Used Albert Goecker Kg for sale (67,424)

Condition: used, tank capacity: 5,000 l, GENERAL Equipment: Crane lugs Design: upright Remarks: 1 pipeline inside the tank; heavier internal residues Speed: 100 / 200 RPM Internal diameter: 1,540 mm Total height: 4,600 mm Power: 4.7 / 5.9 kW Agitator: propeller Location: Bremen Nameplate: Volume: 5,000 liters Product-contact material: V2A 1.4301 (AISI304) Condition: used Lhodpoycluqjfx Adweb Cylindrical height: 2,500 mm Last application: paint industry TANK Base design: on legs Number of legs: 4 units EQUIPMENT Manhole / dome: on the top head (DN 500) Outlet: flange DN80 MATERIAL SPECIFICATION Material of legs: stainless steel AGITATOR Voltage: 400 V Bottom bearing: Agitator arrangement: eccentric in the top head

Condition: used, tank capacity: 1,255 l, GENERAL Ledpsyck U Nofx Adwehb Equipment: Ball valve Design: Container Remarks: Frame, Fe (galvanized); Handhole diameter approx. 210 mm; 1 agitator flange and 1 cut-off connection on the manhole cover; Ball valve very stiff (possibly defective) Internal diameter: 1,080 mm Total width: 1,120 mm Total height: 1,700 mm Total length: 1,220 mm Location: Bremen Nameplate: Volume: 1,255 liters Product-contact material: V2A 1.4301 (AISI304) Condition: used Previous use: Chemicals TANK Support type: Frame EQUIPMENT Manhole / Dome: in the top (DN 400), handhole Outlet: DN50 DIN 11851 Note: light residues, signs of use

Condition: used, tank capacity: 1,251 l, GENERAL Equipment: Ball valve Design: Container Remarks: Frame, Fe (galvanized); handhole diameter approx. 210 mm; 1 container is missing the manhole cover, 2 containers are missing the handhole cover (usually the corresponding tension rings are also missing); 1 container with 2 open, cut connections in the upper cylinder area; 1 container with a dented top head and an external pipeline; this pipeline increases the overall width of this container by approx. 130 mm (see photos) Internal diameter: 1,080 mm Overall width: 1,120 mm Lsdpfsyck U Asx Adwohb Overall height: 1,780 mm Overall length: 1,120 mm Location: Bremen Nameplate: Volume: 1,251 liters Product-contact material: V2A 1.4301 (AISI 304) Condition: used Last application: Chemicals VESSEL Mounting type: Frame EQUIPMENT Manhole / dome: in top head (DN 400), handhole Outlet: DN50 DIN 11851 Note: light residues, signs of use

Condition: used, tank capacity: 560 l, GENERAL Equipment: Ball valve Design: Container Remarks: Frame, Fe (galvanised); Handhole diameter approx. 210 mm (one container is missing the handhole cover; this container also has more severe dents (see photos)); ball valves are very stiff to operate (possibly defective) Internal diameter: 1,080 mm Overall width: 1,120 mm Overall height: 1,100 mm Overall length: 1,120 mm Lhjdpfoyck Upjx Adwsb Location: Bremen Nameplate: Volume: 560 litres Product contact material: V2A 1.4301 (AISI304) Condition: used Last application: Chemicals TANK Supporting structure: Frame EQUIPMENT Manway / Dome: in top head (DN 400), handhole Outlet: DN50 DIN 11851 Note: slight residues, signs of use

Condition: used, tank capacity: 1,023 l, GENERAL INFORMATION Equipment: Ball valve Design: Container Remarks: Frame, Fe (galvanized); Diameter of handhole approx. 210 mm; 1 dent in cylinder Internal diameter: 1,080 mm Overall width: 1,120 mm Overall height: 1,550 mm Overall length: 1,120 mm Location: Bremen Nameplate: Volume: 1,023 liters Product-contact material: V2A 1.4301 (AISI304) Condition: used Last application: chemicals TANK Support type: frame EQUIPMENT Manhole/dome: in top head (DN 400), handhole Outlet: DN50 DIN 11851 Lhedpfx Adjyck Uiewob Note: slight residues, signs of use

