Used Slatted Frame for sale (9,211)

Condition: new, machine/vehicle number: Produktpalette, empty load weight: 6 kg, maximum load weight: 28 kg, overall weight: 35 kg, axle configuration: 3 axles, loading space length: 15,030 mm, loading space width: 2,480 mm, loading space height: 4,060 mm, total length: 15,150 mm, total width: 2,550 mm, total height: 4,060 mm, suspension: air, tire size: 435/50R19,5, tire condition: 100 %, Additional information Chassis, semi-trailer, transport company Fine-grained steel welded construction, with preload for slight tension in the neck area, kingpin plate with interchangeable 2 kingpins X-tra Long, with an internal length of 15030 mm Outer frame slightly angled, new design with Load-Lock profile for attaching lashing straps 24-ton, 2-speed landing gear, single-side operation, with straight lower part, without thrust compensation Note: Free support foot angle or free swivel radius to the rear approx. 1930 mm Retractable ladder at the rear Door lock on the side 2 chocks with holder Aluminum side impact protection Galvanized steel under-ride protection Partial wheel arches in front of the 1st axle and behind each axle Rear impact protection Axles + Suspension SAF disc brake axles Axle/chassis laser-aligned to reduce tire wear and fuel consumption Bdsdpfji Riwusx Andji Air suspension Braking system 2-line compressed air braking system Color-coded lines for easy servicing Spring brake parking brake 2 non-interchangeable coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Caution: The semi-trailer may only be pulled by towing vehicles that guarantee the effectiveness of the ABS! with lifting and lowering valve Vehicle driving stability system AAC Basic, automatic lift axle acting on the last axle, as an aid for maneuvering, up to 20 km/h, can be manually switched off Axle load detection via EBS-Canbus signal, for display on the driver's cab, truck must be appropriately prepared, no truck installation (no calibrated scale) Wheels & Tires 435/50R19.5, manufacturer's choice Steel rims, factory silver Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the side Yellow LED lighting on the side coupled with the turn signal, flashing Side marker lights 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole non-interchangeable sockets at the front, without connecting cable Floor Sieved plywood, approx. 30 mm thick, on longitudinal supports for high point load capacity for forklift axle load up to max. 7100 kg Front wall / Corner posts at the front 2580 mm high, corner posts steel in full volume design, release mechanism for side tarpaulin on the front wall, crash blocker, at the bottom inside at approx. 140 mm height with steel impact protection Center posts 3 pairs of sliding posts that can be moved along the entire length, with 4-fold insert pockets & at the bottom with a long pocket. 3 pairs of post positions Insert slats 5 rows of wooden slats Rear wall / Corner posts at the rear Corner posts at the rear steel up to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet Rear portal doors, 2-wing with 2 internal swivel latch locks each Tarpaulin Tarpaulin, with welded-in horizontal and vertical straps Tensioning closures made of stainless steel Roof Sliding roof, rear end lift that can be folded up, with roof that can be slid from back to front, L-roof beam for the automotive industry, interior width between the roof beams approx. 2490 mm, tarpaulin color: white Roof non-elastic, hardly any deflection of the roof beam during loading and unloading EcoLift - liftable roof by approx. 380 mm, on both sides, with gas spring support, 3 driving positions at the front: Interior height at the front set to approx. 3000 mm Optimal rain gutter at the rear, at the top of the end ra

Year of construction: 2012, condition: excellent (used), Ruchser roller conveyor for windows with 90° swivel mechanism, left/right, length 4400 mm. Electrically driven nip rollers with 2 parallel support sections, pneumatically tiltable from vertical by 7°. Outer side tilted to vertical by 7°, inner side remains vertical. Support sections are 1900 mm high and equipped with rubber roller strips. Stainless steel sheets, 2 mm deep, are located between the rubber strips to create a sliding surface, along with clip holders. Infeed and outfeed sections with edge protection rollers, up to 3000 mm high, made of rubber. Infeed section 2000 mm, outfeed section 4000 mm, with driven nip rollers. Bdodpfxelpcc Ij Andei Control unit and operating elements mounted on a freely adjustable stand.

