Used Complete Line for sale (21,419)

Condition: used, Year of construction: 1990, Overview This is a complete automatic KEG line for stainless-steel kegs, built in 1990 by Leifeld & Lemke and continuously extended and modernised over its service life. It covers the full cycle from empty-keg infeed and centring through external washing, internal cleaning, filling and full-keg checking to automatic palletising. According to the seller it runs at up to 130 kegs/h in the 30 L format in three-shift duty. Control is by Siemens SIMATIC PLCs of mixed generation (see Condition). Technical data - Manufacturer (line builder): Leifeld & Lemke - Year of manufacture: 1990 (continuously upgraded since) - Machine type: complete automatic KEG cleaning and filling line - Capacity: up to 130 kegs/h at 30 L (seller-stated) - Keg formats: 20 L, 30 L, 50 L, basket fitting (Korbfitting); no slim kegs - Control: Siemens SIMATIC S5 and S7-300 (mixed generations) Scope of Delivery Hodpoz D S Sbjfx Airow - Empty-keg infeed with centring column | Leifeld & Lemke | Detects intermediate layers, centres kegs for the robot | 1990 - Keg handling robot | KUKA | Loads empty kegs onto the conveyor, unloads full kegs onto pallets | approx. 2015 - Fitting tightener | Leifeld & Lemke | Re-torques loose keg fittings | 1990 - Keg inverter | Leifeld & Lemke | Inverts kegs for internal rinsing | 1990 - External keg washer | Leifeld & Lemke | Steam-heated, 2 zones (brushing and high pressure) | 1990 - Internal cleaning | Leifeld & Lemke | Caustic pre-clean (approx. 10 min dwell, for wheat beer) and main cleaner | 1990 - CIP plant | Leifeld & Lemke | 5 tanks with chemical dosing, steam-heated (seller-stated) | 1990 - Keg filling block | KHS Till | 1990 - Full-keg check-weigher | Leifeld & Lemke | With keg blow-off | 1990 - Cap placer | Leifeld & Lemke | Seats plastic caps onto the fitting | 1990 - Palletiser | Albert Frey | Served by the KUKA robot | 1990 - Electrical documentation | Circuit diagrams available as physical copies Not included: handle control, Vision Tec inspection system, labeller. No operating manual is available. Condition Used - still installed and under power, in active three-shift production and reported by the seller to be well maintained. The 1990 line has been progressively modernised: kegs were originally hand-loaded, the robot was later replaced (approx. 2015, seller-stated) and Siemens SIMATIC touch HMIs added. Control mixes Siemens SIMATIC S5 (reportedly filler, CIP and pre-/main cleaning) and S7-300 (the remaining stations, conveyors and washer); as the S5 generation is long discontinued, spare-part supply and future control integration should be planned accordingly. Availability In production until approximately April 2027; the existing and the successor line will then run in parallel, so realistic handover is from around Q2 2027. Location: Germany. Viewings in operation are possible at any time. Dismantling and removal can be arranged on request. Price on request.

Year of construction: 2022, condition: used, - Model: Classic Line 2 FE - Year of manufacture: 2022 - Load capacity: 800 kg - Collection capacity: 205 liters - Dimensions: 1,236 x 815 x 360 mm Hedpfxszrvk Te Airjw - With grating - Steel construction - Color: blue (powder-coated) - Weight: 64 kg

Year of construction: 2022, condition: used, - Model: Classic Line 60 KK - Year of manufacture: 2022 Hsdpszrvkasfx Airow - Load capacity: 400 kg - Collection capacity: 65 liters - Dimensions: 785 x 639 x 281 mm - With grating - Steel construction - Color: blue (powder-coated) - Weight: 37 kg

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, For sale is a complete, fully functional automatic painting line, based on the Superfici Compact Spray 1300 automatic spraying system, along with a CEFLA drying system. The line is complete, currently assembled, and has been used in regular production. It is being sold as a complete technological line. Hedez Ix Azepfx Airjw The set includes: - Superfici Compact Spray 1300 painting machine - CEFLA drying tunnel – total length approx. 13 m - CEFLA control cabinet - CEFLA conveyor - GRACO Merkur X48 pump - GRACO D08B pump Condition: used, complete, and fully functional. The machine can be inspected on-site in Poland, in the Silesian Voivodeship (near Bielsko-Biała). Upon request, a video showing the line in operation and additional technical information are available. Available immediately. The terms for dismantling, loading, and transport can be agreed upon individually. Price: 49,900 EUR net.