Condition: used, tank capacity: 8,750 l, GENERAL Design: rectangular Comments: Each tank contains 2 cooling plates inside; 1 manhole approx. 300 x 400 mm in the front bottom; feet equipped with loose, height-adjustable spherical cap screws (possibly not all feet complete; cap screws not included in the total height, total height will increase accordingly if used); feet are slightly off-set Overall width: 1,620 mm Overall height: 2,700 mm Overall length: 2,950 mm Heating/Cooling: available Location: Bremen Nameplate: Volume: 8,750 liters Product-contact material: V2A 1.4301 (AISI304) Condition: used Last use: wine storage TANK Mounting: feet Number of feet: 4 pcs HEATING/COOLING JACKET Temperature control inside: cooling plate Lhedjycktrepfx Adwsb EQUIPMENT Outlet: DN40 DIN 11851 MATERIAL SPECIFICATION Temperature system material: stainless steel Foot material: stainless steel

Condition: used, tank capacity: 1,500 l, GENERAL Equipment: Crane lugs Design: Vertical Remarks: Armaflex insulation in partial areas of the cylinder; manhole approx. 325 x 420 mm; 3 flow breakers and 1 perforated pipe inside the vessel (see photos) Internal diameter: 1,100 mm Total height: 2,700 mm Insulation: available Max. overpressure: 6.0 bar Location: Bremen Nameplate: Volume: 1,500 litres Product-contacting material: V2A 1.4301 (AISI304) Condition: used Cylindrical height: 1,250 mm Last intended use: Biochemistry VESSEL Mounting type: Feet Number of feet: 3 pieces INSULATION Insulation material: Armaflex Insulation thickness: 20 mm EQUIPMENT Manhole / dome: in the cylinder Ljdpjycixgefx Adwjhb Outlet: Flange DN80 MATERIAL SPECIFICATION Feet material: Stainless steel

Condition: excellent (used), Heavy duty wooden pallets with 3 skids accessible from 4 sides length 1680 mm width 1250 mm board thickness 45 mm weight 82,5 kg several available Lhedjl Uvv Tjpfx Adweb

Condition: new, functionality: fully functional, Year of construction: 2022, ATEX rotational valve, 1,5kw- 18rpm. Special heavy duty. SEW drive with cooler fan. Ljdex Dzc Eopfx Adwshb Special knive system. Special 5 line sleeve system. Inert gas adding hole. Possible to buy 2 new, and 5 slightly used valves.

Condition: like new (used), functionality: not functional, load capacity: 6,500 kg, Load capacity 6500 kg Please note: Arm diameter adjustable from 1880 mm to 4550 mm (swivel-out) Space-saving and continuously adjustable, the extension arms can be locked in place Speed continuously adjustable from 0.001 to 5 rpm Motor power 3 kW Torque 15000 Nm Height 800 mm Maximum current transmission 2000 A Weight 4700 kg Lhedpfx Adex Thucsweb with hand and double-foot remote control CE certificate, declaration of conformity, documentation, circuit diagram with original 2016 quotation invoice Current new price approx. €28,000

Condition: like new (used), Dough mixer With paddle Kemper The machine has 2 speeds Bowl and mixer made of stainless steel Mobile unit on wheels Automatic timer Ljdpfx Adsx N Efqowohb Capacity: 180 liters / 120 kg of dough or 75 kg of flour

Condition: like new (used), Spiral dough mixer Capacity: 100 kg of flour 160/180 kg of dough Diosna Container volume: 260 liters Electrical power: 380V / 50Hz / 3N/PE Two timers Two speeds Lsdpex N Ed Tofx Adwjhb Rewind option Half cover with safety switch Wheels with brakes

Condition: good (used), Year of construction: 1973, machine/vehicle number: 73040, Embossing press Baier GEBA 1/F, installation height 90 mm, pressure capacity 800 kg, working size 10cm x 14 cm, built in 1973, machine number 73040, in good condition, immediately available If you are interested, we would be happy to inform you about other machines in our company. You are welcome to view the machine in our company by prior appointment. Ljdpevt Rpqsfx Adwjhb

Condition: used, Year of construction: 1989, Technical details: length: 12 200 mm Lsdpju N Anhefx Adwehb width: 2 500 mm height: 2 600 mm weight of the machine ca.: Eigengewicht ca. 4,5 t 2 pieces containers, 40 feet, heated Extinguishing system container - insulated container (food refrigerated container) Extinguishing system container with 20.000Liter water tank/tank Mixing station, with corresponding electronics and piping as well as pump station (without pumps) i.D. *

