Used Tying for sale (72)

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, oil tank capacity: 1,300 l, power: 75 kW (101.97 HP), year of last overhaul: 2025, For sale is a overhauled Bollegraaf baler, with 100 tonnes pressing force, large bale format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding system Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors. Bsdjzdn H Rjpfx Amnjli

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2025, volume flow: 410 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Blsdszdnxgepfx Amnei Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2022, condition: used, The lot consists of 2 binding machines. Machine type: KNRA-6/900x1200 Year of manufacture: 2022 Bodjy Tw Tnjpfx Amnsli Additional technical data can be provided upon request. Offers must be submitted for consideration.

Year of construction: 2025, condition: used, functionality: fully functional, Max Rebar Tying Machine RB 443T — Year of manufacture 2025 Used, from the professional rental fleet of Kurt König Baumaschinen GmbH, Einbeck, Germany. Condition & Notes: - Condition: Used, ex-rental, regularly serviced - Functionality: Fully operational - Product photos to follow — please contact us for current images - On-site inspection in 37574 Einbeck available by appointment Price EUR 1,850 plus VAT | EXW Einbeck | Delivery upon request Bjdpfxey A Haio Amnjli

Condition: excellent (used), Year of construction: 2010, Vertical injection molding machine. 3-station rotary table. Screw diameter: 22 mm. Year of manufacture: 2010. Blodolu Hblepfx Amnoi

Year of construction: 2026, operating hours: 24 h, condition: new, Equipment: CE marking, Shoe soles are only roughly cleaned w􀇕th a dry curly hyg􀇕ene mop. For hand d􀇕s􀇕nfect􀇕on, two hands are s􀇕multaneously 􀇕nserted 􀇕nto two separate chambers on the front of the mach􀇕ne, and the solut􀇕on 􀇕s sprayed as soon as the hands are detected by the sensors. There are Red/Green LED warn􀇕ng l􀇕ghts that 􀇕nd􀇕cate that the process has been completed and completed. After the person's hand d􀇕s􀇕nfect􀇕on process, he/she 􀇕s g􀇕ven perm􀇕ss􀇕on to pass through the turnst􀇕le. Dry curly mop for clean􀇕ng shoe soles and d􀇕s􀇕nfect􀇕on of hands are carr􀇕ed out together. IT IS MANUFACTURED FROM 304 CR STAINLESS MATERIAL. A HYGIENE MAT IS AVAILABLE. The Hyg􀇕ene Mat can be eas􀇕ly replaced 􀇕f des􀇕red. It prov􀇕des hyg􀇕ene qu􀇕ckly and e􀇖􀇕c􀇕ently 􀇕n any locat􀇕on needed 􀇕n the fac􀇕l􀇕ty. It 􀇕s eas􀇕ly portable and can be 􀇕nstalled anywhere. A mandatory hand d􀇕s􀇕nfect􀇕on 􀇕s prov􀇕ded for two hands s􀇕multaneously, and the hand d􀇕s􀇕nfect􀇕on t􀇕me can be adjusted. It does not allow one-handed passage. There 􀇕s an adjustable turnst􀇕le lock accord􀇕ng to ex􀇕t d􀇕rect􀇕on and preference, and the turnst􀇕le Blsdpfszg A Emex Amnji durat􀇕on can be adjusted. Approx􀇕mate d􀇕mens􀇕ons 86.5 cm (length) x 60 CM (w􀇕dth) x140 CM (he􀇕ght) 304 CR Sta􀇕nless Steel ra􀇕l􀇕ng 􀇕s ava􀇕lable. FREE PASSAGE WHEN THERE IS NO ELECTRICITY. There are he􀇕ght adjustable legs. There 􀇕s a sta􀇕nless carry􀇕ng plate for d􀇕s􀇕nfectant can􀇕sters on one s􀇕de of the dev􀇕ce. IT OPERATES WITH 220 V ELECTRICITY