Year of construction: 2020, condition: excellent (used), functionality: fully functional, Production batch for the rubber industry. Hodpfoz Ix A Iex Airew

Year of construction: 1988, condition: used, Olma Combi Door Panel Line (1988), Panel Dimension Length Min/Max 330/1320 x 538mm Width, Cycle Time 17 Seconds, Dimension of Sheet Min/Max Length 390/1400mm x 600 Width x 0.5mm Thickness Location: These lots are located in Susegana, Treviso, Italy. Unfortunately, there are no loading facilities on-site, dismantling and loading will be at the cost of the purchaser. Hsdpfoz I Szqjx Airow

Condition: used, used good condition low mileage cleaned functionality tested Hodpfx Ajz Np Ixoirow Manufacturer: Hoffmann Model: MU X-line Stop for stub tenon Stop for miter cut New price approx.: 1900.00 Location: 97447 Gerolzhofen, free loading, unpacked Handover in the current condition as inspected, without warranty or guarantee.

Condition: reconditioned (used), Year of construction: 2000, Fritsch CTR croissant production line, manufactured in 2000. Hsdpfx Aijz Ia Nvsrow The line includes: 1. Fritsch calibrator KK 88-700-L 2. Fritsch infeed conveyor with flour dispenser 3. Fritsch cutting and rotating unit CTR-700-30-L 4. Fritsch winding machine for filled products FRH-400-L 5. Fritsch winding machine for unfilled products CRH-120-400-L 6. Fritsch filler Used and refurbished. Manufactured in Germany. Price upon request.

Condition: used, Reusable glass bottle filling line for filling fruit juice and juice mix drinks. The filling line consists of the following components: - New glass bottle lifter (Kettner, 1985) with pallet loading, gripper head, empty pallet removal, bottle table and intermediate layer remover - Empty palletiser (Kettner 1994) with pallet loading, gripper head, crate table and empty pallet removal - Unpacker (Kettner, 2002) with packing heads and gripper tulips - Crate washer (Bohrer), crate cleaning trough with two crate turners - Unscrewing machine (Adelski, approx. 1990) with 12 unscrewing heads - Bottle cleaning machine (Krones, 1994) single-end machine - Empty bottle inspector (Heuft) for checking the base, mouth, side walls, thread and residual liquid - Filler (Bertolaso, approx. 1990) for hot filling with 60 filling valves and capper for twist-off caps. - Tunnel cooler (Niko, 2015) for spray cooling of the filled beverage - Labelling machine (Krones) for cold glue labelling of belly, back and neck labels - Label inspection (Metec) - Inkjet printer (Markem-Imaje, 2012) for best-before date marking - Packer (Kettner, 1989) with packing heads and gripping tulips - Palletiser (Kettner) with empty pallet feeding, gripping head and raised working platform with control panel - Pallet securing device (Bornbinder) for strapping the pallets with a horizontally applied cord - Film wrapper (Robopac) for wrapping the pallets with stretch film Additional title: Returnable bottle filling line with palletising, year of manufacture 1985 - 2015 Capacity: 15000 bo/h referring to 0.5 l bottles Formats: 0.2 l; 0.25 l; 0.5 l; 0.75 l, 1.0 l bottles / 6-packs, 12-packs, 20-packs and 30-packs / twist-off caps / Euro and brewery pallets Operation / Control: S7-300 (pallet wrapper), otherwise S5 or Schleicher control system Hodpfx Ajz D Hmmeirjw Features: New glass lifter, depalletiser, unpacker, crate washer, unscrewer, bottle cleaning machine, empty bottle inspector, Glass bottle filler and capper, tunnel cooler, labelling machine, label inspector, date coder, packer, palletiser, pallet strapper, pallet wrapper

