Used Water Pumps Germany for sale (24,736)

Condition: good (used), Year of construction: 2012, operating hours: 12,078 h, functionality: fully functional, pressing force: 88 t, filling opening width: 1,100 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 750 kg, overall weight: 30,000 kg, oil tank capacity: 2,000 l, power: 98 kW (133.24 HP), volume flow: 643 m³/h, Technical data baler: Manufacturer HSM GmbH + Co. KG, Germany Type VK 8818 R-FU Year of construction 2012 Total operating hours: 12,078 hours, as of September 2025 Pump operating hours 6,616 hours (effective pump running time) Number of bales pressed: 65,792 bales, as of September 2025 Main press force 880 kN Specific pressing force 120 N/cm² Pressing force cutting edges free rammer 120 kN Dimensions of feed chute 970 x 1,800 mm Theoretical cycle time in idle mode 8.3 seconds Theoretical throughput capacity 643 m³/hour Bale dimensions 1,100 x 750 mm, the length is variable 600 up to 2000 mm Drive power 2 x 45 kW frequency-controlled Connected load 98 kW Total current consumption 192 A Fuse protection 250 A slow-blow 5-fold horizontal tying, fully automatic Throughput rates with a bulk density of 20 kg/cbm 12.86 t/hour Bulk weight of 50 kg/cbm 32.15 t/hour Bale weights with a bale length of approx. 1.2 m 650 up to 750 kg/bale, depends on materiel Hydraulic oil tank capacity 2000 litres PLC control Siemens S7-300 Siemens TP 700 control panel Press dimensions assembled 18,000 x 4,300 x 3.270 mm (l x w x h) Press dimensions with conveyor system 18,000 x 22,000 x 5,765 mm (l x w x h) Transport weight baler approx 30 t (Main press approx. 20 t, press channel with bale clamp approx. 10 t) Special machine equipment: Access locking by means of key transfer system Electro-hydraulic locking of the press carriage during the tying process so that the press plunger does not change position with highly expansive materials Additional optional equipment ordered: Frequency-controlled main drive, 2 x 45 kW, with up to 40 % energy savings compared to the standard motorisation 2 x 45 kW, with the same power output Manual switch-off or switch-on of the number of strapping wires to save on strapping wire for non-expansive material Cutting-edge frei rammer with 121 kN pressing force Sensory wire monitoring, with press switch-off in the event of wire breakage or wire end Bale chute Visual warning signal, mounted on the control cabinet Condition of the baler: The entire baling system (baler and conveyor belt) is in good, operational condition. Technical data for the chain belt conveyor: Manufacturer Stadler Anlagenbau GmbH Typ chain belt conveyor KF 1800 Fgjdpsxcngnefx Aabsh Year of construction 2012 Drive power 7.5 kW Belt speed 0.05 – 0.4 m/second Length of feeding conveyor 6,000 mm Height of side wall from feeding conveyor 400 mm Length of incline conveyor 9,000 mm Height of side wall from incline conveyor 800 mm Length of gooseneck 1,500 mm Incline 30° Nominal width 1,800 mm Useful width 1,700 mm Belt quality EP-500/4 Steel cleats on the rubber belt 50 x 50 mm Hollow pin chain, pitch 125 mm, rollers 36 mm Height of drive axle above ground 4,284 mm Overall height of conveyor belt 5,765 mm Transport dimensions of feeding conveyor approx. 7,000 x 2,200 x 1,250 mm (l x w x h) Transport dimensions of the incline conveyor 13,000 x 2,500 x 2,900 mm (l x w x h) Pit dimensions for the conveyor belt 14,765 x 3,260 x 1,250 (l x w x h) Scope of delivery: The conveyor belt, baling press with bale chute, and wire drawing stations are available for sale, but without the wire. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, machine/vehicle number: NC3015, repeat accuracy: 0.01 mm, travel distance X-axis: 2,550 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 200 mm, positioning accuracy: 0.01 mm, type of input current: three-phase, input voltage: 400 V, table length: 1,500 mm, table width: 3,000 mm, pressure: 3,800 bar, water pressure: 3,800 bar, Equipment: safety light barrier, Complete water jet machine water jet Sweden 3015. Made in 2007 and have been in use since then. Serviced by water jet sweden all the time. Sheet size 3000x1500 mm. Fanuc cnc. Kmt 50 hp pump in excellent condition with a lot of spare parts. 200 L sand hopper and a sand container for 1000 kg. Unit for cutting under water is also included. The machine is in very good condition. It is emptied and we can load it on a truck. Please ask if you want more pictures or if you have other questions. We can also put you in contact with water jet Sweden who has maintained the machine and know all about it. Fgodpfew Sl Ezjx Aabeh

