Used Contour Edge Banding Machine for sale (66,678)

Condition: excellent (used), Year of construction: 1993, max. edge thickness coils 0.2 - 3 mm max. edge thickness solid strips15 mm feed speed 12/ 18 m/min glue plot heating time approx. 6 min autom. strip magazine coil magazine granulate heating pot flush trimming unit radius trimming unit operating panel extendable work piece support noice cancelation hood Chodpfefbr S Rex Ai Rjd machine length 3800 mm Advise used machines: • Technical data without obligation, mistake and intermediate sale reserve. • Price is considered ex-location price • All articles or machines are bought as seen without any entitlement on warranty. • It is left to the choice of the buyer to view the machines before at its location. • Special arrangements are possible but only valid in written form. (We answer your inquiries only with stated address + telephone number!)

Condition: used, Year of construction: 1998, Used machine Year of manufacture: 1998 Proven quick heating tank; heating time approx. 5 minutes. Safety interlock for the application roller; the roller engages only after reaching operating temperature. Centrally height-adjustable upper pressure bar. Edge feeding and roll separation pneumatically controlled. Connected load: approx. 11.5 kW, heating power 4.5 kW, frequency inverter 300 Hz, 4 kVA. HF crosscut saw unit: electrically and pneumatically controlled, motor power 0.37 kW. Saw blade diameter: 100 mm HF flush milling unit: for radius, straight and chamfer milling. Crosscutting from rolls up to 3 mm. Edgebanding and crosscutting up to 5 mm. Minimum workpiece length: 260 mm Minimum workpiece width: 90 mm Workpiece thickness: Chamfer milling from 10 mm / radius milling from 13 mm / max. 45 mm Codow Tfw Hspfx Ai Rohd Extendable workpiece support at front. Digital position display for feed height adjustment, edge thickness, and milling. With chassis. With heated infeed ruler. Compressed air connection: 6 bar Central extraction port: 100 mm Dimensions (L x W x H): 3115 x 1230 x 1200 mm Approx. 560 kg Availability: short notice Storage location: Flörsheim

Condition: as good as new (ex-display), Year of construction: 2023, One-sided automatic edge banding machine with pre-milling unit, direct glue application to straight workpieces (EVA-PUR Glue pot with run-out function/optional), 2-motor HF-cut-off saw station, HF-top and bottom Multiprofile milling unit, 2-motor corner rounding unit, chain feed, motorized beam pressure with encoder and ball-bearing double roller top pressure, extendable work piece support, signal lamp for work piece sequence, synchronization of working units by encoder as well as L-Motion control (18-axis). For ABS, PVC, melamine and strong wood veneer roll material as well as fixed lengths from 0.4 – 3.0/5.0 mm and of 10 – 60 mm work piece thickness. Cjdpfxef Tdwco Ai Rehd →Automatic edge feeding for roller material over turntable D = 800 mm. →Longer infeed lineal (650 mm) →Pre-milling units :Two reverse, operating-controlled pre-milling units with diamond charged helical joining millers provide a neat and tear-free premilling of the work pieces before the gluing of the edge material. →Glue application directly to workpieces: Teflon-coated glue pot with a capacity of 1,5 kg, leak proof with glue supply from below (excess glue automatically flows back into the glue pot). Glue roller allows exact dosage of glue. Separate glue roller temperature adjustment. Electronic temperature control with automatic stand-by function (reduces probability that the glue burns if the machine is not used for a longer periods and is still turned on). Optional: EVA/PUR glue pot with run out / cleaning function for quick change of glue →Pneumatically operated cut-off knife from roll material up to 3mm edge thickness. →Automatic feeding magazin (70mm magazin capacity) with spiked roller for solid wood. →Pressure unit consisting of one driven pressure roller synchronized with glue spreading roller and two of smaller diameter, conical, one positive and one negative pressure roller with pneumatic tension for a nearly invisible joint of the edge material with the work piece, program-controlled setting for edge thickness via L-Motion Motor →High-frequency cut-off saw equipped with 2 HF motors 0.55 kW, 12,000 rpm , 2 saw blades and high-precision linear guides ensure a clean and precise saw cut, with extraction hoods. Pneumatically tilting from the screen →High-frequency top and buttom milling station, 2 powerful 0.55 kW high-frequency motors with Multifunctional tool (straight + 3 different radius), horizontal and vertical scanning of the work piece; 3 L-Motion motors each for positioning of the horizontal copy shoes, positioning of the vertical copy shoe and positioning of the multifunctional tool →Corner rounding unit : Automatic processing of corner edges up to 3 mm edge thickness. Equipped with 2 high frequency motor 0, 27 kW, selectable on operating panel. One side (front or back edge) or both side corner rounding unit. 2 L-Motion motors each for positioning of the horizontal copy shoes and positioning of the tool. →Rotatable control panel with 10“ color touch screen controls glue temperature settings, automatic temperature reduction for stand-by function of the machine, switching on and off of aggregates and error diagnosis, the motorized beam pressure, extensive program memory and fully automatic operation of the processing units via L-Motion Motors →Mulitprofile Radius scraper unit : With a slight draw cut eventual radius milling traces are removed to provide a perfect finish. It is equipped with a multiprofile t

