Used Blow Moulding Machine for sale (65,909)

Condition: like new (used), functionality: fully functional, machine/vehicle number: SBO 6/10, Sidel Stretch Blow Moulding Machine Max. output: 6.000 bottles/hour. Max. bottle size: 3.000 cc. Blow stations: 6. Machine is in very good conditioning and well maintained. GENERAL INFORMATION The SBO 6/10 has 6 molds and 10 heating modules. Will work with a wide range of bottle sizes and styles from 0.25 to 3 liters. Sidel 2-step ^PET stretch-blow molders require previously manufactured preforms be supplied to the machine. Separating the bottle manufacturing and preform manufacturing processes allow production to be optimized, provide greater flexibility of operation and use, and provide higher production output rates and yield. MAXIMUM PREFORM DIMENSIONS Neck height 9 – 41 mm (measured from bottom of support ring) Minimum inside diameter of neck 19 mm Maximum outside diameter of neck 34 mm Preform support ring diameter 29 – 51 mm Maximum preform length 210 mm MAXIMUM BOTTLE DIMENSIONS Maximum bottle diameter 130 mm Maximum bottle height 380 mm Bottle capacity 0.25 – 3 liters Knedpfx Akeg Ailcslja AVERAGE PREFORM WEIGHTS (non carbonated and carbonated liquids) 0.25 liter bottle 14-20 grams 0.50 liter bottle 20-33 grams 1.00 liter bottle 26-40 grams 1.50 liter bottle 35-51 grams 2.00 liter bottle 44-58 grams 3.00 liter bottle 68-84 grams BLOW WHEEL Height 3.5 meters Number of molds 6 Closing force 10 tons Item height (under neck) at outfeed 1.4 meters approximately Machine DC drive motor power 4 KW HEAT CONDITIONING Height 2 meters Number of oven heating units 10 Number of heating zones per unit 8 Maximum power 170 KW ELECTRICAL USAGE Maximum supplied power 200 KW Average consumption 100-150 KW/hr (varies per bottle being produced) COMPRESSED AIR Supplied power from 7-35 bar Pressure 7 bar Flow rate 50-100 Nm3/hr (varies per bottle being produced) Blow pressure – champagne base up to 25 bar Blow flow rate – champagne base 110-550 Nm3/hr Blow pressure – petaloid base up to 35 bar Blow flow rate – petaloid base 155-770 Nm3/hr CHILLED WATER Temperature 10-12 degrees Centigrade Pressure 5-6 bar Flow rate up to 6 cubic meters/hour Kcal to be removed up to 16,000 Kcal/hour WEIGHT Blow wheel with molds 8 tons Heat conditioning unit 2.2 tons Preform feeder 0.65 tons Electrical cabinet 0.85 tons PREFORM HEAT CONDITONING The preforms are transferred neck up to the heat conditioning device. This unit continuously insures the preforms are inverted before passing, neck down, in front of the heating units and then inverts them again. During the heating phase, the preforms are rotated and their necks protected from the heat in order to optimize the distribution of heat without deforming the neck. Heating is insured by 10 heat modules. Each unit can accommodate up to 8 infrared lamps stacked horizontally whose ends are air cooled. The heating power of 8 zones, corresponding to the 8 rows of lamps, can be controlled in order to optimize the heat profile. These zones are regulated on all SBO Models. After heating, a control by infra-red camera of preform temperature enables regulation of the zones under control, thus insuring maintenance of the required temperature.

Condition: used, Stretch blow molding machine by Etek ISBM line = Injection stretch blow molding Stretch blow molding machine for single-use PET bottles made from PET preforms Stretch blow molding machine for production using the rotary process Ksdpfjkucxljx Aklena Manufacturer: ETEK / GF-Industries, Type Supra 800 sv 1 Serial number: 22000225 Year of manufacture: 2012 Power: 90 kW Mains connection: 400 volts, 50 Hz Weight: approximately 6000 kg In like-new condition

Condition: good (used), Year of construction: 2017, functionality: fully functional, LINEAR PET BLOWING MACHINE SET with auxiliary equipment AC ARCOR - multiBlow2 - 2017 Speed: 1,5L - 6000 Cavities: 4 Formats: 0,1 - 3,0L AUXILARY EQUIP 1. Chiller - M.T.A S.p.A - TAE EVO 051 2. LOW Pressure compressor - SHAMAL 45kw 3. Receiver tank - Low pressure - MAX 16Bar 4. Receiver tank - High pressure - MAX 45Bar Knedpfx Akjquuvrslja