Condition: used, maximum load weight: 44,980 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, first registration: 09/2024, next inspection (TÜV): 09/2025, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Chassis, bent * Special steel frame made of high-strength fine-grain steels, electrically welded at the joints, well-dimensioned outer frame * 4-axle arrangement. Wheel protection above the axles with spray mist suppression * All steel parts sandblasted * Lateral impact protection made of anodized aluminum mounted * Increased point load of approx. 30,000 kg over approx. 4,000 mm * Special design in the bent area for maximum low-bed length in combination with AluLeg outrigger supports instead of telescopic outrigger winches, max. rear swivel radius of the tractor unit approx. 2,100 mm Special superstructure with rear beam extension * Self-supporting aluminum roof beam / profile approx. 120 x 100 mm, sliding tarpaulin with plastic flaps * Rear beams extendable to approx. 4,200 mm * Three sliding beams per side with rubber cord relief * Additional center beam locking in the roof beam and parking position, by means of a pull cable and spring latch * Lifting roof mechanically adjustable, lifting height approx. 400 mm, can be operated on both sides or on one side, without opening the opposite side and the doors * Additional height adjustment of approx. 480 mm in approx. 40 mm increments with height adjustment in the beams * Front overhang on the front wall for operation under tarpaulin up to a total height of approx. 4,400 mm * Four rows of stackable approx. 150 mm aluminum slats on the side, bottom 450 mm pockets, above 4 rows of single pockets * Only 3 rows of insert slats in the upper bed. Spacing between slats evenly distributed Floor * Approx. 27 mm special water-resistant glued beech plywood, rough surface * Steel sheet in the wheel arch area * Forklift truck accessible according to DIN standard * Outer frame flush with the surface Brakes * WABCO compressed air brake system with EBS according to EC standard 71/320 EEC including PREV (parking release safety valve) * Spring brake cylinders as parking brake * Wabco Smart Board with odometer and aggregate load indicator Axles * 4 x 10,000 kg SAF/Sauer with drum brakes in low-loader design * Air suspension with lifting and lowering device, total stroke approx. 230 mm * Third and fourth axles as friction-jointed trailing axles with electric and mechanical lock Twin tires * 235/75 R 17.5, -16-ply, incl. E-wheel holder. without E-wheel Paint finish * Chassis in RAL 3002 red, solid color Bdsdpfx Anslthgusdei * Center beams, axles coated with KTL black * Corner beams in hot-dip galvanized design * Plastic parts black * Hot-dip galvanized parts unpainted * Rims in factory silver * Superstructure in RAL color, solid color Special equipment incl. * Air suspension in ECAS design, operated on the semi-trailer * Overwidth signs front and rear in zinc-plated, steplessly telescopic design with attached warning lights including socket for rotating beacons (small panels) * Sliding tarpaulin cover locking additionally from the outside * 4 beam adapters for special outer frame profile, to lock the center beams as desired * PVC sliding tarpaulin, color similar: RAL 9006 silver * Roof tarpaulin translucent, in overwidth and overheight design, flat hooks, tarpaulin folds, closures with pawl lock /OCS * Telescopic socket for rotating beacon including beacon on the rear left * Outer frame for machine transport with app

Condition: new, • Profile width max. (mm): 90 • Profile height max. (mm): 80 • Saw blade diameter (mm): 350 • Saw blade bore (mm): 30 • Motors: 2 x 1.5 kW • Dust extraction connections: 2 x Ø 80 mm • Pressure (bar): 6 – 7 • Weight (kg): 300 • Cutting of profiles: for wood, plastic, and aluminum frames • Saw blades: 2 fixed at 45° • Pneumatic unit stroke: with two-hand operation • Adjustable stroke speed • Pneumatic slat clamping devices: within the machine cycle • Automatic slat adjustment: to profile shape • Diagram plates (mm): 700 mm long, right and left • Pneumatic length stop • Motor protection switch • Motor brakes • Tool set • Maintenance unit • Pressure monitor Machine features: • Easy to operate • Fast cycle time • Low maintenance and cleaning requirements Bjdpfx Aefiqhbsndjdi

Condition: like new (used), Lock Metal detector Model: Met30+ Bedjfhdv Ejpfx Andedi Stainless frame, slat chain belt, belt dimensions 1900mm x 80mm, aperture 140mm x 300mm, 3Ph

Condition: used, Year of construction: 1970, Press capacity: 30 ton Throat depth: 160 Ram stroke adjustable: 20 - 45 mm Slide adjustment: 10 / 60 mm Shut height (stroke down, adjustment up): 220 mm Table surface area : 470 x 300 mm Slide area: 250 x 190 mm Number of strokes: 80 - 240 s.p.m. Required power: 4 kW Dimensions L x W x H: 1.400 x 1.800 x 2.000 mm Bdedpfjuqc Ensx Andoi Weight of machine approx.: 2,67 ton Standard configuration the electric is new from 2015.

