PANKOKE & KOCHSIEK BFA 05 Drilling

PANKOKE & KOCHSIEK BFA 03 PANKOKE & KOCHSIEK BFA 05 Drilling

Year of construction: 1987, condition: excellent (used), 1 piece chemical standard centrifugal pump with very few operating hours. Ihsdpeh S Nz Sefx Abcsw Pump is suitable for acid condensate and aggressive acids. Also suitable for salt water! Manufacturer: Sulzer Model: ZA 200-4500 Material: Duplex 9.4460 / Noridur 1.4593 Delivery volume: 250m³/h Head: 27 meters at 980 rpm Shaft power: 42 kW Motor power: 75 kW NPSH: 1.6 Speed: 980 rpm Year of construction: 1987 Pump speed of 1480 rpm is also possible! Delivery rate approx. at 1480 rpm (information without guarantee) Delivery rate: 430m³/h Delivery head: 62 meters Shaft power: 88 kW Shut-off valves and piping in stainless steel are also available The material 1.4593 Noridur is very well suited for - Chemical and process engineering industry - Sulphuric and phosphoric acid - Salt extraction and processing - Petrochemical industry Bmg9kmu7ug - Coking plants - Textile and pulp industry - Food and sugar industry - Mining/coal mining and extraction - Flue gas desulphurization plants - Acidic, chloride-containing washing suspensions - Acidic process water - Waste water treatment/sewage treatment plants - Offshore and marine technology

Condition: good (used), Year of construction: 2015, functionality: fully functional, machine/vehicle number: 265864, turning diameter: 350 mm, spindle speed (max.): 5,000 rpm, spindle speed (min.): 35 rpm, travel distance X-axis: 195 mm, travel distance Z-axis: 560 mm, spindle motor power: 15 W, feed rate X-axis: 30 m/min, feed rate Z-axis: 33 m/min, torque: 233 Nm, distance table center to spindle nose: 687 mm, Equipment: documentation/manual, Mazatrol Smart Control. Ihsdpfxsvfm H Ao Abcjw Spindle speed 5000 rpm. X/Z travel 195mm/560mm. Fitted with 215mm diameter. 3 jaw-powered chuck 12-station turret. Tailstock. Tool setter. Part catcher.

Condition: new, table length 2200 mm table width 1500 mm stroke height 1850 mm weight max. in kg 2000 kg Ijdpfx Ajupxwkjbcehw 260 mm total power requirement 1,5 kW stroke speed - idle stroke upwards 40 sek. stroke speed - idle stroke downwards 30 sek. connected load frequency 400 V weight of the machine ca. 0,45 t dimensions of the machine ca. 2,2 x 1,5 x 0,26 m The hydraulic lifting tables are electrically driven and operated. Have a contact strip for safe lowering operation. Wide applicability for workshops, assembly departments, loading pits, etc.

Condition: excellent (used), Year of construction: 2008, Machining center Manufacturer: Weeke Type: BHX 500 Year of manufacture: 2008 machining dimension X: 2.500 mm Ihedpfxsh E Sghe Abcjw machining dimension Y: 1.300 mm Machining dimension Z: 4 - 80 mm Number of milling units. 2 Number of drilling units: 2 Drilling spindles vertical: 72 drilling spindles horizontal X: 16 drilling spindles horizontal Y: 4 grooving saw: 90° tiltable speed X-axis: 130 m/min speed Y-axis: 80 m/min speed Z1-axis: 50 m/min speed Z2 axis: 27 m/min Speed: 18.000 rpm Disassembled - directly available

Year of construction: 1991, condition: like new (used), overall weight: 1,420 kg, rotational speed (max.): 1,485 rpm, 3 stainless steel volute casing pumps in process design 2 x CPK-CM 250-315 built in 1991 1 x CPKN-C1 250-315 year of construction 2011 !!! Price per piece !!! Pumps were operated on a test bench and all have very few operating hours! See pictures !!! Flow rate: 1001 m³/h (278 liters / second) Delivery head / delivery pressure: 18 m / 1.8 bar Pump speed: 1485 1/min NPSH: 5.00 m Shaft seal: single mechanical seal with sealing water Manufacturer: Burgmann Impeller type: closed centrifugal impeller Impeller diameter: 324mm Ijdpfxeqabiao Abcshw Bearing type: roller bearing Lubrication type: Oil Lubricant monitoring Oil level controller Materials: 1.4408 (AISI 316) Pump housing: 1.4408 (AISI 316) Wear plate: 1.4408 (AISI 316) Pressure cover: 1.4408 (AISI 316) Shaft: Heat-treated steel C45+N Impeller: 1.4408 (AISI 316) Bearing bracket lantern: Gray cast iron JL1040 Shaft sleeve: CrNiMo steel Nominal diameter of suction nozzle: DN 300 Discharge connection Nominal diameter: DN 250 Nominal pressure suction side: PN 16 Nominal pressure pressure side: PN 16 Coupling manufacturer: Flender Coupling type: Eupex NH without intermediate sleeve Base plate: Painted gray cast iron Motor manufacturer: VEM K21R 280S4-Z Efficiency class: IE 0 Motor speed: 1480 1/min Frequency: 50 Hz Rated voltage: 400 / 690 V Rated motor power: P2: 75 kW Thermal class: F Motor protection class: IP55 Cosphi: 0.86 Dimensions: Length: 2120 mm Width: 950 mm Height: 1090 mm Weight: 1420 kg