Condition: used, The set on offer is a complete MAREL SmartLine Grader weighing and sorting system in Dual Lane configuration, featuring two independent belts, each served by its own row of sorting output bins on the side of the machine, allowing for higher throughput than a single-lane configuration. The set additionally includes 2 infeed conveyors, model INF-PROL 031-02, 2 dynamic weighing stations (Dynamic Weighing Unit, model DWU, year 2014, range 250 g–6 kg), and 2 sorting stations (target batcher). The system is designed mainly for fish products but works well with most other food products too. How does the MAREL SmartLine Grader Dual Lane system work? Product is fed onto the line via two infeed conveyors, model INF-PROL 031-02, which deliver raw material to the weighing stations in a steady, controlled manner. Each of the two dynamic weighing stations (DWU) measures the weight of individual product pieces within a range of 250 g to 6 kg, passing the data to the control system. Based on the measured weight and programmed sorting criteria, the two sorting stations (target batcher) direct the product to the appropriate output bins, enabling precise batching to a target weight with minimal giveaway. The open, hygienic IP69K-rated construction allows for fast disassembly and pressure washdown, while an intuitive touchscreen panel provides ongoing monitoring and control of the sorting process. Key advantages of the MAREL SmartLine Grader Dual Lane system The Dual Lane configuration, with two independent belts and separate rows of sorting output bins, handles significantly higher production volumes than single-lane systems while maintaining high sorting precision. The doubled set of infeed conveyors, weighing stations, and sorting stations allows for two independent lines to run in parallel or for doubled throughput on a single process. The high weighing accuracy of the DWU stations minimizes product giveaway, translating directly into raw material savings across overall production. The hygienic, open-frame IP69K-rated construction, together with fast disassembly and reassembly, makes it easier to maintain the high cleanliness standards required in the food industry, while integration with MAREL software provides real-time production insight and batch traceability. Technical specifications of the MAREL SmartLine Grader Dual Lane system MAREL SmartLine Grader Dual Lane Manufacturer: MAREL (JBT Marel) Model: SmartLine Grader – Dual Lane configuration Number of lanes: 2 independent belts, each with its own row of sorting output bins Protection rating: IP69K Control panel: touchscreen, with real-time monitoring and reporting software Application: mainly fish products, also works well with most other food products Infeed conveyors (2x INFEED Conveyor) Model: INF-PROL 031-02 Quantity included: 2 units Dynamic weighing stations (2x DWU) Model: DWU (Dynamic Weighing Unit) Hsdpfxez Haq De Airew Year of manufacture: 2014 Weighing range: 250 g – 6 kg Quantity included: 2 units Sorting stations (2x target batcher) Quantity included: 2 units Application of the MAREL SmartLine Grader Dual Lane system

Condition: used, Year of construction: 2017, Overview Complete automatic canning line for beer by American Beer Equipment (ABE), built around the LINCAN 35 inline can filler and seamer. The line runs from the can depalletizer through the twister rinser, atmospheric filling and lid seaming to the air knife dryer. It is fully operational, with maintenance up to date and the latest software installed. Technical data - Year of manufacture: 2017 (LINCAN 35) - Capacity: rated 35 cans/min on 0.33 L cans; about 1,500 cans/h in production - Can formats: 0.33 L and 0.44 L in use; compatible with 0.355, 0.375, 0.5 and 0.568 L cans - Filling: atmospheric, for beer at about 3 °C, CO2 purge of each can before filling - Utilities: compressed air at 100 psi (approx. 7 bar), CO2 at 60 psi (approx. 4 bar) - Cleaning: CIP function started from the HMI - Control: touchscreen HMI with daily, weekly, monthly and lifetime can counters - Construction: stainless steel Scope of Delivery - Can depalletizer | Norland | YELLOW JACKET | for aluminium cans up to 24 oz, pallets 56 x 44 in with tier sheets, approx. 340 kg, footprint approx. 2.7 x 2.7 m with conveyor, height approx. 3.5 m - Twister rinser | inclined can twister with rinsing - Atmospheric can filler | LINCAN 35 | 7 inline filling nozzles with level probes, CO2 purge - Can seamer | LINCAN 35 | seaming unit upgraded, retaining bar added on the lid feed - Drying unit | air knife on the discharge conveyor - Documentation | operator manuals, printed and PDF Condition Fully operational and in very good condition, inspected in production. Maintenance up to date, software updated, seaming and lid feed improved. Hsdpfxjz Hziuo Airow Availability Immediately. Location: Spain.

