Used Thread Clip for sale (2,526)

Condition: good (used), Thread cutting machine, pipe thread cutter -for: Pipe size max. 2 inches -Cutting jaws: 1" inch -Drive: via 3 gearboxes Iedpfx Aajb A Rzwsnjtr -Dimensions: 550/360/H240 mm -Weight: 60 kg

Condition: like new (used), functionality: fully functional, Thread rolled both ends the same time! Diameter range M6-M16 Max total length 600 mm. Max threaded length 60 mm. Adjustment is not difficult at all. We could offer machine with dies according to your wish, be made by our factory too. We are located at Athens, Greece, near to the center. You can view machine under power after appointment. Itedpfjwalx Eox Aaner

Year of construction: 2000, condition: excellent (used), Thread cutting machine make ROTHENBERGER TYPE:3S-G year of construction ca.2000 Itodpfjmn Thhex Aaner Without cutting head with pipe cutter and end burr device. Runs with V230 current. In top condition, like new.

Condition: as good as new (ex-display), Durkopp adler -3-TRANSPORT -1 NEEDLE WITH TRIM-KNIFE -THREAD TRIMMER Isdpjhc Nbfsfx Aanjtr

Year of construction: 2007, condition: used, functionality: fully functional, machine/vehicle number: SN.2007, Precision Worm Grinding Machine Model H10. Processing range: φ5-100×500 mm. Manufactured by Grinberg (Switzerland) in 2007, complete with a full set of accessories (video and precision inspection report available). Itedpfexgcuhjx Aanjr

Condition: excellent (used), functionality: fully functional, Brehmer Polygraph 39-3/4 thread sewing machine for bookbinding. Includes extensive accessories and consumables. Machine is well-maintained and in very good condition. Comes with manual and complete documentation – very rare. Electrical connection 400V/50Hz. Itsdpfxoxa Afmo Aanjr

Condition: good (used), Thread cutting head with Strehler jaws, thread cutting die, thread cutting machine, pipe thread cutter, cutting head, bolt cutting head Ijdjix Rcdjpfx Aanjtr -Manufacturer: Ridgid, Thread cutting head model 811A 1/8 to 2 inch -Pipe size: 1/8 to 2" -Bolts: 1/4 to 2" -Dimensions: 260/240/H70 mm -Weight: 5.6 kg

Condition: used, 2 Used Thread Rolling Machines WMW UPW25 ---Only 10.000,00 Euro--- Isdpfxex Dmnyo Aanjtr

Condition: used, Year of construction: 2007, pressure 20 - 300 kN Iedpow E Nmksfx Aanotr adjustment of rolling slide 50 mm diameter of rolling spindle 120 mm roll spindle height over machine bed 200 mm Control SIN 840 D taper length of the roll spindle 200 mm rolling spindle turning speeds 0 - 50 1/min torque per rolling spindle 2700 Nm power capacity 2 x 8,4 kW distance between rolling spindles min. 271 / max. 368 mm rolling tool outer diameter max. 300 mm total power requirement 26 kW weight of the machine ca. 7,1 t dimensions of the machine ca. 9,70 x 4,50 x 3,80 m CNC machine for gear cold rolling / thread rolling Hydraulic rolling process Felsomat loader cell Complete housing

Condition: good (used), Max. drilling capacity ∅20 mm/ 600 N/mm2 Total stroke 125 mm Working stroke, continuously adjustable 125 mm Feed force at 6 bar 4130 N Max. transferable. Torque 80 Nm Speed range at 50 Hz 360–5800 min-1 Speed range at 60 Hz 432–6960 min-1 Max. permissible speed 8000 min-1 Feed rate 30–2400 mm/min Air consumption 0.45 l/cm stroke Isdpfovxryhsx Aanetr Concentricity 0.01 mm Tool holder – standard ISO 30 / HSK 50 Inductive limit switch 24 V Normal voltage 230/460 V Motor speed at 50 Hz 2900/1450/970 min-1 Motor speed at 60 Hz 3480/1740/1160 min-1 Motor power at 50 Hz 1.5 kW / 1.1 kW Motor power at 60 Hz 1.8 kW / 1.3 kW Weight / color 73 kg / RAL 5012

