Cut-to-length and slitting line

SALICO slitting line 1250x13mm x25t (A3797)

Condition: refurbished (used), SCHLATTER Welded wire mesh production line MG24 Full revamped WORKING RANGE Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Adjustable by cutting device (0-1) Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24 WELDING MESH MACHINE MG 24.1/8C, Basic equipment including: - 1 Machine frame - 1 Upper support for press reception, continuously adjustable by hand crank - 1 Magnet supports with retaining magnets and weft wire monitoring. - 1 Row of pneumatic solenoid valves for press actuation. - 1 Installation for air and water. - 2 Pneumatic rotary drives with oil damping - Static motor torque with 5 bar compressed air: 480 Nm - Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1) - 1 Advance carriage with panel lifting device - 1 Set of tools for machine adjustment WELDING SECTION 8 Type C Transformers Rated power of each transformer: 100 kVA No-load secondary voltage: 7.1 V Hsdpfx Agswu Tu Ds Nsi Rated secondary current: 14 kA 8 Thyristor contactors ES 130 12 Welding presses: 5.0 kN 12 Chain current bridge for spacing of warp wires: 50-100 mm 12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm 10 Chain current bridge for spacing of warp wires: 100-150 mm 8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm 6 Chain current bridge for spacing of warp wires: 150 - 200 mm 6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm 24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm 24 Wire clamping pliers Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24

Condition: new, Year of construction: 2024, A vineyard post roll forming machine is used for vineyards and orchards to produce the stakes and posts. Normally, grape posts are 1.5-2mm thickness. The production line consists of Decoiler, Servo Feeder Straightener, Press, Stamping Tool, Roll Form Machine and Shear. Hjdpfxet Tcz Us Ag Nei

Condition: like new (used), functionality: fully functional, Year of construction: 2014, operating hours: 24 h, I am selling full complete onion peeling processing line with M&P onion peelers, items are listed below: -6x M & P onion peeler machine -all conveyers, elevators for transport peeled, unpeeled and waste product -inspection table -all working platforms -all hoppers for row (unpeeled materials) Excluded air screw compressors but for serious enquire i could help out with additional equipment. Capacity 2700- 4500 kg /h of peeled onion Hsdpfotzmifsx Ag Nji

Condition: excellent (used), Year of construction: 2023, operating hours: 106 h, lifting height: 5,000 mm, fuel type: diesel, mast type: triplex, power: 185 kW (251.53 HP), gearing type: automatic, fork length: 3,000 mm, color: red, Transmission: Hydrodynamic powershift, 3 gears, automatic Year of manufacture: 2023 Unladen weight: 46,760 kg Lifting capacity: 33,000 kg Overall height: 370 cm CE certification: yes Technical condition: very good Visual condition: very good KALMAR DCG 330-12 FORKLIFT TRIPLEX FULL FREE LIFT FORK SHAFT SYSTEM 33,000 KG at 120 CM SHORT WHEELBASE = 475 CM FORKS: LENGTH = 300 CM, WIDTH = 30 CM, THICKNESS = 11 CM FRONT AND REAR VIEW CAMERAS TIRE PRESSURE MONITORING CENTRALIZED LUBRICATION LED LIGHT PACKAGE CHASSIS / BODY: - Towing pin - Steps with slip protection - Rearview mirrors mounted left and right on the front fenders - Heavy-duty and protective fenders CAB: - EGO cab Hedpfx Aev Hn D Eog Noi - Clear and hardened safety glass, thickness 6 mm - Clear windows including sliding windows in the left and right doors - Full doors with locks left and right - Complete control system on right console including light control, rotary dial for display, levers for load handling system (electrically adjustable, 2-way) - Multifunction lever on left side including horn, indicators - Braking system with pedal left and right - Cabin comfort including mirrors, handles, interior lighting, etc. - Wipers and washers for front/rear and roof window - Hydraulic steering with electrically height-adjustable steering wheel, manual fore-aft and lateral adjustment with steering knob - External reverse lights - Tiltable operator’s cabin - Step handle, left - Automatic heating and ventilation (ECH) with fresh air filter - Speed control pedal right - Kalmar standard key system - Cup holder - Coat hook - Color display: fuel level, indication; engine and transmission temperature; engine oil pressure; battery voltage; clock and date; operating hour counter; service interval display; speed; engine RPM; various popup information; AdBlue display STEERING SYSTEM: - Kalmar steering axle, including double-acting steering cylinder DRIVE TRAIN: - Axletech drive axle HYDRAULICS: - Electric servo - Sight glass on hydraulic oil tank - Variable displacement pumps - High-pressure filter - Automatic increase of engine speed when using the load handling function - Standard tilt angle 5F/10B ELECTRICAL SYSTEM: - 24 V electrical system - Rear and brake lights, LED - Working lights on front fenders, LED - 2 mast working lights - Turn signals including hazard lights, LED - Main power switch WHEELS: - Michelin 16.00x25

Condition: used, Rotary vane vacuum pump Oil circulation lubricated Manufacturer: Busch Type: RC 1000 B Status: Refurbished Hjdpfecu Tirjx Ag Nsi Warranty: 12 months Suction capacity: ca.1000m³/h Ultimate pressure: approx. 20 mbar Operating medium: Mineral oil (Inclusive) Delivery time: 2 Wo.

Condition: good (used), Year of construction: 2008, control type: CNC control, actuation type: hydraulic, pressing force: 300 t, CNC crowning Hydraulic tool clamping EFL Easy Form laser measuring & correction system Set tooling Laser guide protection Controlled axis Y1/Y2/X/R/V-Axis Max. bending length: 4000mm Distance between supports: 3150mm Max. pressing force: 320T Distance table mount: 570mm Max. stroke: 300mm Hjdpfxowrza Aj Ag Nei Table width: 200mm Support throat: 400mm Descent speed: 120mm/min Working speed: 14mm/min Return speed: 130mm/min X-axis range: 1000mm Control: CADMAN Power: 42kW Length: 5800mm Width: 2300mm Height: 3800mm Weight: 23000kg

Condition: good (used), Year of construction: 2000, SANJO PO3-350 / Offset Labelpreess We present this SANJO PO3 Offset Labelpress max format 254mm x 330mm / year of manufacture 2000 Machine details:  Year of construction: 2000  Printing process: 6 x Offfset (Toray)  FLEXO VARNISH UNIT  unwind unit  CORONA DISCHARGE UNIT  2 x HOTSTAMPING UNIT  1 x AIR COOLING DEVICE  UV AIR COOLED UV UNITS  FLATBED DIE CUTTING STATION Hedpeu I Nu Sefx Ag Nei  SANJO REWINDER with SPOR VARNISHER  MULTIPASS UNIT  High Speed modification has been included Technical- and optical condition: Technical: 9/10 (checked and in excellent running condition) Optical: 9/10 (cleaned and can go to end-user directly)

Year of construction: 2020, condition: excellent (used), 2 cats EK DMR Hjdpfx Agstu Nmds Noi

Year of construction: 1999, condition: excellent (used), ULMA ALASKA ID.NO. 2723 Ulma Alaska flowpack with associated gas mixer model year 1999. Max width film 720 mm, Product size 100-250 x 100 x 440 H 15 - 125 mm. Capacity up to 40 packages / min. Hedpfxsr H D Rye Ag Nsi Dimensions 600 x 120 cm Height 170 cm.

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. Hedjhzbipspfx Ag Nsi - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.