Condition: good (used), Year of construction: 2004, CNC lathe IRLE - IWDS 1000 CNC MACH-ID 7758 Make: IRLE Type: IWDS 1000 CNC Control: SIEMENS 840D Year: 2004 Double carriage with 4 position revolver and 840D Siemens Steady rest 200 - 1090 mm Roller rest 860 - 1090 mm 4 chuck 1350 mm Clamping from 200 - 1100 mm Bed width 2000 mm Stoke X Axis 950 mm Stroke Z Axis 14900 mm Specifications Metric US Standard Swing over bed Ø 1400 mm Swing over cross slide Ø 1100 mm DBC Turning Length 13000 mm Spindle power 129 kW Workpiece weight 20000 Speeds / ranges 1 - 300 Rpm Feed rate X-Axis 4500 mm/min. Feed rate Z-Axis 4500 mm/min. Fgsdpfopdp N Iox Aabsh Dimensions (Estimate) Length 20000 mm Width 3380 mm Height 2200 mm Weight 100000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: like new (used), Baktec water Dosing machine and chiller In good working condition for more information please sent an request Fgsdpfx Aaoump Axjbjh

Condition: excellent (used), For sale: a robust measuring device from the renowned German manufacturer AbaWerk Aschaffenburg. Made with a cast iron base and equipped with two hardened centering points for securing shafts and cylindrical workpieces. Perfect for use with toolmaker’s microscopes, measuring projectors, and in quality control applications. Technical specifications: Fjdpsw Sav Iefx Aabsgh • Manufacturer: AbaWerk Aschaffenburg (Made in Germany) • Center distance: approx. 115 mm • Stable, heavy cast iron base – secure clamping • Allows rotation of the workpiece between centers • Condition: used, fully functional Manufactured to industrial standards – precision and durability make these units highly sought after in metrology and toolmaking environments.

Condition: new, Year of construction: 2023, New, never used collapsible 10.000 gallon (37,854 liter) water or fuel storage with all accessories and documents. Fjdpfx Aexcgagoabogh Located locally in Hungary (EU), Vacegres.

Condition: used, Year of construction: 2009, operating hours: 18,640 h, functionality: fully functional, machine/vehicle number: M15305015, table length: 3,000 mm, table width: 1,500 mm, For sale: MAXIEM 1530 Fgjdpfx Asxcm Svjabeh Single owner from new Machine operational after service Operating hours: 18,640 h Regularly serviced, in continuous use (testing possible) Net price: PLN 139,000.00 Gross price: PLN 170,970.00 negotiable Price includes water treatment unit, machine dismantling, and loading We have a service technician who can install the machine and provide training (costs borne by the buyer)

Condition: used, This listing is for the Grant GD120 Water Bath/Circulator The unit is in full working condition and is ready for immediate use The Grant GD120 is a digitally controlled stirred water bath and circulator ideal for laboratory use, offering high precision and flexibility. Here's a breakdown of its features and capabilities: Key Features Immersion Thermostat with Intelligent Control Optimisation (ICO): Enables adaptive PID control for exceptionally stable temperature regulation. Integral Pump: Built-in circulation pump with a maximum flow rate of 17 L/min, allowing both sample immersion and external fluid circulation. User Interface: Equipped with a clear digital display, a rotor plus two-key control, timer function for reaction timing, and visual + audible alarms to notify operators of critical conditions. Preset Temperature Control: Supports one adjustable operating setpoint plus three preset temperature options for fast switching. Safety Features: Includes float-switch low liquid protection and an adjustable over-temperature cut-out for sample and user safety. Liquid Type Selection: Automatically adjusts heater power and temperature parameters depending on chosen liquid (e.g., water, oil, glycol mixtures). Temperature Range & Accuracy Plastic Tanks (P-series): From around ambient +5 °C up to ~99 °C. Stainless Steel Tanks (S-series): From –15 °C up to ~120 °C. High Stability: ±0.02 °C for stable temperature control. Technical Specifications & Obsolescence The GD120 series includes multiple tank sizes: plastic tanks (P5, P12, P18) and stainless steel tanks (S5, S12, S18, S26, S38), offering varied capacities for different lab needs. This series is now considered obsolete, though it remains functional and reliable for many applications. Supporting Documentation & Manual Operating Manual: The GD120 is covered by the general purpose stirred thermostatic baths manual (shared with GD100), outlining temperature settings, calibration procedures, safety guidance, and maintenance. Fodpfx Aaexhfl Ejbogh Datasheet Summary: Positioned within the broader Grant Optima product range, the GD120 sits between simpler (GD100, up to 100 °C) and higher-spec models (GR150 up to 150 °C, GP200 up to 200 °C)