Condition: new, mileage: 450 km, power: 375 kW (509.86 HP), fuel type: diesel, overall weight: 26,000 kg, axle configuration: 3 axles, brakes: retarder, color: white, gearing type: automatic, total width: 2,550 mm, total height: 3,800 mm, loading space length: 6,500 mm, loading space width: 2,480 mm, loading space height: 600 mm, Year of construction: 2023, Equipment: ABS, air conditioning, compressor, crane, electronic stability program (ESP), navigation system, parking heater, soot filter, Cab & Comfort: GM cab (wide, long, medium height) with comfort suspension * Electric glass sunroof * Central locking with remote control, 2 vehicle keys * Comfort seat for driver (air-suspended, with lumbar support, shoulder adjustment, seat heating, armrests) * Passenger seat adjustable in length, backrest, and height * Climatronic air conditioning system, water auxiliary heater 4 kW * Comfort mattress (110 mm), slatted bed frame, headrest adjustment, various storage compartments, and refrigerator * Multifunction steering wheel (leather, height and tilt adjustable) * Comfort storage, cup holders, sockets (12V, 24V, 230V), USB ports * Interior styling "Moon Grey", LED interior lighting, orientation light, electric sun blinds ----Infotainment & Connectivity: MAN Media System Professional Navigation (12.3 inch) * MAN SmartSelect infotainment control with touchpad * Camera system * Advanced sound system with subwoofer * Professional instrument cluster 12.3 inch * Europe navigation map, online traffic information, smartphone integration * Connectivity Board module ----Safety & Assistance Systems: Electronic Stability Program (ESP) * Traction control (ASR) * Cruise control, speed limiter * Emergency brake assist (EBA, non-deactivatable) * Lane departure warning (LDW) * Attention warning (MAN AttentionGuard) * Full brake assist, ABS, EBS * High-performance engine brake (EVBec) * Retarder Eco * Disc brakes on all axles, electronic parking brake * Brake pad wear indicator * Hill start assist (EasyStart) ----Lights & Visibility: H7 headlights * LED daytime running lights * Fog lights * Cornering lights * Automatic headlight leveling, high beam assist, light sensor * LED taillights, side marker lights, outline lights * 2 LED rotating beacons on cab roof, work lights (LED) * Electrically adjustable and heated exterior mirrors, curb mirrors * Automatic windshield wipers with rain sensor * Sun visor ----Drive & Chassis: MAN D2676 LFAF diesel engine, 375 kW (510 hp), 2,600 Nm, Euro 6e * MAN TipMatic 12.26 DD automatic transmission with retarder * Auxiliary drives (transmission-dependent, switchable, continuous operation) * Air suspension on all axles, automatic level control * Differential lock, rear axle * Digital axle load indicator ----Container/Flatbed Body: Folding side walls * Wooden floor with anti-slip coating * Lashing points in the floor * Aluminum storage boxes * Trailer coupling (RINGFEDER RF40/G150A) HMF 5020 RCS K7 loading crane, year of construction 2022, fully hydraulic with oil cooler * Knuckle boom with endless slewing range * Scanreco radio control system with remote control * Crane height indicator HEW * EVS-D safety system with AutoSwitch * 2-stage LMB (Load Moment Blocking) * EVS inclination monitoring system * Dynamic load adjustment EVS-H * MKG 4-point auxiliary support (4 hydraulic cylinders) * Support width front: 5.6 m / rear: 7.85 m * Max. 19 m reach with max. 1730 kg lifting capacity * At 4.8 m reach, max. lifting capacity of 9040 kg * Includes jib FJ600 (reach extension) * Max. 29.40 m reach with 430 kg lifting capacity ----* Tire dimension front axle: 385/65R22.5 * Tire dimension rear axle: 315/70R22.5 * Fuel tank: 590 liters * AdBlue tank: 60 liters * Technical permissible total weight: 28,000 kg * Unladen weight: 19,644 kg * Permissible trailer load: 27,862 kg * Overall length: 10,720 mm * Wheelbase: 5,500 mm Bdsdpfx Ansvhv Iujdei * Next inspection due: / ----Vehicle number: 8816----Errors and prior sale excepted----Advertising and various

