Used Cloos Robot for sale (49)

Condition: used, Year of construction: 2023, 2023 Cloos Robot Welding Cell With QRC-300 Robot & Qineo Next 452 Premium MIG/MAG Welding Source - With Leuze Electronic MLS Safety Light Curtains, Welding Torch Cleaner & Pendant Controls. Dual Rotary Transfer Table dimension 650 x 450mm. Cloos QRC-300 Robot- Swivelling Range Axis 1 -170 ° / +170 °, Axis 2 -90 ° / +125 °, Axis 3 -220 ° / +70 °, Axis 4 -170 ° / +170 °, Axis 5 -135 ° / -135 °, Axis 6 -300 ° / +300 °, Swivelling Speed Axis 1 200 °/sec, Axis 2 200 °/sec. Axis 3 230 °/sec, Axis 4 490 °/sec, Axis 5 540 °/sec, Axis 6 520 °/sec. Working Area Ø3,000mm. Range 2,000mm. Pay Load 8kg. Repeatability +/-0.1mm. Floor Space 400 x 400mm. Weight 110kg. S/No. 0881590000-20040 (2023). Qineo Next 452 Premium- Welding Current 25A/15V-450A/36.5V. Welding Current At 60% Duty Cycle* 450A/36.5V. Welding Current At 100% Duty Cycle* 350A/31.5V. Open Circuit Voltage 80V. Mains Voltage 380V-480V/3 Phases. Connection Cable 4 x 6mm2. Mains Fuse Slow-Acting 32 A. Type Of Protection IP. Insulation Class F. Type Of Cooling F. Dimensions L720 x W340 x H500mm. Weight Of Power Unit 63kg. Weight Of Cooling Module 28kg. S/No. Qinx 1963 (2023). Wire Drive Units QINEO NexT-Wire Feed 30m/min, Wire Ø0.8-2mm. Overall Dimensions W350 x D270 x H230mm. Weight 10.2kg. Godpfx Aeyx Hzxjnxoub

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, machine/vehicle number: 306 431, type of input current: three-phase, total height: 2,165 mm, total width: 1,800 mm, total length: 3,000 mm, overall weight: 1,250 kg, input voltage: 400 V, type of cooling: air, Equipment: cabin, Machine year of manufacture 2021, purchased used in December 2022. Inspected, repaired, and adjusted by a specialist company in April 2023. Since then, it has only operated for a few hours in test run mode. Gusdpfjy Ndcbex Anxjb

Condition: not inspected (used), Manufacturer: Cloos Tip: Romat 56 Gujdjvxqy Topfx Anxjb The device has not been tested and its condition is unknown. Sold with the accessories shown.

Condition: not inspected (used), Manufacturer: Cloos Type: Romat 76 S The device has not been tested and its condition is unknown. Godpsvxqzqsfx Anxeub Sold with the accessories shown.