Condition: like new (used), Year of construction: 2021, Warranty 12 months - Max. temp.: 250°C - Interior (W x D x H): 1600 x 1200 x 1700 mm - Capacity: 3,264 liters - With drive-in rails - Jumo Dicon touch Fjdpfx Aaowktiysbsgh - Equipped with exhaust fan - Net weight: 1850 kg - IP rating: 20 - Power: 29.5 kW - Documentation included We are happy to offer installation and commissioning on request. Inspection at our warehouse by appointment only. We offer new and used industrial ovens. Please contact us! Oven, ovens, drying oven, kiln, heat oven, heating cabinet, industrial oven, tempering oven, warming oven, temperature oven, drying cabinet, chamber oven, curing oven, recirculating drying cabinet, recirculating oven, solvent oven, paint dryer

Condition: used, Year of construction: 1980, functionality: fully functional, travel distance X-axis: 800 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 500 mm, overall weight: 3,000 kg, input voltage: 400 V, Milling machine with Heidemann control and for conventional milling. Equipped with rotary table and tilting table. Fgodpjxfbvbjfx Aaboh

Condition: excellent (used), For sale: professional tool holder from the renowned brand WNT Germany – model B40 ER16M A=100. The holder is equipped with a Centro-P Germany HPC16MS-DI precision collet, ensuring maximum accuracy and clamping stability. The set also includes a VHM drill, making it ready for immediate use on a CNC machine. Condition: very good, the holder is fully functional, no play, with normal signs of use. Premium-class equipment – ideal for professional machining centers where precision and reliability are crucial. Fsdpow Rr A Defx Aabogh

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, machine/vehicle number: 95521, Water Jet Sweden NCP 4020 D Year of manufacture: 2009 1.1 TECHNICAL DATA 1 x Water Jet Cutting Machine, NC 4020 D 1 x FANUC 310iA control unit 1 x IGEMS CAD/CAM software 2 x Fixed cutting heads for AWJ abrasive waterjet cutting 2 x SM3000 feed units 1 x KMT Jetline, 50 HP, 3.8 l/min, 4100 bar 1 x Cooling unit & control cabinet 1 x Hose reel with spray nozzle 1 x Tool kit 1 x Machine safety enclosure 1 x PanelOne HMI "EDGECUT" operator interface 1 x Remote control for high-pressure pump 1 x Remote maintenance 2 x Diaphragm pump and extraction units 1 x Waste container, 1000 l 1 x Pressure vessel, 200 l, and 1-ton online abrasive conveyor/online abrasive container 1 x Starter hole drilling unit 1 x MPG, portable manual control unit 1.1.1 MACHINE DATA Table dimensions (W x D): 4200 x 2275 mm - Cutting area (W x D): 3980 x 2010 mm - X-axis travel (2D): 3530 mm - Y-axis travel (2D): 2010 mm - Z-axis travel: 250 mm - Positioning accuracy (X/Y): +/- 0.050 mm/m - Repeatability (X/Y): +/- 0.025 mm - Rapid traverse X: 30,000 mm/min - Rapid traverse Y: 15,000 mm/min - Rapid traverse Z: 5,000 mm/min - Minimum distance between nozzles: 450 mm - Maximum distance between nozzles: 2010 mm Fgjdpfx Aow Snybeabjh 1.2 CONNECTION DATA 1.2.1 MACHINE CONNECTION • Electrical connection: 3 x 400 V + PE, 16 A, 50 Hz • Pneumatic supply volume (incl. pressure vessel): 500 l/min • Pneumatic supply pressure: min. 6.5 bar 1.2.2 HP PUMP DATA/CONNECTION HP pump data: - KMT 50, Jetline, 4100 bar - 37 kW, circuit breaker at 400/50 Hz, 80 A CAD/CAM software: - IGEMS

Year of construction: 1995, condition: refurbished (used), Wire mechanical descailer with brushes and dust collector Fsdohz T Rxepfx Aabegh Made in Germany YOM - 1995. FULLY REFURBISHED... LIKE A NEW !!!

