Used roll forming lines for sale (84)

Condition: good (used), DREISTERN P3.100 Profiling Line – 16 driven stations and 2 × 18.5 kW Short title for platforms with character limits: DREISTERN P3.100 Profiling Line, 16 driven stations Platform data * Machine type: Profiling line / Roll forming line * Manufacturer: DREISTERN * Model: P3.100 * Year of manufacture: not known / to be added before publication * Condition: used, dismantled * Control system: not available For sale is a DREISTERN profiling line, type P3.100, with 18 stations, 16 of which are driven. The line is equipped with 16 profiling stands, 50 mm working shafts, quick-change plates, and two Bosch motors, each with 18.5 kW. Fpjdpfx Aozzyd Noatjl The modular design with mechanical quick clamps and quick-change plates is suitable as a solid mechanical base for customer-specific roll forming applications. A constructive expansion with additional stations is possible. According to the previous operator, the line operated flawlessly until it was dismantled at the customer's site. The control system is not available and is not included in the scope of supply. Recommissioning or control system adaptation by the buyer is therefore necessary. Machine bed and drive * Production direction: from left to right * Axle distance: 330 mm * 18 stations in total * 16 stations driven, with 16 gearboxes * Quick-change plates * Mechanical quick clamps * Coolant piping * 2 × Bosch motor, each 18.5 kW Profiling stands * Number in scope of supply: 16 pieces * Tool width per stand: 275 mm * Working shaft diameter: 50 mm * Working shaft connection: 30 mm with groove * Fixed lower shaft * Axial adjustment * Adjustment range lower to upper shaft: 80–170 mm Gearboxes * Worm gear ratio: 1:7.5 * Lower/upper shaft ratio: 1:1 Scope of supply * Machine bed with gearbox support * Infeed table * Pneumatic measuring wheel unit * Special straightening device * 16 gearboxes * 16 profiling stands * 2 Bosch motors, each 18.5 kW * 32 universal joints

Condition: good (used), DREISTERN P3.100.40/3 Profiling Line – 44 driven stations with flying shear Short title for platforms with character limitations: DREISTERN P3.100 Profiling Line, 44 Stations + Shear Platform Data * Machine Type: Profiling Line / Roll Forming Line * Manufacturer: DREISTERN-WERK * Model: P3.100.40/3 * Year of Manufacture: 2002 * Factory Number: 02 098 * Order Number: 38933-46 * Condition: Used, disassembled * Control System: Not available For sale is a comprehensively equipped DREISTERN profiling line, type P3.100.40/3, with 48 stations, 44 of which are driven, as well as an inline shear (“flying shear”). The line features quick-change plates, mechanical quick clamps, and a coolant piping system. Due to the large number of profiling stations, it is particularly suitable as a mechanical base for demanding, customer-specific roll forming applications. An expansion with additional stations is structurally possible. According to the previous operator, the line operated flawlessly until it was disassembled at the customer's plant. The control system is not available and is not included in the scope of supply. Recommissioning or control system adaptation by the buyer is therefore necessary. Machine Bed and Drive * Production direction: from right to left * Center distance: 330 mm * 48 stations total Fpjdjzzyd Ajpfx Aatol * 44 stations driven, with 44 gearboxes * Quick-change plates * Mechanical quick clamps * Coolant piping system * 1 × Baumüller DC motor, 42 kW * 1 × Baumüller DC motor, 15 kW Profiling Frames * Number included in scope of supply: 44 pieces * Tool width per frame: 275 mm * Working shaft diameter: 50 mm * Working shaft connection: 30 mm with keyway * Lower shaft mostly fixed; 6 frames with adjustable lower shaft * Axial adjustment * Adjustment range lower to upper shaft: 80–170 mm Gearboxes * Worm gear ratio: 1:21 * Lower/upper shaft ratio: 1:1 Inline Shear * Travel path: 1,900 mm * Profile rail guidance * Ball screw drive * Bosch servo motor * Valve block with punching unit * Folding table length: 3,000 mm * Emergency stop Scope of Supply * Machine bed with gearbox support * Infeed table * Pneumatic measuring wheel unit * Straightening device * Belt filter unit, 800 liters * Hydraulic unit for the shear * 44 gearboxes * 44 profiling frames * 2 Baumüller DC motors * 66 universal joints * Inline shear according to the above description

Condition: excellent (used), sinus profile 15/75 input : 1000mm only output: 830 mm Fpodezyytuepfx Aatjl work automatically, with cutting scissors.