Condition: used, Year of construction: 2007, table diameter 4520 mm table load 35000 kg swivelling range 110 Grad total power requirement 44 kW weight of the machine ca. / t required space / m Type: ROMAT 350 / LVEB-120000N-4m / VVEs-D-18000N-5m-S / QVEB-2m travelling beam / CR-200000N / Hydraulic scissor lift table In the scope of delivery: Item Designation 1 Welding power source GLC 603 Quinto SD 2 Wire drum Gjdpfxjrmulvs Anxsub 3 Service door 2.1 4 Robot control cabinet 5 Service door 1.2 6 Scissor lift table (shown in parking position) 7 Cross-travelling unit QVEB 8 ROMAT 350 robot 9 Service door 1.1 10 Safety fence 11 Platform 12 Positioner 13 Sliding door 1 14 Linear traversing unit LVEB 15 Vertical traversing unit VVEs 16 Sliding door 2 The disc ring on the table is a device that is not included in the scope of delivery ----- Technical data - Mechanical dimensions (without control unit and superstructures): approx.6440(57 7 0)x4520(2700)x5460(3320) LxWxH - Turntable diameter: 4520mm - Weight: approx. 25,000kg (without superstructure) - Speed range: 0.004 - 1.07 rpm - Welding current coupling: 600 A - Maximum table load capacity: 35 tons (according to load chart) Ambient temperature Storage / transport 0 to 60'C Operation +4 to 35 "C Interfaces Central transfer point for control, power supply, earth connection ----- 2.3 Linear traversing unit, LVEB Type LVEB-120000N 4m Dimensions W x D x H 7,700 x 2,440 x 776 mm Weight 4,355 kg Travelling distance 4,000 mm Load of the carriage 120,000 N Drive unit Gear motor Precision bevel gear motor Manufacturer Stöber Type K402VF0250EK703V Power 4.21 kW Voltage UKE 140 V / 1000 rpm Current Rated current IN: 8.32 A Type of current Standstill current I0: 9.04 A Motor speed 3,000 rpm Gear ratio i = 25.28 ----- 2.4 Vertical traversing unit, VVEs Type VVEs-5m Dimensions W x D x H 2,000 x 1,960 x 7,150 mm Weight 9,500 kg Travelling distance 5,000 mm Max. moving mass 18,000 N Drive unit Gear motor Bevel gear motor with brake Manufacturer Stöber Type K713VF0790MQ30ED704B Power 4.8 kW Motor speed 2,000 rpm Gear ratio i = 78.83 (20181/256) ----- 2.5 Cross-travelling unit, QVEB Type QVEB-2m Dimensions W x D x H 1,270 x 4,100 x 756 mm Weight 1,950 kg Travelling distance 2,000 mm Load on the travelling beam 10,000 N Max. moving mass 18,000 N Drive unit Gear motor Precision flat geared motor Manufacturer Stöber Type FS202VQ0145ED402U Power 1.43 kW Voltage UKE 140 V / 1000 rpm Rated current IN 2.86 A Type of current Standstill current I0: 3.1 A Motor speed 3,000 rpm Gear ratio i = 14.65 (3180/217) ----- 2.6 Rotary indexing table Type CR-200kN Manufacturer Cloos Dimensions W x D x H 1,820 x 2,120 x 541 mm Weight 2,850 kg Drive unit Gear motor Bevel gear motor Manufacturer Stöber Type K814VG1540EK803U Power 6.7 kW Motor speed 3,000 rpm Gear ratio i = 154.322 ----- 2.7 Robot ROMAT 350 Type ROMAT 350 Dimensions (W x D x H) in reference position 1,900 x 600 x 1,500 mm Weight 205 kg Footprint 500 x 515 mm N...

Condition: excellent (used), Year of construction: 2020, CLOOS QIROX Robotic Welding Line – Dual Gantry System – 2020 General Description For sale: high-performance robotic welding line based on the renowned CLOOS QIROX system, designed for automated welding of medium to large steel structures. The system consists of two gantry-mounted welding robots working on a shared linear axis, combined with rotary positioners, allowing efficient welding of long components and complex assemblies. This is a modern (2020), industrial-grade solution suitable for heavy fabrication, steel structures, frames, and serial production. Key Equipment & Configuration Robots • Model: CLOOS QIROX QRC 410 • Year: 2020 • Type: 6-axis articulated robot • Payload: 10 kg (wrist capacity) • Repeatability: ±0.1 mm • Working range: approx. Ø 5000 mm • Welding processes: MIG/MAG, TIG, optional cutting & sensor integration ✔ High dynamics and precision Godpfxjyvaahj Anxjub ✔ Modular design for flexible applications ✔ Suitable for complex welding paths and long seams Controllers • Model: QIROX Controller QC2.02 / QRC 410 • Industrial PC-based control system • Simultaneous control of robot + external axes • Power supply: 3x 400V / 32A 3x 400V / 19A • Frequency: 50/60 Hz • Power: up to 21.5 kVA ✔ Robust cabinet design ✔ Optimized human-machine interface ✔ High path accuracy and process stability Positioners (Rotary Tables) • Model: CLOOS QR-CTU-100-09 2.0 • Load capacity: 10,000 N (≈1,000 kg) – vertical position 20,000 N (≈2,000 kg) – horizontal position • Torque: up to 1600 Nm • Tilting moment: 8800 Nm • Drive power: 4.5 kW ✔ Programmable axes synchronized with robot ✔ Ideal for complex geometries ✔ Enables optimal welding position and accessibility System Layout • Dual gantry system (2 robots on linear track) • Long working area for large structures • Integrated working tables for long parts • Suitable for: – frames – steel constructions – long welded assemblies Typical advantages of this configuration: • Extended working range via linear axis • Possibility of simultaneous welding operations • High productivity and reduced cycle time Advantages ✔ High productivity and repeatability ✔ Excellent weld quality ✔ Flexible configuration (different parts & sizes) ✔ Proven CLOOS industrial reliability ✔ Suitable for serial and custom production Typical Applications • Steel structures • Machine frames • Automotive components • Construction elements • Heavy fabrication Technical Highlights (Summary) • Robots: 2x QIROX QRC 410 • Axes: 6-axis robots + external axes • Control: QIROX QC2.02 • Positioners: up to 2,000 kg capacity • Power: 400V / 50–60 Hz • Year: 2020 • System type: gantry welding line Condition & Availability • Condition: Very good, fully operational • Available for inspection under power • Can be dismantled and shipped worldwide