Condition: used, Cyklop EMT-AXRO Industrial Elastic Band Tying Machine, Used Machine Manufacturer Cyklop International GmbH (Cologne, Germany) Bodpfx Amjzh Uu Neneli Model EMT-AXRO Technical Specifications Year of Manufacture: 2003 Power Supply: 230 V / 50 Hz Power Consumption: 0.18 kW Overall Dimensions Width: 570 mm Depth: 460 mm Height: 720 mm Weight: 30 kg

Condition: used, Year of construction: 2005, operating hours: 24,500 h, functionality: fully functional, Manufacturer Avermann Bljdszc Rhvspfx Amnoi Typ AVOS 1810S-90/100 Year of construction 2005 Hours of operation 23,100 h Quantity of pressed bales 16,163 piece Press power main press 100 tons Specific press capacity 121,2 N/cm² Feed channel 1,000 x 1,800 mm Capacity per cycle time 1,35 cm³ Theoretic cycle time 12,5 sec. Bale size 1,100 x 750 mm Driving motor 2 x 45 kW Connected load 130 kW Tying system 5 fold vertical, full automatic Throughput rate at a bulk weight of 30 kg/cbm approx. 12,2 tons/h bulk weight of 50 kg/cbm approx. 16,0 tons/h bulk weight of 100 kg/cbm approx. 23,2 tons/h Bale weight 500 up to 800 kg, depends on material and bale length Volume hydraulic oil tank 2,000 l SPS controller (manuf., type) Siemens SIMATIC S7-300 Transport dimensions only baler 11.200 x 2.355 x 2.700 mm (without feeding chute) Machine weight baler approx. 24,5 tons Accessories: ruffler and special press ram

Condition: used, Year of construction: 1993, Location: Malta Presona LP 50 VH Hydraulic Baler Presona LP 50 VH fully automatic horizontal hydraulic baler available for sale. The machine includes a hydraulic power unit, an automatic wire tying system, PLC controls, a pre-press and main press assembly. Suitable for OCC, paper, plastics, and industrial recyclables. Conveyor system not included. Sale Includes: Presona LP 50 VH horizontal baler Hydraulic unit Main press system Pre-press system Friction channel Automatic wire tying system Needle assembly PLC control system Hydraulic power pack Electrical control cabinet Bale ejection system Not Included: Conveyor system Machine Overview Main Technical Specifications Specification Details Manufacturer: Presona AB Model: LP 50 VH Machine Type: Fully Automatic Horizontal Hydraulic Baler Maximum Hydraulic Pressure: 25 MPa Press Force: 500 kN Power Supply: 220–600V AC, 3 Phase Control Voltage: 24V DC PLC Bale Weight: Up to approx. 800 kg Strapping: Automatic Multi-Wire Tying Operation: Continuous Automatic Operation Materials Suitable for Baling: OCC / cardboard, Waste paper, Newspapers & magazines, Plastics, Packaging waste, General recyclable materials Main Features: Hydraulic Pressing System Heavy-duty hydraulic main press Hydraulic pre-press system Adjustable friction channel pressure Continuous compaction operation Automatic Wire Tying Fully automatic multi-wire tying Hydraulic needle assembly Wire twisting and cutting system PLC Controlled Automatic operating cycles Error monitoring system Programmable material settings One-man operation capability Hydraulic Unit: The hydraulic system includes: Bljdozhpa Tjpfx Amnji Hydraulic pumps Oil tank Pressure regulation valves Oil filters Pressure transmitter Oil temperature monitoring Optional systems mentioned in the manual: Oil cooler Oil pre-heater Remote display Automatic Bale Tying System: The LP 50 VH features: Hydraulic needle assembly Automatic wire feeding Automatic twisting and cutting Multi-wire bale securing system Ideal Applications: Recycling facilities Waste transfer stations Cardboard recycling operations Plastic recycling plants Industrial waste processing Distribution & logistics centres Storage location: Customer