Condition: excellent (used), round Gutter. fi100 Fodpozyytnefx Aatepl input material 333mm dx53d quality of material automatic cutting machine works with air

Condition: excellent (used), round gutter roll forming line: 14 stations. manual de-coiler, precutting. automatic measurement. Fpedszyythepfx Aatel Dx53d quality working. input 333mm

Condition: excellent (used), Tile Imitation T-40/350 input coil: 1250mm output : 1114mm auto stacker Fsdpfxszyytbo Aatopl 16 stations.

Condition: excellent (used), We offer this very good FACADE PANELL ROLL FORMING MACHINE German machinery Input: 250mm-600mm. Usually, we used to produce from 417mm input= output 310mm Micro design or flat design: 16 stations. Fpjdozyyr Dspfx Aatjl The machine has two options for forming the final product. 1) with Fuge (space joint) and without Fuge (no space joint). so two sets of roll formers.

Condition: excellent (used), Roll Former- Trapez t18/120 input coils; 1000mm ; 1250mm output: 835mm/1085mm thickness:0.3-0.70mm 20 stations Fpsdezyyq Hepfx Aatel

Condition: excellent (used), Roll former- Trapez T35/196 Input coils: 1000 mm, 1250mm Output: 1000mm Fodpfx Aozycn Ioatepl thickness: 0.30-0.70mm 27 stations.

Condition: excellent (used), functionality: fully functional, We offer this very good FACADE PANEL ROLL FORMING machine. Input: 420mm output: 310mm Fodpfezyclmjx Aatspl Decoiler, 16 stations, automatic cutting.

Condition: ready for operation (used), Year of construction: 2015, operating hours: 2,600 h, functionality: fully functional, machine/vehicle number: 15243485, type of input current: three-phase, total width: 3,600 mm, total length: 39,700 mm, total height: 1,900 mm, input voltage: 380 V, overall weight: 19,700 kg, The line consists of double decoiler, pre-heating section, set of forming rollers, foaming machine, polymerization bench, cutting system with flying saw, belt conveyor, stacking bench with return and a control panel. The line is equipped with a COMBI system allowing quick profile type changeover. Fodpfx Aaszwb D Njtspl The line produces two profiles: 1. H39mm, coil width 120mm, thickness 0.2-0.25mm 2. H45mm, coil width 136mm, thickness 0.2-0.25mm Technical Specifications: - maximum line speed - 36 m/min - maximum profile length - 6.5 m - maximum coil weight - 500 kg - the line power consumption approx. 36-40 kW IMPORTANT: the line currently produces only non-perforated profiles. However, perforated module can be integrated into the line for extra cost

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, Complete P20 & P30 HVAC Duct Flange Profile Roll Forming Lines with Butyl Sealant System For sale is a complete set of two professional roll forming lines for the production of P20 and P30 flange profiles, used in the manufacturing of rectangular HVAC ducts and fittings. The set includes: - P20 flange profile production line - P30 flange profile production line Both machines are equipped with an integrated butyl sealant application system. Depending on production requirements, the profiles can be manufactured with or without factory-applied butyl sealant. This provides full flexibility and allows the finished profiles to be adapted to different duct manufacturing technologies and customer requirements. The machines perform the complete production process – from coil decoiling, through multi-stage roll forming, to automatic cutting of the finished profile to the required length. Technical highlights - 18 roll forming stations Fpjdpfxszx Rz He Aatel - Automatic PLC-controlled cutting system - Production speed up to 9 m/min without sealant application - Production speed up to 5 m/min with butyl sealant application - Integrated butyl sealant application system - Complete production lines for P20 and P30 profiles Both machines are in very good technical condition. Since new, they have been used exclusively for the production needs of our own HVAC duct manufacturing facility. They have not been used for continuous mass production of profiles for commercial sale, therefore their overall level of utilisation is relatively low. Both production lines are fully operational, properly adjusted, tested and ready for immediate production. The machines are offered as a complete P20 + P30 set, allowing the buyer to establish in-house production of the two main flange profile sizes commonly used in the manufacturing of rectangular HVAC ducts and fittings. Relocation and commissioning support We can provide technical assistance with dismantling and relocation of the machines. We can also support the buyer with installation, adjustment, testing and commissioning at the new production facility, helping to ensure that both lines are properly set up and ready for production after relocation. The machines can be inspected while in operation, and production tests can be carried out prior to purchase. The indicated price is NET and VAT will be added where applicable.

