Used Tyre Recycling Plant for sale (11,930)

Condition: new, Year of construction: 2025, A sand aggregate production plant is a facility where various types of aggregates (such as sand, gravel, crushed stone, or recycled concrete) are produced for use in construction and other applications. These plants typically include various stages of processing, from raw material extraction to the final product. Here are the key components and processes typically involved in a sand aggregate production plant: Gjdpfoq Ngb Dsx Aabsbu 1. Raw Material Extraction: - Quarrying or Mining: Aggregates are often extracted from quarries, mines, or riverbeds. Depending on the type of aggregate, the extraction process may involve drilling, blasting, or dredging. 2. Primary Crushing: - Jaw Crusher or Gyratory Crusher: The extracted raw material is usually transported to the plant and fed into a primary crusher, where large rocks are broken down into smaller pieces. 3. Secondary Crushing: - Cone Crusher or Impact Crusher: The crushed material from the primary crusher may undergo further reduction in size through secondary crushing. 4. Screening: - Vibrating Screens: After crushing, the material is often screened to separate different sizes of aggregates. This process ensures that the final product meets the required specifications. 5. Washing: - Sand Washers: In some cases, especially for sand production, washing is done to remove impurities, clay, and fines from the aggregates, ensuring a cleaner and higher-quality product. 6. Grading and Sorting: - Classifiers or Graders: After washing and screening, the aggregates may go through additional processes to separate them based on size or quality. 7. Stockpiling: - Stockpiles: The final aggregates are usually stockpiled for storage before being transported to construction sites or other end-users. 8. Aggregate Storage and Handling: - Storage Bins or Silos: Larger production plants may have storage facilities, such as bins or silos, to store different types and sizes of aggregates before distribution. 9. Quality Control: - Laboratory Testing: Regular quality control testing is performed on aggregates to ensure they meet specifications for strength, size, gradation, and other properties. 10. Environmental Considerations: - Water Management: Some plants incorporate water management systems to recycle and reuse water used in the washing process, minimizing environmental impact. 11. Transportation: - Conveyors or Trucks: Aggregates are typically transported from the production plant to construction sites by conveyors, trucks, or other means.

Year of construction: 2024, condition: new, WPS Eddy Current Separator, Magnetic Series. Eddy Current separators from the Magnetic Series are mainly used in the waste recycling industry. The use of eddy currents allows for the recovery of non-ferrous (non-magnetic) metals from loose waste such as aluminium, copper, brass etc. The WPS separators are characterized by high separation accuracy due to the original solutions by ZŁOMIARZE, which guarantees high profitability of waste recycling. WPS Separators are used in the recovery of: • non-ferrous metals from the recycling of electronic waste • non-ferrous metals from car recycling • metals from foundry waste • aluminium in glass recycling processes • non-ferrous metals from steel waste • non-ferrous metals from municipal waste To ensure the longevity of the equipment, the ZŁOMIARZE, as one of few companies, has introduced an improvement in the form of the central cooling of the bearings of the magnetic rotor, thanks to which the service life of the machine has been extended even several times. Technical Specification: • Magnetic field source – NdFeB magnets • Smooth adjustment of magnetic rotor speed – 0-3000 rpm • Belt speed adjustment • Belt position control system • Magnetic rotor cleaning cleats • Belt cleaning scraper • Material divider adjustable in two levels • Bearing cooling system (greatly extends bearing life) • Control panel with safety check For our non-ferrous metal separator we offer additional devices to make you separation process easier: • vibratory feeder Gsdpfxjiqxtbe Aabobu • belt conveyors • magnetic drum/belt separators For more information please download our catalog. If you're interested in our products, please contact us!

