MACHINING CENTER

POUWELS DEF 1000

Condition: new, Cam-driven spring forming machineCam-driven spring forming machine Hodjmb Uurjpfx Abtot

Condition: excellent (used), Year of construction: 2001, turning diameter over cross slide: 1,600 mm, turning length: 6,000 mm, turning diameter: 1,300 mm, spindle motor power: 1,00,000 W, total height: 2,875 mm, total length: 9,550 mm, total width: 2,950 mm, workpiece weight (max.): 40,000 kg, Swing over bed Ø 1600 mm Swing over cross slide Ø 1300 mm DBC Turning Length 6000 mm Spindle power 100 kW Tailstock spindle Ø 280 Ø Stroke pinole 200 mm Workpiece weight 40000 Power 125 A Speeds / ranges 250 Rpm Dimensions (Estimate) Length 9550 mm Width 2950 mm Height 2875 mm Hodpfx Aoymk E Aobtot Weight 41000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, 72″ x .187″ x 50,000Lb Paxson Loop Slitting Line Make: Paxson Material Width: 12″ – 72″ (Uncoiler 60″) Material Width: .010″ – .187″ Coil Weight: 50,000Lb Coil ID: 20″ – 24″ Coil OD: 72″ Speed: 500 /1000 fpm Direction: Right to Left Material Strength: 40,000 yield / 50,000 psi shear Material: CR, HR, Galvanized Hodpoihf Ufefx Abtst Entry Transfer Cart Entry Coil Car Mandrel Uncoiler Powered Hold-Down Roll Powered Expansion Sliding Base Hydraulic Peeling Table Driven Pinch Rolls

Year of construction: 2006, condition: like new (used), Pneumatic tensioning and leveling device for band saws. Hodpsdy A A Nofx Abtjt

Condition: good (used), Year of construction: 2011, machine/vehicle number: 2212.287, Automatic panelsaw Schelling Typ:FH 6 430 Maskin nr:221.287 År:2011 Panel beam saw Schelling with automatic, rear-feed,lifting table. For sawing board material, chipboard, MDF, Plywood, Board, Laminate etc. Techn info: Software MCS Evolution 2.0, SPS, Soft-SPS-Siemens WinAC Operating system WINDOWS XP PC with keyboard and mouse TFT monitor 17" Cutting length 4300mm, automatic detection of the start of the plate Cutting width 4300mm Machine accuracy of the cut length 3m +-0.1mm Positioning accuracy measured at input +-0.1mm Max diameter saw blade 460mm, spindle 30mm Pre-scoring blade 200mm, spindle 20mm motor operation is set from the control console Max panel thickness 120mm Panel stack aligner Main saw blade motor 27kw Saw blade over table 135mm Safety curtain Air cushion table with 3pcs air ball nozzles, radial ventilator fan Table sizes 2650x850mm 620x850mm 2650x2550mm Pressure beam with automatic adjustment of pressure to cut length and package height Package straightener before and after the pressure beam Max package height 120mm (incl. sum of curvature and board thickness tolerance) Pusher with 12 grippers Max clamp opening (gripper) 133mm Min-max force package straightener 400/2000N Speed saw carriage forward 6-150m/min Speed saw carriage back 150m/min Forward feed speed (pusher) up to 25m/min (according to EC Europa EN1870-13) other countries 80m/min Speed feeding back up to 80m/min Push-off device 3 pcs Lift table length x width 4350x2550mm Hydraulic unit Standard version 1600mm lifting height 1.25/2.5m/min raising speed, 1.25/5m/min lowering speed Maximum load 1200 kg/m2 total 9 tons Roller track driven rollers, frequency controlled for stack on lifting table 4100x2600mm Max stack weight 6500 kg Max stack length 1060mm Slots for forklift 4 pcs, distance in the middle 1200mm, slot width 300mm Hodpfxjtk It Ss Abtet Light curtain for personal protection Roller conveyor driven for package frequency controlled input to lifting table left 5600x2600mm max load 6500kg Roller conveyor driven for packages frequency controlled input to lifting table right 5600x2600mm max load 6500kg Slots for forklift 2 pcs, center distance 900mm, slot width 400mm 2 positioning stops with roller for stack alignment Light curtain (double beam) for personal protection Roller table after saw depth 4300mm, free-running ployamide rollers Angle stop at the rolling table Infeed guide two-lane (beam length 7200mm) 2-sided hardened precision guides rack and pinion drive, two-sided Input carriage (pusher) gear rack servo drive, non-contact measuring system Gripper, (scissor clamps) in pusher 12 pcs Automatic adaptation of the clamping force to the package height (progressive clamping force) can be set to 0 Pusher for panels thickness greater than 6mm,material thinner than 6mm is fed manually Central cleaning system feed trough (pusher) Compressed air 6-8 bar, approx. 1600l/min Power 38 kw, 70 A. 3x400 volts, 50 Hz, operating voltage 24 VDC Dust extraction 4000m/h, air speed 30m/s Diameter connection 80mm (angle connection), 120mm /pressure beam), 150mm (sawdust channel) Total setup area without driven roller conveyors including protective grid approx: 11650x7300mm Driven roller tracks left-right 5500+5500mm Stock no: 2002125BXACEO Subject to incorrect technical data presented