Condition: ready for operation (used), Year of construction: 2009, Well-maintained PRESTO HPK 50 BSK automatic horizontal baler in fully operational condition. The machine has been in continuous industrial use and has been regularly serviced and professionally maintained throughout its lifetime. It was recently dismantled from operation due to plant modifications and is ready for transport and immediate recommissioning. Suitable for baling: Cardboard (OCC) Paper Mixed recyclables Plastic films PET bottles Packaging waste The HPK 50 BSK is a compact and reliable industrial baler designed for medium to high throughput operations. Its large feed opening allows efficient loading by conveyor, wheel loader or excavator. The fully automatic wire tying system ensures consistent bale quality and low operating costs. The PRESTO HPK series is well known throughout Europe for durability, simple maintenance and reliable operation. Pressing force: 50 t Motor power: 22 kW Power requirement: 400 V / 80 A Bodpfx Aszcdrnomnoli Feed opening: 1,250 x 1,050 mm Bale dimensions: 1,100 x 700 mm Bale weight: up to approx. 500 kg depending on material Cycle time: approx. 22 sec Throughput: up to 5–10 t/h depending on material density Fully automatic 4-wire tying Machine dimensions: approx. 6,820 x 1,950 x 2,160 mm Machine weight: approx. 8.75 t

Condition: good (used), Year of construction: 2015, functionality: fully functional, Baling press Dixi 60 SLD, year of manufacture 2015 Manufacturer: Dixi Type: Dixi 60 SLD Year of manufacture: 2015 Drive power: 7.5 kW, 400 V / 16.5 A Feed opening: 990 x 1,110 mm (W x L) Pressing force: 60 t Pressing cycle: approx. 47 s Bale size: 800 x 1,100 x 1,200 mm (W x H x L) Bale weight: approx. 370-410 kg Tying: 3-fold, manual Machine dimensions: approx. 4,150 x 1,725 x 2,035 mm (L x W x H) Machine weight: approx. 5,420 kg Materials: Paper, cardboard, film The press is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. The operating manual and CE declaration are available. Bodpfx Amszgvbujneli We will be happy to answer any questions you may have about the machine by telephone from Monday to Thursday from 8:00 a.m. to 2:00 p.m. On Friday, we are available for you from 8:00 a.m. to 1:00 p.m. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided and for any errors. The offer is subject to change, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment ex works, without warranty.

Condition: good (used), Year of construction: 2015, functionality: fully functional, Baling press Dixi 60 SLD, year of manufacture 2015 Manufacturer: Dixi Type: Dixi 60 SLD Year of manufacture: 2015 Drive power: 7.5 kW, 400 V / 16.5 A Feed opening: 990 x 1,110 mm (W x L) Pressing force: 60 t Pressing cycle: approx. 47 s Bale size: 800 x 1,100 x 1,200 mm (W x H x L) Bale weight: approx. 370-410 kg Tying: 3-fold, manual Machine dimensions: approx. 4,150 x 1,725 x 2,035 mm (L x W x H) Machine weight: approx. 5,420 kg Materials: Paper, cardboard, film Bledjy Ni Eujpfx Amnoi The press is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. The operating manual and CE declaration are available. We will be happy to answer any questions you may have about the machine by telephone from Monday to Thursday from 8:00 a.m. to 2:00 p.m. On Friday, we are available for you from 8:00 a.m. to 1:00 p.m. Please note: All technical data refer to the manufacturer's specifications. We assume no liability for the information provided and for any errors. The offer is subject to change, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment ex works, without warranty.