Condition: new, Year of construction: 2025, Set of cones(concave + mantle) Maxtrak 1000 Medium Coarse - very good quality. 22%Mn, with SPECTROMETER CERTIFICATE, highest quality on market! Gedpoigvfvjfx Aabsbu Parts number: 603/9052-22 MC + 603/9106

Condition: used, functionality: fully functional, fuel type: electric, Year of construction: 2017, A used stationary 180-300 tons/hour crushing and screening plant suitable for hard and abrasive rock is for sale from FABO. 30 m3 rock feed hopper and feeder 1100x850mm jaw crusher Sandvik CH-440 cone crusher Vsi-900 vertical shaft crusher 2000x6000mm vibrating screen 2200x6000mm vibrating screen Gjdpfjxdbywsx Aabebu On-site conveyor belts Price: €500,000

Condition: used, -Fuel delivery system -Biomass combustion system -Hot water boiler -Ash removal system -Flue gases primary cleaning system -Stairs and service platforms -Draft fan - Automatic control system -Chimney -Circulation system and water treatment Gjdpfswfpwpex Aabsbu Main parameters and guarantee value are calculated according to fuel parameters: -Moisture 60-65 % -Ash till 8 % - Calorific value 7990 kJ/kg and 1907 kcal/kg Main parameters of the furnace 6000 K: - Maximal designed thermal output – 6.5 Mw - Maximum continuous rate – 6 MW - Furnace regulation range 20% - 100% - Volume of furnace- 31.6 m3 - Volume of combustion chamber – 24m3 - Grates area 12 m2 - Grates designed thermal load – 500 Kw/m2 - Combustion chamber designed thermal load – 250 Kw/m3 - Maximum temperature in the combustion chamber - 900°C The following kinds of biomass are accepted for combustion in the furnace: - wood chips – 100% - forest wood residues- 100% - saw dust – 100% (G15) - chunk peat – 100% - bark – 100%

Condition: excellent (used), operating hours: 2,658 h, functionality: fully functional, pressing force: 71 t, filling opening width: 1,000 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, input current: 200 A, oil tank capacity: 1,250 l, empty load weight: 29,000 kg, Technical data baler: Manufacturer BOA Recycling Systems B.V. Type M75-45-A-5-1.6 Ecoline Year of construction 2021 Hours of operation 2,658 hours (as of May 2024) Number of pressed bales 42,212 pieces (as of May 2024) Press power main press 71,2 kN (71 t) Specific press capacity 9 kg/cm² Operating pressure 280 bar Gsdpfx Aasu Thcvsbebu Cylinder stroke 2,200 mm Feed channel 1,620 x 1,000 mm Capacity per cycle time 2,4 m³ Theoretic cycle time 21 seconds Theoretic throughput rate 450 m³/hour Bale size 1,100 x 720 mm, length variably adjustable up to 1,400 mm Driving motor 45 kW Connected load 100 kW Current consumption 200 A Tying system 5-fold vertical, fully automatic, the press stamp is prepared for an additional 3-fold horizontal binding Throughput rate at a bulk weight of 30 kg/cbm approx. 13,6 tons/hour bulk weight of 50 kg/cbm approx. 24,2 tons/hour bulk weight of 100 kg/cbm approx. 36,4 tons/hour bulk weight of 150 kg/cbm approx. 54,7 tons/hour Bale weight up to 600 kg, depends on material Volume hydraulic oil tank 1,250 l SPS controller Siemens S7 1500 Operating panel Siemens SIMATIC HMI TOUCH Transport dimensions of press 10,000 x 2,800 x 3,385 mm (l x w x h) Press height set up with feed chute 4,743 mm Press height with conveyor belt 7,123 mm Machine weight baler approx. 29 tons Noise level <85 dB (A) Condition of the baler: With 2,658 operating hours, the press is almost as good as new and in very good condition, has hardly any signs of wear and is ready for immediate use. Due to larger material input quantities, the pressing force and throughput of the machine no longer meet the customer's current requirements and is therefore being replaced by a new 120 tonne baler. Only the baler is for sale, without conveyor belt and wire drawing stations. Comments: The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2025, Creating a cheap portable or mobile sand making plant involves optimizing costs while maintaining functionality and efficiency. Here's a basic outline of components and considerations for designing a cost-effective portable sand making plant: 1. Portable Sand Making Machine: - Select a cost-effective sand making machine that meets your production requirements. Consider factors like capacity, efficiency, and maintenance costs. - Look for options that offer good performance at a lower initial investment. 2. Screening Equipment: - Choose a portable screening unit to separate the sand into different sizes. This is crucial for producing high-quality sand with the desired particle size distribution. - Consider modular screening units that are easy to transport and set up. Godpfx Aajq N Ud Ijbjbu 3. Conveyor Systems: - Utilize conveyors to transport raw materials between different components of the plant. Opt for simple and reliable conveyor systems. - Explore cost-effective conveyor options that are easy to maintain. 4. Hopper and Feeder: - Incorporate a hopper and feeder system to ensure a continuous flow of raw materials to the sand making machine. This helps optimize the production process. - Choose a design that minimizes material spillage and wastage. 5. Power Source: - Consider energy-efficient power sources to reduce operational costs. This could include using generators or connecting to the electrical grid, depending on the availability and cost of electricity in your location. 6. Chassis and Mobility: - Opt for a simple and robust chassis design that allows for easy transportation. Depending on your needs, choose between wheels or tracks for mobility. - Aim for a design that facilitates quick setup and dismantling to save time and labor costs. 7. Control System: - Implement a user-friendly control system that enables operators to monitor and adjust the sand making process efficiently. - Consider automation features that enhance control and reduce the need for constant manual intervention. 8. Dust Control and Environmental Considerations: - Integrate effective dust control measures to comply with environmental regulations and ensure a safe working environment. - Explore environmentally friendly features to align with sustainability goals. 9. Modular Design: - Consider a modular design for easy customization and scalability. This allows you to adapt the plant to varying production needs over time. 10. Used Equipment: - Explore the possibility of using refurbished or used equipment to cut down on initial costs. Ensure that the used equipment is in good working condition and can meet your production requirements. Remember that while cost optimization is important, it's crucial to maintain the quality and efficiency of the sand making process. Additionally, compliance with environmental regulations should be a priority. Always consider the specific requirements of your project and seek professional advice if needed.