Condition: good (used), Year of construction: 2005, Used machine MAKA PE 70 5-axis CNC machining center for machining wood and plastic. Machine in mobile portal design, with rack and pinion drive. Year of manufacture: 2005 Technical data: CNC control BWO 920 for 5-axis machining. LCD display 10.4" 2 MB NC memory, mobile control panel. Working areas in 5-axis operation, with tool diameter 60 / length 160 mm: Y-axis: 5,500 mm X-axis: 1,250 mm Z-axis: 300 mm / with 180 mm installation height (upper edge of vacuum suction cup) Working areas in 3-axis operation, with tool diameter 60 / length 160 mm: Y-axis: 5,900 mm X-axis: 1,250 mm Z-axis: 300 mm / with 180 mm installation height (upper edge of vacuum suction cup) A-axis 540° (rotation axis) B-axis 196° (swivel axis +/- 98°) Rapid traverse speed X/Y axis 45 m/min. Z-axis 24 m/min. A/B-axis 10 m/min. Milling unit: - 1 universal unit for 5-axis milling with 50° inclined head, power 7.5 kW (S1) 10 kW (S6), speed continuously adjustable up to 22,000 rpm, milling spindle HSK-F63, water-cooled. - 1 NC height-adjustable chip collection system with slat curtain. Tool magazine: - HSK-F63 tool interface for automatic tool change system. - 1 horizontal drum magazine, with 20 spaces for tools up to D = 90 mm, with sorted storage up to max. 160 mm. (Three spaces are required for this). Machine table: - 10 support tubes on linear guides with pneumatic release device for quick positioning. - 2 x control circuits for "lifting / lowering" stops - 2 x control circuits for "lifting / lowering" slide bar - 2 x control circuits for "clamping / releasing" pneumatics - 2 x vacuum control circuits with button for clamping and automatic reset through CNC programming. - 1 chip conveyor belt integrated in the base frame, for removing chips and small waste up to max. approx. 100 x 100 x 100 mm. Vacuum supply: - Machine designed with vacuum system. - 2 x vacuum clamping circuits - 1 vacuum pump, suction capacity per vacuum pump approx. 130 m³/h, with tank. - Vacuum supports with various suction plates. Bdedjvr A A Tspfx Andji Other: - Automatic central lubrication. - Control cabinet with air conditioning unit. Work safety: - Mobile protective cabin with safety bumpers on the operator side. Repairs / maintenance before delivery: - New maintenance. - New slatted curtain on the portal - New sliding window - New Y-axis energy chain - New Z-axis energy chain - Various cables and air hoses replaced.

Condition: good (used), Year of construction: 2001, functionality: fully functional, Used machine MAKA PM 270 R 5-axis CNC machining center for machining wood, plastic and aluminum. Machine in mobile portal design, with rack and pinion drive. Year of manufacture: 2001 Technical data: CNC control BWO 900C, for 5-axis machining. Integrated PC with 1MB memory and 3.5" floppy disk drive. Mobile control panel stand. Working areas in 5-axis operation, with tool diameter 60 / length 160 mm: Y-axis: 5,600 mm X-axis: 1,350 mm Z-axis: 420 mm / with 180 mm fixture height (vacuum suction cup) Bdjdevmywqopfx Andsi Working areas in 3-axis operation, with tool diameter 60 / length 160 mm: Y-axis: 6,000 mm X-axis: 1,350 mm Z-axis: 420 mm / with 180 mm fixture height (vacuum suction cup) A-axis 540° (rotation axis) B-axis 200° (swivel axis +/- 100°) Rapid traverse speed X/Y axis 45 m/min. Z axis 24 m/min. A/B axis 10 m/min. Milling unit: - 1 universal unit for 5-axis milling with 50° inclined head, power max. 12.5 kW, speed continuously adjustable up to 17,000 rpm, milling spindle water-cooled. - 1 NC height-adjustable chip collection system with slat curtain. Tool magazine: - ISO 40 tool interface for automatic tool change system. - 1 chain tool magazine with 32 spaces for tools up to D = 90 mm, with sorted storage up to max. 160 mm. (Three spaces are required for this). Machine table: - 10 support tubes on linear guides with pneumatic release device for quick positioning. - 2 control circuits for "lifting/lowering" stops - 2 control circuits for "lifting/lowering" slide rail - 2 control circuits for "clamping/loosening" pneumatics - 2 vacuum control circuits with button for clamping and automatic reset through CNC programming. - 1 chip conveyor belt integrated in the base frame, for removing chips and small waste up to max. approx. 100 x 100 x 100 mm. Tools: Tools are not included in the scope of delivery! The system can be delivered including various tool holders upon request. We would be happy to make you a separate offer for this. Vacuum supply: - 1 vacuum pump, approx. 140 m³ suction power, including a tank with a capacity of 250 liters for quick vacuum build-up. - 10 vacuum supports with various suction plates. - Various clamping devices for posts and curved parts. - Raise/lower stops to position components. Other: - Automatic central lubrication. - Control cabinet with air conditioning unit. - Projection laser Work safety: - Mobile protective cabin with safety bumpers on the operator side.