Condition: excellent (used), Year of construction: 2004, Carl Cloos GLC 503 Quinto SD welding machine. A total of 4 units available. Year of manufacture: 2004-2004-1999. Price refers to 1 unit. Godpetkuk Rofx Anxoub

Year of construction: 2011, condition: excellent (used), Cloos welding robot Qirox QRC 320 incl. control V 6, pedestal for standing arrangement, Gedjizwv Nspfx Anxeub Cloos welding machine Quinto II 603 ( 600 A), wire feed, welding torch, torch hose package, mech. cleaning, pressure booster 1 rotary tilt table WPK 5000, pick-up weight 500 kg, 1 start preselection, 1 control for customer-provided sliding door gas nozzle sensor, arc seam search, point editor Unit will be completely overhauled and serviced before delivery. Second station with another, same rotary tilt table possible.

Condition: ready for operation (used), Year of construction: 2013, This CLOOS QRH 390 was manufactured in 2013. It features a QRH 390 with a QIROX Controller V6 and a C-stand MH=24330. Equipped with advanced welding technology and an extraction system, this welding robot is ideal for enhancing your production capabilities. Contact us for more information about this machine. Gedpjx S Siusfx Anxoub

Condition: refurbished (used), functionality: fully functional, input voltage: 400 V, ground cable length: 3,000 mm, warranty duration: 3 months, type of cooling: water, hose package length: 1,000 mm, welding current (min.): 60 A, welding current (max.): 450 A, Equipment: type plate available, Carl Cloos GLC 451 C - Water-cooled Mig Mag Step-controlled Specifications: 60-450 AMP 380 Volt Gusdey Rqt Aepfx Anxob Water-cooled 30 steps adjustable 2/4 stroke 4 roller driven Adjustable burnback time Includes: Mig welding torch, earth cable with clamp, gas hose, and 10 metre intermediate package. Visits by appointment only. Test welding is possible. A video of the machine in welding condition is possible. We also deliver to countries like Spain, Germany, Austria, Lithuania, Greece and all other countries inside and outside Europe with Euro pallets per freight. All our machines have been serviced and are 100% ready to use unless otherwise indicated. The pictures above show the real machine. We can also offer you other types of machines such as: Used, New, Mig, Mag, Co2, Tig, Pulse, AC/DC, Plasma, Water-cooled, Electrode, Brands we offer: OTC, Migatronic, Lincoln, Miller, Fronius, Kemppi, Parweld, Tico, Lorch, Rehm, Selco, Carl Cloos, Cebora, Esab, Saf, EWM, Ess, Kemper. You always do business with Cjays Lastechniek itself and never with third parties.