Year of construction: 2024, condition: new, ZIGZAG air separators Application description: ZIGZAG type air separator is a device designed to purify materials in the waste recycling process. The separator separates light fractions from heavy fractions by pneumatic method. It works well with a wide range of waste materials of 0-150mm size. Air separators of this type are used for pre-ground, jagged or very fine materials. Thanks to our unique design, the separator has the ability to adjust at many points that are important for the purity of the received fractions. ZIGZAG type separators are used in many areas: weight classification of metal granules purification of shredded scrap from the light fraction (films, plastics, paper) removal of volatile fraction during recycling of WEEE purification of plastics, rubber purification of municipal waste, glass removal of dust Gbjdpfoua D Aljx Aabou Construction description: The ZIGZAG separator consists of individual components mounted on a common support structure. In the first part, the ZIGZAG module is installed. The module has an inspection hole and regulation of the material stream passage gap. In the second part there is a cyclone discharging the light fraction. Underneath the cyclone there is a variable speed sluice for ejection of separated materials. A fan with electronic speed control is located on top of the structure. The structure is designed in part for loading and unloading by conveyor belts. The separator has a control cabinet equipped with a safety system.

Year of construction: 2025, condition: new, Overband magnet Length: 2500 mm Height: około 400 mm Width: 1000 mm Belt width: 750 mm Magnet width: 500 mm Magnet length: 1044 mm Power: 1,5 kW(hydraulic or electric) Magnet field: 400 Gauss(may catch 100 mm pieces from maximum distance 300 mm Gedpfeh U R Tgjx Aabobu Overband new, 12 months warrenty,

Condition: new, Year of construction: 2025, functionality: fully functional, FTS 15-60 is a compact and heavy steel structured trucked plant with three-decks screen. Also integrated with tracked moving system and robust structure. Works via conveyor belt system. The fully electrically driven plant is designed in a variety for maximum capacities and suitable for feeding materials with a maximum edge length of 200 mm. All functions, as well as subsequent and previous crushing plants, conveyor belts, etc. are electrically lockable. • Production capacity: 500-600 TPH Gbjdpfx Aajxb Db Eobsu • Screen dimension: 1550x6100mm • Mobile three-decks screen • Diesel electric drive • Classifier screen plant up to 4 final fraction sizes Maximum feeding size 100 x 160 mm

