Used Biesse Rover 24 L for sale (340)

Condition: used, Year of construction: 2018, Numerical Control BH 660 with BIESSE BSolid software bEdge module for edge management bSolid surface design Sophia - IoT Connection Office control Working range on X-axis mm 3228 Working range on Y axis mm 1580 Working range on Z axis mm 200 with H74 mm suction cups Working range on Z axis mm 245 with H29 mm suction cups No. 8 adjustable ATS panel support bars Installation of the pneumatic lock divided into two zones in Y No. 6 Pneumatic Bakelite bars for panel lifting No. 3 adjustable suction cups for bar Set-Up Assistant for Suction Cups No. 1 electrospindle (pantograph) with 4 axes, automatic tool change, KW 13 (HP 17.4) motor, cooling liquid, HSK cone attachment, 20000 RPM Automatic tool change with 16 positions on the X-axis of the carriage Drilling tesa BH17 independent spindles arranged as follows: No. 5 independent spindles for vertical drilling in the "X" direction No. 5 independent spindles for vertical drilling in the "Y" direction No. 4 spindles for horizontal drilling in the "X" direction No. 2 spindles for horizontal drilling in "Y" direction No. 1 blade integrated into the drilling head diam 120 mm (useful cut 25 mm) GU60L gluing unit for EVA glue with pre-melter - edge pressure system with double rubber roller for spokes maximum internal 30 mm and edge joint sensor - 500 ml glue pot installed on the glue roller - lamp edge heating - edge feed system - edge cutting system - possibility of Introduction of the manual edge Plastic edge thickness from 0.4 to 3 mm Wood edge thickness from 0.4 to 2 mm Laminated edge thickness from 0.4 to 1.2 mm Maximum edge width 65 mm Workpiece thickness from 10 to 60 mm Minimum internal radius workable with 30 mm edging Maximum external radius for edging, proportionate to the thickness and stiffness of the edge: * 10 mm with edge up to 1 mm thick * 20mm with 2mm thick edge * 30mm with 3mm thick edge Minimum dimensions of the edging panel 300 x 300 mm Minimum internal diameter for edging: 350 mm with plastic edges less than 1 mm thick and with panel maximum thickness 18 mm 2-position edge storage unit positioned inside the protective casings for edges with maximum thickness 65 mm Finishing aggregate cleaning station with automatic dispensing of special cleaning liquids and with a cleaning cycle No. 1 aggregate for edge trimming / rounding No. 1 EF60A combi aggregate trimmer / edge scraper / glue scraper Todpfx Ajugpwnsirjd Perimeter protection grids Chip evacuation system with motorized belt Liquid cooling system Automatic lubrication system No. 1 vacuum pump of 250 m3/h TECHNICAL DETAILS TO BE CONFIRMED

Condition: good (used), Year of construction: 1992, functionality: fully functional, workpiece length (max.): 3,200 mm, workpiece width (max.): 1,200 mm, workpiece height (max.): 80 mm, Equipment: documentation/manual, CNC milling machine Rover 342 with 1 milling motor, saw blade, and cross-drilling attachments Tedpfezl Uayox Aired is fully functional but has been disassembled by the seller from a closed-down factory.

Condition: good (used), Year of construction: 2014, functionality: fully functional, Equipped with B-Solid software. Maximum workable height: 120 mm Maximum workable length with automatic feed: 3200 mm Tool changer with 22 positions Includes a new Quattro drilling unit. Tjdpfxovr D Sio Airod