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Bljdey S Rqwspfx Amnei Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,400 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 75 kW (101.97 HP), year of last overhaul: 2025, volume flow: 300 m³/h, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport dimensions 8500 x 2450 x 2950 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see the video for the machine function test. Comments: The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) for the press is available. Bodpfxoy R Nnfs Amnsli

Condition: reconditioned (used), Year of construction: 2015, operating hours: 30,143 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 570 kg, overall weight: 20,000 kg, oil tank capacity: 600 l, power: 37 kW (50.31 HP), year of last overhaul: 2025, volume flow: 800 m³/h, Technical data baler: Manufacturer Presona AB, Sweden Type LP 60 VH1 Year of construction 2015 Total operating hours, 30,143 hours, as of July 2025 Effective pump running time onl 6,527 hours, as of July 2025 Number of pressed bales 115,193 bales, as of July 2025 Press force pre press 25 t Main press force 60 tonnes Specific pressing force 73N/cm² Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Theoretical throughput capacity 800 m³/hour Throughput capacity under operating conditions 350 m³/hour Bale dimensions 1,100 x 750 mm Drive power 37 kW Tying 5-fold vertical, fully automatic Throughput capacity with a Bulk weight of 50 kg/cbm 11 to 14 tonnes/hour Bale weights 420 to 570 kg, depending on material Hydraulic oil tank volume 600 litres Baler dimensions assembled with hopper 10,100 x 3,750 x 4,310 mm (l x w x h) Transport dimensions excluding press 10,100 x 2,400 x 3,000 mm (l x w x h) Machine weight press approx. 20 tonnes Condition of the press: The press was partially overhauled in our workshop and then tested in manual and automatic mode. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Grease cartridges of the automatic roller lubrication system replaced Slide rails cut out from the press floor in the press room Underbody reinforced with welded sheets New HARDOX slide rails welded in Wire station with deflection rollers for the lower wire cleaned and made operational Bljdpjzdny Rsfx Amnsi Slide rails cut out from the floor in the press channel New HARDOX slide rails welded in Both side walls of the press channel dismantled, derusted Worn side wall plates cut out Complete side walls covered with new wear plates and welded Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Machine checked, general maintenance work carried out and press tested in manual and automatic mode Comments: The press is sold without a conveyor belt and without wire stations. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, power: 235 kW (319.51 HP), fuel type: diesel, tire size: 385/65-22,5, axle configuration: 4x2, wheelbase: 3,790 mm, fuel: diesel, fuel tank capacity: 150 l, color: white, driver cabin: day cab, gearing type: automatic, emission class: euro6, suspension: steel-air, loading space length: 42,000 mm, loading space width: 24,200 mm, loading space height: 6,000 mm, Year of construction: 2024, Equipment: ABS, AdBlue, Bluetooth, EBS, air conditioning, central locking, crane, cruise control, differential lock, electric window regulation, electronic stability program (ESP), navigation system, onboard computer, power mirror, seat heater, trailer coupling, - Rear work lights - Heated exterior mirrors - Heated mirrors - Passenger seat - Bluetooth - Automatic climate control - Air-suspended seats - PTO (Power Take-Off) - Radio / multimedia system - Beacon - Reversing camera - Seat heating - Sun visor - Lane departure warning - Stability control - Windscreen (windshield) Internal reference number for customer inquiries: 4-028 MAN TGM 18.320 4x2 BL with PAVIC three-way tipper body and Fassi loading crane Vehicle: MAN TGM 18.320 4X2 BL loader crane tipper Cab CC: The compact cab (narrow, short, standard height) Wheelbase: 3,875 mm Suspension: leaf/air Drive: 4x2 Tyres front axle: 2 x 295/80R22.5, rear axle: 4 x 295/80R22.5 Gross vehicle weight: 18,000 kg Automatic transmission MAN TipMatic 12 12 OD Diesel engine MAN D0836 LFLAP, 235 kW (320 hp) output, 1,250 Nm torque, Euro 6e Transmission functionality: EfficientRoll Cruise control Differential lock on rear axle MAN EasyControl operating panel, 4 functions, operable from outside with door open Trailer coupling RINGFEDER type 4040/G150B Brake connection 2-line at end of frame Sun visor in front of windscreen Central locking with remote control MAN Media System Navigation Advanced 7-inch Heated and electrically adjustable rear and wide-angle mirrors Driver comfort seat, air-suspended, with lumbar support, shoulder adjustment and heating Adjustable seat belt height, driver seat 2 work lights on cab roof 2 halogen beacon lights on cab roof MEILLER axial pump 270/45 Tipper control in cab Blodpfx Ameylx H Senei Body: PAVIC three-way tipping body 4200x2420 mm Front wall height: 800 mm Side board height: 600 mm 8 fully recessed lashing rings in decking (4 per side) Material: Hardox 450 Support for horizontal positioning of the sideboard with rubber pad (for transporting long items) Springs as sideboard lifting aid for easier opening and closing 2 lashing rings on front wall (e.g. for tying down a compactor or grab bucket) Tipper body hot-dip galvanized and all panels etc. fully painted with 2-component truck paint in RAL9016 Subframe galvanized and painted in RAL 9011 Left and right side as one piece, both sides openable by pneumatic system with air valve from the cab; all sides can be opened from below (pendulum system), from top to bottom manually, centre stanchions removable Springs as sideboard lifting aid for easier opening and closing ...and much more Note: Additional body equipment: Pre-prepared positions in the pillars for easy retrofit of a leaf mesh grid (sideboard extensions PLUS 500mm, e.g. for hedge trimmings transport) -> In stock Loader Crane: FASSI F195A.2.24 e-dynamic Lifting moment: 162 kNm (16.51 mt) Hydraulic four-fold extension, 12.7 m outreach E-dynamic hose equipment for 2 additional devices Slewing range: 400° Double linkage with PROLINK (overbending knuckle boom up to 15°) Electronic overload switch-off system with FX 500 FASSI stability control FSC incl. LMB II Fassi RCS radio remote maxi – 6 functions with 3 joysticks (2-2-2) Special outrigger supports, outrigger width 6.64 m, hydraulically extendible incl. FSC Outriggers operable via remote control FL system (Full Lift): engageable fast flow valve for the extensions LED work lights This is a...