Year of construction: 2025, condition: new, To sieve dry material: like flour-, grainy-, and granule-shaped material. Sizes from: wide 500-1500mm / length 1200-2400mm Gedpfjchb Ryjx Aabebu Sieve layers: 2 - 4 layers, granulation 0,1-18mm freely selectable.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors. Gbsdpjvf E Avjfx Aabeu

Condition: new, Year of construction: 2025, STATIONARY CONCRETE BATCHING PLANT S130-TWN GENERAL Plant Type : Stationary Concrete Plant with TWIN Shaft Mixer Plant Capacity : 130m³/hour freshly compressed concrete Mixer Capacity : 4500/3000 lt (3m³ Compressed Concrete) Total Motor Power : 168kw Standard Value can be changed depending on Equipment.. Voltage/Frequency : 380V/50Hz Standard Value. Gsdpfoflz Idox Aabsbu The installation and startup of the plant is under our responsibility. We provide excellent after-sales service. 24/7 SERVICES. REMOTE CONTROL SERVICE. Exporting more than 1000 Concrete Batching Plants to more than 90 Countries all over the world. * HIGHLY EFFICIENT AND DUPLICATE PRODUCTION * EASY MAINTENANCE * SUITABLE TO WORK UNDER HARD CONDITIONS * ABLE TO PRODUCE RCC CONCRETE DETAILS: Compacted concrete capacity : 130 m³/h Air Compressor Capacity : 1300 lt/min Aggregate Hopper : 4 Bins:4×30 = 120m³ Mixer Type : TWIN Shaft (3m³). 4500/3000 lt capacity Aggregate Conveyor Band : 1000 mm * 32000 mm Weighbridges: Aggregate/ Cement /Water/ Additives OPTIONS: *Cement Silo: 75-100-150-200-500 tons *Cement Silo Equipment and Screw Conveyor. Central Lubrication System Brand : ILC (made in italy) Mixer body Plates : Manganese (it can manufacture 50.000m3-450.000m3) Mixer Internal Linings (Wear Plates) : Ni- hard special hard cast material Discharging in Emergency Situations : manual Emergency Situation hand pump Emergency Stop Button available. Digital Mixer Control System (alarm) Automatic lubrication system monitor feature on pc Control System: Full automatic pc - plc – printer. Unlimited users Remote access Unlimited prescriptions and customer registration Retrospective reporting English- Russian- French- Arabic-German-Spanish languages are available. Switching materials used in the MCC dashboard are SIEMENS Back off available.

Condition: new, Year of construction: 2025, In stock: The STF 3.0 floating sink separator with our highly efficient SP1000 Mk2 centrifuge and our VS1 water screen. A compact but powerful washing system that is low-maintenance and can wash/sort up to 3000 kg/h of hard plastics. The machines are made entirely of 304 stainless steel, so salt solutions can be used without any problems. An excellent starting point for a good homemade zinc float installation. Gjdpsxhf Nwsfx Aabobu The machines are in stock and can therefore be delivered within a week. Ask us for further information.

Condition: like new (used), Year of construction: 2022, functionality: fully functional, Complete hydrogen pilot plant: electrical and automation systems for sale. The equipment is fully mounted and has been operational on-site. Gjdpoxixtlefx Aabjbu Mechanical parts also for sale in seperate ad.