Condition: used, Year of construction: 2007, - Working area: X = 4600 mm / Y = 1935 mm / Z = 275 mm - CE safety devices - 8 ATS plate holders - L = 1525 mm - 24 sliding rails - Automatic positioning of 8 plate holders and sliding rails (EPS X-Y) - Conveyor belt for removing chips and scrap - Pneumatic locking system, divided into 2 working areas in X - 8 rear reference stops with a stroke of 115 mm Tsdpfx Ajzux Nwjirod - 8 stops with a stroke of 140 mm, positioned at 1175 mm (L = 1280 - 1525 - 1800 mm) - 8 stops with a stroke of 140 mm, positioned at 770 mm (L = 1280, 1525, 1800 mm) - 4 lateral stops with a stroke of 140 mm (2 left + 2 right), including pneumatic system. - 4 removable center stops with a stroke of 140 mm (2 left + 2 right), including pneumatic system. - Sensor for detecting lowered stops. - Pneumatic system for lifting rod holders. - 6 lifting rod holders for easy loading - H = 74 mm modules. - Vacuum system for a 250 m3/h pump - 250 m3/h rotary vane vacuum pump for standard vacuum system Composition C3-A1 - Device for mounting a chip deflector with a pneumatic or inductive sensor on a 5-axis machining unit. - Flange for mounting aggregates on a work unit with 5 interpolating axes. *Aggregates can only be used if the spindle is in the vertical position. Composition C3-P2 - Additional Z-slide for rear work units, controlled by an independent Z-axis - 16 vertical and 4 horizontal drilling spindles in the Y direction - Chain-type tool changer with 22 positions at 180 mm center distance - Iron gripper for chip deflectors with pneumatic or inductive sensor, positioned in the chain-type tool changer - RH chip deflector with inductive sensor for standard spindle or 15 kW 5-axis spindle * requires the device for the chip deflector * requires the flange for mounting aggregates when using a 5-axis spindle * requires the C-axis when using a standard spindle - Liquid cooling unit for liquid-cooled systems, can cool two spindles or one spindle and a liquid-cooled drilling head. - Automatic lubrication system - Control unit with 5 interpolating axes. This unit enables numerically controlled interpolation of the spindle on 5 axes. The spindle has high power while simultaneously having reduced dimensions. Note: - Additional overhauled 5-axis main spindle - 8 horizontal drilling spindles, 12 vertical drilling spindles, and nut saw are out of order.

Condition: excellent (used), Working area X: 5,920 mm Working area Y: 1,287 mm Working area Z: 170 mm C, A axes: available Swivel machining: 2 working areas for swivel machining Work table: ATS-HTS-EPS Automatic console positioning system EPS 10 automatically positionable consoles Tsdpfjzxbhwjx Airjd 2 locating pins per console 5-axis milling spindle: Power: 9 kW / 11 kW at 60 Hz Speed: up to 24,000 rpm Tool holder: HSK-F63 Liquid-cooled Drilling head BH 26 16 vertical drilling spindles 4 horizontal drilling spindles in the X direction 2 grooving units for grooves in the X and Y directions Vertical drilling spindles 16, Horizontal drilling spindle X = Tool changer: Chain tool changer with 21 tool positions Clamping systems: Uniclamp clamping system - 6 pieces Control system: BIESSE XP 600 Chip removal: Motorized conveyor belts for the removal of chips and machining waste Vacuum pump BECKER: Motor power 5.5 kW Conveying capacity: 244/286 m³/h Additional equipment: Numerous vacuum suction cups; 6 UNICLAMP clamping systems; Numerous HSK 63 tool holders; 2 large saw blades in the tool magazine Compressed air: 7-7.5 bar Total power: 25.3 kW Weight: 4200 kg

Condition: used, machine/vehicle number: 008112, X axis working area: 3390 mm Y axis working area: 1535 mm Working Table: Pod and Rail Main Electrospindle power: 15 KW Number of controlled axes: 5 axes Tedpfx Ajw Idgvjired Total number of drilling spindles: 21 Total number of tool changer positions: 14

