Other machinery

IWT V10-S

Condition: good (used), Maximum log diameter: 910 mm Maximum cutting width: 730 mm Minimum thickness of last board: 25 mm Maximum cutting length: 6300 mm Minimum cutting length: 1200 mm Log weight: 2000 kg Feed speed (steplessly adjustable): up to 47 m/min Output (finished product): 1.8–3.0 m3/h Main motor power: 22 kW Lsdpfx Absxd Tgvsceri Pulley diameter: 600 mm Wood-Mizer saw blade length: 4668 mm Wood-Mizer saw blade width: 38 mm

Year of construction: 1994, condition: good (used), Rivo gang wheel sharpening machine Lrsdpfxjpl D Hxe Abcei Tyop GA 250

Condition: good (used), Year of construction: 1989, Pressing area 2550 x 1350 mm Number of press cylinders #6 Total pressing force 140 t Opening width approx. 400 mm Lredpswd N Rmjfx Abcei Operating voltage: 3 x 400 V + N, 50 Hz. Total connected load approx. 26 kW Space requirement (L x W x H) approx.: 3400 x 1600 x 2000 mm Weight: approx. 5500 kg Hydraulic hot plate press Down-piston design Electric hot platens Pressing pressure continuously adjustable via pressure switch Hydraulic pump Central control panel with all operating and Digital temperature display for both hot platens Press cycle counter Safety ripcord Rack compensation Main switch Note for used machines: • Errors in technical specifications and subject to prior sale. • Subject to change without notice. • Prices quoted are for pickup from the location - free shipping! • The machines have been cleaned and functionally tested. • All machines are sold as seen, without any warranty. The buyer is free to inspect the machines on site. • Special agreements are only possible in writing. (We will only respond to inquiries if you provide your address and telephone number!)

Year of construction: 2023, condition: new, Chopping height max. mm. 200 Infeed width mm. 500 Infeed rollers piece 3 Rotor flight circle mm. 600 Chopping length approx. mm. 20-30 output - output 16 - 20 rm/h chipping Chipper blade piece 2 Lsdpfxencd Aze Abceri Feed motors kW 2x2,2 Weight approx. net kg 4100 Inlet : horizontal machine base : steel, inert gas welded Rotor : steel, inert gas welded, dyn. balanced. Bearing : Oversized roller bearings. Bearing housing : Steel, flanged housing. Feed rollers : steel, special toothed. Chip outlet : underneath the machine. Machine grate : (sieve) for secondary crushing of excess lengths. Drive pulley : Matched to main motor N=1500 min-1 Hydraulic system : consisting of: Hydraulic pump, diaphragm accumulator, cylinder, pressure gauge, control valves for lifting of the upper feed roller. Feeding : by 2 gear motors, Make NORD GEAR

Condition: refurbished (used), Extinguishing water tank according to DIN 14230 (underground extinguishing water tank): 100,000 liter extinguishing water tank for underground storage, single or double walled, 1 manhole DN 600 with blind cover incl. seal and screws, outside with bitumen insulation - second-hand -... tank volume: 100.000 liters / 100 m³ length: approx. 15.750 mm diameter: approx. 2.900 mm weight: approx. 11.600 kg Material: steel material S 235 JRG 2 The tank has an extinguishing water suction connection according to DIN 14244 with a mounted fire department coupling/fixed coupling A according to DIN 14319 in the design form B without gauge connection. Furthermore, the tank has a venting flange connection in NW/DN 100 with cap in a total length of approx. 1,300 mm suitable for 800 mm ground cover and 500 mm above ground. Lrodpfx Aoi Enwvjbcji - The tank is emptied, cleaned and has been provided with a bituminous exterior coating by us at the factory. On request, we can provide the tank with a bitumen-based full interior coating (against corrosion) or epoxy resin interior coating We can offer you a cost-effective delivery with our own truck. Just let us know the place of delivery, you will immediately receive the exact freight costs. An inspection is possible at any time after prior appointment. If you need any further information, just give us a call or send us an e-mail to b.barth(at)barth-tank.de. Trade-in and purchase of tanks/vessels is possible, just contact us. We have such tanks of course also in the following sizes constantly in stock: - 10.000, 13.000, 16.000, 20.000, 25.000, 30.000, 40.000, 50.000, 60.000, 80.000, 120.000 liters.