Condition: used, Year of construction: 2015, 2015 Cloos GLW 270 CNC Welder and Plasma Cutter with Robot Gjdpfx Asy Dr Ihonxjub CNC Control: Qirox C QRC 350, Welding source: Cloos Qineo Pulse 450, TIG Welding source: Cloos GLW 270, Plasma: Hypertherm HPR260XD, Basic parameters: diameter of processed ends from 500 to 5000 mm, end weight up to 5000 kg, diameter of processed pipes up to 1000 mm, length of processed pipes up to 3000 mm, pipe weight up to 500 kg, maximum cutting current of the plasma generator 230 A, maximum TIG welding current 270 A, maximum MAG welding current 450 A, Robotic station functionality: plasma cutting and chamfering of holes in bottoms with diameters ranging from 500 to 5000 mm, plasma cutting and chamfering of holes in shells with diameters ranging from 500 to 5000 mm (shell axis vertical), including at an angle to the vertical axis of the bottom, plasma cutting and chamfering of nozzles with a diameter of up to 1000 mm, welding of nozzles in bottoms with guaranteed penetration layers. The condition for obtaining proper penetration welds is proper preparation and assembly of the part – e.g., lack of end ovality (faulty material), even gap (incorrect assembly), etc. In the case of densely packed nozzles in the bottom, welds may be impossible due to lack of access with the welding torch. - welding of nozzles in shells, welding of tubes in tube sheets with diameters ranging from 500 to 5000 mm. The tubes in the tube sheets should be repeatedly secured and expanded. When welding tubes in tube sheets with diameters greater than 3000 mm, it will be necessary to rotate the tank several times. TIG process, MAG process, Maximum bottom thickness: 20 mm, Maximum jacket thickness: 12 mm, Station equipped with a filtration system, Station equipped with an automatic torch change system, Station equipped with a system enabling automatic joint position recognition, Station equipped with a vision system enabling process monitoring on a separate monitor with the option of connecting a plant recorder, Welding parameter recording and reading system, Manifold with a solenoid valve for shielding gas in the rotary table, Self-centering chuck in the 500-5000 range for the rotary table, Self-centering chuck for a vertical rotary table up to Ø600, S/No: 163 (2015)

Condition: used, Year of construction: 2002, Equipment: documentation/manual, Technical data in the attachment. Robot including workpiece positioner and welding technology. Gjdpsy Emz Sefx Anxsub

Condition: used, MIG MAG welding machine, shielding gas welder CLOOS type GLC 357 N MIG MAG welding power source Serial no. 576 Year of manufacture approx. 1985 Rated output 350 Amp. Output 350 Amp. - 80% duty cycle 310 Amp. - 100% duty cycle Continuously adjustable output range Connection hose package: 4.5 meters Power supply: 380 Volt, 50 Hz, 32 Amp plug - 2-stroke and 4-stroke welding function - External wire feeder type CK 72 ZK with 2-roller drive and 4.5 meter hose package Gusdpfxohubg Te Anxob - 3 meter hose package with central connection and CLOOS hand torch - Water-cooled - Pressure gauge for gas cylinder - Welding unit equipped with 1 mm welding wire Space requirements (L x W x H): 1250 x 600 x 1100 mm Weight: 260 kg Machine tested – fully functional

Condition: ready for operation (used), Year of construction: 2016, number of axes: 6, This 6-axis CLOOS QRC 350 QIROX welding robot was manufactured in 2016. It features a maximum load capacity of 15 kg, a workstation reach of 3400 mm, and advanced V6 control. Equipped with a 450A Qineo Pulse A welding machine, it ensures precise and efficient welding. The robot includes a touch sensor and an arc sensor for enhanced accuracy during operations. Consider the opportunity to buy this CLOOS QRC 350 QIROX welding robot. Contact us for more information about this machine. Additional equipment • Premium control panel with wall bracket and cable holder Gjdpfx Ajyaliienxoub • External gas cleaning device • Adjustable electro-pneumatic valve • Wire feed equipment Machine Benefits Technical Machine Benefits • Built-in welding interface and software • Protective tube for wire transfer • High usability with movable counter-side support • Workstation: 3400 mm • Longitudinal track travel speed: 1. 8 m/sec • Longitudinal track travel length: 7000 mm • Qineo touch sensor: 60 v • Arc sensor for welding path adjustment Extra Information Includes standard height robot stool and computer connector for enhanced usability. Control Unit Control: V6 Advanced Digital inputs and outputs: 16 USB connectors: 2 Connectivity: Expandable up to 16 axes, CAN-Bus, serial interfaces