Year of construction: 2021, condition: excellent (used), Syspal 600HA2 Eurobin wash frame Bdsdpenbdtiefx Andsi 2021, stainless, SWL 50Kgs, 3Ph

Condition: new, Year of construction: 2026, Butterfly Table BS20 Randek butterfly table BS20 is an efficient tool when producing prefabricated walls, roofs, floors, gable ends in timber or steel frame. The tables can be used separate or placed in a line. High quality is achieved due to the clamping function that guarantees the squaring of the building component. The turning of the building element is done with a controlled automatic process. High productivity is achieved; the working table is optimized for prefabricated house production. Functional description: Bsds Nn Hyopfx Andsdi The following processes can be done in the working table / butterfly table: • Automatic turning of building component, the up raiser table raises and flips over the building component during a controlled process to the receiver table, and the building component is turned. • Squaring of building component, the pneumatically clamping function on the long side of the table presses the building component into a squared high quality building component. • The table is developed in order to efficiently perform the following processes: building of framework, put on and nail sheets, nailing of plastic of paper foil and insulation of building component. Technical description: • Length: Available in lengths of 6000, 7500, 9000 and 12000 mm • Width adjustment between 2250 – 3100 mm, the adjustment between different widths is easily done with a manual control • The tables are hydraulically appraisable up to 91 degrees • Pneumatically squaring function on the up raiser table on the long side, stoppers height 160 mm • The tables are covered with plywood sheets as far as technically possible, the sheets makes it possible to put on sub components and beams easily directly on the table • The tables are built in strong steel profiles • The working height of the tables is optimal 620 mm • Equipped with alongside c-profiles for possible placement of steer stoppers for beam placement • The tables are completely delivered ready for assembly with very simple installation process. The customer is responsible for supply of motor cover and switcher for hydraulic unit (3kW) • The tables are designed to make it possible to add a multi function working bridge with nailing or drilling function • The distance between the tables shall be approximately 1100 mm, depending on the thickness of the building component Security: • The machine is equipped with safety stop CE-marked Benefits: • Squared building components due to clamping function • Controlled and automatic turning of the building component • Ideal working height • Flexible adjustment in width

Condition: good (used), Year of construction: 1990, functionality: fully functional, ORMA Hydraulic Frame Presses DE 30/18 Manufacturer: Orma Machine Italy Year of manufacture: 1990 Maximum working dimensions: 3000 x 1800 mm Maximum working depth: 90 mm Bsdpfsv Iv Sgsx Andedi Vertical pistons: 2 Maximum piston pressure: 2000 kg Horizontal pistons: 2 Motor: 0.55 kW Width = 850 mm Length = 3700 mm Height = 2310 mm Features: Robust frame Easy adjustment and adjustment of the orthogonality and parallelism of the cross members Working accuracy Easy locking and control of the double-acting pistons Installation for small workshops and for assembling and aligning various components such as doors, windows, louvre doors and windows, simple frames, etc. The pistons are oil-driven.

Condition: good (used), functionality: fully functional, Technical specifications: Manufacturer: Striebig Bedpfx Anewdig Iedodi Type: Standard II Plus 6220A Year of manufacture: 5.92 Feed: manual Design: automatically adjustable aluminum slatted frame Saw carriage lock: manual Saw unit plunge-cut: manual Swivel adjustment from 0 to 90°: manual Motor power: 4.4 kW Cutting area: 5600 × 2200 × 80 mm Speed: 4750 rpm Saw blade diameter: 300 mm Space required: L × H × W 6400 × 2900 × 1600 Condition: good (all ball bearings new, red plastic strips new) Location: Warehouse Installation: Wall-mounted, freestanding A forklift is available for loading. Installation and delivery available upon request.

Condition: new, machine/vehicle number: A2306/9210, The pneumatically working drawer clamp type Box V3.0 ensures a simple and fast assembly of drawers and frames. Thanks to its functional design, it is possible to press single parts as well as complete drawers with different connections. This way, a perfect connection as well as shape of the drawer can be guaranteed. Because of the special clamping process, folding connections and drawer fronts with glass insets cannot be deformed. Maximum clamping power: vertical: 800 kg / horizontal: 800 kg Adjustable depth stops allow clamping of drawers with longer fronts Lateral press units slowly approach the workpiece Machine operation via joystick. Special equipment: - Digital positioning readout - Kit Door (for frontal clamping of drawer corners) Bodpfx Anogqfnzsdodi Advantages: - High flexibility: Variably adjustable clamping unit for drawers and frames of different dimensions - Minimum set-up times allow high output - Intuitive operation - High safety standards due to CE-conformity e.g. 2-hand-operation - Plug & Play