Condition: used, Year of construction: 2013, power: 17.1 kW (23.25 HP), number of axes: 4, working width: 1,320 mm, milling spindle speed (max.): 24,000 rpm, working length: 2,500 mm, TECHNICAL DETAILS Working area, X-axis: 2,500 mm Working area, Y-axis: 1,320 mm Travel, Y-axis: 1,900 mm Max. panel thickness: 170 mm Work table: Cantilever and rail table Number of controlled axes: 4 Travel speed, X-axis: 80 m/min Travel speed, Y-axis: 80 m/min Travel speed, Z-axis: 20 m/min Drilling unit Number of drilling units: 1 Position of drilling unit: top Vertical drilling spindles: 10 Horizontal drilling spindles, X-direction: 4 Horizontal drilling spindles, Y-direction: 2 Total number of drilling spindles: 16 Milling spindle Number of milling spindles: 1 Position of milling spindle: top Controlled axes: 4 Automatic tool changer: yes Motor power: 13 kW Speed: 24,000 rpm Grooving unit Number of grooving units: 1 Position of grooving unit: top Design: fixed, for grooving in the X-direction Max. tool diameter: 120 mm Motor power: 1.7 kW Speed: 7,500 rpm Tjdpfxezmtlkj Aired Number of tool magazines: 2 Tool magazine, rear: 12 slots Tool magazine, side: 10 slots Total number of tool change slots: 22 MACHINE DETAILS Machine programming software: BiesseWorks Number of vacuum pumps: 1 Suction capacity per pump: 90 m³/h Total connected load: 17.1 kW EQUIPMENT CE marking Protective structure for machining units with safety sensors Safety system: front safety mats 4 consoles with suction cups for workpiece clamping 1 drilling unit, top 1 milling spindle, top 1 fixed grooving unit, top, for grooves in the X-direction 1 rear tool magazine with 12 slots 1 side tool magazine with 10 slots 1 vacuum pump Front safety mats The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photographic documentation and technical/commercial documents with a descriptive character. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 8359

Condition: excellent (used), CNC CELL with AUTOMATIC panels handling for routering, boring, cutting and edge banding BIESSE Machine with a movable gantry (on the X-axis)–CNC with “bTouch” screen and “bPad” wireless console Software bSolid+bEdge, connection to SOPHIA, IoT (Industrial Internet of Things) platform N. 10 supports ATS (L = mm 1800), with automatic EPS (Electronic Positioning System) Automatic tool change system (Tools storage plate in X-axis / 16 positions) Useful working area (X - Y - Z) mm 6735 x 1650 x 245 (290) Useful working area (X - Y - Z) in edge banding mm 5780 x 1930 x 60 N. 2 Working areas - Vacuum pump (capacity m3/h 250) - Motorized carpet to evacuate wastes/chips 1st Y-axis)- 2 machining heads (upper) in 4 slots Slot 1 + Slot 2: N° 1 vertical HSK F63 electrospindle (13.2 kW) with C-axis (360°) and air blowers Automatic tool change system (Tools storage plate in Y-axis / 6 positions) Todpszxnphofx Airod N° 16 (or 20) independent vertical drilling spindles + N° 6 (or 8) independent horizontal drilling spindles N° 1 Circular Saw (grooving) 120mm diameter (on the X-axis) Slot 11 + Slot 12: N° 1 vertical spindle HSK F63 (13.2 kW) with C-axis (360°) and air blowers Automatic tool change system (Tools storage plate in Y-axis / 6 positions) N° 16 (or 20) independent vertical drilling spindles + N° 6 (or 8) independent horizontal drilling spindles N° 1 Circular Saw (grooving) 120mm diameter (on the X-axis) 2nd Y-axis - Edge Banding Unit - GU60C Glueing Unit (Hot Melt EVA glue) / Edges (tape) thickness in rolls (min/max) mm 0,4 - 3 Edge coils supporting unit (for 2+2 = 4 reels) 200312) automated panels loading +unloading, using a KUKA robot (moving along the X-axis)