Condition: ready for operation (used), Year of construction: 2023, This CLOOS Instant pro IRPS was manufactured in 2023. It features a QIROX welding robot with a maximum payload of 10 kg and a working range of Ø 3900 mm. Equipped with advanced QC 2 control system, it includes a programming handheld device and supports new tandem leading/trailing processes. Ideal for high-quality welding applications, it also comes with a comprehensive set of welding and sensor technologies. Contact us for more information about this machine. Machine Benefits Technical Machine Benefits • Working range: Ø 3900 mm • Programming handheld device with touchscreen • Qirox technology interface • Tool controller ctms • Tcp measuring device Extra Information Welding Technology Power source Arc sensor Water cooling module Control module Wire drive unit Robot welding torch Software Parameter grinding Distance-dependent transition between parameter lists Multi-layer technology Programmable pendulum figures Software language: German IRPS Scanner Control IPC Rittal control cabinet Touch screen Guedpfx Ajyaimlsnxeb Scanner interface Uninterruptible power supply Scan width: 1000 mm at 500 mm product height Scan speed: 300 to 1000 mm/sec Burner Cleaning Unit Torch cleaning device Compressed air amplifier Wire cutter Control Unit Digital inputs/outputs: 16 Serial interface Computer connection: QIROX controller CAN bus USB interfaces: 2 Flash memory: 8 GB Buffer module: 24V Point editor Expandable to up to 16 axes

Condition: ready for operation (used), Year of construction: 2019, This CLOOS QIROX QRC 350-E was manufactured in 2019. It features a maximum payload of 15 kg and a working range up to 4500 mm. Equipped with a QC 2 Master control system, it includes a handheld programming device with an 8.4" touchscreen. The robot supports expansion up to 12 axes and comes with integrated welding software and a digital interface. Consider the opportunity to buy this CLOOS QIROX QRC 350-E welding robot. Contact us for more information about this machine. Extra Information Robotics and Control Unit Max. payload: 15 kg Working range: 0–4500 mm Digital inputs/outputs: 16 Serial interface: Yes CAN bus: Yes USB interfaces: 2 Flash memory: 8 GB Buffer module: 24 V Expandable to up to 12 axes Welding Technology Power source: Included Welding interface: Integrated Welding and function test: Included Torch cleaning: CMR-8-C torch cleaning device, upright Robotic welding torch: Included Sensors Tactile sensor: Yes Arc sensor: Included Technical Data of Workpiece Positioner Load capacity: 10 kN Nominal torque: max. 1600 Nm Tilting moment: max. 8800 Nm Mass moment of inertia: 900 kgm² Rotation range: +,- 360° Swivel range: 370° Welding Fume Extraction Extraction capacity: 3000 - 4320 m³/h Motor power: 5.5 kW Connection voltage: 3 x 400V/50 Hz Noise level: 65 dB(A) Gjdpfjx D Hdhox Anxoub Weight: 640 kg Dimensions (W x D x H): 1413 x 1413 x 2110 mm

Year of construction: 2020, condition: ready for operation (used), total height: 3,200 mm, number of axes: 6, This 6-axis CLOOS QIROX QRC-350-E was manufactured in 2020. It features a maximum reach of 1550 mm and a payload capacity of 6 kN, making it suitable for various robotic welding applications. The system includes a welding positioner and a laser system for enhanced functionality. If you are looking to get high-quality robotic welding capabilities, consider the CLOOS QIROX QRC-350-E automation system we have for sale. Contact us for further details. • Controller: QIROX Controller QC2 M • Payload: 6 kN • Maximum reach (MR): 1550 mm • Application: Robotic welding • System type: Complete robotic welding cell Additional equipment Guedpfjymdnqox Anxob • Welding positioner: QR-WP-DH-TC 5 / 7.5 kN • Laser system: iCSE LD

