Bending press multiprogram

Zopf T 300 Multisteuerung

Condition: new, Year of construction: 2025, overall weight: 1,000 kg, Horizontal bending machine T 300 Multi new version - ZOPF - with semi-automatic control - (99 bending programs each 16 steps) - hydraulic pressure 30 to. Crodpfx Aswqftdoa Nsb - length of stroke 250 mm - bending speed adjustable - max. working speed 10 mm/sec. - return speed 20 mm/sec. - hydraulic pressure adjustable - maximum bending high 250 mm - motorcapacity 3,0 KW - 400 V 50 hz 3 ph. - working height 900 mm - closed table - replaceable wear plate - weight 950 kg - colour RAL5012 / RAL7015 - bending capacity: flat material max. 200x20 mm round tube 3/8" - 2"

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Credpfokvnumex Aa Nsb Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length 3000 mm Width 2200 mm Height 2500 mm Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 2007, machine/vehicle number: 001669, Lg 33121 Single side decoiler ARKU AH 3000/ST-M year of manufacture 1995 belt width max. 600 mm load capacity max. 3.000 kg coil outer diameter max. 1.800 mm Spreading hydraulic Pressing arm hydraulic Decoiler with auxiliary drive and brake coiler chair fixed + reel traversing device with: Lg 33221 High performance belt leveler LORENZ BRM 50/620.9 year of manufacture 2007 Machine no. 001669 passage width max. 620 mm number of straightening rolls 9 Straightening roll diameter 50 mm Material density 0.7 to 6.0 mm Straightening rolls supported several times against deflection All rolls driven by transfer gearboxes and cardan shafts. cardan shafts. Credehigmbepfx Aa Nsb Used, in as-is condition from stock, available immediately. On request with overhaul. Delivery time by agreement. Further data shortly or on request.

Condition: used, Year of construction: 2007, working width 1380 mm workpiece height 70 mm total power requirement 45 kW Cedpfx Aast Hw Iio Njrb weight of the machine ca. 5.500 kg

Condition: good (used), turning diameter over bed 280 mm turning diameter over slide rest 170 mm turning length 600 mm weight of the machine ca. 400 kg spindle passage 26 mm speeds 55-2000 U/min total power requirement 1,4 kW dimensions of the machine ca. 1,5 x 0,8x 1,3 m Including EMCO SOD grinding support Including EMCO 4-jaw chuck Including machine feet Including change gears Csdpfoyz Dg Rsx Aa Nerb

Condition: good (used), Brand Ercolina Model CE40H3 Year of manufacture 2006 Hydraulic drive Roller diameter Ø 165 mm Shaft Ø 40 mm Tube capacity (thin-walled) Ø 70x1.5 mm min. Ø 700 mm Crodjw Hx Tvepfx Aa Nsb Tube capacity (thick-walled) Ø 2" x 3.2 mm min. Ø 450 mm Angle section capacity 50x50x6 mm min. Ø 400 mm Flat bar capacity 50x10 mm min. Ø 250 mm Flat bar capacity (hard edge) 100x15 mm min. Ø 250 mm Box section capacity 50x50x3 mm min. Ø 500 mm Shaft capacity Ø 35 mm min. Ø 250 mm Power 1.85 kW Bending speed 10 rpm.

Condition: new, saw blade diameter 350 mm capacity 90 degrees: round 115 mm capacity 90 degrees: square 95 mm 180 x 95 mm Working height 925 mm saw blade turning speeds 15 - 90 U/min total power requirement 3,0 kW weight of the machine ca. 0,68 t dimensions of the machine ca. 0,8 x 1,0 x 1,85 m Electro-pneumatic, vertical, linear-guided automatic saw for use of HSS saw blades to make series cuts from 60° left to 45° right steel. The machine also works in semi-automatic cycle. CNC machine with multiprocessor and two with MEP control, latest generation Csdpfefg Rlcjx Aa Nsrb controlled axes that make it possible to achieve 1000 with the same material thickness different cutting programs, each with a different cutting length and number of pieces program.

Condition: used, Year of construction: 1983, Technical details: Pressure: 160 t throat: 360 mm max. ram stroke: 500 mm distance table/ram: 800 mm clamping plate on table: 1250x630x100 mm passage opening in table: 4x Ø 62mm mm ram speed - forward: 200 mm/s ram speed - reverse: 125 mm/S ram surface area: 450 x 850 mm Crsdpfx Aaou Nfvus Nob mortise hole in ram: Ø 49 mm height over floor: 810 mm total power requirement: 17 kW weight of the machine ca.: 7200 kg dimension machine xH: 2,1 x 1,4 x 3,4 m manual counter *

Year of construction: 2009, condition: ready for operation (used), machine/vehicle number: 527, Offer 23035 Technical data approx: - Pressure capacity 30 T. - max. sheet thickness 10 mm - max. punching diameter 105 mm Codolnkc Ujpfx Aa Njrb - punching capacity - e.g. steel sheet : 105 mm in 1,5 mm ; 45 mm in 5 mm - e.g. VA - sheet metal : 90 mm in 1,5 mm ; 45 mm in 4 mm - stroke 7 - 70 mm - throat 560 mm - maximum stroke rate 120 H/min - single stroke / continuous stroke - drive 400 V / 4 kW - space requirement approx. W 8000 x H 1850 x D 1700 mm - weight approx. 1900 kg - with: - stop table with stops - foot switch; - emergency stop button - punch quick change device - various receptacles for punches and dies

Condition: new, maximum load weight: 49,000 kg, overall weight: 60,800 kg, axle configuration: > 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 r 17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with beveled corners at the front 45° and with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area in extendable version: -Loading surface in extendable version with rear bevel of approx. 1,000 mm x 8° -5 pairs of lashing rings can be folded outwards (LC 5,000 daN) -3 pairs of lashing rings can be folded outwards (LC 10,000 daN) -1 pair of lashing rings lying in the front of the cargo bed (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps. (LC 2,000 daN) -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Removable two-part ramps: -A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable -Maximum load per pair: 40,000 kg Seat posts: -JOST fifth wheels (mechanical) with 2-speed gearbox for 24 t lifting load (50 t test load) Axles and tires: -BPW axles, two axles rigid two axles self-steering, air-suspended, with drum brake, with lifting/lowering function The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -axle tool -235/75 R 17.5 tires Brake system: -brake system in accordance with EU regulations with EBS-E (4S3M) Steel construction: -steel construction made of high-strength fine-grained steels -Steel grades: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690MPa) Coating: -First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in nova grey Electrical system: -Electrical system in accordance with EU regulations, 24 volt ASPÖCK-NORDIK lighting (ASS3) Cedpfeh Etf Rox Aa Njrb ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Accessories included: -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -One spare wheel with holder in front of the bulkhead -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon -Cover plates to bridge the gap between ramps and cargo bed -White reflector tape in accordance with EU regulations on the sides, on the extension and red at the rear -Electric hydraulic unit -On the gooseneck and on the ramps on the left and right a holder for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -One mud flap at the rear of the trailer -Manual and description on USB stick -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -4 pairs of WADER container pockets in the loading area for one 20ft, 2x 20ft or one 40ft container -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Galvanized extensions, extendable by approx. 230 mm per side -Lift axle on the front axle with controls -Square climbing rails 20 x 20 mm -BEKAMAX central lubrication system -Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm