Bollegraaf HBC60A (30kW)

Bollegraaf HBC60A (30kW)

Condition: ready for operation (used), Baler Hsm vk 42/1200 fully automatic Fgedpera Nrxsfx Aa Nob Pressure force: 42 tons Beam dimensions: 700 x 800 x 600 - 1200 mm Beam weight: approx. 450 kg Press length approx. 7 meters press weight approx. 6000 kg tying 4 x wire automatically

Condition: like new (used), Year of construction: 2023, operating hours: 2,400 h, functionality: fully functional, machine/vehicle number: R40410, power: 371.43 kW (505.00 HP), empty load weight: 75,000 kg, cutting force: 900 t, COPEX REFLEX 900 ton mobile diesel shear baler (year 2023). Maintenance carried out by the manufacturer. Output: 10 to 22 t/h depending on the type of scrap to be sheared. Immediately available. Fodpfxjxg Ekfs Aa Negb

Condition: reconditioned (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: W230-028, pressing force: 80 t, warranty duration: 24 months, pressure: 250 bar, power: 45 kW (61.18 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler. This is a baler HBC80 (45kW) with crosswires. At the time of writing this baler is being completely refurbished in our refurbishment workshop. This refurbishment takes place on the basis of the very strict Bollegraaf OEM Refurbishment Guidelines. Fsdpfx Aotvat Toa Nsgb After refurbishment, this baler is sold with a 2-year warranty.

Condition: excellent (used), Year of construction: 2014, operating hours: 37,656 h, functionality: fully functional, pressing force: 85 t, filling opening width: 1,500 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 650 kg, overall weight: 25,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2024, volume flow: 410 m³/h, transport width: 2,400 mm, transport length: 9,300 mm, Hello, We are offering you a used baler from the manufacturer Presona AB, type LP 85 VH1, subject to availability. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot guarantee their accuracy or completeness. Manufacturer: Presona AB, Sweden Type: LP 85 VH1 Year of manufacture: 2014 Total operating hours: 37,565 hours, as of March 2025 Main press force: 85 t Specific press force: 100 N/cm² Pre-press flap force: 28 t Feed chute dimensions: 1,500 x 1,100 mm Filling volume per press cycle: 2.7 m³ Throughput under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Drive power: 55 kW Tying system: 5-fold vertical Hydraulic oil tank volume: 1,000 L Press dimensions: 10,350 x 2,400 x 3,150 mm (L x W x H) Press weight: approx. 25 t Note: The machine was used for compaction at a recycling plant. Used for the production of paper, cardboard, films, and plastics such as bottles, buckets, canisters, and drums. The press is in good condition. Many wear parts and entire assemblies have been replaced over the past three years. The machine has been regularly serviced. We would be pleased if this press is of interest to you. Fedpfsv T I Evox Aa Nsgb Your service team at Mertens & Frowein GmbH

Condition: good (used), Year of construction: 1981, functionality: fully functional, Equipment: documentation/manual, Automatic channel baler BOA Continu 25 LB + conveyor belt. The baler is in good condition and has been regularly serviced. Recently, the Denison pump underwent a complete overhaul. Fully functional and in continuous operation. Please contact us for further information. Fodsw S Tv Uepfx Aa Nsgb

Condition: excellent (used), Year of construction: 2014, operating hours: 8,900 h, machine/vehicle number: LP50VH2, 1) Technical specifications Press with conveyor Technical data baler: Manufacturer Presona Typ LP 50 VH2 Year of construction 2014 Fgedpfx Aasyrhi No Nsb Press power main press 50 tons Specific press force 63 N/cm2 Feed channel 1,500 x 1,100 mm Filling volume 2,7 m3 Theoretic throughput capacity 730 m3/hour Throughput capacity under operating conditions 340 m3/hour Bale size 1,100 x 720 mm, lenght variable Drive power 45 kW Tying system 5-fold, vertical, fully automatic Throughput capacity at a • bulk weight of 30 kg/cbm 8 up to 10 tons/hour • bulk weight of 50 kg/cbm 11 up to 13 tons/hour • bulk weight of 100 kg/cbm 15 up to 22 tons/hour Bale density (paper, newspaper) 400 up to 550 kg/m3 Filling volume hydraulic oil tank 600 l Weight baler 16 tons netto Scope of delivery: Press, electrical cabinet, control panel, chain conveyor The documentation (operating manual, CE declaration, electrical/hydraulic diagram) is complete. Visiting is possible by appointment. We are not responsible for technical information or any errors. Upon request, we can send video materials of the working press