Condition: used, Year of construction: 2006, functionality: fully functional, machine/vehicle number: TEL-178600-558-98, working width: 1,250 mm, The production line was fully operational until it was dismantled. It was taken out of service solely due to a production upgrade/change in manufacturing technology. The machine is currently dismantled and prepared for transport; therefore, a live demonstration is not possible. Prior to dismantling, the line operated without any issues and was regularly maintained. We offer two complete roll forming lines for sale, available either individually or as a package. Manufacturer: SAMESOR Year of manufacture: 1998 Fpsdpfozmzhmsx Aatsl SERIAL: TEL-178600-558-98 Manufacturer: AJV-MACHINE Year of manufacture: 2006 SERIAL: AJV24/1100-169

Condition: used, Year of construction: 2003, functionality: fully functional, machine/vehicle number: 2188, input voltage: 400 V, product width (max.): 1,500 mm, SWAH LCP-01 A high-performance, automated production line for the manufacturing of rectangular ductwork. The SWAH LCP-01 is a robust European system designed to transform coil material into finished, reinforced rectangular duct sections with maximum efficiency. Specifications • Manufacturer: SWAH s.r.o. (Czech Republic) • Model: LCP-01 • Year of Manufacture: 2003 • Serial No. (M. No.): 2188 • Application: Fully automated production of rectangular ducts from coils. This line is a complete system, including • 4 Decoilers Station: To hold and feed heavy sheet metal coils (allowing for quick changes between different material thicknesses or widths). • Straightening & Leveling Unit: Ensures the sheet metal is perfectly flat before processing. • Beading/Stiffening Station: Automatically forms longitudinal stiffening ribs (V-profile) to ensure the structural integrity of the rectangular ducts. • Automated Notching & Cutting: High-precision hydraulic system for cutting to the exact programmed length. • Folding/Bending: Processes the material for easy "L" or "U" shape formation or full duct sections. • Material Thickness: Galvanized Steel: 0.4 mm – 1.2 mm Stainless Steel: 0.4 mm – 0.8 mm Condition & Availability Fpodpfxjzbh Auo Aatsl • Status: Fully operational and in good working condition. • Ready for delivery