Condition: used, Year of construction: 2007, machine/vehicle number: AH/004965, The STEFANI Solution 5400 is a single-sided industrial edge banding machine designed for medium and large production facilities. The SOLUTION model range was conceived as a flexible solution for both stand-alone workstations and integration into automated production lines. SALE ON COMMISSION. Codpfx Aisynb Nne Rehd

Condition: used, Year of construction: 2002, Machine length: 6240 mm Weight: 2400 kg Power consumption: 14 kW Extraction diameter: 120 / 140 mm Csdpfx Aevvkfwsi Rehd Storage location: Nattheim

Condition: used, Holz Her Sprint 1312 FÜ + PU Heavy-duty design – edge thickness 0.4 - 12 mm PLC screen control Pre-milling unit for application before the gluing section Fully automatic edge magazine for roll and strip material Glue application station for cartridges + PU bonding automatic tracing nozzle Workpiece height 6-55 mm Csdpfx Aex Eilqei Rehd End trimming unit for roll and strip material up to 12 mm edge thickness with adjustment from 0-10° angle of the trimming saws Milling unit, flush milling up to 12 mm, radius milling – bevel milling - 15° motorised - 4 axes Scraper unit for bevels and radii with 2 pneumatically operated scraper holders pneumatic infeed and outfeed Flat scraper unit – finishing Spray device – PU Machine in TOP CONDITION Available from stock Lieboch

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 0x0x0 mm Weight 8 kg Total power requirement 0,9 kw Codpfx Aijv A E Iye Rehd

Condition: new, Year of construction: 2025, functionality: fully functional, power: 6.5 kW (8.84 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, edge thickness (max.): 3 mm, height adjustment type: mechanical, compressed air connection: 6 bar, plate length: 1,200 mm, product height (max.): 3 mm, tank capacity: 3 l, warranty duration: 12 months, DANIBRUM AC CONTUR 2 – Edge Banding Machine for Curved, Round, and Irregular Panels The DANIBRUM AC Contur 2 is the ideal solution for precision edge banding on panels with non-standard shapes — from oval, round, and rectangular parts to undefined curved geometries. Its operational flexibility allows edge application on 90° angles as well as open and closed arcs, thanks to an advanced mechanical feed system and adjustable profiling setup. A key advantage of this machine is its high-precision edge trimming, enabled by a laser sensor that perfectly synchronizes the edge tape ends, ensuring flawless joints with a tolerance of just ±0.3 mm. Operation is intuitive through a touch-screen interface that allows fast adjustment of all working parameters. The system features a vacuum-supported mobile arm, extendable up to 2250 mm, providing reliable and stable support for the workpiece during processing. For safe and efficient use, the machine is equipped with a foot pedal control system, while the adjustable feed speed enables edge banding at 0 to 30 cm/s and longitudinal profiling at 0 to 24 cm/s. Optimized for Complex Workpieces This machine is designed to handle: Edge tape thickness: 0.5 – 3 mm Panel thickness: 12 – 60 mm Minimum working radius: 20 mm Compatible with various panel formats: Round pieces up to Ø2400 mm Rectangular panels: 1200 x 2400 mm L-shaped panels: 1400 x 1600 mm Equipped with high-speed longitudinal profiling cutters (24,000 rpm), it guarantees a high-quality finish even on complex contours. The AC Contur series includes multiple models, such as AC Contur 2 and AC Contur 3, the latter featuring two extendable arms for increased productivity. Technical Specifications Csdowg E Hvepfx Ai Rshd Edge tape thickness: 0.5 – 3 mm Minimum working radius: 20 mm Panel thickness: 12 – 60 mm Material dimensions: Round: Ø2400 mm Rectangular: 1200 x 2400 mm L-shape: 1400 x 1600 mm Cutter speed (longitudinal profiling): 24,000 rpm Feed speed: Edge banding: 0 – 30 cm/s Profiling: 0 – 24 cm/s Edge tape joint accuracy: ±0.3 mm Compressed air pressure: 0.6 – 0.8 Mpa Working temperature: 110 – 210°C Adhesive tank capacity: 2.6 liters Arm extension length: 2250 mm Installed power: 6.5 kW Power supply: 400 V – 3 Phase – 50 Hz Weight: 430 kg Overall dimensions: 1870 x 1400 x 1530 mm