Condition: used, Year of construction: 2019, Overview Complete craft-beer bottling line for 0.33 L glass bottles, currently in operation. The heart of the line is an ABE GLASSPAK 66 automatic rotary isobaric monobloc that rinses, fills, crowns and post-rinses up to 4,000 bottles/h. A layer depalletizer feeds the filler; a linear labeller with lot coder, an accumulation table and a case sealer complete the end of line. Technical data - Product: beer, glass bottles - Capacity: up to 4,000 bottles/h at 0.33 L - Filling: isobaric (counter-pressure), 18 filling valves - Closure: 26 mm crown caps - Filler electrical supply: 380-415 V, 3-phase, 50 Hz - Year of manufacture (filler): 2019 Scope of Delivery - Bottle depalletizer | Cordero Maquinaria | layer depalletizer with overhead sweep frame, electric hoist and bottle infeed table, 400 V, 50 Hz - Isobaric filling monobloc | ABE | GLASSPAK 66 | inverting pre-rinser, vacuum and CO2 purge, 18 counter-pressure filling valves, 7-head crown capper, post-rinse and drying, touch panel, SEW 2.2 kW main drive, 4,000 bottles/h | 2019 - Pump cart | ABE | diaphragm pump for product feed | 2019 - Linear labeller | Basic Total | self-adhesive labels, bottle diameters 15-100 mm - Lot coder | Hitachi | UX-B160W | continuous ink-jet printer - Accumulation table | rotary, with infeed and accumulation controls - Case sealer | SOCO System | T-10 | with extendable roller conveyor Documentation Operator's manuals V1.2 and V1.3 and parts pictorial V2.2 for the GLASSPAK 66, labeller manual, original invoice. Condition Currently in operation. Hsdpfx Aiez Hz S Ajrew Availability Available now. Location: Spain.

Condition: good (used), Year of construction: 2010, functionality: fully functional, milling height: 180 mm, WEINIG NKT Dovetail Grooving Line – Double Unit DP20 An industrial dovetail grooving and gluing machine – developed for maximum precision and efficiency. Technical specifications: Wood input length: min. 130 mm | max. 1000 mm Wood output length: min. 3700 mm | max. 7400 mm (half lengths possible!) Wood cross-section: min. 20 x 40 mm | max. 80 x 180 mm Cutter diameter: 370 mm Dovetail design: Vertical / Horizontal, 10/11 dovetails, 3.8 mm pitch Glue application: 2-sided, PVAC white glue Connection power: 80 kW Note: The machine is currently disassembled and is in our warehouse. An inspection is possible by appointment. Scope of supply: WEINIG NKT Double Unit DP20 including control unit Integrated gluing station for 2-sided application Operating manual & documentation Hydromat 17B (7 spindles) General information Manufacturer: Weinig AG Model: Hydromat 17B // 7 spindles (various tools) Type: High-performance profiling milling machine / planing and rabbeting machine Year of manufacture: 1989 Operating voltage: 380 V / 50 Hz Bottom-Right-Left-Right-Left-Top-Bottom table, fixed Description Heavy-duty, high-performance planing and rabbeting machine made of vibration-damping and torsion-resistant cast iron components in a modular system. Designed for precise and economical woodworking with high continuous output. Mechanical feed, adjustable in the range of 5 – 35 m/min, feed motor 5.5 kW (7.5 HP). Surfacing table 2 m long, quick adjustment available. Chip removal for surfacing and jointing spindles, adjustment range 10 mm each. Technical data • Feed speed: 5 – 35 m/min, mechanical • Feed motor: 5.5 kW / 7.5 HP • Operating voltage: 380 V / 50 Hz Hedpfx Aez E Awqoirsw • Table length: 2000 mm • Adjustment range of chip removal: 10 mm (surfacing and jointing side) • Machine design: Without counter bearing, in high-performance design