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, machine/vehicle number: 13-13, The BLOMAX 4 Blowmoulding machine is of the model 13-13. The machine has no defects and operates in excellent condition with full functionality. Power : 400V/150A/60000W Knjdpfx Ast Akgwskloa Year of construction : 2000

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, ID BYP01 We sell a used Chinese - PP melt-blown fabric extrusion line for melt blown, make: Zhangjiagang Sevenstars Machinery Co., Ltd., MFG 2020. It was used for a short time. excellent condition. All EU import duties have been paid. Output max 400 kg per 24 hours. General description: 1. Product size: PP melt blown fabric with width at 600mm (after trimming 17m*3) 2. Main Material: PP compounding material 3. Extruder type: SJ65/33 single screw extruder 4. Output capacity: 350-400kg/24hour 5. Electric power supply: 3phase, 380V; 50Hz 6. Additional equipment: • Vacuum feeder • Raw material dryer • Mesh manual filter • T-mould for melt blown fabric • Static electrical discharge equipment • Belt type forming 850mm • Collecting device • Winder and slitting Model L/D Output Speed of Screw Rotationl Power Center Height Knsdpfx Aksuiq Dhjloa SJ-65 10-33 80-150kg/h 20-120r/min 18.5kw 1000mm This line contains the following machines: Automacic vacuum loader ZJ-400 and hopper dryer make RHONG model RDM-25, MFG 2020; Single screw extruder, model SJ65/33, MFG 2020; Heating oven for hot air, model HJGF101-4, MFG 2020; Extrusion T-mold, model: SUS630, made in Japan, MFG 2020; Forming device, MFG 2020; Winder & slitting system, MFG 2020; Oil free air compressor, MFG 2020; The PP melt blown nonwoven production line is a polymer melt extruded from a screw extruder. The polymer is extremely stretched by high-speed hot air or other means to form very fine short fibers, which are aggregated to A web is formed on a roller or a screen curtain, and is finally reinforced by self-adhesion or thermal bonding. Its unique properties are widely used in mask filter materials, thermal insulation filling materials, medical health materials, wiping materials, etc. The finished product can pass the N95 standard as the core material of the mask. Process of melt blown nonwoven production line Polymer preparation --- Melt extrusion --- Metering pump --- Melt blown die head assembly --- Solution thin-flow drawing --- Fibber cooling --- Auxiliary network --- Electrostatic electret --- Reinforced finished product. Melt-blown cloth is produced by melt-blown process. The equipment mainly includes: screw extruder, melt pump, screen changer, melt-blown device, winding device, air system (hot air blower and heater), etc. The function of the screw extruder is to melt the slice material; the role of the melt pump is to accurately measure, control the output and the fineness of the fiber, and continuously and evenly transfer the melt to the spinneret. The function of the screen changer is to filter out impurities in the melt so as not to block the spinneret holes. The function of the winding device is to pack the melt blown cloth into rolls. The function of the air system (hot air blower and heater) is to provide the temperature and pressure of the hot air used in the drawing of the spinning air stream. Price Euro 39.200 Euro + VAT, negotiable, FCA: Oradea / Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: repair required (used), Injection moulding machine, Engel ES 330/85, Used machine Knjdpfxsukn S He Aklea As shown in the pictures, its working condition is uncertain. Overall dimensions :3100 x 1950 x 2600 mm Weight: 5500 kg Manufacturer: Engel Type: ES 330/85 Year of manufacture: 1997 Electrical data: 380V, 60 A, Contoller cards: Keba PS 244; Keba DO 321; Keba DO 321; Keba DO 321; Keba DI 325; Keba DI 325; Keba DI 325; Keba TT 081; Keba AR 181; Keba PD 242; Keba CU 211

Condition: used, Year of construction: 2008, operating hours: 35,000 h, clamping force: 100 kN, displacement volume: 51 cm³, injection pressure: 2,800 bar, overall weight: 5,000 kg, screw conveyor diameter: 25 mm, Freight base: FCA Pegnitz Delivery time: by arrangement Payment terms: 100% before takeover of the machine, net Kedpowlkb Njfx Aklsna

Condition: used, Year of construction: 2001, operating hours: 38,850 h, clamping force: 25 kN, displacement volume: 20 cm³, injection pressure: 1,810 bar, overall weight: 1,900 kg, screw conveyor diameter: 18 mm, terms of delivery: EXW (ex Works) delivery time: on request Knsdpfx Akoyt R S Aelsa terms of payment: 100% prior to delivery