Condition: new, Year of construction: 2026, functionality: fully functional, total width: 2,300 mm, total length: 9,000 mm, total height: 2,300 mm, overall weight: 9,000 kg, Mobile Roll Forming Machine for Frameless Steel Arch Buildings Automatic Production Line for Self-Supporting Steel Hangars and Arch Roofs The mobile roll forming machine is designed for the on-site production of self-supporting curved steel panels used for the construction of frameless steel buildings, arch hangars and self-supporting metal roofs. The technology makes it possible to construct large-span steel buildings without a conventional internal steel frame. Steel coil is formed into a structural profile, cut to the required length and then curved to the required building radius. Several curved panels are connected together using a special seaming machine to form a strong, continuous and self-supporting arch structure. The equipment can be used for the construction of: frameless steel hangars aircraft hangars agricultural buildings grain and machinery storage buildings warehouses industrial buildings workshops garages livestock buildings sports facilities self-supporting steel roofs temporary buildings military and logistics storage facilities Mobile Production Directly at the Construction Site One of the main advantages of this technology is the possibility of producing the complete structural panels directly at the construction site. The main forming and curving equipment is installed on a mobile trailer chassis. The machine can therefore be transported to the building site, where steel coils are converted into finished structural arch panels. This is particularly important for long panels that would otherwise be difficult or expensive to transport. The supplied machine has two axles and eight tyres intended for movement around the construction site. Production Process Fpodpoztwx Usfx Aatol The complete production process consists of several stages: Steel Coil → Decoiling → Straight Profile Forming → Cutting to Length → Curving → Panel Seaming → Lifting → Installation The supplied technical manual describes the machine as a combination of a roll forming section and an arch bending section, with electrically driven forming and bending and hydraulic cutting. Main Technical Specifications Parameter Specification Machine type Mobile arch sheet roll forming line Application Frameless / self-supporting steel buildings Feeding width 1000 mm Effective profile width Approx. 610 mm Material thickness 0.8–1.5 mm Forming stations 13 + 1 Straight panel forming speed Up to 15 m/min Arch panel forming / curving speed Up to 13 m/min Seaming speed Approx. 6 m/min Forming motor 7.5 kW Curving / bending motor 5.5 kW Cutting motor 4.0 kW Additional drive 3.0 kW Total installed motor power Approx. 20 kW Cutting system Hydraulic Cutting tool material Cr12MoV, heat treated Roll material 45# steel, chromed and hardened Roller hardness HRC 58–62 Control system PLC Machine dimensions Approx. 9000 × 2230 × 2200 mm Machine weight Approx. 9000 kg Chassis 2 axles / 8 tyres Different Profile Sizes Available The machine can also be manufactured for different structural profile dimensions according to the required building span and application Available configurations may include different: coil feeding widths finished profile widths profile depths steel thicknesses arch radii building spans For example, depending on machine configuration, profiles can be designed for relatively small buildings as well as large-span self-supporting arch structures

Condition: repair required (used), Year of construction: 2007, Roller profiling line for manufacturing profiles for dry construction, without a hydraulic unit. Location: In our workshop. Fpedpfxjzy Ekfo Aatel

Condition: new, Year of construction: 2026, Automatic Roll Forming Line for Light Gauge Steel Frame Production This automatic roll forming line is designed for manufacturing Light Gauge Steel (LGS) and Cold Formed Steel (CFS) structural profiles used for steel frame houses, modular buildings, commercial buildings and prefabricated construction systems. The production line automatically performs feeding, leveling, punching, roll forming, profile marking and hydraulic cutting according to digital production data. It is an ideal solution for manufacturers of: Light Gauge Steel structures Steel frame houses Prefabricated buildings Modular buildings Tiny houses Commercial steel structures Residential steel framing Cold formed steel construction systems Flexible Machine Configuration The roll forming line can be supplied in two different configurations depending on production requirements. Fixed Profile Machine Designed for manufacturers producing one profile size with maximum productivity and simplified machine setup. Multi-Profile Roll Forming Machine An adjustable roll forming system capable of producing several profile widths on one machine by changing the roll forming configuration. This solution provides greater production flexibility while reducing investment costs compared with purchasing multiple dedicated production lines. Complete Automatic Production Process The machine automatically performs the following operations: Coil feeding Strip leveling Servo punching Hole punching Slot punching Service hole punching Roll forming Profile identification marking Hydraulic cutting to length Finished profile discharge The production line is designed to work with professional steel frame design software. The operator imports production data generated from a building design into the machine control system. Based on this information the machine automatically manufactures every structural member including: wall studs tracks floor joists roof trusses rafters beams structural reinforcements Each component is produced with the correct length, punching pattern and identification marking required for final assembly. Fpedpfx Aaozrt Ivstsl Automatic Profile Marking Each profile can be automatically marked during production. Typical marking information includes: Profile number Wall identification Member position Assembly reference Project identification Automatic marking significantly simplifies profile sorting and speeds up on-site assembly. Instead of manually identifying every component, installers receive a complete production kit with every profile clearly identified. Automatic Punching System All punching operations are synchronized with the roll forming process to achieve high accuracy and repeatability. Main Advantages Fully automatic production Computer controlled manufacturing Automatic profile marking Servo punching system Hydraulic cutting High dimensional accuracy Reduced material waste Fast production Flexible profile sizes Suitable for custom house projects Reduced manual labour Easy assembly thanks to profile identification Applications Technical Specifications Typical options include: Single-profile roll forming machine Multi-profile adjustable machine Automatic profile marking Servo punching Hydraulic cutting Automatic decoiler Hydraulic decoiler Computer control system Production management software compatibility

