional, Year of construction: 2016, Flat shear blades, 520 mm long, with four cutting edges, also for shearing angle iron 45° Fedoy Ndt Hspfx Aivegg material support table with gauge stops on the flat shear station section shear knife for shearing angle iron 90° as well as rounds and squares quick-change punching attachment up to 39 mm Ø, for punches and dies of the blue series or with universal die block for die no. 3 height-adjustable and swing-away stripper with exchangeable plate square notching attachment material support table on the notcher station two two-stage foot pedals and electric control elements on the punch station and notcher station hydraulic low pressure spotter for foot operation connecting sockets for external engagement, e. g. via electrical length stop integrated hydraulic power-pack

Condition: good (used), Offer 23477 Hydr. flat profile and bar steel shears and hole punch Technical data: - Flat steel shears cut up to 350 x 12 mm Fsdpfxjra Avdj Aivjgg - Steel section shears - cuts L-steel 90° up to 100 x 10 mm - Steel bar shears - cuts round steel up to 32 mm - Notching device - Rectangular notcher 50 x 90 mm - Hole punch - punching force 550 KN - with stop table - throat depth 220 mm - punches holes in steel up to 32 Ø in 12 mm - Coordinate table - manual stop - E. foot switch - Drive 400 V / 2.2 kW - Space requirement approx. W 900 x H 1750 x D 1700 mm - Weight approx. 1200 kg

Condition: used, Year of construction: 2009, gebraucht 2009 9725 prompt, Zwischenverkauf v Spanien 14700 € 1 110 to Fgsdpfx Aiewiq D Ejveg 300 mm 5 2 40x20 (28x28) mm 80 mm 17 1/min 600x15 (400x20) mm 605 mm 152x152x13 mm 50/50 mm 90x52x13 mm 5 kW 2130 mm 1200 mm 2200 mm 2500 kg 2 foot pedals for independent work at 2 stations hydr. drive flat bar shear with hydraulic downholder angle bar shear with minimum deformation by diagonal moving of the blade , with hydraulic downholder round and square bar shear rectangular notching unit punching unit up to diam. 40 mm oilfilling table at the punching station with gauge table at the notching unit with gauge table at the flat bar shear BUYING USED MACHINERY IS A MATTER OF TRUST - OUR TRANSPARENCY PROMISE We offer you maximum security and complete transparency. • HONEST INSIGHTS: Detailed photos and functional videos of the current condition • LIVE ON-SITE CHECK: Live testing is possible at our facility • DIGITAL DEMONSTRATION: Individual live demonstration via video call • RISK-FREE PURCHASE: 14-day return policy Details:

Condition: used, Year of construction: 2011, You are bidding on: a branded folding press from a very reputable and well-known manufacturer – Geka. Device features: - Folding press - Rail bends cleanly – test possible - Degree indicator - Bending length: slightly over 2 m Fgjdpoyk H E Tjfx Aivog - Sheet thickness: 2 mm (iron sheet; greater possible for aluminum, zinc, etc.) - Machine bends pneumatically via foot pedal - 15 cm front rail removable, leaving a 1 cm rail (desired by many; together 2.5 cm) Guillotine shear HT 200 or Schröder electric guillotine shear, 2 m – 2.5 mm ... manual lever shears also optionally available. Important: Optionally, you can find and purchase a wide range of machinery and machine accessories (e.g., different rails, depth stops) for sheet metal and steel processing in our shop. This includes folding presses, guillotine shears, drill presses, slip rollers, slitting and profiling machines, and corresponding accessories (beading devices, round rollers for gutter production, back gauge, etc.), as well as additional hand tools and spare parts from many top manufacturers. Feel free to contact me with any questions. You will receive an invoice with VAT shown separately. Free loading is available – weight approx. 850 kg. Inspection and testing are possible and encouraged by prior telephone appointment. Payment in cash upon collection. Benefit from our experience and expertise—we will be happy to advise you. Collection by the buyer (or a shipping company commissioned by the buyer) should take place within 10 days after the end of the auction. Location: 97249 Eisingen, approx. 3 minutes from the A3 and A81 motorways.

Condition: used, Year of construction: 1984, round bar steel 45 mm square edge steel 40 mm Fedpfegvkmnex Aivogg L-beam 120 x 13 mm flat steel 500 x 12 mm punching pressure 60 t throat 510 mm 500 x 12 oder 400 x 16 mm punch diameter 27 in 17 mm punch diameter 39 in 12 mm oil volume 80 l total power requirement 7,5 kW weight of the machine ca. 2,4 t dimensions of the machine ca. 1,8 x 0,9 x 1,8 m Hydraulic machine with 5 stations so punching, notching, shearing flat iron, angle iron, solid material, punching with hand lever, profile steel side with foot switch. Punching discharge: 510 mm! All performance data refer to a material strength of 450 N / mm². Electric 380 volt