Condition: excellent (used), Year of construction: 2018, Chassis for edge banding machines Was mounted on Homag Edgeteq S-200, KDF 1130 FC (1100kg). Will certainly also fit other machines, such as Brandt (minor modifications may be necessary) Length of U-section: approx. 1130mm Overall height incl. castors: approx. 150mm 4 sturdy steel swivel castors with grease fittings 2 locking brakes 2 leveling plates for height adjustment Chjdpfx Aiew S Dmds Rod Machine can be demonstrated on site by appointment. We only offer machines that are ready for demonstration in our warehouse, see "more offers from this seller".

Condition: new, Year of construction: 2026, The Hebrock F 5 If you want maximum performance, the Hebrock F 5 is the solution for edgebanding in demanding workshops. The F 5 guarantees edge processing in all steps, as it is equipped with all the components you need for your requirements: jointing cutter, miter saw, milling unit, radius pull blade, corner cutter, surface pull blade, and finishing station. For even more flexibility on the way to the perfect finish, the F 5 can optionally be equipped with a practical multi-radius pull blade. Chjdpfx Aolht Hwoi Red Maximum edge thickness: 3 mm Maximum workpiece thickness: 50 mm Ready for operation in 3.5 minutes Equipment: Hebrock F5 Next - 10 m/min Edgebanding machine F5 Next With PLC control (including touchscreen) and with hot melt adhesive application to the workpiece for edge material up to 3 mm; jointing cutter (including diamond tool) up to 2 mm cutting depth, maintenance-free glue tank with interchangeable tank preparation including glue dispensing device, HF miter saw station (approx. 12,000 rpm), HF milling station (approx. 12,000 rpm) with separate pneumatic milling adjustment and interchangeable plate cutter (combination design), corner rounding cutter, radius pull blade, surface pull blade (including pneumatic feed), finishing station, robust chain drive, ball-bearing double roller pressure, viewing window from the back of the machine, pull-out workpiece support, feed rate approx. 10 m/min. Hebrock F5 F5/08/4 Quick-change preparation for corner cutter F5/08/5 additional interchangeable motor for corner cutter with tool set F5/09/4 Multi-radius pull blade (R1/R2) F5/10 Chassis F5/14 additional interchangeable tank F5/24/1 Spray device for release agent F5/24/2 Spray device for cleaning agent F5/25 Spray device for edge F5/27 Nesting for cutter and radius pull blade F6/28 Spray texture finish F5/30 Pneumatic 3-point adjustment (radius, bevel, flush milling) F5/31 Jointing up to 50 mm F5/32 LED lighting Location: In stock, 54634 Bitburg - available immediately -

Condition: new, - New -Description:- Top equipment for high productivity in a small space!- Intuitive operation with the eye-S control and 10"large touch screen: HMI Maestro Active Edge,Graphic display of all machining units and theiroperating status, Graphic simulation of machining operations,Control of all machining units, Regulationof glue tank temperature, Assistance functionsfor setting up the machine according to the machining program,Fault diagnosis for quick elimination of simple errors,Statistics on machining parameters, USB connection,Preparation for network connection, Preparation for Industry 4.0with data transmission protocol API REST- Excellent accessibility to the working aggregatesthanks to the large hood that ensures protection and noise reduction- Monoblock construction made of steel ensures high stabilityand rigidity of the machine- Automatic aggregate positioning when changingthe panel thickness- Automatic application of the strip edges with edge magazine(me 35 t s): The strip edges of solid wood areautomatically loaded and synchronized with the panel guide- Panel feed is made by feed chain with rubber glides- Extendable workpiece support- Adjustment of the infeed ruler via spacer platesTechnical data:Dimensions and weightsLength approx. 3314 mmHeight approx. 1300 mmWidth/depth approx. 1085 mmWeight approx. 545 kgflush radius milling unitflush radius milling unit input power 2 x 0,35 kWflush radius milling unit cutter speed 12000 min¯¹flush radius milling unit cutter diameter HM 55.3 mmFlush radius milling unit suction port diameter 2 x 60 mmElectrical dataSupply voltage 400 VMains frequency 50 HzGlue unitGlue tank input power 0,25 kWGlue tank suction port diameter 60 mmGlue tank working temperature 190 °CGlue tank filling quantity 0.8 kgPneumatic connectionOperating pressure 6.5 barAir consumption 470 l/minFeed rateFeed input power 5 kWFeed speed 7 m/minEdgesEdge thickness roll material 0.4 - 3.0 mmEdge thickness strip material - 5.0 mmPre-milling unitPre-milling unit input power 3 kWPre-milling unit diamond cutter diameter 80 mmPre-milling unit material removal ,5 / 2 mmpre-milling unit cutter speed 7200 min¯¹pre-milling unit cutter height 56 mmpre-milling unit exhaust diameter 2 x 80 mmscraper unitradius scraper 2 mmbuffing unitbuffing unit input power 2 x 0,14 kWbuffing unit speed 2800 min¯¹workpieceworkpiece thickness 8 - 50 mmworkpiece width min. 110 mmWorkpiece length min. 120 . 5507235 Chjdpfx Ajvwfmlji Rod