Condition: like new (used), Year of construction: 2019, I sell the edge banding machine Biesse JADE 240 Year 2019. Special offer: Machine almost NEW !! Configuration: Entry fence manual adjustable Premilling pneumatic adjustable Edge banding manual adjustable / 2 glue tanks for EVA glue Pressure zone manual adjustable End cutting saw pneumatic adjustable Tilting radius milling manual adjustable Corner rounding unit 2-motor manual adjustable Radius scrapers manual adjustable Tedpfx Aexncrvoired Glue scrapers pneumatic adjustable Polishing brushes Separation fluid spraying front Central lubrication system Top feeding rolls Height adjustment manual Material height 10-60 mm Edge thickness 0,4-8,0 mm Feeding speed 12 m/min. Only 9250 meters edgebanded. Machine almost NEW !! CE Mark. Including full documentation and CDs. Very good condition ! Available immediately !

Condition: used, machine/vehicle number: 008689, X axis working area: 6735 mm Y axis working area: 1650 mm Working Table: Pod and Rail Main Electrospindle power: 13.2 KW Tedpfeznuxbsx Airjd Number of controlled axes: 4 axes Maximum edge height: 65 mm Total number of drilling spindles: 30 Total number of tool changer positions: 22

Condition: used, machine/vehicle number: 008270, X axis working area: 4320 mm Y axis working area: 1500 mm Working Table: Pod and Rail Main Electrospindle power: 13 KW Number of controlled axes: 5 axes Todpfxezw Dxco Airod Total number of drilling spindles: 23 Total number of tool changer positions: 22

Condition: ready for operation (used), Year of construction: 2011, machine/vehicle number: 65352, functionality: fully functional, travel distance X-axis: 3,765 mm, travel distance Y-axis: 1,585 mm, travel distance Z-axis: 170 mm, number of axes: 3, number of slots in tool magazine: 12, TECHNICAL DETAILS Milling spindle Number of controlled axes: 3 Tool holder: ISO 30 Motor power: 1.7 kW Drilling unit Drilling tool available: Yes Vertical drilling spindles: 10 pcs. Table and working area Type of milling table: Flat table Table length: 3,750 mm Table width: 1,560 mm Working area X-axis: 3,765 mm Working area Y-axis: 1,585 mm Working area Z-axis: 170 mm Z-axis travel max.: 324 mm Material clamping system: Pneumatic Tool changer and control Number of tool changer positions: 12 pcs. MACHINE DETAILS System/Software: BiesseWorks Vacuum pump Brand: Busch Type: MM1322AVM Capacity: 360 m³/h Connection diameter: 60 mm Oil-free: Yes Dimensions & Weight Tjdpfx Ajzuwt Ioirod Dimensions (L x W x H): 5,600 x 2,250 x 2,550 mm Installed length: 6,465 mm Installed width: 4,794 mm Installed height: 2,550 mm Shipping weight: 2,500 kg Shipping packages: 2 pcs. EQUIPMENT Tools included Vacuum pump Busch MM1322AVM Safety mat CE marking

Condition: used, machine/vehicle number: 008272, Position 1: 5 Axis CNC Routers BIESSE + KUKA-ROVER A + KR210 R3100 Tsdpfx Aisx A Tfverod Position 2: Robot BIESSE + KUKA-ROVER A + KR210 R3100

Condition: used, machine/vehicle number: 008377, X axis working area: 3390 mm Y axis working area: 1570 mm Tedpfx Ajx Swb Aoirjd Working Table: Pod and Rail Main Electrospindle power: 13 KW Number of controlled axes: 4 axes Total number of drilling spindles: 32 Total number of tool changer positions: 10

Condition: good (used), Year of construction: 2001, I sell the panel beam saw BIESSE SELCO EB70. Year 2001. Cutting size 3200x3100mm. Cutting height 55mm. Main motor 7,5kW Scoring motor 2,2kW Total area covered W.5422mm x D.6488mm Gripper with pneumatic regulation Side alignment top roller with pneumatic stroke. Optimising software included. Very good condition. Available immediately. Tjdpfez Ii Arex Airsd