Condition: new, Year of construction: 2025, operating hours: 30 h, Panel benders (also known as swing bending machines or folding machines for sheet metal) are used across various industries where precise, automated bending of sheet metal components is required. The main sectors include: 🏭 Metalworking & Sheet Metal Processing Contract manufacturers / Sheet metal processing companies Series and single-part production Enclosures, housings, cassettes, boxes 🚗 Automotive Industry & Suppliers Structural and body components Brackets, covers, interior components Especially suited for mass production requiring consistent repeatability ⚡ Electrical Engineering & Electronics Switchgear and distributor manufacturing Enclosures for controls, servers, industrial electronics Very common use due to numerous 90° bends and complex contours ❄️ Household Appliances & White Goods Washing machines, refrigerators, ovens Internal frames, covers, claddings 🏗️ Construction Industry & Architecture Facade elements Roof and wall claddings Metal panels, cassettes 🚆 Transport & Public Transit Rail vehicles, buses, commercial vehicles Interior claddings, technical housings 🛠️ Mechanical & Plant Engineering Machine frames Protective claddings Switchgear enclosures Fgjdpfxjyb Hu No Aiveg 🌬️ HVAC / Air Conditioning Technology Ventilation ducts HVAC unit enclosures Air distribution systems 🏥 Medical Technology Equipment enclosures Stainless steel claddings High requirements for precision & surface finish Why Panel Benders in these sectors? ✔ High degree of automation ✔ Excellent repeat accuracy ✔ Ideal for complex bent parts ✔ Gentle processing of painted or coated sheets ✔ Fast processing for small to medium batch sizes

Condition: ready for operation (used), functionality: fully functional, Plate rolling machine, 3000 mm capacity, H. Vuillot 3000 mm, used machine Manufacturer: H. Vuillot Sheet capacity: 3000 x 27 mm Top roll diameter: Ø445 mm Fgjdpjwcqpnjfx Aiveg Bottom roll diameter: Ø330 mm Year: 1972

Condition: good (used), Year of construction: 1998, control type: NC control, number of rollers: 4, roller (bottom) diameter: 540 mm, roller (top) diameter: 560 mm, side roll diameter: 420 mm, roller diameter: 440 mm, roller length: 3,100 mm, overall weight: 45,000 kg, total length: 8,700 mm, total width: 2,900 mm, total height: 3,075 mm, power: 81 kW (110.13 HP), 4 roll plate bender HAEUSLER - VRM-hy MACH-ID 9638 Make: HAEUSLER Fsdpfxozbqque Aivegg Type: VRM-hy Year: 1998 Smallest bending diameter 640 mm Pressing force against upper roll 5800 kN Conical bending attachment Central lubrication Equipped for change rolls Rolling width: 3100mm Rolling thickness 3x toproll Ø:50mm Rolling thickness 5x toproll Ø:60mm Rolling thickness prebending: 40mm Top Roll Ø: 560+440mm Bottom Roll Ø: 540mm Side roll Ø: 420mm Number of rolls: 4 Rolling speed: 0-6 Adjustiment lower roll: 0 - 200mm/min. Adjustment side rolls: 0 - 500mm/min. Number of driven rolls: 2 Power: 81kW Length: 8700mm Width: 2900mm Height: 3075mm Weight: 45000kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Automatic Multi-purpose Iron Twister GLASER Type GDM 3 motor-driven rod twisting machine equipped with ring bending attachment, profile bending machine Fodpfx Aiow Dgi Tevogg Year of manufacture: 1977 Twisting length: 1200 mm Twisting speed (Level 1): approx. 10 rpm Twisting speed (Level 2): approx. 20 rpm - Spindle drive via large geared motor - Arch and ring bending machine, not complete - with HAWE hydraulic unit up to 600 bar for auxiliary functions - 4-square tool holder for twisting tools Motor power: 3.3 kW Power supply: 380 Volt, 50 Hz Space required (L x W x H): 2120 x 720 x 1100 mm Weight: approx. 600 kg Good condition

Condition: new, Year of construction: 2026, The machine has 5 workstations: • Punching station • Flat bar shear • Angle bar shear • Notching station • Bar steel shear (round and square) Technical data Strokes per minute with 20 mm stroke: 40 /min Throat depth 500 mm Punching force 800 kN Hole diameter and thickness up to max. 40×14 mm Fgodpfszzkv Ajx Aiveg Flat steel up to max. 450×15 or 300×20 mm Angle steel 90 degrees up to max. 152x152x13 mm Angle steel 45 degrees up to max. 70x70x7 mm Bar steel up to max. 45 mm Square steel up to max. 45 mm Notching up to max. 12 mm

Condition: good (used), Year of construction: 2002, machine/vehicle number: 4523, punching force: 80 t, sheet thickness steel (max.): 20 mm, Equipment: CE marking, foot remote control, IMS model HY 80 Fgodpozkwttefx Aivjg