Condition: excellent (used), REMS TORNADO 2010 THREADER Product description: - Reliable, highly efficient machine for threading, cutting, deburring, threading of nipples, rolling - For installations, locksmiths, production plants - Strong, compact, adjustable design suitable for construction sites and workshops - Operating principle: rotating material - stationary tool - Automatic: clamping chuck, universal threading head, lubrication and cooling - Large workspace and chip container - Adjustable material support - Extremely strong and fast drive e.g.: 2” thread only 15s Isdpjv T Truefx Aanetr - Completely maintenance-free gear in a closed oil bath - Two base versions: - portable version on 3 legs, with a removable, large oil tray and chip bowl - T version with a combined, larger oil tray and chip container, for installation on table. A fixed base or a trolley with space for putting away the material, for easy transport, with an optimal working height, stable, as additionally paid equipment - Three high-performance motors to choose from: - a high-performance universal motor, 1700 W, overload protection, rotation speed 53 1/min. - a capacitor motor 2100 W, overload protection. Two rotation speeds 52 and 26 1/min., also under full load. Very quiet operation. - a three-phase motor, 2000 W, overload protection. Two rotation speeds 52 and 26 1/min., also under full load. Very quiet operation. - A convenient two-stage foot safety switch with an emergency button, thanks to which the entire body weight is loaded during work - Two automatic clamping holders with self-centering clamping jaws. Quickly and easily clamp and release the material - Self-clamping chucks ensure maximum clamping force - Strong, reliable pump with high delivery capacity - Optimum multi-sided guidance of the threading agent through the die head exactly to the threading location guarantees clean threads and long service life of the die dies, gear and motor - Only one automatic universal die head for all threads, also long ones; automatically opening - with automatic thread length for tapered threads - Fast, easy adjustment of the thread size - Clear thread scale - Easy and quick change of the die dies thanks to their positioning in the clamping part - Reliable, indestructible, high-quality REMS die dies with optimum geometry guarantee very easy entry into the material, easy threading and clean threads. They are made of load-bearing, specially hardened steel for an exceptionally long service life. - Self-centering pipe cutter. Sturdy frame made of forged steel. Ergonomic, wide handle for strong spindle pressure - Specially hardened cutting wheel made of reliable, tough-hard knife steel ensures long service life. - Internal deburrer, Stable, easy-to-use deburring device with variable deburring position. - Specially hardened and machined blade guarantees easy deburring and exceptionally long service life - Two blades for optimum deburring, especially with small pipe diameters

Year of construction: 1992, condition: ready for operation (used), Application range: large threads, breakage protection: from M3.0, capacity in stainless steel: up to M10, capacity in 9SMn28: up to M10, connected load: 2000W, with automatic Z-axis feed for automation. The machine is fault-free and operational, showing signs of use. With documentation and five holders. An on-site inspection is possible. Isdpfox Hfgpjx Aanetr

Condition: good (used), Thread cutting head with Strehler jaws, thread cutting die, Itodsb A Rfispfx Aanjr Thread cutting machine, pipe thread cutting -inch thread: 1"- 2" inch -Weight: 6.5 kg

Condition: excellent (used), functionality: fully functional, overall weight: 785 kg, total width: 1,015 mm, total length: 1,570 mm, total height: 1,270 mm, type of input current: three-phase, input voltage: 380 V, metric thread diameter (max.): 80 mm, metric thread diameter (min.): 16 mm, thread length: 450 mm, rotational speed (min.): 14 rpm, rotational speed (max.): 94 rpm, metric thread pitch (max.): 6 mm, metric thread pitch (min.): 2 mm, HMV thread cutting machine, type OK-5 Specifications Thread cutting range (Whitworth/UNC) 5/8"- 3" Thread cutting range (BSP) 1/2"- 4" Thread cutting range (Metric) M16-M80 Number of speeds 8 Itedpfx Aaoxz R Huonjr Speeds, rpm 14,20,28, 32, 40, 48, 64, 94 Motor output, hp 2.7 - 4.5 Motor output, kW 2.3 - 3.0 Motor speed, rpm 700 / 1400 Spindle bore, mm 118 Spindle bore, in 4 21/32" Max cutting length without relocation, mm 450 without relocation, in 17 3/4" with relocation infinite Dimensions and weight Overall length, mm 1570 Overall width, mm 1015 Overall height, mm 1270 Height from floor to bed, mm 830 Width of bed, mm 370 Required floor space, mm 1570 x 1015 Bed size (L x W), mm 815 x 580 Net weight, kg 785