Condition: used, Year of construction: 2003, Single-sided edge trimming and gluing machine Manufacturer: IMA Type: AVM/K/I/G80/822/S3R3L20 Year of manufacture: 2003 For milling, edge gluing, and finishing for a standard groove - only for pre-shaped/pre-grooved doors and square-edged doors Left-hand machine (fixed stop on the left). Complete processing in 3 passes 1st pass: Processing of the top surface of the door (transverse processing) 2nd pass: Door long edge 3rd pass: Door long edge During the 2nd and 3rd passes, the protruding transverse edge from the 1st pass is milled off by using a co-rotating/counter-rotating milling process. Double groove gluing is only possible through modifications to the machine and subsequent manual finishing of the edge. Max. door thickness: - Straight edge: approx. 70 mm - Groove gluing: approx. 60 mm Stable machine frame as a support for aggregates and housing for electrical installation. Drive for feed speeds of approx. 5-25 m/min., mechanically infinitely adjustable. (not to be confused with processing speed) Continuous, plastic-coated strip-type conveyor chain, approx. 80 mm wide, with automatic central lubrication. Manually height-adjustable top pressure with a V-belt 80 mm wide and spring-loaded, ball-bearing guide rollers. Machine length approx. 10,900 mm Infeed table at the machine inlet. 1 horizontal, manually adjustable, unheated stop bar 1 joiner milling unit controllable, not swiveling, without sensing with 2 motors, each 3 kW Gluing unit for optional operation of straight edge or softforming gluing, by changing the glue application. Edge material: - Strips: up to 1.3 mm - Roll material: 0.4-3 mm - Solid wood strips: 6 mm Strip length max.: 2550 mm Strip height: 14-80 mm (depending on glue application) with: - Side adjustment by hand for the pneumatically controlled glue application. - Height adjustment by hand -15mm downwards and up to +10mm upwards. 1 bell for the main pressure roller, manually adjustable 1 glue application 0.8L, max. edge height 70mm, straight edge with pneumatic quick-release, Chem-Coat coated, electronic temperature control 1 hot melt glue application 0.8L with quick-release, up to max. 80 mm high edge material, soft edge, Chem-Coat coated, with temperature control and control unit Chedpfozuykvsx Ai Rjd for the strip coating 1 automatic Quickmelt hot melt glue feeder with a heating power of 5.0 kW 1 2-fold magazine only for edge material up to 3.0 mm thick, can be manually attached to the single-roll magazine 1 groove forming pressing unit for pressing the edge material into the groove with: - an activation unit 15 kW for re-activating the edge material for groove forming - a pneumatically controlled forming shoe for the underlapping edge - a pneumatically controlled forming shoe for the entire groove - additional post-pressing rollers for the edge areas in the groove - an electro-pneumatic lateral retraction device for the entire pressing unit 1 horizontal adjustment with mechanical digital display 1 trimming unit for 2 motors mounted on the top pressure for trimming the front and rear edge/strip overhang, for trimming cuts flush or with a bevel. 1 milling unit for 2 motors with height sensing, side sensing, for pre-milling from below and above with 2 motors 1kW, 400V, 200Hz, 12,000 RPM, 30° swiveling 1 milling unit for 2 motors with height sensing, side sensing, for fine milling from below and above with 2 motors 660W, 400V, 200Hz, 12,000 RPM, 30° swiveling Note: The technical data and descriptions are copies of the original order

