Shaft Alignment Machine

Cimat RT 505 CMT-300H2W

Condition: new, functionality: fully functional, Year of construction: 2026, roller (bottom) diameter: 310 mm, roller (top) diameter: 320 mm, roller diameter: 310 mm, roller length: 1,550 mm, working width: 1,500 mm, sheet thickness steel (max.): 38 mm, overall weight: 12,500 kg, total length: 4,500 mm, total width: 2,300 mm, total height: 1,740 mm, power: 18.39 kW (25.00 HP), working length: 1,500 mm, Equipment: documentation/manual, emergency stop, FACCIN HAV 15342 variable three-roll bending machine Electronically controlled, hydraulic three-roll bending machine Technical data: Number of rollers: Three Geometry of the side rollers: variable Working width: 1550 mm Dkedpfx Ast Akt Rodror Top roller diameter: 320 mm Side roller diameter: 310 mm Pressure force against the top roller: 160 tons Working pressure at nominal force: 250 bar Guaranteed installed power: 18 kW (25 hp) Guaranteed maximum rotation speed: 3.5-7 m/min Guaranteed machine weight: 12,500 kg Length: 4,500 mm Width: 2,300 mm Height: 1,700 mm Guaranteed performance: for material with yield strength 260 N/mm² Rolling capacity (full working width) 38 mm Bending capacity (full working width) 20 mm from pipe diameter 1,600 mm Rolling capacity (full working width) 30 mm Bending capacity (full working width) 17 mm from pipe diameter 415 mm Standard equipment: Variable geometry with linear guides for roller movement Extra long folding bearing for increased frame stability Electronic parallelism system EPS Hardened rollers for high wear protection All rollers ground after heat treatment Siemens S7-HMI PLC control system PGS-CLASSIC control system with Siemens touch panel Hitech hydraulic and electrical package Simultaneous rotation and roller movement Safety ripcord with emergency stop and CE certification Central lubrication Water cooling for the hydraulics Cone bending device Prepared for retrofitting of supports and roller conveyors FACCIN Advantage Package AP

Condition: new, cutting diameter 355 mm dimensions of saw-band 3770 x 34 x 1,1 mm cutting speed 20 - 80 m/min cutting width 490 x 280 mm 290 mm Impact energy 250 mm 230 mm 180 mm connected load frequency 400 Volt total power requirement 2,2 kW weight of the machine ca. 0,7 t dimensions 1,43 x 0,72 x 1,7 m Semi-automatic miter band saw Dksdomhm Aqspfx Adror - Miter cuts up to 45° left + right - Miter cuts up to 60° right - Vice with quick release device - Tape tension control via manometer - Electr. automatic cooling

Condition: good (used), functionality: fully functional, Year of construction: 2005, machine/vehicle number: MC0 35100, control type: CNC control, degree of automation: semi-automatic, actuation type: hydraulic, roller diameter: 1,000 mm, sheet thickness (max.): 130 mm, sheet thickness steel (max.): 130 mm, total length: 3,500 mm, power: 240 kW (326.31 HP), Technical details Max. bending width: 3,500 mm Max. sheet thickness: 200 mm Dedpfxeyn Agbe Adrjkr Total power requirement: 160 kW Smallest roll-in diameter: 770 mm Maximum cylinder pressure: 2 x 2 t Top roll Ø1000 mm Bottom rolls Ø900 mm

Condition: used, FARINA hydraulic press brake, 5000 x 100 tons, throat depth 400. Dimensions: 555 x 220 x 290 (H), weight 15,100 kg (151 quintals). Djdpsfrllqjfx Adrskr

Condition: ready for operation (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: 11311, workpiece weight (max.): 30 kg, type of input current: three-phase, input current: 12 A, input frequency: 50 Hz, input voltage: 400 V, rotor diameter: 1,000 mm, Balancing Machine, vertical shaft. Measurement in two planes. Maximum rotor weight: 30 kg (tooling included). Automatic Indexing (rotor will, after measurement be positioned with correction location at the front). Rotor speed can be set for each programmable standard workpiece type. Some tooling is included. Dodpfx Aex H Aa Todrskr Machine is available because fans are no longer built by the customer.

Condition: used, plate width 2500 mm Dkjdpfxohpva Dj Adrer plate depth 5100 mm plate height 400 mm weight ca. 9 t required space 2,5 x 5,1 x 0,40 m

Condition: used, Year of construction: 1995, documentation vorhanden dimensions of the machine ca. 4,10 × 1,20 × 1,40 m Dksdpfx Adjyhrcrerer

Condition: used, Used 2 MW wood biomass power plant built in 2009 and running until February 2023. Plant is made up of a steam boiler that uses forest waste as fuel and a condensing steam turbine generator, electrical room, control room. Main equipment includes: Dodpoyhc Irjfx Adrjkr - Biochamm BCV-11.0000 CA biomass boiler built in 2008 with approximately 23,665 hours of use. - Boiler feed system made in 2008 with approximately 22,549 hours of use. - Atlas Copco compressors made in 2008. - Water treatment plant made in 2008. - Hamworthy condenser made in 2008 with 22,539 hours of use. - Siemens SST-110 (TWIN AFA46 GT6) steam turbine made in 2008, with 22,539 hours of use and 563 starts. - Leroy Somer L57 54 m7/41 alternator made in 2008 with 22,539 hours of use. - EWK cooling towers made in 2008 with approximately 23,102 hours of use. - Fivemasa HVAC made in 2008. Available for relocation or in-situ with land and buildings.

Year of construction: 1980, condition: used, The Sledum RG-270 is a high-precision, industrial-grade crankshaft grinding machine developed for the precision grinding of crankshafts in internal combustion engines and the journal surfaces of similar rotating components. The machine is built on a massive cast-iron machine bed, offering high stability and vibration damping. The design enables uniform, high-precision machining of large crankshafts. Key Technical Features: Distance between centers: 2000 mm Maximum swing radius: 270–275 mm Machinable parts: crankshafts, shafts, eccentric rotating components Grinding spindle with high-rigidity bearings Fine-feed cross and longitudinal slide system Machine bed with precision guide rails Adjustable steady rest system for stable support of long workpieces High-power grinding motor for continuous industrial operation Manually controlled feed and positioning system Stable, vibration-damped industrial machine frame Coolant system with preparation/conditioning unit Heavy-duty industrial construction, designed for long service life Accessories and Equipment: Complete headstock and tailstock (counter-spindle) system Grinding spindle unit with grinding wheel mount Adjustable steady rests for long shafts Workpiece clamping system Dsdpfx Adezbiblerjkr Precision alignment and centering components Grinding wheel mounting flanges Workpiece rotation mechanism Manually controlled operator panel Complete slide system with fine feed Coolant connection points Machine body and industrial machine bed Adjustable workpiece support units

Condition: used, Year of construction: 1961, workpiece weight 300 kg workpiece length 1200 mm diameter 1300 mm The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are Dkodpfx Ajy Swhvjdror possible by appointment. We look forward to your visit. Your Markus Hirsch Team