Condition: new, functionality: fully functional, fuel type: electric, color: green, Year of construction: 2025, *All of our products are made with care and covered for 1 year warranty! *Installation and Operator Training FREE COMPACT series Stationary Concrete Batching Plants provide satisfaction of all levels need with practical and effective solutions. Stationary concrete batching plants can easily and efficiently reach high capacity production of homogeneous concrete mixture. COMPACT series have easy operating system and lowest investment costs. In addition, the plant provides the use of enterprise resources accurately, so that gaining time-saving will transform to more earnings. . TECHNICAL SPECIFICATIONS: Model: COMPACT 110 Production capacity: 100 m3 Mixer type: Twinshaft – 2 m3 Aggragate bunker: 4x20 m3 Cement weighing: 900 kg Additives weighing: 40 kg Water weighing: 700 lt Cement silo is optional. COMPACT 110 consist of: • Aggregate Storage Hopper • Aggregate Weighing Hopper • Aggregate Transfer Conveyor or Bucket System • Twinshaft Mixer • Mixer Chassis, Walking Platforms, Ladder • Water Weighing Hopper • Cement Weighing Hopper • Admixture Weighing Hopper • Air Compressor • Cement Screw Conveyor Godpfxjxb A E No Aabsbu • Bolted Cement Silo • Top Filter, Safety Valve and Accessories • Control Cabinnet • PC and Automation System • Control and Power Panel FOR FURTHER INFORMATION PLEASE FEEL FREE TO CALL US!!!

Year of construction: 2025, condition: new, Circle Sievemachine to sieve dry material: like flour-, grainy-, and granule-shaped material. Gedsbcngijpfx Aabsbu Sizes from: wide 500-1500mm / length 1200-2400mm Sieve layers: 2 - 4 ply, granlulation < 18mm freely selectable.

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, Technical data on the EPS (Polystyrene) press: Manufacturer FZ-Recycling GmbH & Co. KG, Germany Type FZR 320 Gedpfxou Thkao Aabsbu Year of construction 12/2022 Drive power shredder 4 kW Drive power of compactor screw 7.5 kW Drive power hydraulic unit for the holding clamp in the press channel 1.1 kW Total connected load 12.6 kW Current consumption 32 A Compaction ratio of the compacted blocks to the original product approx. 50:1 (depending on material) Block weight after compaction approx. 300kg/m³ (depending on material) Block dimensions 320 x 320 mm, variable length Throughput approx. 100 kg/hour, depending on material Achievable density approx. 250 - 300 kg/m³ The pressed blocks are stacked approx. 1400 mm high on pallets and stretch-wrapped. Machine dimensions approx. 4,600 x 1,400 x 1,980 mm (l x w x h) Transport weight press 1,325 kg Condition of the baler: The press was only used sporadically, is in very good condition and available at short notice. Due to the low weight of the machine and the forklift shoes in the transport frame, the press is mobile and can be used directly on the construction site where the material is produced. The electrical connection is made via a CEE 32 A plug. Scope of delivery for the baler: 1 piece EPS press, ready for connection and use Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Technical details: load capacity: 800 t Gjdpfjv A Uziox Aabobu total wight: 12,0 / 8,6 t voltage: 380/440 V dimensions L x W x H: 6,9 x1,5 x1,8 m dimension L-W-H: 5,8 x 1,25 x 1,25 m Welding positioner 1x mounting bracket with integrated electric cabinet driven 1x rotating mounting bracket Running speed infinitely variable via frequency inverter Clockwise/anticlockwise rotation *

Condition: new, Year of construction: 2025, In stock: The STF 3.0 floating sink separator with our highly efficient SP1000 Mk2 centrifuge and our VS1 water screen. A compact but powerful washing system that is low-maintenance and can wash/sort up to 3000 kg/h of hard plastics. Gbjdpfx Aajxhf H Njbou The machines are made entirely of 304 stainless steel, so salt solutions can be used without any problems. An excellent starting point for a good homemade zinc float installation. The machines are in stock and can therefore be delivered within a week. Ask us for further information.

Condition: good (used), functionality: fully functional, Year of construction: 2016, operating hours: 500 h, Bunker dosing belt by R&T Recycling Technik Year of manufacture: 2016 Capacity: 2.5 m³ Drive: 1.5 kW Frequency-controlled feed belt Gjdpfx Aaexcuvijbebu This system was integrated into a small pilot plant for approximately 3 months in 2016. The unit is in excellent condition and ready for operation. As shown in photo no. ..., this unit can be transported on a large tandem car trailer.