Condition: good (used), Year of construction: 2015, operating hours: 1,932 h, functionality: fully functional, Bale press Presto CC 50 M, year of manufacture 2015, with lifting and tilting device. Technical data: Manufacturer: Presto Type: CC 50 M Year of manufacture: 2015 Operating hours: 1932 Pressing force: 50 t Cycle time: 52 s Drive power: 7.5 kW Feed opening: 1030 x 1100 mm Feed volume: 0.85 m³ Tying: 3-wire, manually Throughput at a bulk density of: 35 kg/m³ - 1.3 t 60 kg/m³ - 1.7 t 100 kg/m³ - 2.2 t Bale dimensions: 750 x 1100 mm Bale weight: 300 kg Dimensions: 4705 x 1680 x 2540 mm (L x W x H) Machine weight: approx. 4000 kg Materials: Paper, cardboard, film The operating manual is available in German. Note: The machine is in good condition. It has been inspected and tested at our facility in 28816 Stuhr. You can find the video on our website or our YouTube channel. Blodezc Hz Ejpfx Amnji Please note: All technical data refers to the manufacturer's specifications. We assume no liability for the information provided or any errors. This offer is non-binding, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is made against advance payment, ex works, without any warranty.

Condition: used, Year of construction: 2020, functionality: fully functional, pressing force: 120 t, filling opening width: 2,000 mm, filling opening length: 1,000 mm, bale width: 750 mm, bale height: 1,100 mm, total width: 2,835 mm, total height: 4,374 mm, total length: 19,627 mm, overall weight: 43,000 kg, warranty duration: 12 months, power: 75 kW (101.97 HP), Equipment: documentation/manual, For sale is a baling press, model "HP-G 4 120 VG6," manufactured in 2020, featuring a 6-strand vertical PP twine tying system. The pictures show the machine in its assembled condition. It is now located at our facility in Lathen. The press is sold without a conveyor belt. Before delivery, the machine will be completely overhauled and technically refurbished by our qualified personnel. Our goal is to provide you with a reliable and immediately operational machine that meets the requirements of daily operation. The overhaul includes, among other things, the following services: • Disassembly and inspection of the relevant machine components • Evaluation of all wear-relevant components • Replacement or refurbishment of worn parts • Inspection and repair of the press ram and associated guide elements Bedpfxjzhudqs Amnsli • Inspection and, if necessary, replacement of wear plates, slide guides, and bearing points • Inspection of the press channel and restoration of the required tolerances • Overhaul of the hydraulic components, including cylinders, valve technology, and hydraulic hoses • Replacement of seals, wear parts, and connecting elements • Inspection of the electrical components and safety devices • Inspection and readjustment of the tying device • Cleaning, assembly, and commissioning of the overhauled system • Performance of functional and load tests after completion of the work Thanks to the comprehensive overhaul, you will receive a technically inspected machine with high operational reliability and a long service life. We will be happy to provide you with further information, photos, or a customized offer. If you are interested, we look forward to hearing from you.