Year of construction: 2026, condition: reconditioned (used), functionality: limited functionality, machine/vehicle number: 559, Dryer optimized for thick timber or hardwood Lodpfxoya Ik Ao Abceri Usable length: 5000 mm Usable height: 1100 mm Usable width: 1100 mm New electrical cabinet and sensors Controlled drying function Missing external rail and trolley (can be supplied or we will assist the buyer with fabrication) Dryer can be inspected in department 74

Year of construction: 1970, condition: good (used), functionality: fully functional, Stenner RESAW VHL 48 manufacture Stenner UK S/N J2103 year 1970 (original photos coming soon) Principal Dimensions and data: Diameter of saw pulleys: 48"= 1220mm Width of saw pulley face-standard 5" (127mm) Width of saw pulley face-optional 5 1/2" (140mm) Maximum width of saw - standard 5 1/2" (140mm ) Maximum width of saw-optional 6" (150mm)A Minimurn length of saw 25" 8" (782mm) Maximum height of top saw guide above table 28" (710mm) Table height from floor level 31 1/2" ( 800mm 9 Overall height from floor level 9.1" ( 2770mm) Overall width 8.1" (2460mm) Speed of saw pulleys,r.p.m. 8,000 (2440m/min) Horse power range 30 kW Size of fast and loose pulleys 20"x6 1/2" Feed speeds, standard; f.p.m. or m/min. 0-140 (0-42.6m) Shipping Specification : Standard Machine : Net weight, lbs. 3583 kg Lredpfx Aevuhumsbcei The VHL 48 is a band resaw of advanced design embodying many new features resulting from a close study of user-operator requirements, and the necessity to provide fast and accurate sawing coupled with ease of operation, reduced operator fatigue, low maintenance, and increased safety. The design caters fully for these essential factors which contribute to a markedly high level of operating efficiency. The machine is primarily designed for the planning mill and joinery shops. The thin bandsaw gives the machine a high timber recovery rate; the loss due to saw kerf being very low. Compared with a circular radial-arm resaw, the VHL is faster, less wasteful, and uses less power for a given class of work general The VHL is made only as, a left-hand machine, i.e. the saw pulleys run in an anti-clockwise direction when looking in the direction of the feed. The drive is normally arranged to give a saw speed of 8,000 feet permin. (2440m l/min.) Main Drive The main drive is applied to the bottom saw pulley spindle which is prepared for vee belt, flat belt, or flat belt fast and loose pulleys to suit the proposed driving unit. Complete electric motor drives, up to 40 H. P. and for most current supplies can be provided; they include two vee pulleys, set of vee belts, belt guard, motor with slide rails, starter and a master stop button which is fitted to the machine base close to the sawyer's position. horizontal rollers The horizontal rollers are 6" (152mm) diameter and extend the full opening on the fence side and 6" (152mm) beyond the table on the open side; they are normally free-running idle rollers. They can be supplied hydraulically driven as optional equipment, either with the machine or after installation; the rollers are then driven in synchronism with the main feed rolls, by a separate motor. The drive is arranged so that the open-side roller at the outfeed end rotates in the reverse direction to facilitate the return of timber to the sawyer. The roller in front of the saw is moveable sideways to permit rapid saw changing.

Condition: new, Timesavers Series 12 WW The machine is equipped with two belt grinding stations; with station 1 you can perform pre-grinding to remove high burrs and splatter, and with station 2 you can achieve a surface finish on the part. Ljdpfewqf U Ujx Abcori The transport speed of the belts is continuously adjustable. The table opening can be adjusted from 0.8 to 100 mm.

