CNC press brake 3200 mm x 125 to

NOVAKRAFT PBS-H 125-3200

Condition: used, L + Z Lathe WEILER Type LZ PRIMUS GS Machine no. No. 2461 Year of construction approx. 1990 Center width 400 mm Turning diameter over bed 250 mm Center height above bed 125 mm Turning diameter over support 140 mm Center height above support 70 mm Spindle bore 24 mm Spindle speed 60 - 3000 rpm 18 steps Feed lengthwise and flat Chuck flange short taper DIN 55022 size 4 Inner tailstock taper MK 2 Drive power 1.1 kW and 1.5 kW pole-changing Mains connection 380 Volt, 50 Hz - 3-axis digital readout FAGOR, type 30i-T-B - Spindle speed via 2 motor speeds and 9 gear stages Fedpfxsrtd Uwj Ah Hopb - 3-jaw lathe chuck RÖHM Ø 125 mm with stepped jaws - MULTIFIX quick-change tool holder with 1 interchangeable cassette - Set of collets Ø 1 / 3 / 4 / 5 / 7 / 8 / 10 / 14 / 15 / 16 / 17 / 19 / 20 / mm - 1 centering tip for collet chuck holder - Emergency stop - Hinged chuck guard - Splash guard - Machine light - electrical diagram - Machine mounted on a steel plate (steel plate L x W x H 1200 x 500 x 30 mm, 140 kg) Space requirement L x W x H 1200 x 900 x 1560 mm Weight 520 kg good condition

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh Fpsdpjhzbipjfx Ah Hob - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: excellent (used), Year of construction: 2012, Technical specifications: Working length: 4300 mm Fpedpfxswl U Rhj Ah Hob Distance between columns: 3230 mm Press force: 400 tons CNC control: AMADA AMNC Number of controlled axes: 5 CNC crowning Stroke: 350 mm Throat: 420 mm Installation height: 620 mm Motor power: 38.5 kW Laser monitoring: FIESSLER Table height: 960 mm Dimensions (length x width x height): approx. 5550 x 2950 x 3400 mm Weight: approx. 29.5 tons Condition: Very good condition, approximately 30,000 hours The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear are consistent with its age; used machines are sold without any warranty.

Condition: used, 5tSWF Krantechnik GmbH Fpedpfedc A R Tjx Ah Hsb

Condition: like new (used), functionality: fully functional, Weiler center lathe model Condor B lead and feed spindle lathe with 3-axis digital readout from K&C NEW Geometrically overhauled with acceptance certificate for tolerances of new machines !!! Technical data: >> Machine no. 90-1495 >> Center height 165 mm >> Center width 750 mm >> Spindle speed : from 22 to 2800 rpm >> Spindle clearance 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feed rates from 0.015 to 0.46 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake can be activated >> Length 1.83 m, height 1.29 m, depth 0.88 m Accessories and equipment: >> 3-axis digital readout from K&C New , 12 months manufacturer's warranty with operating instructions Functions : Switching mm/inch , Coordinate selection ABS/INC , Halving of the display value , Reference mark , Tool programming 200 pcs. , Cone calculation , Radius / diameter , Quick zeros , Switching the counting direction , >> Collet chuck device, collets NEW from 3 to 26 mm 1 mm increasing >> Three-jaw chuck 160 mm with 2 sets of jaws NEW >> Mulifix new size A with 2 steel holders new >> Bed stop Fpodpfx Ahovambcs Hob >> elec. Chuck guard NEW >> Machine lamp LED New >> Rear panel >> Operating instructions >> Coolant device >> Machine feet To the machine : We are offering a Weiler Condor B lead and feed spindle lathe in a geometrically overhauled condition, absolutely as good as new. The guides are newly ground and scraped. With acceptance according to test protocol. A very nice machine with electronic spindle protection. The accessories collets, chuck, Multifix are new. Spindles, spindle nuts, bearings, belts, wipers have been renewed. Take the opportunity to inspect this machine on site under power and see the condition for yourself.