Condition: new, Year of construction: 2025, A compact design sheet fiber laser metal cutting machine with complete protection Small occupied space balances complete protection and higher safety. Each frame of the cutting machine bed is welded after mortise-and-tenon joint to achieve perfect mechanical property and better stability and firmness. The pull-out cutting machine table, with the electric table optional, saves space occupation and freshen up the user operation experience. Convenient and fast open&close with one click; The laser cutter door is safe and reliable, by using rack-pinion transmission mode combined with self-locking cutting machine system Bdjdpfxjhwv N Ho Andsi Fiber laser heads are able to detect jutting obstacles to effectively reduce the damage rate and save the maintenance cost of a laser cutter. Applicable Material: metal Condition: New Laser Type: Fiber Laser Laser Power: 1500W, 2000W, 3000W, 6000W, 12000W Cutting Area: 1000*1500mm Cutting Speed: 0-100m/min Positioning accuracy: ±0.05mm Repositioning accuracy: ±0.03mm Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING

Condition: used, Year of construction: 1994, Frame press, Schafberger & Sprödhuber Bsdpfx Asilurnjndjdi Type Super 4 kW 3 m x 6 m

Condition: used, Year of construction: 1991, Name: Used Filter Press Frame Manufacturer: Passavant Type: 1200 x 1200 mm Year built: 1991 Construction form: Bridge beam press Filter pressure: 15 bar Press content: Possible approx. 2200 liters m2 Cycle: Closed Filter area: Possible approx. 160 m2 Plate size: For 1200 x 1200 mm Number plates: Without plates, 66 plates fit with a cake thickness of 30mm Plate transport: Automatic Filter cloth washer: Yes Cake thickness: 30 Possible Dimensions: L 6.700 x W 1.800 (2.400) x H 2.250 + 500 mm Empty weight: Approx. 14000 kg Technical doc.: Yes Bodpfew Aw Rlex Andjdi Message: Without plates but with 66 carriages for hanging the filter plates Accessories: A light curtain, a filter cloth washing system Condition: Second hand Price: On demand

Condition: new, Year of construction: 2025, functionality: fully functional, ACTION M frame press Press for any kind of window system: windows, slatted shutters, shutters and solid wood doors. Max working dimensions L x H 3500x2500 mm Min working dimensions L x H 250x375 mm Max vertical/horizontal thrust 7,4/2 ton Working height 480/1050 mm Hydraulic pump power 2.1 kW Bsdpfxswh T Dlj Andjdi MACHINE COMPOSITION: ACTION M ACTION M FRAME PRESS num 1 109831 Normative CE per SM 1 R00494 action m 35-25 1 930731 Volt 400 EU 1 931201 Frequency 50 Hz 1 530074 PVC-coated beams working surfaces 1 530075 Intermediate manual crossbeam complete of piston and counter-stop 1 530076 Hydraulic system for low pressure working 1 530077 Equipment for trapezoidal products with oscillating head to adapt to the different corners of the windows system 1

Condition: new, Bernardo Frame Press HRP 3000 Robust and torsion-resistant hydraulic frame press with high-quality pressure cylinders. Whether it is used for furniture or door production, block or frame gluing, the high pressing force of 2,000 kg per cylinder and precise, angle-accurate pressing of large-sized components enable all tasks to be carried out effortlessly. Technical Specifications Working length: 2,400 mm Working height: 1,550 mm Cylinder stroke: 95 mm Pressing force: 2,000 kg Vertical hole pitch: 50 mm Horizontal hole pitch: 160 mm Overall length: 3,250 mm Overall height: 2,070 mm Frame depth: 925 mm Weight: approx. 315 kg Bdjdpfxoxrnvbj Andei Features • Versatile use, e.g. for frame, window, and door production • Robust frame press with solid steel construction • Centralized control of the hydraulic cylinders including pressure gauge • Efficient gluing thanks to hydraulic design • Pressure cylinders equipped with rocker plates as standard Scope of Delivery • 4 movable pressure beams, each with one vertical hydraulic cylinder and counter support • 1 movable pressure beam with two horizontal hydraulic cylinders • 1 movable, adjustable pressure yoke