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, pressing force: 48 t, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 450 kg, Equipment: documentation/manual, HSM VK 4812 P Year of production: 2017 Fully automatic baler. The device has service and maintenance work by an authorized HSM service with a branch in Germany. Press after significant service work - details after direct contact. The baler comes complete with a ramp for ejection of finished bales and stands for binding wires. Pressing force: 480 kN Drive power: 18 kW Voltage / frequency: 400 V / 50 Hz Capacity at 50 kg/m³: 10.2 t/h Bale width x height x length: 1100 x 750 x 600 - 1200 mm Total length x width x height: 6661 x 3994 x 2583 Machine weight: 10.2 t Compressed material: foil, mixed paper, cardboard, die-cutter waste Bale tying: 4-fold with wire We also have other presses in stock. Transport costs depend on weight, volume and, above all, distance, the following information is important for inquiries: Delivery address (postal code and city name), but further details require telephone contact, so please inquire about transport costs and other delivery methods to contact us contact us by phone. Our contact details can be found in the seller's legal information. We sell and export worldwide, and thanks to our very large storage capacity we can also deliver larger quantities flexibly and quickly. We issue intra-Community invoices - without VAT. opening hours Mon-Fri: 8:00-16:00 Sat: closed Blodpozff Smjfx Amnji

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, pressing force: 80 t, bale weight: 600 kg, Equipment: documentation/manual, DIXI 80 SLD horizontal press Semi-automatic press system with 80 tons of pressure for economical volume reduction of residual materials (recyclable) in industry and retail: Cardboard Tetra packs Films Foams PET bottles Insulating mats and other compressible materials. Bsdpjzd R Evjfx Amnjli Pressure force : 80 t Electrical connection : 400 V 50 Hz; 11 kW; D-32 A (option: K-32 A) Cycle – average approx. : 35 sec Length approx. : 4,320 mm (without lifting device and pallet) Width approx. : 1,830 mm Height approx. : 2,620 mm (with hopper) Loading opening (WxD) – housing : 1,040 x 1,110 mm Bale dimensions : 1,120 x 1,120 x 1,200 mm Bale weight approx. : 500 – 600 kg Tying 4 manual, wires with quick-release eyelets Machine weight approx. 8,000 kg (without bale)

Condition: good (used), Year of construction: 1996, 2 pieces Fab. Hofmann Year of construction 1996 Bale size (channel size)= 80 x 60 cm Bale weight e.g. hay = 220 kg/bale with 1.4 m bale length Hydr. baling pressure = 300 bar Automatic bale tying with 3 wires Ø 3.1 mm Baling capacity approx. 5 t/h Motor power = 18 kW incl. collecting screw under baler incl. electrical control with Wago PLC (year of manufacture 2022) Bodpfortngcox Amnjli undismantled