Condition: used, machine/vehicle number: 008694, X axis working area: 4320 mm Y axis working area: 1287 mm Working Table: Pod and Rail Main Electrospindle power: 11 KW Number of controlled axes: 5 axes Total number of drilling spindles: 16 Tjdpfx Aiszqz Nxjred Total number of tool changer positions: 31

Condition: not inspected (used), Year of construction: 1999, functionality: unexamined, 24 vertical spindles, 10 horizontal spindles, 7-position tool changer, 8 vacuum worktables with digital position display, interchangeable angle gearbox. Usable length of the workpiece support: 3200 mm, width of the workpiece support: 925 mm. Tjdpfjx Iulwjx Airjd

Condition: used, Year of construction: 2022, - Work surface: 3800 x 2200 mm with rear lifting table - Maximum cutting length: 3800 mm - Saw blade overhang: 108 mm - Maximum gripper opening: 100 mm - Minimum panel size: 1830 x 915 mm - Maximum panel size: 3660 x 2200 mm - Maximum stack height: 630 mm - Minimum thickness on the lifting table: 10 mm - Maximum lifting table stroke: 985 mm Tedpfx Aiozuyl Tersd - Load capacity of the lifting table: 5 t Panel dividing saw Manufacturer: Biesse Type: Selco WNT 630 Year of manufacture: 2022 Technical data - Work surface: 3800 x 2200 mm with rear lifting table - Maximum cutting length: 3800 mm - Saw blade overhang: 108 mm - Maximum gripper opening: 100 mm - Minimum panel size: 1830 x 915 mm - Maximum panel size: 3660 x 2200 mm - Maximum stack height: 630 mm - Minimum thickness on the lifting table: 10 mm - Maximum lifting table stroke: 985 mm - Load capacity of the lifting table: 5 t The machine is almost new and has only been used for a few months. Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2013, Working center with automatic robot for panel loading and unloading management Biesse XP600 Numerical Control with Biesse Works ADVANCE graphic interface software - machine version and version office - WRT technology (Widows real time) the machine control logic is processed directly on the PC and not on a dedicated special device Working field in X axis 6200 mm Working range in Y axis mm 1552 Working field in Z axis 180 mm Z axis travel mm 235 N ° 2 work fields in X axis Bar worktop \ console Todpjkvrxuefx Aired No. 10 EPS electronically adjustable bars for suction cup support N° 8 pneumatic bakelite bars for lifting the panel - loading / unloading aid N° 4 EPS electronically adjustable suction cups for each bar with vacuum seal for fixing the panel during the processing N° 1 vertical electrospindle, with automatic tool change, motor KW 12 - 12000 RPM - flange for aggregates - preparation for C-Axis Vector Automatic tool change system with 12 positions - positioned on the machine head BH35L boring head with spindles arranged as follows: - N° 14 verticals in X axis - N° 10 vertical in Y axis - N° 6 horizontal in X axis - N° 4 horizontal in Y axis Independent blade for making grooves in the X axis - diam. 120 mm Front protection and safety system with carpets Perimeter protection grids Automatic lubrication system Machine control cooling and cleaning system with conditioner Vacuum pump mc / h 250 Kuka industrial robot with 6 articulated axes with point-to-point positioning. Independent control panel Panel alignment table Barcode reader on the robot arm Panel introduction system via: * 1 motorized roller conveyor for panel stack preloading * 1 translating motorized roller conveyor * 1 motorized panel stack unloading roller conveyor Technical features: * Type : KR210-2 * Number of axles : 6 * Admissible nominal load : Kg 210 * Machine weight : Kg 1267 * Sound level: 75dB * Installed power: 25.8 kW * Panel dimensions - Min\max length: mm 300\3000 * Panel dimensions - Min\max width: 180\1500 mm * Panel dimensions - Min\max thickness: 8\60 mm * Max panel weight: Kg 90