Condition: excellent (used), Item: D-10800-BacTerminator BacTerminator BTM10FD11001 Water Disinfection Equipment Inclusive pumps, Control and other accessories. Nice condition Fgjdpfjh Dxqvex Aaboh

Condition: like new (used), Year of construction: 2009, functionality: fully functional, machine/vehicle number: 06120006957-98170 001, Brinkmann pump, 160 L/min. As new, Fgodpfx Asw T Sufsaboh

Year of construction: 2009, operating hours: 12,000 h, condition: like new (used), The machine is in excellent condition and reliably cleans the exhaust air (even from several machines). thruput 2400m3 / hour. Fedpofmy D Ajfx Aabsgh

Condition: good (used), Manufacturer : Flygt Type : 2101 Overall dimensions : 650 x 490 x 790 mm Fgedpfxjt H Nc Es Aabjh Electrical data : 400 V; 80 A; 32 KW; 2000 rpm Lifting height : 20 m Weight : 100 kg

Condition: used, Rain gutter, downpipe and elbow forming machines, complete line. Three machines. 1. Rain gutter forming machine, strip cutting with band saw. Produced gutter diameter: 80 x 100 mm Used sheet metal dimensions: Width: 350 mm. Thickness: 0.43 – 0.55 mm. 2. Downpipe forming machine, can form 127 mm and 152 mm (standard) sizes. Cutting with guillotine. Used sheet metal dimensions: Width: 300 mm. Thickness: 0.43 – 0.55 mm. 3. Elbow forming machine: 400V/3 Fgodpfxsv Evctj Aabsh If you have any further questions, we will be happy to answer them.

Year of construction: 1998, condition: as good as new (ex-display), Wire chemical treatment cleaning unit FULLY refurbished with ALL brand new parts except chassis. Please contact us for more details. Thank you! Fgodpfx Ajfhw Uyjabjh

Condition: new, Features > 5-axis simultaneous CNC machine > Basic structure made of polymer concrete > Wet/dry machining > Workpiece zero-point clamping system > Servo drives with absolute encoder > Integrated control with touchscreen Options > Machine base frame > Various Zero-point clamping devices: T-slotted plate, four-jaw chuck, precision vice and blank holder Fgedpfxehqhkis Aaboh > Automatic placement system > 3D measuring probe > Why buy? Simply finance. Talk to us! The iMG 1010 is a compact solution for processing workpieces up to 100x100x100 mm. With its basic structure made of polymer concrete, it enables precise processing of numerous materials such as titanium, steel, CoCr, ceramics, sapphire, zirconium or aluminum. Particularly noteworthy is the arrangement of the Y-axis, which ensures high stability and enormous vibration damping thanks to its installation positions. Almost all positions on the workpiece can be reached without reclamping. The selection of workpiece clamping devices and holders in conjunction with the zero-point clamping system makes the machine a versatile machining center. Its design enables wet/dry machining without time-consuming retooling. The CNC machine can be extended with an optional loading and unloading system, which accesses the machine room from the right, left or from above. This allows workpieces to be changed automatically. The zero-point clamping system serves as an interface and ensures the exact and repeatable positioning of the workpiece. The system can be integrated into network-controlled, automated production processes using software interfaces. The maintenance-friendly design and the long-lasting direct spindle drives save service costs and time and offer a reliable machining system. During the design phase, care was taken to ensure that all elements are easily accessible and yet protected from external influences in order to guarantee a long service life. The sophisticated system offers numerous options for expansion.

Year of construction: 1995, condition: refurbished (used), Mechanical descailer with brushes and dust collecting unit Made in Germany Fgedpfogi N Nnsx Aabjh YOM - 1995. Fully refurbished in 2021.

Condition: new, functionality: fully functional, machine/vehicle number: 246203 xxxx, Ideal basis for setting up CNC machines and applications The FB2 flatbed unit is ideal for getting started with CNC technology and is ideal for model making and hobby applications. The FB2 is also often used in industry for measuring and dosing technology, as it offers extensive expansion options. The unit also offers access to the isel modular system. Various sizes from travels of 530 x 500 mm to 1030 x 1250 mm and extensions such as base frame and housing are available and can be individually combined. BEST SUITABLE FOR: • modular isel building block system • universal range of applications • easy handling • ideal for laboratory, model making and workshop use • assembly and mounting • printing and engraving • drilling and milling • dosing and screwing • forming and modeling • gluing and casting • soldering and welding • measuring and testing • sawing and cutting and much more Z-passage = 190 mm (Z-passage = 300 and 500 mm on request!) FEATURES: • durable stepper motors in the 200 W range • reliable LES units with steel ball screws are installed as drives • clamping of workpieces using a T-slotted plate • available with and without protective cover • variable gantry apertures, depending on customer application OPTIONS: Fodpfx Ajhqmamjabegh • iSA milling spindles and water-cooled HF milling spindles • Cooling spray device • Cold air cooling, Cool-Min • Automatic tool length measurement • Rotation units • Workpiece clamping systems (hand lever, vacuum clamping tables, etc.) • Suction systems • LED machine room lighting • RAL color selection • CAD/CAM-Software • Diffusers 190 mm, 300 mm or 500 mm • Powerful 4-axis control controller • Underframe • Enclosure with sliding/folding door