Condition: new, Year of construction: 2026, total width: 750 mm, total length: 2,900 mm, total height: 1,160 mm, warranty duration: 12 months, overall weight: 400 kg, Compact roll forming equipment for producing metal rainwater downpipes This portable roll forming machine is designed for the production of rectangular metal downspouts and rainwater downpipes from pre-painted or coated sheet steel. The machine progressively forms a flat metal strip into a finished rectangular profile suitable for residential, commercial and industrial rainwater drainage systems. The dimensions and geometry of the finished downpipe can be manufactured according to the customer’s technical requirements. The roll tooling is designed for a specific rectangular profile, taking into account the required width, height, corner shape, surface pattern, material thickness and connection type. Fjdpezrnxcofx Aatspl The machine is suitable for manufacturers of: rectangular metal downspouts; rainwater downpipes; roof drainage systems; gutter and downspout components; roofing accessories; façade and sheet-metal products; custom cold-formed metal profiles. Its compact size and relatively low weight make it suitable for small workshops, roofing companies and production sites where a large stationary roll forming line is not required. Custom profile dimensions The finished profile is produced according to the customer’s drawing, sample or technical specification. The machine is therefore supplied as a custom rectangular downspout roll former, configured for the required finished product. The basic production process is: Decoiler → Roll forming system → Manual saw cutting Main advantages Compact and portable construction Custom tooling for the required downpipe size Production directly from coated sheet steel Suitable for pre-painted and galvanized material Gradual roll forming with controlled material deformation Low installed motor power Simple operation and maintenance Suitable for small-batch and regular production Finished products can be cut to the required length Reduced dependence on purchased ready-made downpipes Suitable for workshops with limited production space Material The standard configuration is designed for coated sheet steel with a thickness of approximately 0.4–0.5 mm. Depending on the agreed configuration, the machine may process: pre-painted steel; galvanized steel; polymer-coated sheet steel; other thin sheet-metal materials after technical approval. The exact material grade, tensile strength, thickness and coating must be specified before the roll tooling is designed. Technical specifications: Machine type Portable roll forming machine Finished product Rectangular metal downspout / downpipe Profile dimensions According to customer specification Material Coated sheet steel Material thickness Approx. 0.4–0.5 mm Forming speed Approx. 3–8 m/min Main motor power 3 kW Transmission Gear and sprocket drive Auxiliary forming elements Polyurethane wheels Cutting system Manual circular saw Machine dimensions Approx. 2860 × 730 × 1160 mm Machine weight Approx. 400 kg Electrical supply 380 V, 50 Hz, 3-phase* Compact machine design This makes it suitable for: roofing contractors; rainwater system manufacturers; sheet-metal workshops; gutter and downpipe producers; building component manufacturers; small and medium-sized production facilities; companies producing custom roofing accessories. Scope of supply A custom set of roll forming tools will then be designed for the required product.

Condition: excellent (used), Schlebach SPA Profiling machine for continuous production of angle standing seams with a seam height of 25mm. The machine is equipped with: ✅ a hydraulic separating device for precisely perpendicular removal of the forming tools after profiling. Fpodpfezyy Rgjx Aatel ✅ millimeter-accurate length measurement ✅ a control system that includes length and quantity settings ✅ a collection container for waste ✅ a 400V power connection

Condition: excellent (used), Profiling machine by Ras Inventory number: 3954 Manufacturer: Ras Type: Ras 22.12 * 11 stations * Shaft diameter: 28 mm * Band width: 150 mm * Band thickness: 1.2 mm * Flying hydraulic shear Fpodpfx Aajzyy N Aotol * Connected power: 5.5 kW