Year of construction: 2007, condition: good (used), MAKE - LVD, Made in USA/BELGIUM MODEL - GLOBAL 20 1225 YEAR - 2007 CONTROL - FANUC 180I - PB CAPACITY - 20 Tons THROAT DEPTH - 1250.0 mm SHEET SIZE MAX. - 2500.0 x 1250.0 mm (1250.0 x 5000.0 mm) MAXIMUM WORK PIECE WEIGHT - 150 Kg MAXIMUM MATERIAL THICKNESS - 6.0 mm MAXIMUM TABLE SPEED - 0 – 4330.0 TURRET - 30 STATIONS, 4 AUTO-INDEXING MAXIMUM PUNCHING DIAMETER - 89.0 mm PUNCHING SPEED - 350 STROKES/MIN NIBBLING SPEED - 900 STROKES/MIN Hedpfx Aoiab Epsbtet PRESS MOTOR POWER RATING - 460V 3 Phase Motor DIMENSIONS - 5560.0 x 5560.0 x 2400.0 mm WEIGHT - 16,000 Kg PLUS BRUSH TABLE VERY LOW HOURS GOOD RANGE OF TOOLING

Condition: used, TECHNICAL DETAILS - Number of axes : 7 - Number of spindles : 2 MAIN SPINDLE - Max. bar diameter : 20 [mm] - Max. machining length : 205 [mm] - Spindle speeds : 10000 [rpm] - Spindle power : 3.7 [kW] - C axis indexing precision : 0.001 [°] COUNTER-SPINDLE - Max. bar diameter : 20 [mm] - Spindle speeds : 8000 [rpm] - Spindle power : 2.2 [kW] - C axis indexing precision : 1 [°] - Number of guide bush holders : 1 GUIDE BUSH HOLDER 1 - Number of positions : 10 - Number of motorized positions : 4 END ATTACHMENT - Number of positions : 7 SECONDARY OPERATION - Number of positions : 4 - Number of motorized positions : 4 - Live tools speed : 8000 [rpm] POWER SUPPLY - Supply voltage : 400 [V] - Total installed power : 7 [kW] WEIGHT & DIMENSIONS - Machine floor space : 2200 x 1200 [mm] - Machine height : 1700 [mm] - Machine weight : 2200 [kg] MACHINE HOURS - Number of hours under power : 107555 [h] - Number of working hours : 91025 [h] - Number of spindle hours : 54783 [h] Hodpfx Aey Dim Iobtot EQUIPMENT - CNC : Fanuc 300is-model A - Rotating guide bush - Parts catcher - Parts conveying strip - Ejection of workpiece - Coolant tank

Condition: good (used), Year of construction: 2005, Used cutting machine Lectra Vector 5000 Fashion V3 - year 2005 - Useful cutting width 180 cm. - translating - new inverter device - in good condition. Hedpfxortncce Abtst

Condition: used, Year of construction: 2012, Feeler NBP 1300A Year of manufacture 2012 X-axis travel 1300 mm Y-axis travel 610 mm Z-axis travel 600 mm Table 1500x600 mm Spindle 12,000 rpm BT40 Hedpfx Aeww Indsbtot Spindle coolant Heidenhain TNC 530 control

Year of construction: 2023, condition: new, ! Machine offer for customers in Lithuania / Latvia / Estonia. The LVD PHOENIX laser is fiber laser cutting machine which combines high dynamics with flexibility for cutting thick material. PHOENIX is available in different sizes: 3m x 1,5 m, 4m x 2 m and 6m x 2m. Power source varies from 4kW to 20 kW. As standard machine is equipped with automatic shuttle tables, cutting head, adaptive collimation unit (until 12kW), capacitive height sensing, automatic nozzle cleaning, automatic sheet referencing, automatic cutting gas selection (oxygen, nitrogen and compressed air), chiller and fume extraction, SIEMENS control unit. The PHONEX laser cutting machines are compatible with huge range of automatization solutions such as loading / unloading and sheet storage (up to 6 meters), nozzles changer. Hedpjiy N Npefx Abtet Shuttle table All PHOENIX lasers come with automatic shuttle tables. The height of the table is 930 mm. The speed of table change depends on laser size: for 3015 – 35 sec., for 4020 -39 sec. and for 6020 – 48 sec. Tables on PHOENIX 4020 and 6020 models are split into 2m x 1m modules for easy replacement. Cutting head Laser source power on PHOENIX laser cutting machines varies from 4 to 20 KW (available: 4kW, 6kW, 10kW, 12kW, 20kW). The cutting head for 4 – 12 kW lasers could be equipped with 150 or 200 mm focusing lens, for powerful 20kW lasers – 250 mm focusing lens are used. Frame The PHOENIX 3015 model has a welded steel mono frame construction. This allows high accelerations without losing the accuracy. Due to the high frame rigidity, no special foundations are requested. The frame of PHOENIX 4020 and 6020 exists out of 4 parts. One rigid left and right frame that are connected with two bolted beams.