Condition: reconditioned (used), Double-side Sizing-Milling & Edge Banding - First (1st) machine in a line Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Panels thickness (min/max) mm 8 / 45 Working width (min/max) mm 236 / 1300 Numerical Control /Software ICOS Open Adjustable feeding speed (m/min ) 10 / 50 Without Transmission bar (Master & Slave system) Safety and sound-proof enclosures/cabins Chsdpfx Aijdh Tfgj Rsd SIZING PART (for each side): Spraying unit (Anti-sticking liquid) Milling Unit (vertical Joint Trimmers) 08. 0555 max. 3° (2 x 1 kW) Free space EDGE-BANDING PART (for each side): Glueing Unit (Hot Melt Glue + Quick Melt system) 04.1570 Band Pressure zone Edge coils supporting unit (reels N°) 6 Rough Trimming unit 08. 0555 (2 x 1 kW) max. 3° Fine Trimming unit 08. 055 (2 x 0,66 kW) 30° + 30 m/min Glue scraping unit 08.517 Spraying Unit (for polishing liquid) Buffing unit 08.617-2 (2 x 0,18 kW) Free space

Condition: used, Year of construction: 2007, machine/vehicle number: Werksüberarbeitungsnummer: WÜA1363DK-F7560, Used Machine GM020.0068 AKV 3003 DK - F Year of manufacture: 2007 Specification: 3 mm 1st milling station: Combination Surface pull scraper with extraction Chassis Pneumatic milling adjustment Chsdpfx Aijw Nih Io Rod Limit switch lever, 7.5° inclination

Condition: new, Year of construction: 2025, Edge banding machine F5 with PLC control (including 15" touchscreen), hot melt adhesive application to the workpiece for edge banding material up to 3 mm: Joint milling cutter (including DIA tool) up to 2 mm cutting depth, maintenance-free glue pot with interchangeable pot preparation, including adhesive dispensing device, HF milling station with pneumatic milling adjustment, including corner rounding milling cutter, radius trimming knife, edge trimming knife (including pneumatic extraction device), finishing station Joint head Whispercut Combination milling head Radius milling cutter R=2mm Radius corner milling cutter R=2mm Quick-change preparation for corner milling cutter Radius change motor R=1mm Multi-radius trimming knife R1/R2 Chassis Spray device for release agent (PUR) Spray device for cleaning agent (PUR) pneumatic 3-point adjustment LED lighting INCLUDING 2nd interchangeable glue pot max. edge thickness 3mm Workpiece thickness 8-50mm min. workpiece length approx. 160mm Feed speed 10m/min Ready for operation in approx. 3.5 min Dimensions approx. 4300x1300x1400mm LxWxH Csdpfx Aeh Hl Ayei Rehd Weight approx. 900kg Extraction port 1 x 140mm

Condition: used, Year of construction: 2003, Used Machine Year of Manufacture: 2003 Features and Technical Specifications: - MAGELIS control system - For EVA-based hot-melt adhesive - Joining: 2x1.5 kW, u=12,000, 200 Hz - Trimming: 2x0.2 kW, automatic swivel 0°/3°, 2 carbide-tipped saw blades 140 mm - Flush milling: 2.07 kW, with WPL HF 70 heads, diameter 70 mm - Radius milling: R2 - Radius scraper - Surface scraper Csdezk Nt Eopfx Ai Rohd - Top glue tank - Workpiece dimensions: - Minimum width: 70 mm - Thickness: 8–42 mm - Minimum length: 150 mm - Edge thickness: 0.2–6 mm - Feed rate: 12 m/min - Dust extraction connection: 160 mm Dimensions: 4,500 x 1,250 x 1,300 mm Weight: 1,650 kg