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,000 kg, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, volume flow: 795 m³/h, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Blsdozbxwiopfx Amnoi Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: used, functionality: fully functional, Year of construction: 2018, machine/vehicle number: 2435618, load capacity: 227 kg, mast type: telescopic, lifting height: 7,920 mm, platform length: 2,130 mm, platform width: 710 mm, overall weight: 1,890 kg, transport length: 2,320 mm, transport width: 840 mm, transport height: 1,910 mm, fuel type: electric, tire size: 16 x 5 x 12, color: red, Technical data Year of manufacture: 2018 Engine: Electric Working height: 9.92 m Platform height: 7.92 m Blodpfx Amsyqy R Njnji Platform dimensions (L x W): 2.13 m x 0.71 m Platform extension: 0.91 m Overall dimensions (L x W x H): 2.32 m x 0.84 m x 2.15 m Weight: 1890 kg Fpjbn N Uju E Ty Tsr N Hec Max. load capacity: 227 kg Max. gradeability: 30% Travel speed: 1.1 - 3.2 km/h Delivery optional Rental optional Fully operational, generally used condition

Condition: used, Year of construction: 2012, operating hours: 53,154 h, functionality: fully functional, pressing force: 120 t, filling opening width: 1,800 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 730 mm, total width: 4,700 mm, total height: 4,600 mm, total length: 13,100 mm, overall weight: 28,000 kg, warranty duration: 12 months, Equipment: documentation/manual, For sale is a bale press, model "EP 1000 V5 H3," manufactured in 2012, featuring both horizontal and vertical tying mechanisms. The pictures show the machine in its assembled state. It is currently located at our facility in Lathen. The press is sold without a conveyor belt. Prior to delivery, the machine will be completely overhauled and technically refurbished by our qualified technicians. Our goal is to provide you with a reliable and immediately operational machine that meets the requirements of daily operation. The overhaul includes, among other things, the following services: • Disassembly and inspection of relevant machine components • Evaluation of all wear-related components • Replacement or refurbishment of worn parts • Inspection and repair of the press ram and associated guide elements • Inspection and, if necessary, replacement of wear plates, sliding guides, and bearing points • Inspection of the press channel and restoration of the required tolerances Bledjzggd Tjpfx Amnoi • Overhaul of hydraulic components, including cylinders, valve technology, and hydraulic hoses • Replacement of seals, wear parts, and fasteners • Inspection of electrical components and safety devices • Inspection and readjustment of the tying mechanism • Cleaning, assembly, and commissioning of the overhauled system • Performance of functional and load tests after completion of the work Through this comprehensive overhaul, you will receive a technically inspected machine with high operational reliability and a long service life. We would be happy to provide you with further information, photos, or a customized offer. If you are interested, please do not hesitate to contact us.

Condition: used, Year of construction: 2010, operating hours: 4,054 h, functionality: fully functional, pressing force: 90 t, filling opening width: 1,450 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 730 mm, total width: 2,500 mm, total height: 3,850 mm, total length: 12,000 mm, overall weight: 23,000 kg, warranty duration: 12 months, power: 90 kW (122.37 HP), Equipment: documentation/manual, For sale is a baling press, model "EP 6100 V5", manufactured in 2010. Prior to delivery, the machine will be completely overhauled and technically refurbished by our qualified personnel. Our goal is to provide you with a reliable and immediately operational machine that meets the requirements of daily operations. Blodpfx Aszggansmnei The overhaul includes, but is not limited to, the following services: • Disassembly and inspection of relevant machine components • Assessment of all wear-related components • Replacement or refurbishment of worn parts • Inspection and repair of the press ram and associated guide elements • Inspection and, if necessary, replacement of wear plates, sliding guides, and bearing points • Inspection of the press channel and restoration of the required tolerances • Overhaul of hydraulic components, including cylinders, valve technology, and hydraulic hoses • Replacement of seals, wear parts, and connecting elements • Inspection of electrical components and safety devices • Inspection and readjustment of the bale tying mechanism • Cleaning, assembly, and commissioning of the overhauled machine • Performance of functional and load tests after completion of the work Thanks to the comprehensive overhaul, you will receive a technically inspected machine with high operational reliability and a long service life. We will be happy to provide you with further information, photos, or a customized offer. If you are interested, we look forward to hearing from you.