Condition: excellent (used), Professional workshop crane with counterweight and hydraulic drive. Very good condition, fully operational, ready for use. • Model: Hydrobull HB 500 GK • Manufacturer: E. Ziegler GmbH, Renningen (Germany) • Year of manufacture: 2004 • Lifting capacity: 500 kg • Lifting height: 280 cm • Jib length: 150 cm • Counterweight: 850 kg • Own weight: approx. 1200 kg (350 + 850 kg GG) • Outreach range: A1–A7 (240–500 kg, according to load chart) • Steel construction, mobile on industrial wheels • Hydraulic lifting and lowering of the jib • Technical and visual condition: very good Ledpjxmt H Iefx Adwjhb

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: Lsdpfx Adjx A U Ncowohb The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: good (used), Year of construction: 2005, operating hours: 527 h, functionality: fully functional, machine/vehicle number: 05-9473, travel distance X-axis: 2,500 mm, travel distance Y-axis: 1,100 mm, travel distance Z-axis: 60 mm, total height: 2,000 mm, total length: 1,600 mm, total width: 3,800 mm, rotational speed (max.): 12,000 rpm, input voltage: 400 V, The machine in question is a grinding and drilling center (manufacturer designation: stone cutting machine). The machine is designed as a vertical machining center in a gantry design. The frame consists of a welded steel tube construction. The drilling head is mounted vertically. There is no angular adjustment possible on any axis for the drilling head. Tools with horizontal shafts can be attached via an existing angle grinder attachment. The tool can be moved linearly along 3 axes: x, y (horizontal), and z (vertical). The machine table is fixed and does not move. The machine is used for: - Creating cutouts and round edge profiles - Making drip edges or drip grooves, polishing surfaces, polishing edges, and drilling natural stone slabs The machine is also equipped with: - an angle grinder attachment - a compressed air connection (for generating vacuum for clamping fixtures and for cleaning the drill spindle) Lsdsw Upzfspfx Adwohb - a water connection (for cooling tools and workpieces during machining) Machine Data: Manufacturer: Martin Kolb Maschinenbau - Model: Genius 2500 - Serial Number: 05-9473 - Year of Manufacture: 2005 - Max. working area: 2,500 x 1,100 mm - Max. workpiece thickness: 60 mm - Main drive power: 6 kW (400V / 50 Hz) - Spindle speed: 0 - 12,000 rpm (frequency controlled) - Tool holder: 1/2 inch thread - Max. drilling diameter: up to 100 mm Various accessories such as milling cutters and other tool holders are also included.

Condition: reconditioned (used), Year of construction: 2014, operating hours: 5,612 h, functionality: fully functional, pressing force: 48 t, filling opening width: 1,020 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 550 kg, total height: 2,800 mm, overall weight: 12,000 kg, transport height: 2,800 mm, oil tank capacity: 300 l, power: 30 kW (40.79 HP), volume flow: 332 m³/h, Technical information baler: Manufacturer HSM GmbH + Co. KG Typ VK 4812 Year of construction 2014 Hours of operation 5,612 hours, stand August 2025 Press power main press 48 tons Specific press capacity 58,2 N/cm² Feed channel 1,250 x 1,020 mm Theoretic cycle time 11.2 sec. Theoretic throughput rate 332 m³/hour Bale size 1,100 x 750 x 600 up to 1,200 mm Driving motor 30 kW Lhedpfsvtpq Hex Adwsb Connected load 32 kW Rated current 59 A Tying system 4-fold horizontal, fully automatic Throughput rate at a bulk weight of 20 kg/cbm up to 6 tons/hour bulk weight of 50 kg/cbm up to 13 tons/hour Bale weight up to 550 kg, depends on material SPS controller Siemens SIMATIC S7-200 Operating panel Siemens HMI Touch Panel Filling quantity hydraulic oil tank 300 L Oil type HVI 46 Machine installation dimensions with bale chute 10,046 x 4,387 x 2,705 mm (l x w x h) Transport dimensions baler 8,500 x 2,500 x 2,750 mm (l x w x h) Machine weight press approx. 12 t Scope of delivery: Baler HSM VK 4812, without hydraulic oil, without conveyor system. Two wire reel boxes for 8 pieces 40 kg wire reels, without wire Bale chute Machine documentation in German Comments: The press is equipped with an oil cooler and potential-free contacts for external control. The control cabinet is operated from the left in the direction of pressing, the needle unit is located on the right-hand side and can be folded back for transport. The press was partially overhauled and tested in our workshop, see photos and our function video. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagrams) is available in German. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: good (used), Year of construction: 1970, Transformer, transformer, converter, three-phase autotransformer, isolating transformer, 3-phase transformer -PCB containing insulating liquid exchanged in 1998 -Input: 6000V -Output: 400V -Power: 200kVA -Type: LT -(for technical data see photos) -Dimensions: approx. 1300/800/H1600 mm -Weight: about 1000 kg Lsdjb Iqgnepfx Adwohb