Condition: used, Machine description Used continuous finishing line for steel flat bar and strip, second-hand and for sale complete with 15 in-line stations. Entry section: DIMECO decoiler with expanding mandrel, roller straightener, welder, drive unit and loop table. Surface preparation: FISHER inline shot blasting machine with dust collector and suspended brush-shear. Sizing section: cold, dry 2-high rolling stand, continuous tension straightener and Zumbach USYS laser gauge. Exit section: pneumatic shear, cut-to-length shear, bar run-out conveyor and product-specific coil recoiler. Schneider Electric Magelis operator panel with bar and coil modes. Capacities, year of manufacture and installed power: not specified. Applications This descaling, cold rolling and sizing line converts hot-rolled strip or flat bar coils into shot-blasted, cold-rolled, straightened and gauged products, delivered as cut-to-length bars or coils. Typical buyers include steel mills, flat wire and strip producers, spring and blade manufacturers, stamping plants and flat product finishing centres. Key features / Advantages Complete finishing line from decoiling to packaging, with mechanical shot blast descaling instead of acid pickling. Components from active manufacturers (DIMECO, Zumbach, Schneider Electric) make spare parts easier to source. Bar or coil output on the same line. A second line of identical configuration is also for sale, and both can be purchased as a matched pair. Sold as-is, dismantling by the buyer, available now from All Metal, specialist in used industrial machinery. Configuration: 15 posts online Unwinder: DIMECO, expanding chuck Surface preparation: fisher nip fryer? Rolling: dry cold rolling cage (duo) Straightening: roller straightener + continuous tension straightener Measurement: laser Zumbach USYS Cut: pneumatic shear + shear for length cutting Exit: bar rail conveyor + dedicated product winder Production modes: barrel / crown Order: Schneider Electric Magelis HMI Processed products: plates and steel straps Sale: as is, dismantling at the buyer's expense Hodpfx Aez N Ahxjirsw

Condition: new, Year of construction: 2025, Metal picket fence roll forming machine MFP-1 was designed by our company to produce semi-round shape picket metal fence profile. This profile is widely used and popular among companies with business in manufacturing, installation and selling of metal fences. The production of the profile goes gradually, at first hemming forms on edges from the flat metal, and then the height of the profile and the semi-round shape are formed, at the last stage of rolling machine forms the rib in the profile center. Such number of forming stages makes it possible to ensure smooth sheet changes during rolling, as well as high quality of the final product. Hodom Twnlopfx Airow As a blank, you can use a strip of required width and length, to prepare it with pre-cut on other equipment – sheet metal slitting machine or guillotine shear. After roll forming, to make fence picket end look better, you can use special cutting press of our production. The working tools of such press have special round configuration and are the same as semi-round metal picket shape to make appropriate cutting. Those tools are made from special tool steel, and goes through process of hardening so ensure high requirements for the cutting tools of the equipment. Our company can produce as semi-automatic rolling machine for the metal fence pickets manufacturing and a manual punching press for it, as well as a fully automatic line. Such metal fence automatic line can have following components: console metal decoiler, a rolling machine equipped with an automatization system with the ability to program the number of required pickets for rolling and their lengths, automatic electric shear for cutting metal at the end and stacker part. Thus, cooperating with us, our customers can choose the best option for their manufacturing process according to their planned production volumes, budget, etc. For more details about metal picket fence roll forming machine MFP-1 please contact our sales department