Condition: new, FEATURES: • solid and stable machine construction made of ground granite components • small footprint due to compact design high frequency spindle with up to 2 kW power and 50.000 rpm • HSK-E 25 change system • HSC control technology with a block processing time in real time < 1 ms • high path accuracies due to digital length measuring system • high load linear guides • low maintenance linear motors in X, Y, Z • Heidenhain® TNC 640 control • zero point clamping system in the granite table for fast change from 3 to 5 axes OPTIONS: Fsdpfx Aelnk E Soabsgh • 3D measuring probe for detecting workpiece zero points or re-measuring workpieces • laser for non-contact tool control • high frequency spindles up to 100.000 rpm 4th/5th axis as rotary/swivel axis • Minimum quantity cooling lubrication system • Various controls from Heidenhain® • Manual control unit Professional CAD/CAM solutions The PREMIUM 5030 is a 3 to 5-axis HSC milling machine, that is specially designed for the requirements of highprecision processing of fine mechanical small parts, microprocessing and milling graphite/copper electrodes. In order to meet with this demand for accuracy, all essential points are integrated in the machine concept for reliable production. The solid machine base, consisting of a natural hard rock granite portal with decoupled Y-axis, guarantees high stiffness and long-term stability. The individual granite elements are produced with an accuracy per DIN 876 / quality 00. The pioneering linear motor technology and the incremental measurement process guarantee maximum positioning accuracy with highly dynamic feed rates. Fastest control technologies (high-speed cutting) guarantee harmonic rail movements with maximum precision and simple user guidance.

Condition: new, Portal machine - the space miracle! CNC portal milling machine for large traverse paths with small space requirements! ADVANTAGES: -optimized space utilization, completely free table clamping area -best possible chip protection due to overhead axes -particularly suitable for high and bulky components -PILZ safety technology -Windows 10 APPLICATIONS: -chipping -measuring and testing -dosing applications FOR MACHINING: -Aluminum / light metals -Milled plastics -Ceramics -Non-ferrous metals (brass, bronze, etc...) -Plastics -Wood Maximum functionality with minimum space requirements is the motto of the OverHead Gantry M. The basic machine can be optimally configured for many sectors and work areas using a variety of variable equipment features and additional options. The possible applications of the OverHead Gantry M include measuring, testing and metering applications in addition to machining. The power of the milling motor of up to 2.2 kW and 20,000 rpm and a traverse speed up to 250 mm/sec make it suitable for processing wood and plastic as well as light and non-ferrous metals. The free processing area and its excellent price/performance ratio off er decisive benefits compared to similar products. The OverHead® Gantry M is available in five different sizes for different process areas from M20 to M50. Do you require the control cabinet on the right-hand side or would you prefer the control panel to be on the left? No problem – we will be happy to accommodate your requirements. And of course we will take care of maintenance and support for your OverHead® Gantry M. Our service technicians can be reached by telephone and can attend to you quickly on-site as needed. In addition, we also off er our in-house isy-CAM 2.8 software and can advise you on your specific application. Fgjdpjhqhlvsfx Aaboh BENEFITS: -Optimal use of space -Free machining area -Fixed table, mobil portal -Variable clearance of 340- 590 mm -Also suitable for a large chip volumes SET UP: Portal: mobil, Table: Fixed

Condition: new, machine/vehicle number: 280270 0001, ADVANTAGES: compact table machine simple operability 3-axis stepper motor control with path operation Ball screws 2-phase stepper motors CNC control software included ICP series - with stepper motor drive and path control GENERAL CNC machines of the ICP series are further developments of the proven CPM series. The introduction of a sliding door means that the machines can now be operated from a seated position, which results in shorter cycle times for hood opening, among other things. The chassis is completely bolted together instead of welded as in the predecessors. Fjdpfxelkbpzj Aabogh This results in greater precision when setting up the machine, as well as improved serviceability. Furthermore, the resonance and vibration behavior has been optimized, resulting in lower noise levels. X = 400mm Y = 300 mm Z = 140 mm Diffuser = 200 mm -in use for over 40 years!!! -over 20,000 systems sold. HIGHLIGHTS compact table machine simple operability 3-axis stepper motor control with path operation Ball screws 2-phase stepper motors CNC control software included Mosaic Safety Circle POPULAR MATERIAL Foam Plastics ACCESSORIES Length gauge Spindles (iFM1000ER, iFM1000WS) Quick clamping system Spannzangen Suction device