Condition: used, Year of construction: 2001, operating hours: 60,790 h, clamping force: 60 kN, displacement volume: 224 cm³, injection pressure: 2,224 bar, overall weight: 3,350 kg, screw conveyor diameter: 18 mm, Min. mold height 15mm_Max. platen distance 575 + mm Payment: 100% prior to delivery Manufacturer: Battenfeld Type: BA600-50CDC Condition: überarbeitet Operating hours: 60.790 CLAMPING UNIT: - Clamping force: 60 t Öffnungsweg: 425 mm Mould installation height min.: 350 mm Mould installation height max.: - Tie bar distance (h x v): 320 x 320 mm Plate dimension (h x v): 490 x 490 mm Centering (fix- movingplate): 125 / 125 mm Kedpfxsh Tk Rvo Akljna INJECTION UNIT: IU50 Screw diameter: 18 mm Injection weight in polystyrol: 20,4 g Stroke volume: 22,4 cm³ Einspritzdruck: 2.224 bar CONTROL: Unilog 4B Screen language: DE Operating manuel: DE EQUIPMENT: - Core pulls: ! Air valves: - Hot runner control devices: - Robot interface: Euromap 12 GENERAL DATA: - Installed heating capacity: 3,6 kW Pump drive power: 11,0 kW Total installed power: Motor + Heizung Total weight: 3.350 kg Total size L x B x H: 4,0 x 1,5 x 2,1 m

Condition: used, Year of construction: 2005, operating hours: 81,700 h, clamping force: 45 kN, displacement volume: 69 cm³, injection pressure: 2,400 bar, overall weight: 3,300 kg, screw conveyor diameter: 25 mm, terms of delivery: EXW (ex Works) delivery time: on request terms of payment: % prior to delivery Manufacturer: Engel Type: VICTORY 200/45 Tech + er/usp Condition: aus laufender Produktion Operating hours: ca. 81.700 CLAMPING UNIT: - Clamping force: 45 t Öffnungsweg: 355 mm Mould installation height min.: 175 mm Mould installation height max.: - Tie bar distance (h x v): holmlos Plate dimension (h x v): 550 x 430 mm Centering (fix- movingplate): / mm INJECTION UNIT: IU200 Screw diameter: 25 mm Injection weight in polystyrol: 63 g Stroke volume: 69 cm³ Einspritzdruck: 2.400 bar CONTROL: CC Screen language: DE Operating manuel: DE EQUIPMENT: - Core pulls: 1 Air valves: - Knodpferbqtnjx Aklea Hot runner control devices: - Robot interface: Angußpicker er/usp Other equipment: Nadelverschl. Hydr., Schnittstelle Dosier- und Temperiergerät GENERAL DATA: - Installed heating capacity: 6,8 kW Pump drive power: 11 kW Total installed power: Motor + Heizung Total weight: 3.300 kg Total size L x B x H: 3,3 x 1,2 x 2,2 m

Condition: used, Year of construction: 2001, operating hours: 70,000 h, clamping force: 50 kN, displacement volume: 739 cm³, injection pressure: 2,470 bar, overall weight: 2,500 kg, screw conveyor diameter: 28 mm, terms of delivery: FCA Pegnitz delivery time: on request terms of payment: 100% prior to delivery Knjdpezt Alysfx Aklea