Condition: used, Internal threading machine HAGEN & GOEBEL type HG 10 Tapping machine, Vertical tapping machine Machine. No. 4462 Year of construction approx. 1980 Cutting capacity in steel M3 to M10 Cutting capacity in cast iron M3 to M16 Cutting capacity in brass M3 to M18 mm throat depth 250 mm Pinol stroke 80 mm Table size 340 x 240 mm Spindle speed 200-1000 rpm 6 steps Motor power 0.55 and 0.75 kW Mains connection 380 Volt, 50 Hz - 6 speed levels through 2 motor speeds and 3 belt levels - Thread pitch via guide cartridge - 2 guide cartridges with 1.0 mm and 1.25 mm thread pitch - Spindle holder with cone Ø 14.8 to 16 mm and 4 mm keyway - Table height adjustment with toothed rack via hand crank on the round column - Quick-change tapping chuck size 1, Ø 19 mm Space requirement L x W x H 850 x 550 x 1800 mm Weight 255 kg Good condition Itsdpfxjupbf Do Aaner

Year of construction: 2013, condition: new, Various thread rolling tools Manufacturer: Fette see list all tools new ! M12-14x1,5 2/57 1K 1509925 1 M12-14x1.75 2/53 1K 1509970 2 7/16-20UNF T18-63-21.5 1538172 7 M20x1.5 T18-226-14A 1539858 8 M16x1.5 T18-33-21.5 1537459 6 M20x1 T18-158-21.5 1555189 6 11/16-14 US T27-687-31 2178650 6 M8-10x1.25 2/518 0.6K 1509550 2 M8-10x1 2/05 2K 509541 2 M8-10x1.5 2/772 0.3K 1 M8x1.25 T18-0.3-21.5 1536370 15 3/4-16 UNF T27-88-22A 2182703 2 M22x1.5 T27-39-14A 1544067 1 1/2x20 UNF T27-909-10A 2406829 3 3/4/16 UNF T18-67-16A 1538332 4 M12x1.5 T18-30-21.5 1536959 4 7/8-14 UNF T27-89-20A 3 M12x1.25ISO T27vB 31mm 291 5 M8x1.25 T18-03-08A 2175185 7 M8x1.25 T18-03-10A 1536316 1 M8x1 T18-17-21.5 1539787 1 11/16-14UNS T27-687-31 2178979 1 M25x1.5 T27-41-22A 2 M16-18x1 34/363 3K 1517783 4 M24x1 LH T27-29L-31 2179796 3 M24x1 ISO T27 31mm 3 M20x0.5 T18-228-16A 2177355 1 M12x1.25 T18-28-21.5 1536888 2 3/8-24 UNF T18-62-21.5 1538154 2 3/4-16 UNF T18-67-16A 1538332 2 10-32 UNF T18-286-12A 1538056 1 M12x1.5 T18-30-21.5 1536959 1 M18x0.75 T18-186-08A 1537547 3 M8x1 1223/05 1K 1508533 2 M11x0.75 T12-22-12A 2 M12x1 T12-27-15.5 531918 10 M7x0.75 T18-12-21.5 2179611 3 M7x1.0 1 Itsdobv Tg Hopfx Aaner M17.5x0.5 ISO T27vB 31mm 275 1 M16x1 T18-24-20A 1537379 1 M10-12x1.5 2/515 0.6K 1 M16x1 T18-24-21.5 1537388 2 M7x1.0 ISO T18 16mm FormA 5 1/2-20 UNF T27-85-16A 1545761 1 M12x1 T27 1 M18x1.5 T18-35-21.5 1537627 3 13/16x16 2 1/8-28 GAS T18 21mm

Condition: used, Year of construction: 2020, functionality: fully functional, metric thread diameter (min.): 3 mm, metric thread diameter (max.): 12 mm, working range: 1,900 mm, overall weight: 13 kg, rotational speed (max.): 400 rpm, torque: 28 Nm, Tapping Range: M3 - M12 Rotation Speed: 400 rpm Max. motor torque: 28 Nm Air pressure: 6 - 8 bar Working range: 150 - 1900 mm Machine weight: 13 kg Year: 2020 Itjdpfx Aajw Smr Ajner The pneumatically driven thread tapping machine DUMETA D-JSC-12A is designed for thread cutting in the range of M3 to M12. It features a compressed air motor and a quick-change chuck. The sturdy working arm can be mounted directly onto a workbench using the integrated flange. This allows the tap to be positioned flexibly at various locations on the workpiece without the need to reposition the workpiece itself. The design includes an adjustable angle, enabling the quick-change chuck to be tilted, so that both vertical and horizontal tapping operations are possible. Optional: Workbench with dimensions 2210 mm (L) x 940 mm (W) x 820 mm (H).