Condition: used, Year of construction: 2018, Used machine Year of manufacture: 2018 Special feature: Machine for up to 100 mm edge height! Condition: Factory-inspected by Lange Maschinenbau Equipment and technical data: - Machine table with 13 running rollers for improved workpiece guidance - Edge feeding, synchronous with belt feed - Edge thickness adjustable via digital counter - Pneumatic roller separation with knife (for cuttable edges) - Three pressure rollers - Belt feed: - 0.25 kW - approx. 1250 mm long - approx. 6.0 m/min - 50 mm wide toothed belt with thick, workpiece-friendly rubber top - Digital counter for height adjustment - Direct glue application to the workpiece: drip-proof glue pot with glue supply from below and rapid heat-up time after standstill - Flush cutting unit: - for front and rear workpiece edges - automatic sensing at the workpiece - pneumatic cutting with knife for cuttable edges - Flush trimming unit - with vertical sensing and horizontal guidance - reproducible setting using digital counters - 2 powerful 0.4 kW high-frequency motors Lrodpfxjwka S Ij Abcsi - stepless speed adjustment from 4000 to 18000 rpm - Cutter Ø 70 mm, Z4, radius 2 mm/15° - central extraction nozzle Ø 100 mm - 2 chip extraction hoods with hose Ø 60 mm - Automatic height adjustment of the upper cutter with belt feed - Continuous workpiece support approx. 1800 mm long - Workpiece support rail, extendable by approx. 300 mm - Rotatable foil dispenser Ø: 800 mm - Workpiece width: min. approx. 80 mm - Workpiece thickness: 10 – 100 mm - Workpiece length: min. approx. 220 mm - Edge thickness: 0.4 – 2.0 mm - Roller separation: max. 1.0 x 55 mm, 2 x 45 mm - Glue pot heating capacity: 2.7 kW - Heat-up time: approx. 10 minutes - Working height: approx. 880 mm - Electrical connection: 400V, 50 Hz, 3Ph + N - Total connected load: 3.8 kW - Pneumatic connection: 6 Bar Dimensions (without foil dispenser): approx. 1800 x 700 x 1300 mm Weight: approx. 260 kg Availability: short-term Location: Flörsheim

Condition: new, Year of construction: 2026, Drum chipper series ATH S&F chippers and drum chippers with horizontal infeed are used in many areas of the wood processing industry (sawmills, timber mills). Chippers from the ‘ATH’ series produce high-quality and homogeneous wood chips with a low proportion of fines from residual wood, for example as quality chips for the cellulose industry or as fuel chips for energy generation ATH 220 series - Feed height: 200 mm - Feed width: 500 | 700 | 1000 mm - Number of chipper knives: 2 - 4 pieces - Number of counter knives: 2 pieces - Rotor diameter:520 mm - Number of feed rollers: 3 pieces - Throughput: up to approx. 40 rm/h * - Chipping length: 5 - 50 mm - Chipper drive power: 22 - 110 kW - Drive power feed rollers: 2 x 2.2 kW - Operating/control voltage: 400/220 V, 50 Hz - Weight: 2,800 - 4,000 kg ATH 330 series - Feed height: 300 mm - Feed width: 500 | 700 | 1000 mm - Number of chipper knives: 2 - 6 pieces - Number of counter knives: 2 pieces - Rotor diameter: 700 mm - Number of feed rollers: 3 pieces - Throughput capacity: up to approx. 70 rm/h * - Chipping length: 5 - 80 mm - Chipper drive power: 37 - 250 kW - Drive power feed rollers: 2 x 3.0 kW - Operating/control voltage: 400/220 V, 50 Hz - Weight: 3,500 - 5,000 kg *depending on chipper length, kW main motor, number of knives, feed Advantages: - Maximum throughput - Low fines content - Low maintenance - Flexible use - Customised production Lodpouz Hmxjfx Abcsri