Condition: excellent (used), Year of construction: 2012, CLOOS GLC 403 Quinto welding machine. A total of nine Cloos 403 machines are available. Year of manufacture: from 2005 to 2012. Other models of the Cloos 503 welding machines are in stock Gusdpfx Astkunujnxsb

Condition: excellent (used), Year of construction: 2003, Cloos GLC 451 C welding machine. Year of construction: 2003 With welding package Gusdpfx Aetkurisnxob

Condition: used, Year of construction: 1997, functionality: fully functional, System consisting of: Welding robot Romat 310, ROTROL 32 TM controller and programming handset with cable, connecting cable for robot control cabinet Pedestal for robot Tactile sensor, arc seam tracking Drive for Micro SD card for program backup incl. 2 cards Quinto 503 welding machine, wire feeder Welding torch MRW 380, torch hose package Duo drive wire feed unit, torch testing gauge 15 kg wire spool holder, drum equipment Mechanical cleaning, pressure booster 2-station rotary table 4 DP 2200 (load capacity 220 kg per station) 5 m connecting cable to control cabinet 1 light barrier 1 pre-selection start Wiring diagrams Documentation, functional warranty Gjdpfjyh Hl Sjx Anxoub Delivery date: immediately available

Condition: used, Year of construction: 1999, welding power 40 - 350 / 12 - 40 A/V open-circuit voltage max. 56 V welding current 100%: 300 A wire speed 0 - 24 m/min capacity 15,9 kVA voltage 3 ~ 400 V frequency 50 Hz Coolant: F Protection class IP 23 weight of the machine ca. 153 + 22 kg dimensions of the machine ca. 1,10 x 0,60 x 1,15 m Welding machine Guodoymp Sbepfx Anxob CLOOS - GLC 353 MC 3 - incl. Wire drive Unit CLOOS - CK98 A

Condition: used, Plasma cutter CLOOS type CPS 40/80 Year of manufacture 1990 Power at 60 % ED 80 Amp. Power at 100 % ED 40 Amp. Adjustment range 40 and 80 Amp (2 steps) cutting capacity with steel max. 25 mm Hose package length 5.5 meters Mains connection 400 Volt with 32 Amp. Plug - Hand torch CLOOS dimension L x W x H 700 x 600 x 750 mm weight 160 kg Gusdpfx Aodzqccenxsb good condition

Condition: good (used), functionality: fully functional, load capacity: 500 kg, Welding turntable, L-manipulator, positioner, in excellent condition, includes additional clamping plate. Rotating and tilting (overhead), steplessly adjustable speed. Mechanical height adjustment from 800 mm to 1100 mm. Outreach 1000 mm. Overall height 1800 mm. Length 3000 mm. Width 1100 mm. Clamping plate diameter 1000 mm. Gsdpfx Aoylkn Ijnxeub

Condition: new, For sale: Industrial set used in welding applications by CLOOS – a renowned German manufacturer of automation systems. The set includes: Hollow shaft (Hohlwelle kurz für W) • Identification: SA-Nr 455799, part number • Robust, steel construction • Production date: 25.05.2018 • Very good technical condition, stored, minor surface corrosion traces Large mounting bracket/adapter (visible positioning sockets) Guedpfsw Rdyzjx Anxsb • Heavy-duty, solid construction • Designed to work with the shaft – precise positioning/rotation of workpieces • No play, everything holds firmly • Coded mounting and internal passage Ideal set for: • welding positioners • industrial robot arms • adaptation of drives and gearboxes

Condition: refurbished (used), robot mechanic for Exchange. Mechanic overhauled by Cloos. Guodpfxed H T I Eo Anxob Mechanic on stock.