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Fodpfx Aasx A U Ncs Nsgb Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: reconditioned (used), Year of construction: 2000, operating hours: 32,169 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,320 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 22,000 kg, oil tank capacity: 900 l, For sale is a complete baling system consisting of conveyor technology, baling press (partially refurbished and tested) and wire stations. Technical data baler: Manufacturer Bollegraaf Recycling Machinery B.V. Typ HBC 60A Year of construction 2000 Hours of operation 32,169 hours, stand November 2024 Press power main press 60 tons Press power of pre-press max. 25 tons Feed channel 1,320 x 1,100 mm Theoretic cycle time 18 sec. Bale size 1,100 x 720 mm, lenght variable Fgsdpfx Ajviwdmja Njb Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical Throughput rate at a bulk weight of 30 kg/cbm approx. 5,5 tons/hour bulk weight of 50 kg/cbm approx. 10 tons/hour bulk weight of 100 kg/cbm approx. 16 tons/hour Bale weight 400 up to 750 kg, depends on material SPS controller Telemecanique TSX Micro Machine weight baler approx. 24 tons Scope of delivery: 1 piece chain belt conveyor 1 Bollegraaf HBC 60A baler with whirling unit 1 maintenance platform with access ladder 2 wire stations with deflection rollers for 10 wire reel stands (without wire) The following repair and overhaul work was carried out: Hydraulic oil tank emptied, cleaned and refilled with new oil Oil filter and air filter replaced Hydraulic block partially resealed Hydraulic hose on hydraulic block replaced Wire entry marks on the floor passages welded shut and smoothed Tying unit cleaned, serviced Electrical system repaired, door flap contact switch partially replaced Whirbulator repaired General maintenance work carried out, lubricated Machine tested during operation, without the use of materials, in manual mode and in automatic mode, see function video Comments: The system has already been completely dismantled, stored and is available for loading at short notice. The documentation (BA, CE, electrical/hydraulic circuit diagram) is available. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: new, Year of construction: 2025, Turbo mill MTR-800 The turbo mill is designed for grinding, knocking out, granulating of materials in order to improve the quality of final separation in further recycling processes. Technical date: - Installed power –75kW - Chamber width – approx. 910mm Fsdpsv I S Uksfx Aa Njgb - Chamber diameter – approx. 620mm - Number of abrasive knives – approx. 89 pcs. - Number of abrasive counterknives – 18 pcs. - Structure placed on adjustable vibration isolators - Dimensions – 2200 x 1600 x 1550mm - Chamber opening by means of a manual hydraulic pump - Engine base with a rocker tensioner - Weight – approx. 1950kg- -Discharge ended with an orifice fi-150 -Electrical installation with inverter included in the price.

Condition: reconditioned (used), Year of construction: 2014, operating hours: 24,967 h, functionality: fully functional, machine/vehicle number: 004283-0030, pressing force: 122 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, warranty duration: 24 months, year of last overhaul: 2026, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler. This is a baler HBC120s (90kW) with crosswires. At the time of writing this baler is being completely refurbished in our refurbishment workshop. This refurbishment takes place on the basis of the very strict Bollegraaf OEM Refurbishment Guidelines. Fgsdpfx Asxcir Eja Neb After refurbishment, this baler is sold with a 2-year warranty.