Thread milling and hobbing machine

WMW HECKERT ZFWVG 250x800

Condition: good (used), Year of construction: 1999, CONFIGURATION, ARCHITECTURE: PARALLEL LATHE GUIDANCE: PRISMATIC, 3 WAYS THE CARRIAGE CAN MOVE WITHOUT INTERFERING WITH THE TAILSTOCK AND STEADY RESTS, ESPECIALLY SUITABLE FOR SHAFTS DISTANCE BETWEEN CHUCK AND TAILSTOCK: 6000 mm Ijdpfsyhrnuox Ab Isbb CHUCK DIAMETER: 1000 mm SWING OVER BED: 1020 mm TURNABLE DIAMETER: 700 mm BED WIDTH: 900 mm LOAD CAPACITY BETWEEN CHUCK AND TAILSTOCK: 12,000 kg 4-POSITION AUTOMATIC TOOL TURRET: YES MOTORIZED TAILSTOCK: YES SPINDLE SPEED: 1–720 rpm CONTROL (BRAND/MODEL): SIEMENS 840 D POWER LINE AIR CONDITIONING IN ELECTRICAL CABINET: YES CHIP CONVEYOR: YES, DRAG-TYPE, NEW IN 2021 EXTRAS OPEN STEADY REST: 2 UNITS CLOSED STEADY REST: 1 UNIT INSTALLED MACHINE DIMENSIONS (L x W x H): 14 x 3 x 2.5

Condition: good (used), Year of construction: 2000, gear diameter: 449 mm, Equipped with: Fanuc 150MB CNC Control Dry Cutting Cutter Shroud Chip Evacuation System Auto Doors Hydraulic System Lubrication System Work light Stack Light Specifications: Largest Speed Ratio: 10:01 Work Area (Continuous): Largest Depth of Teeth: 15.24 mm Largest Width of Tooth Face: 50.8 mm Work Area Axis: Horizontal Movement X Axis: -114 - 178 mm Vertical Movement Y Axis: -178 - 190 mm Movement of the Carriage Baseplate Z-Axis: -10.16 - 500 mm Workpiece Headstock Swiveling Range B-Axis: -3 - 90 Degree Maximum Distance Machine Center to Spindle Side: 165 mm Number of Teeth: 5-200 Inclusive Max. Gear Pitch Dia. of Typical 35 Deg. Spiral Angle Gear Using Max. Cutter Dia. 12" Cutter at the Following Ratios: Face Milling 1 x 1 - 13.5" - 342.9mm 2 x 1 - 16.0" - 406.4mm 5 x 1 - 17.7" - 450.0mm Face Hobbing (210mm Dia. Cutter) 1 x 1 - 10.560" - 268.22mm 2 x 1 - 10.286" - 275.00mm 5 x 1 - 11.810" - 300.00mm Milling Head Diameter: Helixact: 100,125,169,200,250,320mm Continuous Gumption Procedure, Teichloroethylene: 102 - 210 mm Workpiece Spindle: Drilling of Large Diameters: 5 3/64" Cone Upward Gradient on 304.8 mm (1 Foot): 21/32" Deep One of the Cone: 5.29" Diameter of the Whole Spindle Perforating: 3.35" Ibedpfxsruakgj Ab Isb Speeds: B-Axle Workpiece Headstock Drag Axis: 30 Degrees A-Axle Workpiece Spindle Number of Revolutions: 0 83 min-1 X-Axis Horizontal: 80 mm/sec Y-Axis Vertically: 80 mm/sec Z-Axis Carriage Baseplate: 80 mm/sec Space Requirement L x W x H (Approximate): 4.75 x 3.40 x 2.54m / 188" x 134" x 100" Machine Weight (Approximate): 10980 kg / 24,156#

Condition: used, Year of construction: 1984, functionality: fully functional, travel distance X-axis: 1,800 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 2,000 mm, table load: 5,000 kg, spindle diameter: 110 mm, total height: 3,800 mm, total length: 5,000 mm, total width: 3,000 mm, table length: 1,520 mm, table width: 1,225 mm, feed length X-axis: 1,800 mm, feed length Y-axis: 1,500 mm, feed length Z-axis: 2,000 mm, Tool holder SK50, Heidenhain control, machine is ready for collection and immediately operational. Ijdpsxga Tnjfx Ab Isbb