Condition: used, Year of construction: 2009, machine/vehicle number: SO144, Technical Specifications & Performance DataThe SIPA SFR 8 is a rotary PET stretch blow molding machine designed to form PET bottles from preforms for beverage production and industrial packaging applications. Manufactured in 2009, this machine provides a stated production capacity of 12,400 bottles per hour. Its rotary architecture supports continuous bottle production and is suitable for integration into a used bottling line where consistent container supply is required ahead of filling, capping, labeling and secondary packaging equipment.Manufacturer: SIPAModel: SFR 8Year of manufacture: 2009Production capacity: 12,400 bottles per hourBlow mold configuration: 4 mold sets with 8 cavities eachPreform neck finish: 28mm / 1881 short neckSupported bottle formats: 0.5L, 0.75L and 1.5LContainer material: PETAdvanced Automation & Control SystemsThis rotary stretch blow molder is intended for automated PET bottle manufacturing, transforming heated preforms into finished containers through the stretch-blow molding cycle. The supplied preform feeding system supports controlled preform handling into the machine. Rotary blow molding equipment is typically operated through coordinated process controls that synchronize preform transfer, heating, stretching and blowing stages.The machine is supplied with its preform feeding system and chiller. These components support a more complete blowing package by providing preform infeed capability and process cooling. The high-pressure compressor is excluded, so compressed-air infrastructure must be planned as part of installation and commissioning.Production Line Integration CapabilitiesThe SIPA SFR 8 can operate as the bottle production stage of a PET used bottling line. It is positioned upstream of filling monoblocks, labeling machines, shrink wrappers, handle applicators and palletizing systems, producing PET containers for onward handling in a beverage production line. The available mold sets provide flexibility for 0.5L, 0.75L and 1.5L bottle formats, subject to the installed mold and associated line setup.The supplied preform feeding system supports integration with preform handling equipment. A preform hopper is not included, allowing the buyer to configure a hopper solution according to site layout, autonomy requirements and preform logistics. The 28mm / 1881 short-neck finish should be matched with compatible preforms, closures and downstream filling equipment.Machine Condition & Maintenance HistoryThe machine is described as being in very good condition and regularly maintained by the manufacturer. It remains operational until September 30, 2026, indicating that it is currently in production rather than stored or decommissioned. This operating status gives prospective buyers the opportunity to evaluate the machine as part of an active production environment before dismantling.Planned dismantling and loading will follow the end of operation. Buyers should arrange site assessment, technical verification and transport planning in coordination with the removal schedule.Operational Performance & VersatilityDesigned specifically for PET bottle manufacture, the S... Knodsztwmfspfx Aklea

Condition: ready for operation (used), Year of construction: 2005, operating hours: 76,988 h, clamping force: 800 kN, screw diameter: 30 mm, total length: 4,050 mm, total width: 1,930 mm, total height: 2,200 mm, overall weight: 5,200 kg, warehouse no.: 503561 manufacturer: ENGEL type: VICTORY 200-80 Tech controller: CC100 year of construction: 2005 operation hours: 76988 h clamping force: 800 kN size of mould plates h x v: 670 x 600 mm min. mould height: 250 mm max. open daylight: 700 mm opening stroke: 450 mm screw diameter: 30 mm swept volume: 99 ccm injection pressure: 1450 bar Knsdpfx Aozt Sdfeklsa equipment included screen text german CEE-socket 16A core pulling hydraulically 1x machine incl. belt conveyor machine incl. Handling machine incl. water flow regulator machine without material hopper Anti vibration mounts Schuko-socket 10A measures of machine l x w x h: 4.05m x 1.93m x 2.2m total weight: 5200KG technical data robot-system handling type: Linearhandling manufacture: Engel controller: ER-HLI 31 VC year of construction: 2005 handling weight: 2 kg screen-text: deutsch total weight: 250 kg

Condition: used, Year of construction: 2012, operating hours: 55,400 h, clamping force: 100 kN, displacement volume: 201 cm³, injection pressure: 2,000 bar, overall weight: 5,400 kg, screw conveyor diameter: 40 mm, terms of delivery: EXW (ex Works) delivery time: on request Knedpfx Aoylpy Aeklja terms of payment: 100% prior to delivery

Condition: used, Year of construction: 2012, operating hours: 55,800 h, clamping force: 100 kN, displacement volume: 201 cm³, injection pressure: 2,000 bar, overall weight: 5,400 kg, screw conveyor diameter: 40 mm, terms of delivery: EXW (ex Works) delivery time: on request terms of payment: 100% prior to delivery Ksdpfx Ajylpyvjklena

Condition: used, Year of construction: 2020, operating hours: 5,400 h, clamping force: 400 kN, displacement volume: 475 cm³, injection pressure: 1,650 bar, overall weight: 24,500 kg, screw conveyor diameter: 55 mm, Freight basis: ex-site Ksdev S H Rhepfx Aklena Delivery time: by arrangement Payment terms: 100% before taking delivery of the machine, net

Condition: used, Year of construction: 2020, operating hours: 1,600 h, clamping force: 400 kN, displacement volume: 475 cm³, injection pressure: 1,650 bar, overall weight: 24,500 kg, screw conveyor diameter: 55 mm, terms of delivery: EXW (ex Works) Kodpfxjv S H Rbo Akljna delivery time: on request terms of payment: 100% prior to delivery

Condition: used, Year of construction: 2020, operating hours: 4,200 h, clamping force: 90 kN, displacement volume: 113 cm³, injection pressure: 2,400 bar, overall weight: 7,500 kg, screw conveyor diameter: 30 mm, terms of delivery: EXW (ex Works) delivery time: on request terms of payment: 100% prior to delivery Knedpfxov S H N Rj Aklja