Condition: excellent (used), Year of construction: 2004, functionality: fully functional, machine/vehicle number: 1028, Thread Rolling Machine LEISTRITZ RT 400-CCA Year of manufacture: 2004 / Control system retrofit in 2019 Connection voltage: 3x400 V Frequency: 50 Hz Rated power: 65 kW Main fuse: 125 A Itsdpfxsxytmhs Aanjr Operating pressure: Air: 6 bar, Oil: 270 bar Control voltage: 24 VDC Maximum shaft length: 275 mm Minimum shaft length: 125 mm Maximum roll set diameter: Tool Ø69.85: 215 mm, Tool Ø80: 210 mm Minimum roll set diameter: Tool Ø69.85: 176-178 mm, Tool Ø80: 176 mm Maximum rolling force: 40 t Space requirement: 3.4 m x 2.9 m x 2.2 m Weight: 4900 kg Accessories: - Coolant filtration system - Second spindle pair (1x for tools Ø69.85 mm, 1x for tools Ø80 mm)

Condition: good (used), Thread cutting head with Strehler jaws, thread cutting die, Iedpfsb A N Uqox Aanjtr Thread cutting machine, pipe thread cutting -inch thread: 1/2"- 2" inch -Packaged: in contact -Weight: 15 kg

Condition: used, Internal threading machine Hagen & Goebel type HG 124 Machine no. No. 4112 Year of construction approx. 1980 Cutting capacity in steel M3 to M10 Cutting capacity in cast iron M3 to M15 Cutting capacity in brass M3 to M17.5 throat depth 250 mm Pinol stroke 80 mm Table size 345 x 245 mm Spindle speed 200 - 1000 rpm Motor power 0.55 / 1.0 kW Mains connection 380 Volt, 50 Hz Itsdpfx Aohgnd Aoaner - 6 speed levels via belt change (3 levels via belt + 2 motor speeds) - Thread pitch via guide cartridge - 2 guide cartridges with 0.8 mm and 28 G per inch thread pitch - Table height adjustment with toothed rack via hand crank on the round column - Spindle holder with cone Ø 14.8 to 16 mm - Gear rim drill chuck Ø 1 to 13 mm Space requirement L x W x H 900 x 500 x 1800 mm Weight 260 kg Good condition

Condition: good (used), Thread cutting head with Strehler jaws, thread cutting die, Thread cutting machine, pipe thread cutting -inch thread: 1"-2" inch Itodpeb A Raaefx Aansr -Weight: 1.5 kg

Condition: good (used), Thread cutting head with Strehler jaws, thread cutting die, Thread cutting machine, pipe thread cutting -inch thread: 1/4"-1 1/2" inch Itjdpfxsb A N U No Aanjr -Weight: 8 kg

Condition: good (used), Thread cutting head with Strehler jaws, thread cutting die, Itjdpfx Asb A Riijanjr Thread cutting machine, pipe thread cutting -inch thread: 1" - 2" inch -Transport crate -Weight: 11 kg

Condition: good (used), Thread cutting head, thread cutting chuck, thread chuck, tap chuck, milling tool, thread cutting apparatus Iodsrvldujpfx Aanjtr -Manufacturer: Pittler, self-opening thread cutting heads 2 pieces -Type: Model A No 3d L485 -Size: M7 x 1.25 1 piece -Size: Ø 24 mm recording MK4 1 piece -Price/tax: complete -Transport dimensions: 180/140/H310 mm -Weight: 8.5 kg

Condition: good (used), Electronically controlled unwinding unit, thread unwinder, yarn winder, thread winder, reel, -Manufacturer: Texmer, Electronically controlled unwinding unit -Type: EGA 2000 EGA-2000-31001271 -Spool weight: max. 40 kg -Quantity: 12x spooling units available, 1x shaft without attachment Price: per piece -Dimensions: 545/255/200 mm -Weight: 13.8 kg/pc. Isdpfxexyv Uhj Aanotr