Condition: good (used), Year of construction: 2013, Edge thickness Roll 0.4/3 mm / Straps 0,4/22 mm Workpiece thickness 10-65 mm Workpiece overhang 140 mm Feed sppeds 10-14-18-20 m/min Equipped with Twin edge milling unit Gluing unit Snipping unit Rough trimming unit Fine trimming unit Profile trimming unit Universal trimming unit Flat scraping unit Edge buffing unit " Sintra " control unit Tjdsu Hldmepfx Airod Dimensions (l x w x h) approx. 7000 x 1400 x 2100 mm Weight approx. 3600 kg Machine number 94391 Year of construction 2013 CE

Condition: used, Year of construction: 2017, Edge banding machine Manufacturer: Biesse Type: Jade 240 Year of manufacture: 2017 Technical data Note: Tsdpezuyixefx Airsd [b]The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.[/i]

Condition: ready for operation (used), Year of construction: 2022, This BIESSE Selco WNT 630 panel saw was manufactured in 2022. It features a maximum cutting length of 3800 mm, saw blade projection of 108 mm, and a lift table capacity of 5 tons. Ideal for handling large panels up to 3660 x 2200 mm. If you are looking to get high-quality cutting capabilities, consider the BIESSE Selco WNT 630 machine we have for sale. Contact us for more information. • Working size: 3800 x 2200 mm • Max cutting length: 3800 mm • Saw blade projection: 108 mm • Max gripper opening: 100 mm • Min panel size: 1830 x 915 mm • Max panel size: 3660 x 2200 mm • Max packet height: 630 mm • Condition: Almost new, used only a few months Additional equipment • Back lift table: • Minimum panel thickness on lift table: 10 mm Tsdpfszug E Hex Aired • Maximum lift: 985 mm • Lift table capacity: 5 t

Condition: good (used), Code: 0510 Brand: BIESSE Model: POLYMAC SINGLE 89 - N - CE Standard Tsdpo Agcf Refx Airod Edgebander for straight, shaped, and round panels, for Pvc, Abs, veneer, and wood edges, for woodworking shops, custom furniture, furniture, kitchens, shelves, and various applications - CE Standard Features: Motorized feeder with adjustable speed Pneumatic trimming unit for trimming edged panels Digital electronic counter for setting the desired cutting length Work surface tilting from 0 to 45° Adjustable edge feed speed Technical Data: Edge height 10-60 mm Edge thickness 0,4-3 mm Min radius 20 mm Min panel length 300 mm Feed speed 2-18 mt/min Total power 4 Kw Compressed air 6 bar Overall dimensions mm 1700 x 950 x 1300 h Weight kg 350

Condition: good (used), Year of construction: 1997, 3-AXIS MACHINE FOR DRILLING AND MILLING OF CABINET FURNITURE PARTS, WITH AUTOMATIC TOOL CHANGER FOR MILLING TOOLS Working area: 2,893 x 950 mm Maximum workpiece height: 65 mm Number of workpiece supports: 6 Number of vacuum cups per support: 2 1 milling motor, 6.8 kW Clearance height between tool holder surface (motor) and top edge of vacuum cup: approx. 250 mm 2 tool changers: 3-position traveling and 4-position lateral Grooving saw fixed in X axis Number of vertical drilling spindles: 10 Number of horizontal drilling spindles: X 2 + 2, Y 1+1 Vacuum pump 100 cbm/h Controller: NC 410 Todpfx Ajy Iaiheired Safety tread mat in front of the machine

Condition: good (used), Year of construction: 2006, I sell the widebelt sanding machine Biesse Regal 520 - 1350, year 2006. Configuration: 1pc. electronic segmented pad 1pc. electronic segmented pad Working width 1350mm Pressure rollers for short elements. Tedpjzkmdhefx Airjd Air-blow on both units. Total weight 3050kg Condition very good. Available immediately.