Condition: new, *IMMEDIATELY AVAILABLE* Includes: Door-ramp combination Equipment: - Fully aluminum superstructure - Parabolic spring suspension - Slatted floor Net: €8,848.74 / Gross: €10,530.00 Article number: ITA235371518.05 Technical data: • Brand: Ifor Williams • Model: TA5 HD • Vehicle type: Livestock trailer • Vehicle condition: New • First registration: Without first registration • TÜV/MOT: 2 years from first registration • Internal dimensions (L x W x H): 372 x 156 x 183 cm • External dimensions (L x W x H): 525 x 207 x 235 cm • Loading height of the floor: 42 cm • Permissible total weight: 3,500 kg • Unladen weight: 1,042 kg • Payload: 2,458 kg • Chassis: Low loader (wheels next to the superstructure) • Tires: 175/75R16C • Suspension: KNOTT parabolic spring suspension • Support wheel: Yes • 100 km/h approval: Optional, can be retrofitted DESCRIPTION • Reinforced, robust, bolted V-drawbar • Very stable steel frame, welded • Frame completely hot-dip galvanized • Many cross members, allowing high point loads • Floor made of pressure-treated wooden planks and 2 mm thick aluminum tread plate • Aluminum walls • Divisible entry door on the left-hand side • Interior light • Solid, hot-dip galvanized frame • Heat-reflecting roof • Ventilation openings on the side at the top of the roof • Additional ventilation openings on the side at the bottom • 2 side supports for additional stability at the rear • Rear door made of aluminum with integrated steps • Rear door with flap-door combination (switchable between a complete ramp and individual hinged doors) • Hinged slatted floor at the rear of the ramp, made of aluminum • Parabolic spring axles from KNOTT for maximum driving comfort Bedpsx Sxibjfx Andedi • Large 16-inch tires for optimal road holding • Spare wheel with bracket • Reverse automatic function • KNOTT overrun device and parking brake • Lockable coupling head • 13-pin plug with spiral cable • Reversing light • Large-dimensioned safety lighting • Integrated rear fog light • Spare wheel with bracket • Central support wheel _____ Accessories can be retrofitted by our specialist workshop!! - Feel free to request any desired modifications! _____ - Financing or leasing possible - Nationwide delivery possible - All prices include VAT - Vehicle registration document can be sent in advance, or transfer license plates (Germany) can be provided. - Export license plates including customs registration possible Descriptions and images are subject to copyright!! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers immediately available for you! We have been Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix - specialist dealers & repair - workshop for over 30 years. - Errors, omissions and prior sale excepted -

Condition: new, *IMMEDIATELY AVAILABLE* Includes: Door-ramp combination Equipment: - All-aluminum body - Leaf spring suspension - Slatted floor Net price: €10,235.29 / Gross price: €12,180.00 Article number: ITA235431721.05 Technical data: • Brand: Ifor Williams • Model: TA510 • Vehicle type: Livestock trailer • Vehicle condition: New • First registration: No first registration • TÜV/MOT: 2 years from first registration • Internal dimensions (L x W x H): 434 x 178 x 214 cm • External dimensions (L x W x H): 582 x 228 x 265 cm • Loading height of the floor: 42 cm • Permissible total weight: 3,500 kg • Unladen weight: 1,210 kg • Payload: 2,290 kg • Chassis: Low-loader (wheels next to the body) • Tires: 175/75R16C • Suspension: KNOTT leaf spring suspension • Support wheel: Yes • 100 km/h approval: Optional, can be retrofitted DESCRIPTION Bodjx Sxizspfx Andjdi • Reinforced, bolted V-drawbar • Very stable steel frame, welded • Frame completely hot-dip galvanized • Numerous cross members for high point load capacity • Floor made of pressure-treated wooden planks and 2 mm thick aluminum tread plate • Aluminum walls • Divisible entry door on the left side • Interior light • Solid, hot-dip galvanized frame • Heat-reflecting roof • Ventilation openings on the side at the top of the roof • Additional ventilation openings on the side at the bottom • 2 side supports for extra stability at the rear • Rear door made of aluminum with integrated running boards • Rear door with flap-door combination (switchable between a complete ramp and individual hinged doors) • Hinged slatted floor at the rear of the ramp, made of aluminum • Parabolic spring axles from KNOTT for maximum driving comfort • Large 16-inch tires for optimal road handling • Spare wheel with bracket • Reverse automatic • KNOTT inertia coupling and parking brake • Lockable tow coupling • 13-pole plug with spiral cable • Reversing light • Large-sized safety lighting • Integrated rear fog light • Spare wheel with bracket • Center support wheel _____ Accessories can be retrofitted by our specialist workshop! - Please feel free to request any specific requirements! _____ - Financing or leasing possible - Delivery throughout Germany possible - All prices include VAT - Vehicle registration document can be sent in advance, or short-term registration plates (Germany) can be provided. - Export registration plates including customs declaration possible Descriptions and images are protected by copyright! Anhänger Zentrum BAUMANN GmbH Dekkers Waide 17 46419 Isselburg Over 1,200 trailers available for immediate delivery! We have been Brian James / Blyss / Debon / Humbaur / Hapert / Unsinn / Cheval Liberte / Koch / Lorries / Martz / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix - authorized dealers & repair workshops for over 30 years. - Subject to errors, omissions and prior sale -