Condition: excellent (used), functionality: fully functional, Year of construction: 1999, Hydraulic press brake PPBL 135/30 Year of construction 1990 Technical specifications Force 1350kN Working length 3050mm Distance between uprights 2250mm Stroke 110mm Distance table – ram 310mm Gap 200mm Width table 180mm Approach speed 100mm/s Working speed 8mm/s Fsdpfxsw Hca Hj Ah Hspb Return speed 65mm/s weight 6500 kg motor 7.5kW Voltage 3 x 380V Oil-tank 120L Options inlcuded; • Back gauge with 2 fingers • Range of back gauge 600mm • 2 front supports of 300mm • Table with center slot Tooling included with machine; • R10.180.78. 6x508mm • Multi-V M90 1x3050mm

Condition: excellent (used), Year of construction: 1996, stroke length: 160 mm, pressing force: 120 t, Hydraulic press brake Fab. DURMA Typ. HAP 30120 Year 1996 Technical details Make: DURMA Type: HAP 30120 Fpjdpsu Iarbsfx Ah Heb Year of construction: 1996 Capacity: 120 tons Effective length: 3050 mm Stroke: 160 mm Engine power: 11 kW Dimensions: L 4,150 x W 1,950 x H 2,600 mm Weight: 7.5 tons Equipment - Controlled backgauge - Immersion depth adjustable via control - Controlled axes: X, Y - 2 support arms - Technical documentation - Tools: o Multi-V die V12, V20 (slightly damaged), V13, V16, V45, V15, V10, V65 Length 3,050 mm o Slightly cranked upper tool, H 150 mm, L 2,970 mm, segmented All information without guarantee. A demonstration is possible at any time in our showroom.

Condition: used, Year of construction: 2008, Equipment: CE marking, lower tooling, safety light barrier, upper tooling, AMADA HFE2204 Pressbrake Pressforce: 220t Fpedpfx Ahow I Dmcs Hob Bending length: 4m Backuage: 4-axis backgauge system Clamping system: Amada

Condition: new, Year of construction: 2025, The ZX7045 B1 DRO milling/drilling machine is an advanced tool created for precision metalworking. It is ideal for drilling, reaming, expanding holes up to 45/40 mm in cast iron, as well as threading screws up to M12 mm. With the ability to mill up to 80 mm wide, notch up to 22 mm, this machine offers versatile applications. The ZX7045 B1 DRO version is distinguished by its auto-feed of the spindle, which increases work efficiency. In addition, it is equipped with a digital readout, which increases the precision of operations, and a cooling system, taking care to maintain the optimum temperature during machining. This tool is ready to use right away, available from stock. Ideal for professionals who demand high quality and performance in metalworking. Product features HEAVY, STABLE CAST IRON AUTOMATIC SPINDLE FEED HEIGHT OF THE MILLING MACHINE IS ADJUSTABLE ON THE SLIDE AND NOT ON THE COLUMN ADDITIONAL LIQUID COOLING SOLID CROSS TABLE WITH PRECISION GROUND SURFACE DOVETAIL GUIDES, QUIET OPERATION THANKS TO GROUND GEARS LEFT AND RIGHT ROTATION HEAD ROTATABLE +/- 900 ADJUSTABLE HEAD HEIGHT Fjdpfx Aoud H H Ueh Hopb DIGITAL READOUT Base available as an optional extra TECHNICAL DATA Drilling capacity in steel 32 mm Drilling capacity in cast iron 45 mm FACE MACHINE DIAMOND 80 mm HANDS CAPACITY 28 mm SPEED RPM 50, 95, 100, 180, 190, 355, 360, 655, 710, 1260, 1310, 2520 rpm. (6/12) MANDREL HANDLE MT 4 Spindle feed 125 mm (AUTOMATIC FEEDING) DIMENSIONS OF THE WORKING TABLE 820 mm x 240 mm DIMENSIONS OF BASE 580 x 600 mm MAX. Spindle distance from the table 445 mm Spindle distance from column surface 260 mm AXIS MOVEMENT X/Y/Z 515/175/430 mm PINOLLE SPEED 0.12; 0.18; 0.25 mm/rev. 90° CLOCKWISE/LEFT HAND ROTATION MOTOR POWER 1,8 kW 2,5 hp POWER SUPPLY 400 V weight 350 kg Available accessories drill chuck shank MK4/B18 digital readout handy tools drill chuck 3-16 mm/B18 reduction sleeve MK4/MK3 reduction sleeve MK3/MK2 English language user manual

Condition: good (used), Year of construction: 2008, control type: CNC control, actuation type: hydraulic, pressing force: 300 t, CNC crowning Hydraulic tool clamping EFL Easy Form laser measuring & correction system Set tooling Laser guide protection Controlled axis Y1/Y2/X/R/V-Axis Max. bending length: 4000mm Distance between supports: 3150mm Max. pressing force: 320T Distance table mount: 570mm Max. stroke: 300mm Table width: 200mm Support throat: 400mm Descent speed: 120mm/min Working speed: 14mm/min Return speed: 130mm/min X-axis range: 1000mm Control: CADMAN Power: 42kW Length: 5800mm Width: 2300mm Height: 3800mm Weight: 23000kg Fedpowrza Asfx Ah Hspb