Year of construction: 1998, condition: excellent (used), Kap Saw Reinchardt NC 700 automatic Ihodpfed H Hmhsx Abcjw Manufacturer Reinchardt Model / machine type NC 700 Year of production 1998 Machine category Kapła Kapowa Location Gorzów Wlkp. Conditions of delivery OWN RECEIPT Cost of delivery Customer cover Start type to be agreed Description Comments CUTTING SAW FOR CUSTOMIZED DIMENSIONS, ACCURACY UP TO 1MM, NEW CONTROLLER, SAW BLADDER BY HYDRAULIC AGREEMENT

Condition: used, SPE Renergi Low Temperature Dryer. Ihsdpfx Aswp Rqfobcjw The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: new, functionality: fully functional, Year of construction: 2026, control type: CNC control, degree of automation: automatic, actuation type: electric, laser type: fiber laser, laser source manufacturer: MAX Photonics, laser hours: 10 h, laser power: 3,000 W, laser wavelength: 1,070 nm, sheet thickness steel (max.): 22 mm, sheet thickness stainless steel (max.): 12 mm, sheet thickness aluminum (max.): 12 mm, sheet thickness brass (max.): 5 mm, warranty duration: 12 months, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, safety light barrier, For sale is a high-precision laser cutting machine with 3,000-watt laser power: Type: LG-1313/3kW HaiCut Premium Line - Fully equipped - Innovative 3-gas switching (pressure and gas type can be controlled via software) Cut with N2, O2, mixed gas (compressed air) - Automatic front door - Machine bed lined with fireclay - Machine bed and axes measured and calibrated using Renishaw interferometer Our goal is to offer the best, most reliable, and competitively priced laser machines currently available on the market. Our machines are ideal for workshops and repair businesses. A perfectly developed cutting parameter library is included as well as top-tier on-site service. Please also note our attractive leasing/financing options. Brand new machine, delivery time approx. 6-8 weeks We would be happy to demonstrate the machine to you at our facility. Travel range: approx. 1300 x 1300 mm Ihedoi Igauopfx Abcjw Table area: approx. 2500 x 1300 mm (plenty of space for medium-format sheets) Pull-out cutting table For high-precision metal cutting Fully installed and calibrated Cutting software in German Incl. nesting module Very easy to operate Just switch on and start cutting Laser source by Max Photonics (G5/German version) with 3,000 watts power Comprehensive electronic and mechanical collision protection measures for the cutting head Large laser safety window in the front door Automatic front door Safety light curtain for maximum operator protection Cutting capacity: - Stainless steel up to 12 mm - Mild steel up to 22 mm - Aluminum up to 12 mm - Brass up to 5 mm Heavy-duty industrial quality Complete system / ready for immediate use LED work area lighting 200 mm duct connection for fume extraction Incl. exhaust fan Leasing or hire purchase available via our financing partner. Need different power or table size? No problem, we have multiple machines in stock or available at short notice. Sale to commercial customers only. Delivery/advice/sales exclusively in Germany, Austria, or Switzerland. Machine dimensions approx.: Width: 3.5 m, Height: 2.1 m, Depth: 3.5 m Weight: approx. 2.5 tons

Condition: new, Year of construction: 2022, Dowel hole drilling device: no Drilling depth: 150 mm oblong hole length: 180 mm Height adjustment travel: 145 mm Iedpogq Un Aefx Abcehw Motor power: 1,5kW Speed: 3000 rpm Suction connection: 100 mm Machine length: 1280 mm Machine width: 960 mm Weight: 240 kg

Year of construction: 1995, condition: excellent (used), 3 units centrifugal pumps Sulzer MB 40-160/5 Flow rate: 32 m³/h Head: 147 m Max. temperature: 130°C Ihedped Sybpefx Abcow Seal: Mechanical seal with barrier water Drive power: Siemens 22 kW Speed: 2950 rpm ! Price per unit !