Condition: new, Year of construction: 2025, Window drip cap roll forming machine PO-1 allows to produce “window trim” profile by rolling the sheet metal through forming rolls. A window trim is an element that is widely used in construction while windows installation. In the standard way the window trim is bent step by step using a manual folding machine. This is a cheaper, but more time-consuming process. The metal sheet must be pre-marked for each bending operation. Hsdpfxolwt Adj Airow Each bend is then performed using a manual bending machine. The operator must set the necessary dimensions according to the marks, fix the sheet metal with the machine"s fixation mechanism, and then bend it. The length of the window trim is limited to the maximum working length of the bending machine. Thus, each manual folding operation is time-consuming and the production process becomes expensive and inefficient. To improve the production process we offer the window drip cap roll forming machine PO-1. This machine rolls the window trim profile on both sides simultaneously in a single operation. The rolling speed is 10 m/min. The machine is equipped with 7 pairs of forming rolls. The minimum width of window trim is 120 mm when rolling on both sides at the same time and the maximum width is 610 mm. To change the width of the window trim, simply use the adjusting handle, which makes it very easy to adjust the machine to go from one trim width to the next. Thus, the adjustment process is not time-consuming. It’s also possible to roll the window drip cap on the machine in two steps.

Year of construction: 1988, condition: used, strip width (20) 44 - 320 mm strip thickness 0,66 – 4 mm strip cross section max. 930 mm² reference material (tensile strength) St42-2 (500 N/mm²) yield stress max. 280 N/mm² coil weight max. 4 t Hjdpfsbicz Hex Airow coil-dia max. 1.500 mm

Condition: new, Year of construction: 2024, Soffit panel roll forming line was designed by our company to produce wall soffit panels with different lengths. Line has automatic system so you can put length of panels and numbers you need and machine will produce it in automatic mode and cut it automatically. Machine has special cutting shear to cut panels as well. Line can be equipped with manual or automatic decoiler as an option. So it can be effective solution for soffit panels production Hjdpfsrqg U Dex Airow

Condition: excellent (used), Year of construction: 2000, The line is fully operational, modernized in 2019. Among others, : Hydraulic installations and control. minimum material thickness - 20mm max material thickness - 130mm Hodpfxoim Ez Ds Airow minimum material width - 30mm max material width - 130mm minimum input length of the material - 250mm max input length of the material - 1600mm minimum output length of the material - 250mm max output length of the material - 300mm

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Hjdpfxshzbipj Airow Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: reconditioned (used), Year of construction: 1996, No.: 2590k Hsdpfx Aisgbffvsrsw 1 used compounding-pelletizing line – output up to 1200 kg/h depending material, equipped with: Extruder Twin-screw THEYSOHN Type TSK 90 Screws 2x Ø 90 mm – 36 LD co-rotating intermeshing Segmented screws-and Cylinder, Water / Medium cooled Extruder Motor 255 kW-DC / Screw speed up to 300 r.p.m. 1x Side feeding extruder TSD 75 twin-screw with 3 kW 3x venting ports 1x Melt-Filter No. 1 type K –HS- Y sieve/Mesh 176 mm incl. Hydraulic Pack 1x Melt-Pump with motor 22 kW 1x Melt-Filter No. 2 type K-SWE 180 RS back-flush self-cleaning 1x Strand die-head with holes 32 x Ø3,5 mm 1x Strand cooling bath 620 x 5000 mm 1x Strand pelletizer SG 300 with 11 kW ResoTec Monitor control Board Inspection visit / demonstration shortly possible - date on appointment You´re welcome. More compounding pelletizing lines ex pour workshop available, > find our most-recent stock-list online on our homepage.

Condition: like new (used), Automatic line which has been used for producing 2 million toffee / candy apples over 6-8 week period. Complete lines available, to manufacture the toffee sauce, melt the chocolate, fire sticks into the apples and robotically dip them in sauce then flow wrap the finished product. Hjdpfx Aiohtv Uwsrsw