Condition: excellent (used), Year of construction: 2024, functionality: fully functional, machine/vehicle number: 360034, Fine grinding machine for various workpieces made of different materials with opposing flat surfaces that need to be ground on one or both sides, e.g., wafers, valve covers For flat honing of workpieces with special height, parallelism, and flatness requirements. Technical data Workpiece diameter: 5–220 mm Workpiece thickness: 0.6–80 mm Warranty 6 months legal warranty Lhodpfx Adjir Ul Sowob

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, machine/vehicle number: 381019, Machine type Planet V7 Machine no. 381019 Technical data Double Disk Grinding Workpiece diameter: max. 180mm Workpiece thickness: max. 100mm Condition Technical quality – very good Optical quality – like new Location Germany Warranty Lhjdpfx Adji Hp U Eewjb 6-month legal warranty

Condition: new, 21.25 m² storage platform incl. stairs, railings on two sides, top edge 300 cm, 500 kg/m², immediately ex warehouse, accessible with pallet truck, system platform, steel platform, storage level Data : - Length: 5000 mm - Width: 4250 mm - Size can be extended on request - Clear height below the platform: 2612 mm - Support grid: 4605 x 3850 mm - Plus 200 mm overhang of the floor covering - Supports, stairs, railing posts, cross bracing & dome struts powder-coated in RAL 7016 - Handrail, knee rail, roll-off edge, main & secondary beams galvanized - Floor covering: 38 mm chipboard P6, OK natural & UK white - New from stock Wietmarschen - AVAILABLE IMMEDIATELY Storage platform consists of : - 04 x upright - 02 x main beam C+350 - 06 x secondary beam S+260 - 01 x intersection - 02 x strut brace Lhedoybaxhspfx Adwjb - 10 x Chipboard - 01 x Stairs, 37° incline - Approx. 8.25 running meters Railing - Incl. connecting material & screws -- IMMEDIATELY AVAILABLE SEVERAL TIMES-- Price : 5026,00 € net 5980,94 € gross You will receive an invoice with VAT shown. Transportation : The delivery is carried out on request by our partner forwarding agency, the costs for this depend on the postal code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation. Are you interested or do you have any questions? Simply contact us by message or phone call. You can find our telephone number on our company page. ☎️ You can reach us by phone from Monday to Friday, 08:00 - 15:00. Alternatively, you can send us a message with your name and number and we will get back to you as soon as possible.

Condition: used, Year of construction: 1984, load capacity: 3,200 kg, Currently 4 units in stock. Single girder semi-gantry crane Manufacturer: Christmann & Pfeifer KG Hoist: Demag Model: PLV 168 NF Lhjdpfx Adsw Ugu Ajwjb Load capacity: 3,200 kg Travel mechanism: Demag Type: 13/6PF 12/4 Usable hook path: 4,800 mm Track gauge (center-to-center): 8,110 mm Weight: approx. 2 t/unit Price per unit, loaded free of charge. The cranes have already been dismantled and are packaged for transport. Machine can be inspected onsite. All information subject to change. Prior sale reserved.

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, KG WETTER CUTTER from 2018 Lodpfjx Ahhljx Adwshb AC motor Fully operational condition If you have any questions, feel free to ask!

Year of construction: 1969, condition: used, Swivel bending machine Albert steel TYpABK 400 /5 Ljdpfxsh Rkh Do Adwehb useful length 2530 mm Sheet thickness 5 mm