Condition: excellent (used), Profiling system Ras Inventory no. 3949 Manufacturer: Ras Type: Ras 29.03 * 11 stations * Shaft diameter 28 mm Fpodpfx Aozyytzoatsl * Strip width: 150 mm * Strip thickness: 1.5 mm * Flying hydraulic shear * Connected power: 11.5 kW

Condition: excellent (used), Lightly used automatic TC, TU, TZ profile production lines, designed for manufacturing and roll forming TC, TU, TZ profiles up to 1.5 mm metal thickness. Technical Specification: Manufactured in: Estonia Adjustable profile height: 100 – 250 mm Fpedpfx Aajx Sx R Sotsl Profile width: 50 mm Profile edge (folded): 15 mm Minimum rollable sheet thickness: 1 mm Maximum rollable sheet thickness: 1.5 mm Roll distance: 300 mm Machine dimensions: 900 x 4000 mm The machine is not equipped with a guillotine or perforating rolls. Operation is straightforward, controlled via two buttons. If you have further questions, we will be happy to answer them.

Condition: good (used), Schlebach Mini Prof Plus ☑️Immediately available, no delivery time☑️ Universal machine for the production of double standing seam profiles 25 from sheet material, coils, or cut-to-size pieces in a single pass. The machine is equipped with: ✅ Profiling rollers for 25mm seam height ✅ 230V connection ✅ A manual slitting shear RS for cross-cutting ✅ A slitting knife LS for cutting to width Fsdpszxrg Refx Aatopl ✅ An electromechanical counter (accurate to the cm) ✅ Bending capacity: 0.8mm (zinc, aluminum & copper), 0.7mm steel sheet Condition: • Good technical condition • Good optical condition • Weight: approx. 315kg An inspection and test run are possible by arrangement. The price is €14,250 net, plus VAT, totaling €16,957.50 gross. You will receive an invoice with VAT shown.

Condition: used, Cassettes + cutters for a roll forming machine used in the production of trapezoidal sheet metal. Two different profiles can be produced. Fedpfx Aaezvgwfotepl H = 158 mm x W = 750 mm H = 153 mm x W = 840 mm Details can be found in the photos. Processable sheet metal: Aluminum + steel in 0.75 - 1.5 mm Consisting of a total of: - Cassette 1 for profile 153 and 158 - Cassette 2 for profile 153 and 158 - Cassette 3 for profile 153 and 158 - Cassette 4 for profile 153 - Cassette 4 for profile 158 - Cassette 5 for profile 153 - Cassette 5 for profile 158 - Cassette 6 for profile 153 - Cassette 6 for profile 158 - Cutter for profile 153 - Cutter for profile 158 All items come from ongoing production; the sale is due to a product changeover. This includes only the cassettes + cutters, without drives, coils, shears, etc. Total weight: approx. 86,000 kg

Condition: new, Year of construction: 2026, functionality: fully functional, HawkTech LC-5005 – Pittsburgh Lock Machine for HVAC Duct Fabrication The LC-5005 forms the Pittsburgh lock seam on square and rectangular HVAC duct components. With 7 pairs of vertical forming shafts (each with left, middle, and right rolls), the profile is gradually formed, resulting in a clean and consistent seam. The upper section automatically adjusts to sheet thickness via a double-head stud and disc spring – no manual readjustment is needed during normal operation. Multiple lock profiles and combinations can be produced (Pittsburgh lock, drive cleat, and more). Compact and lightweight (360 kg) with a small footprint, the machine is easy to move, simple to adjust, and reliable – ideal for on-site duct fabrication as well as workshop use in industrial plants, hotels, and shopping centers. Technical data: Model: LC-5005 Motor power: 2.2 kW (Y100L1-4, three-phase) Voltage: 220 / 380 / 415 V (reversing switch QX1-13N1) Sheet thickness: 0.5 – 1.2 mm (drive cleat rolls: < 0.8 mm) Forming shafts: 7 pairs, 3 rolls each Dimensions (L × W × H): 1,520 × 630 × 1,010 mm Weight: 360 kg Scope of delivery: LC-5005 Pittsburgh lock machine Set of Allen keys (5, 6, 8, 10, 12 mm) Operating manual (CZ/EN) Fjdoy Swnpopfx Aatspl Quality certificate