Condition: used, Depalletizer and Palletizer – Flema Star C-LC For NRW and Euro crates as well as Euro and beer pallets, 500 crates/hour, Year: 1996, empty crates in from left, full crates out to the right. Crate Unpacker – RICO UNO 1-Head Type 124 For NRW and Euro crates, head suitable for Euro 0.5l, NRW 0.5l, and Ale 0.33l/0.5l bottles, 350 crates/hour, Year: 2010, right-to-left operation. Bottle Cap and Cork Remover – ADELSKI Type PPE 2005 For NRW, Euro, and Ale 0.5l bottles, 2,000–12,500 bottles/hour, Year: , Operating hours: 8,500, right-to-left operation. Bottle Washer – PAC CB 14-0.5l-R-7 LII Compact For NRW, Euro, and Ale 0.33l and 0.5l bottles, 7,500 bottles/hour, Year: 1998, Machine No. 125, Operating hours: 14,175. Bottle Inspection – SYSCONA LC 10 FD Caustic control + metal detection, Year: 2007. Filler – ICS multiFILL-VST (EP) 960-24-240-6KK-6SV-125.6 For NRW, Euro, and Ale 0.33l and 0.5l bottles, incl. product pump, 6,000 bottles/hour, Year: 2011, Operating hours: 7,200, right-to-left operation. Labelling Machine – ANKER Roland 8/3 For NRW, Euro, and Ale 0.33l bottles, 7,000 bottles/hour, Year: 1998, Operating hours: 14,500, left-to-right operation. Inkjet Printer – Keyence MK-G1000 Year: 2022, currently configured for date coding on rear label of ANKER Roland 8/3. Crate Packer – RICO UNO 1-Head L-Machine For NRW and Euro crates, head suitable for Euro 0.5l, NRW 0.5l, and Ale 0.33l/0.5l bottles, 300 crates/hour, Year: 2012, left-to-right operation. Premixer – Jakü PM-E-30-2k Hjdjz Ri Rispfx Airow For degassing and carbonation, with product tank and 2K Bran+Lübbe pump, 35 hl/h, Year: 1992. Crate Washer – RICO 2500 1-Bath For NRW and Euro crates, 600 crates/hour, Year: 2012, right-to-left operation. 2 CIP Tanks, each 6 hl Steam-heated for filler CIP, with disk change system, Year: 2012.

Condition: good (used), Year of construction: 2000, functionality: unexamined, Equipment: documentation/manual, Eccentric press VSS, type LE 400 C, complete with LASA strip feed system. Press LE 400 C Table size 1250 x 895 mm Ram size 950 x 560 mm Hjdjz Rk Shepfx Airsw Weight 21,000 kg Nominal capacity 400 t (metric tons) Stroke rate 40/min Stroke length 450 mm Dimensions 1550 x 2900 x 3610 mm Unwinding reel – up to 4000 kg - Coil outer diameter – 1600 mm - Coil inner diameter – 450/550 mm - Strip width – 450 mm - Revolutions – max. up to 25/min LASA 400 strip straightening machine - Adjustable height - Speed – up to 70 m/min - Complete documentation - More information and detailed images available upon request - The straightening machine with unwinding reel can also be sold separately. Press – after inspection - Stroke adjustment and clutch-brake

Condition: used, Year of construction: 2024, functionality: fully functional, Corrugated line 5 ply. Fully renewd 2024, 1650mm width. Steam matic, boiler steam producing 2500 kg/h. Max pressure 19 bar. Speed up to 70 metr per min. 1.⁠ ⁠Total Length: 55 metr 2.⁠ ⁠Total Power: 150 kw 3.⁠ ⁠Frame with shaft 4.⁠ ⁠Corrugated paperboard marching: diameter of corrugated rouer, electric adjust speed moter used. 5.⁠ ⁠Double cylinder gum mounting marchine: On the adoption, inside two layers draw the gun, dascend to carry the paper lead the paper roller. Machine exists units: Hydraulic shaftless mill roll stands, Spindle ¢ 240mm, hyperbolic heavy rocker, expand chuck , multi-point brake, hydraulic drive lifting, panning left and right on the middle. Top paper preheat cylinders and core paper preheat cylinders. Both preheat 360 degress area. Single Facer Double Facer Blade scorer NC helical knife Glue system Gas system Steam system producing 2500 kg/h. Max pressure 19 bar. Working 12 bar. Hjdpsw R Sknefx Airew Top paper index 100g/㎡--180g/㎡ Ring crush index（N.m/g）≥8 (Water containing8-10%) Core paper index 80g/㎡--160g/㎡ Ring crush index（N.m/g）≥5.5 (Water containing8-10%) In paper index 90g/㎡--160g/㎡ Ring crush index（N.m/g）≥6 (Water containing8-10%)