Condition: new, functionality: fully functional, Year of construction: 2025, The bunker of the PRO-150 Mobile crushers has been developed by our engineers as user-oriented to operate with high-level efficiency. The vibration speed of the vibrating feeding bunker is easily guided by the automation system which can be adjusted manually. This feature prevents the bunker from wearing out and provides the user with longer and more efficient usage. In order to avoid any performance loss due to the damp or muddy material processed in the crusher plants, the wobbler feeder contains all the necessary qualities. While the wobbler feeder has potential to process without any problems for many years. Aslo stands out with easy maintenance feature as well. The poor quality of material separated in the wobbler feeder is thrown into the bypass belt and therefore user get a high-quality final product. Additionally; if desires, the materials falling into the bypass can be sent directly to the screen thanks to the reversible conveyor in the bypass system under the wobbler feeder. FABO primary impact crushers are designed to crush soft and medium hard stones with high rotor speed. It is considered as the heart of the mobile system. With the help of high-speed rotating rotor crushing hammers, the products poured from the feeder are crushed with the help of pallets. Hydraulically adjustable rods allow the products to be obtained in the desired size. FABO folding type hydraulic belts send the right product to the crusher and the stock area according to customer requests after sorting through the vibrating screen. With foldable structure, the plant minimizes dimensions of the machine for the transportation. The number of stock belts can change due to customer requests. Gbodpfow E Iflox Aabsu 10 mm EP 125 4-ply belt elastics moving on twisted sheets perfectly transport the aggregate coming out of the screen to the area desired by the user. Belt elasticity, which produced resistant to wear, offers many years of life without letting customer down. The flap system is a special system that allows the directly crushed material to be taken from the crusher with the help of the pre-stock belt without being screened in the mesh. The plant minimizes production time with its unique location just in front of the screen.

Year of construction: 2025, condition: new, Circle Sievemachine to sieve dry material: like flour-, grainy-, and granule-shaped material. Sizes from: wide 500-1500mm / length 1200-2400mm Sieve layers: 2 - 4 ply, granlulation 0,1-18mm freely. selectable. Gjdpfx Aajbcnatebobu

Condition: excellent (used), Year of construction: 2004, operating hours: 34,480 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 19,000 kg, transport height: 3,300 mm, oil tank capacity: 750 l, power: 45 kW (61.18 HP), Technical data baler: Manufacturer Bollegraaf Gsdpjxbgnhefx Aabobu Typ HBK 100 Year of construction 2004 Hours of operation 34,480 hours Press power main press 100 tons Press power of pre-press max. 42 tons Feed channel 1,600 x 1,100 mm Filling volume 3.15 m³ Theoretic cycle time 22 sec. Theoretic throughput capacity up to 450 m³/hour Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical, fully automatic Throughput rate at a bulk weight of 30 kg/cbm approx. 13 tons/hour bulk weight of 50 kg/cbm approx. 20 tons/hour bulk weight of 100 kg/cbm approx. 30 tons/hour Throughput rate with ruffler approx. 20 tons/hour Bale weight 550 up to 750 kg, depends on material Volume hydraulic oil tank 750 l SPS controller Telemecanique TSX Micro Transport dimensions only baler 10,900 x 2,320 x 3,300 mm (l x w x h) Machine weight baler approx. 19 tons Comments: Unlike the standard HBC press series from Bollegraaf, this machine does not have a pre-press flap but cuts the material between blades on the press ram and the counter blade in the frame. This makes it a cutting edge press, similar to a Paal, unoTech, etc. The press is in very good condition for its age, as it was used exclusively for compressing paper from document destruction. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2025, *All of our products are made with care and covered for 1 year warranty! *Installation and Operator Training FREE FABO manufactures and installs stationary type stone screening & washing plants according to customer requirements. Production capacity of our stationary plants differs from 100 to 1000 ton per hour. 150-250 Tons/hour capacity of Washing and Screening Plant: - Riverstone Feeding Bunker - 2000x6000x4 Decks Vibrating Screen with washing system - 800x8000mm Screw Washer - Conveyor Belt System - Control Panel and Automation System Gjdpfxovdptvo Aabebu FOR FURTHER INFORMATION PLEASE FEEL FREE TO CALL US!!!