Condition: new, Year of construction: 2026, laser type: fiber laser, laser power: 12,000 W, FIBER CUT laser cutting machines are a revolutionary solution in the laser cutting market. Innovative fibre laser technology allows much faster, more efficient and cheaper cutting of sheet metal parts compared to CO2 lasers. The cutters are characterised by high speeds, productivity and exceptional cutting accuracy. They provide unrivalled precision and repeatability. Our fibre lasers are primarily designed for processing materials such as: - Independent metals - Aluminium - Stainless steel - Carbon steel SOURCE POWER 12000W CONSTRUCTION The frame of our laser is designed and manufactured from scratch in our factory. The high-quality steel used for the machines is cut, then welded and precision-machined. The entire frame, gantry and gate arms have additional ribbing to achieve high rigidity and eliminate vibration and deformation. DRIVES High-resolution, high-power Schneider AC servo system motors (Y1Y2 x 2000W, x 1500w, z 400W) have been used to drive our machine tools, ensuring adequate acceleration and speed in each direction. Drive transmission is via high-performance planetary gears. The X and Y axes use the classic and proven helical slats, which ensure long life and precision. HEAD A liquid-cooled, WSX head is used for cutting sheet metal. A high-performance quartz glass lens focuses the diffused laser beam on the material to be cut, ensuring high cutting accuracy. For the process to proceed correctly, the HSU system adjusts the head height taking into account material irregularities. A safety window located between the nozzle and the lens protects the lens unit from splinters of molten metal. LASER SOURCE The laser uses a Raycus Laser light source with high electro-optical conversion efficiency, low power consumption and high beam quality. In addition, it allows faster and more efficient operation and contributes to the elimination of operator errors. In addition, the source is resistant to backscattering, i.e. the beam returning to the laser. Good power stability ensures efficient working while consuming low energy. COOLING The S&A CWFL industrial dual-temperature units are specially designed for cooling fibre lasers. They have multiple alarm functions: compressor time delay protection, compressor overcurrent protection, water flow alarm and high/low temperature alarm. Bjdpjx Tpcbsfx Andodi INTERCHANGEABLE WORKTABLE The interchangeable work table located at the rear of the machine reduces laser downtime to a maximum. Automatic table replacement takes just 10 seconds. This gives the operator time to take the cut parts from the table and load a new sheet while the laser is working on the other table. This system ensures a very high production flow. AUTOMATIC LUBRICATION SYSTEM To keep the machine in good condition - the gears and guides need to be lubricated with oil at most every few days. An automatic system starts the lubrication every specified time and in the correct amount, and all parameters are set in the software.

Condition: excellent (used), functionality: fully functional, overall weight: 70 kg, inner dimension length: 1,200 mm, inner dimension width: 800 mm, inner dimension height: 800 mm, stack height: 4 mm, load capacity: 900 kg, empty load weight: 70 kg, total length: 1,240 mm, total width: 830 mm, total height: 970 mm, mesh size: 50 mm, We offer foldable Gitterbox containers in two sizes: 1240x830x970mm (price: 89 Euro/piece) and 1240x830x800mm (price: 70 Euro/piece). These containers have been professionally refurbished and are damage-free. They are available in the following colors: gray RAL 7030, blue RAL 5002, and green RAL 6005. Approximately 2,000 units are available. Prices are net. Our warehouse is located in Poland, PL63-460 Biskupice Ołoboczne. We can arrange delivery throughout Europe. We deliver within Poland, the Czech Republic, and Slovakia using our own transport. Rental possible. This price applies only to full truckload orders. We do not ship individual items or small quantities. Bdsdpexzdipjfx Andji

Condition: used, Year of construction: 1988, usedmake Hesstype Hydro-Spezialyear of construction 1988cylinder horizontal 2working width 3550 mmworking height 2350 mmpressing depth 100 mmweight approx. 2000 kgstorage location 97447 Gerolzhofen, free loaded, unpackeddelivery as seen,without guarantee and warranty Bdsdpfx Anovwfw Dodei

Condition: good (used), Year of construction: 1996, double-sided top and bottom sanding with sanding shoe and dust brush max. sanding width 300 mm max. sanding height 200 mm Bdedpfx Anoxfl Eajdoi year of manufacture 1994 with CE mark