Condition: used, Year of construction: 2013, operating hours: 29,000 h, clamping force: 50 kN, displacement volume: 59 cm³, injection pressure: 2,500 bar, overall weight: 3,700 kg, screw conveyor diameter: 25 mm, terms of delivery: EXW (ex Works) delivery time: on request terms of payment: 100% prior to delivery Manufacturer: Krauss Maffei Type: KM50-180AX Condition: aus laufender Produktion Operating hours: ca. 26.000 CLAMPING UNIT: - Clamping force: 50 t Öffnungsweg: 300 mm Mould installation height min.: 150 mm Mould installation height max.: 470 mm Tie bar distance (h x v): 410 x 360 mm Plate dimension (h x v): 510 x 460 mm Centering (fix- movingplate): 125 mm INJECTION UNIT: IU180 Screw diameter: 25 mm Injection weight in polystyrol: 54 g Stroke volume: 59 cm³ Einspritzdruck: 2.500 bar CONTROL: MC5 Screen language: DE Operating manuel: DE EQUIPMENT: - Core pulls: 2 x (Hydr. Kernzug-Aggregat) Air valves: 2 Hot runner control devices: 6 Robot interface: Euromap 67 Other equipment: Qualitätsüberwachungspacket GENERAL DATA: - Installed heating capacity: 8,1 kW Pump drive power: entfällt Total installed power: Motor + Heizung Total weight: 3.700 kg Total size L x B x H: 4,4 x 1,6 x 1,9 m Kedjppigdepfx Aklena

Condition: used, Year of construction: 2007, operating hours: 67,000 h, clamping force: 250 kN, displacement volume: 530 cm³, injection pressure: 2,426 bar, overall weight: 14,200 kg, screw conveyor diameter: 50 mm, Freight base: FCA Pegnitz Delivery time: by arrangement Payment terms: 100% before takeover of the machine, net Knedpfewlkcaex Aklsa

Year of construction: 2004, condition: used, A BATTENFELD large-format horizontal injection molding machine in need of repair is offered. Operating pressure: 210bar, clamping force: 4500kN, screw diameter: 85mm, injection volume: 2128cm³, injection pressure: 1624bar, tie-bar spacing X/Y: 900mm/800mm, opening stroke: 950mm, max. mold height: 970mm, oil capacity: 900l, connected load: 55kW, operating hours: approx. 82510h, weight: approx. 20.4t. The servo motor for the screw drive is defective. In addition, some smaller parts are missing. An on-site inspection is possible. Ksdpfxjzvy E Ao Aklona

Condition: used, Year of construction: 2012, machine/vehicle number: SO141, Used MORETTO EPL 5-8 N blow molding machine - Year 2012Technical Specifications & Performance DataThis extrusion blow molding machine is engineered for producing hollow plastic containers with high repeatability and efficiency. Manufactured by Magic with a full-electric drive concept, it is equipped for industrial packaging and beverage production environments where precision, uptime, and energy efficiency are critical. It suits used bottling line upgrades and second hand equipment integrations requiring robust blow molding capabilities.Blow molding process: Extrusion blow molding, full electricMaximum blown container volume: 8000 cm³Clamping force: 100 kNSpeed: around 200 Unit/hour for ( Distilled water container ) Dry cycle time: 2.2 sOpening stroke: 250 mmMaximum mold dimensions (L × P × A): 425 / 2x130 / 400 mmGeneral electrical power: 15 kWTotal installed electrical power: 64 kWExtruder screw diameter: 70 mmExtruder L/D: 24 L/DExtruder motor power: 35 kWExtruder heating zones: 5Extruder heating power: 10.6 kWSingle extrusion head max die diameter: 100 mmHead heating zones: 4Head heating power: 3.8 kWMachine footprint (W × L × H): 1900 × 5050 × 3250 mmTotal system weight: 7000 kgNoise level: 75 dB(A)Advanced Automation & Control SystemsThe full-electric architecture enhances precision and repeatability while minimizing energy consumption and maintenance compared to hydraulic systems. Fast dry-cycle performance supports higher throughput and stable cycle times. Temperature control across multiple heating zones on the extruder and head ensures consistent parison quality and stable process control for demanding industrial packaging applications.Full-electric drive for efficient, clean operationMulti-zone temperature management on extruder and die headStable, repeatable dry cycle for consistent productionOperator-friendly adjustments and setup for mold changesProcess reliability suitable for stringent quality requirementsProduction Line Integration CapabilitiesThis machine integrates smoothly within a used bottling line or a mixed-manufacturer production environment. It comes with a comprehensive set of auxiliaries to streamline upstream and downstream handling, supporting end-to-end beverage production or industrial packaging workflows.Included auxiliaries: hopper feeders, suction unit, dryer, granulator, cooler, color mixer, conveyorsAuxiliaries brand: Moretto (most components purchased new in 2012)Inline or standalone operation for flexible layoutsSupports diverse container geometries enabled by robust clamping and mold size window... Knedezrgqkepfx Akloa