Condition: good (used), Year of construction: 2009, max. wheel diameter 1200 mm gear width 260 mm max. module 16 min. module 0,5 stroke 270 mm distance between table/spindle 920 mm taper of shaper cutter SK control Bosch MTX table diameter 900 mm min. workpiece diameter-at internal hobbing 1200 mm strokes - infinitely variable 50-1000 Hub/min spindle diameter 125 mm Ibedpfjwzmpzex Ab Isb table hole 320 mm Distance of shafts Min/Max 0-820 power capacity Stosskopf 30 KW total power requirement 72 KVA weight of the machine ca. 24 t dimensions of the machine ca. 6,5x2,9x4 m Liebherr LH 90 control, 9 axis CNC, top condition.

Condition: used, Year of construction: 2007, x-travel 900 mm y-travel 300 mm z-travel 1000 mm control Siemens Sinumerik 840D max. workpiece diameter 1600 mm max. module 20 mm tip circle diameter 350 mm Milling arbour diameter 375 mm Total closing value 80 kVa weight of the machine ca. 33,5 t dimensions of the machine ca. 10,530 x 6,375 x 4,680 m Feed rate: - X-axis 1 to 3000 mm/min - Y-axis 1 to 3000 mm/min - Z-axis 1 to 4000 mm/min Spindle speeds in rpm: - Tool 26 to 265 - Workpiece table 0 to 8 Equipment/accessories: - M 2 motor milling head - Milling mandrels - Oil cooler Ijdpfxew Rrb Hj Ab Iobb - Technical documentation

Condition: used, Year of construction: 1990, turning diameter 2400 mm Ibsdpfx Aoygx D Hob Iob faceplate diameter 2200 mm turning height 2100 mm control SIEMENS Sinumerik 850T workpiece weight 17 t Tol measurements 32 Werkzeuge Crossbeam travel: 700mm Crossbeam support Travel from centre of rotation to the right: 700mm Crossbeam support Travel from centre of rotation to the left: 700mm Machine table drive Main drive power: 80kW Number of gearboxes: 2 Step change: 3.84 Speed range of the 1st gear stage: 2-32-139 rpm Speed range of the 2nd gear stage: 9-125-500 rpm Max. Machine table load: 6 tonnes Feed drive Cross beam support Horizontal feed speed: 0.1 - 8 m/min Cross beam support Vertical feed speed: 0.1 - 8 m/min Cross beam support Rapid traverse speed horizontal/vertical: 8 m/min Cross beam adjustment speed: 425 mm/min Tool system Tool system: 180.1 Cutting force on the turning tool: 30 kN

Condition: good (used), Year of construction: 2000, functionality: fully functional, machine/vehicle number: 018.0179.90.035, (Please tell us your offer price) Sale only within Europe, incl. Turkey Price without packaging; delivery condition: FCA (machine location) ===== Technical data see handout. All warranty rights are excluded. For the correctness of the technical data and year of construction, for the completeness of accessories and tool equipment, and for compliance with all safety and environmental protection requirements specified in the accident prevention regulations. No sale to private individuals. Ibsdpfeyh R Uwex Ab Iob Sales only within Europe, incl. Turkey Price without packaging; Delivery condition: FCA (machine location) ===== Technical data please see handout in attachment. German text leading language. Without any guaranty and warranty, including completeness of tools & accessories as well as environmental and safety regulations. No private sales.

Condition: excellent (used), I am selling this machine, connected, can be tested. Max. workpiece diameter ..... 1600 mm Iodpfx Abov Nqpps Iebb Module ..... 16 - Power of the main electric motor ..... 12 kW Dimensions l x w x h ..... 4300 x 2000 x 3170 mm Machine weight ..... 18500 kg Can send a video of the machine, via whatsapp.

Year of construction: 1995, condition: used, machine/vehicle number: 18891, Force: 10 to. Stroke: 1000mm 3 Broaching-stations With chip-conveyor + platform and safety door Ijdpjbrcmkefx Ab Iebb

Condition: used, Year of construction: 1998, Technical details: max. module: 7 weight of the machine ca.: 5 t worm grinding diameter: 280-350 mm Iodpfx Abezgw I Ne Iebb width of grinding worm: 84-104 mm min. number of teeth: 6 max. number of teeth: 600 max. top circle diameter: 360 mm max. workpiece weight: 60 kg with Turbo Separator, loading unit, latest-generation balancing and dressing unit and various accessories *