Hydraulic press 14 stations

POLYGRAPH K 14

Condition: new, Year of construction: 2025, pressing force: 100 t, stroke length: 400 mm, - Cylinder stroke 400 mm Ijdpfx Abjgp Dc Rsceap - Working width 1010 mm - Cylinder is movable - Can be operated electrically or manually - Pressure indicator - Emergency stop - 400V

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Iodpfsg U Utvox Abcjap Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Reel stand in strong box construction as welded design. construction. Additional equipment: Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable.

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz Iasdpfehlnzkox Abcop - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: as good as new (ex-display), Year of construction: 2008, machine/vehicle number: LSP 100T, Productions-Hydraulic press with H-column 100t with guidance Manufacturer: Stenhoj Denmark Year of construction: 2008 Pressure force max. 1,000 kN / 318bar Press cylinder, stroke length: 400mm Iaedpfx Asg Rn Efsbcep Press table with T-slot 1,500x900mm above 1,500x1,050mm below Stand passage 1,700mm Condition as good as new, the machine was only used for test runs and has been in stock since then. All statements without guarantee. Without transport costs.

Year of construction: 2009, condition: used, material width 320 mm material thickness 8 mm Iaedpfx Abep U Uwiecop no. of straightening rolls 9 material cross-cut 2000 mm² weight of the machine ca. 4,2 t dimensions of the machine ca. 2000x2000x2400 mm

Condition: new, Year of construction: 2025, Band width: max. 38 mm Feed length: max. 50 mm Band thickness: 0.05...1.02 mm Stroke rate: max. 260 rpm at full feed length Feed force: 90 N Iajdpfxj Ea U He Abcjp Optionally with mechanical control valve or optionally with electric valve (24V or 230V) Many other band widths and feed lengths available.

Condition: refurbished (used), Year of construction: 2020, pressing force: 500 t, pressure:500 t passage width:1100 mm stroke:600 mm weight of the machine ca.:ca. 22,8 t Table area:1100 x 800 mm ram surface:1100 x 800 mm Daylight Opening:800 mm Hydraulic:300 bar closing speed:60-200 mm/sec pressing speed:0 - 9,5 mm/sec opening speed:28-200 mm/sec Table height above ground level:900 mm height over floor:5100 mm workpiece weight max.:2000 kg workpiece weight top:1000 kg halls height:min. 6500 mm Ijdeffamvjpfx Abceap Number of pressing cylinders:1 St. number of driving cylinders:2 St. :ca. 270 Lt./min. Oil Tank Capacity:600 l main drive:75 kW Control technology from Siemens:S 7 Safety control:PILZ Multi

Condition: used, Year of construction: 2021, machine/vehicle number: HB 2022-A-073, pressing force: 300 t, Portal straightening press with 300 T capacity a) idle and pressing speed up to 17 mm/sec. b) opening speed up to 55 mm/sec c) table size 2500x1600mm d) open height 700 mm e) total size approx. LBH 4500 x 2300 x 3700 mm f) Oil temperature indicator on the tank g) Lubrication via grease nipple h) table in grid construction,with T grooves according to customer's request, otherwise 22mm i) operation on swivel arm, mounted on the bridge j) pressure adjustment from 50 T to 300 T via MONITOR k) bridge moves by two gear motors, via racks l) Cylinder moves to the left and to the right via toothed racks m) Machine body double painted n) Cylinder induction hardened Type of construction Press design PORTAL PRESS Thermally neutral 80 - 120 °C Number of operating sides 3 side Forces Pressing force max. 3,000 kN Free ripping force max. 500 kN Pressure build-up time Closed die Steel to steel Max. 3 sec. Dimensions Max. Opening width 700 mm Stroke and min. opening 700 mm/ 0 mm Table height above floor approx. 9ß0 mm Height above floor (headroom) approx. 3700 mm Hall height min. 5.000 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.8 mm/m Weight Total weight of press without operating materials and table plate approx. 22 T Speeds Fast closing with 17 mm sec. Pressing speed 8 mm sec. Opening 55 mm sec. Sound pressure Sound pressure level, measured at 1.5m height at the control panel after max. 78 db(A) DIN 45635-T16-KL3 Hydraulics Number of pressing cylinders 1 pc. Operating pressure max. 350 bar Pressing pressure build-up time 02. mz sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump Iaodpfx Aoh Agnusbcop BOSCHREXROTH approx. 93 L/min Oil volume approx. HLPD 46 MW 900 liters Ambient temperature max. 45 °C Oil temperature max. 55 °C Electrical system Main supply 400 V AC Control voltage 24 V DC Frequency 50 Hz Hydraulic connection Main motor IE3 22 kW Total connection Approx. 30 kW

Condition: used, material width:304,8 mm material thickness:0,12 - 2,2 mm feed length:304,8 mm clamping force of fastening pincer:850 N clamping force of moving pincer:4410 N Isdpfocxxrxox Abceap feeding force:650 N weight of the machine ca.:0,15 t dimensions of the machine ca.:0,7 x 1,05 x 0,6 m

Condition: used, Year of construction: 1984, material width:350 mm coil weight:1 t material thickness:0,5 - 6 mm coil internal diameter:380 - 540 mm coil external diameter:1500 mm no. of straightening rolls:9 straightening roll diameter:30 mm number of draw-in rolls:2 weight of straightening machine:2 t dimensions straightener (WxDxH):2,0 x 2,0 x 1,9 mm Iaedpot Hmk Tofx Abcep weight of decoiler:1,3 t dimensions decoiler (WxDxH):1,7 x 1,5 x 1,6 m