Condition: used, Year of construction: 2000, machine/vehicle number: SO142, Used MAGIC MOD. MGL5 blow molding machineTechnical Specifications & Performance DataThis extrusion blow molding machine is engineered for producing hollow plastic containers with consistent quality and reliability. Configured with a single carriage and single head, it is tailored for medium-format containers up to 5.0 liters, offering robust performance for industrial packaging applications. The machine has undergone a major overhaul and is in perfect working order, both mechanically and electronically.Maximum container volume: 5.0 LMachine type: Extrusion blow molding, single carriage, single headClamping force: 83 kNHydraulic working pressure: 160 barBlow nozzle pressure: 0–70 barExtruder screw diameter: 70 mmExtruder motor power: 29 kWExtruder heating power: 10.6 kWHead heating power (single head): 3.4 kWMaximum die diameter (single head): 120 mmMold opening stroke: 210 mmMaximum mold dimensions (W – Thickness – H): 400 / 2×110 / 400 mmHydraulic pump/Power unit motor: 18.5 kWInstalled power (total): 62 kWAverage electrical consumption: 40 kWBlowing air pressure: 6–8 barAir consumption: 800 Nl/minCooling water pressure: 2–3 barCooling capacity (water): 30,000 Kcal/hHydraulic oil tank capacity: 270 LMachine footprint (W × L × H): 2200 × 4250 × 2900 mmComplete system weight: 7000 kgModel code: MGL5Advanced Automation & Control SystemsThe machine is equipped with a new Gefran PLC, delivering updated electronic control and a modernized program to ensure repeatable cycles, reliable temperature regulation, and stable extrusion. Multi-zone temperature management covers the extruder and head heating, providing precise control over melt conditions and wall thickness quality. Operator-friendly diagnostics support fast setup and streamlined troubleshooting, while integrated interlocks and status monitoring promote safe, efficient operation. The control architecture supports consistent processing of HDPE with accurate setpoint management, alarms, and real-time process visibility.Production Line Integration CapabilitiesDesigned for straightforward integration into industrial packaging and used bottling line environments, the machine features a part discharge belt conveyor for clean outfeed handling. It can be paired with downstream trimming, leak testing, visual inspection, and packing systems to create a complete second hand production cell. Format compatibility focuses on containers up to 5.0 liters, with a structure well-suited for HDPE bottles, jerrycans, and similar industrial packaging formats.Machine Condition & Maintenance HistoryThe unit is reported in excellent condition and fully oper... Knjdpfx Akezrgp Tjlea

Condition: new, Year of construction: 2005, Planing machine with infeed device EM 11 Ksdpfx Akozvvuajljna with 5th spindle at the bottom Includes 5 planing heads.

Condition: excellent (used), Year of construction: 2014, operating hours: 56,851 h, functionality: fully functional, clamping force: 1,100 kN, screw diameter: 25 mm, displacement volume: 86 cm³, injection pressure: 3,000 bar, mold height (min.): 200 mm, opening stroke: 450 mm, overall weight: 4,800 kg, input voltage: 400 V, Equipment: documentation/manual, warehouse no.: 503665 manufacturer: Wittmann Battenfeld type: EcoPower 110-350 controller: UNILOG B6P year of construction: 2014 operation hours: 56851 h clamping force: 1100 kN Ksdpfjy Akn Rjx Aklsna distance between tie-bars h x v: 470 x 420 mm size of mould plates h x v: 680 x 663 mm min. mould height: 200 mm max. mould height: 450 mm max. open daylight: 830 mm opening stroke: 380 mm screw diameter: 25 mm swept volume: 86 ccm injection pressure: 3000 bar equipment included screen text german Screentext Multi-Language CEE-socket 16A machine incl. water flow regulator Anti vibration mounts measures of machine l x w x h: 4.57m x 1.5m x 2.13m total weight: 4800KG