Condition: new, Year of construction: 2026, Hebrock F 4 For the complete processing of your panels For those who don’t want to compromise. With the F 4, we offer you a model that allows you to produce completely finished edges on a machine length of only 4 meters. The F 4 is not only space-saving but also extremely attractive in terms of price-performance ratio. Max. edge thickness: 3 mm Min/Max. workpiece thickness: 8 – 50 mm Min. workpiece length: approx. 160 mm Feed speed: approx. 7 m/min Ready for operation: approx. 3.5 min Max. power consumption: approx. 7.4 kW Electrical connection: 400 V – 3 phases – 50 Hz Codpfx Aishqadcj Rehd Work table height: approx. 900 mm Machine dimensions: approx. 4050 x 1300 x 1400 mm (L x W x H) Weight: approx. 820 kg Extraction nozzle: Ø 1 x 140 mm PLC control with 10″ touchscreen Top-mounted rapid heating glue tank (maintenance-free) Support plate for edge material Automatic central lubrication (miter saw, corner router) Optical display for workpiece sequence Outrigger (extendable to the front) Quick-change unit preparation, including glue change device for PUR processing Surface scraping blade with dual contact Pneumatic roller capping (scissors-type design, Hebrock system) Double roller pressure (ball-bearing mounted) Transport chain with permanently screwed-on special chain plates Edge router Routing unit Miter saw Corner router Accessories: F4/09 Radius scraping blade (incl. pneumatic lift) F4/09/4 Multi radius scraping blade (R1/R2) F4/30 Pneumatic 3-point adjustment Location: In stock, 54634 Bitburg - available on short notice -

Condition: new, Year of construction: 2026, Machine includes: Pre-milling, pre-heating, pre-melting, pressing, fine trimming, end cutting, corner rounding, cutter scraping, flat scraping, buffing Codpfx Aiexd Ubbo Rehd Heavy duty machine body and most mechanical machine parts are proceeded by advanced CNC machines for higher stability and longer service life without deforming; Merges numerous functions in one machine, including pre-milling, pre-heating, pre-melt gluing system, snipping, end trimming, fine trimming with servo, corner trimming, scraping with servo, surface scraping and buffing, sprayers, edge banding work can be done in one process. Intelligent PC control, infeed fence, tape pressing rollers, fine trimming and scraping are servo adjust. Corner rounding pneumatic adjust. Machine Speed 16/20/24m/min; Nesting kit design, pre-drilled nesting hole friendly Fine trimming and Corner rounding by HSK25

Condition: new, Year of construction: 2025, HEBROCK Edge Bander F2 next with SPS control system (incl. touchscreen) and hot-melt glue application to the workpiece for edge material up to 3 mm: pre-milling unit (incl. DIA tool) up to 2 mm milling depth, maintenance-free glue pot with preparation for interchangeable tank incl. glue discharge device, HF cross-cut saw station (approx. 12,000 rpm), HF milling station (approx. 12,000 rpm) with separate pneumatic milling adjustment and indexable insert cutter head (combi version), robust chain drive, double roller upper pressure with ball bearings, inspection window on the rear of the machine, extendable workpiece support, feed rate approx. 10 m/min. Including: F2/500/10 Whispercut pre-milling head F2/500/20 Combination milling head Chjdpfxjwmdbre Ai Rjd F2/500/2 Radius cutter R=2mm F2/12 Surface scraper (incl. pneumatic lift)

Condition: refurbished (used), Year of construction: 2016, machine/vehicle number: 3074, functionality: fully functional, input voltage: 400 V, input current: 32 A, input frequency: 50 Hz, type of input current: three-phase, workpiece height (max.): 60 mm, edge thickness (max.): 3 mm, height adjustment type: mechanical, total height: 1,618 mm, total length: 4,984 mm, total width: 1,425 mm, overall weight: 1,400 kg, year of last overhaul: 2025, Equipment: CE marking, Due to the acquisition of a new machine, our reliable edge banding machine, purchased new in 2016, is now for sale. The machine has operated in a joinery workshop with 8 employees. It underwent a complete overhaul in January 2025. New radius scrapers, new milling tools, and new polishing wheels were installed. The pre-milling unit has been re-sharpened. The glue roller’s clutch has been replaced. The glue pot was completely refurbished and cleaned. The machine is suitable for both EVA granulate (e.g., Henkel Dorus KS351) and PUR adhesives. Chjdpfxjzhrdus Ai Rjd The degree of pre-milling, the edge material thickness, and the position of the lower and upper milling tools can be conveniently adjusted from outside the machine housing via manual handwheels. The control system allows custom edge banding programs to be saved. The machine automatically and pneumatically switches between 0.4 mm and 2.0 mm edge banding via program. Main specifications: - Power: 13.8 kW / 32 A / 400 V - Compressed air: 7 bar (100–150 l/min) - Touchscreen - Saved edge banding programs - Feed speed: 10 m/min - Edge material thickness, in rolls: 0.5–3.0 mm - Workpiece thickness: 8–60 mm (banding 60 mm thick materials possible) - Minimum workpiece width: 70 mm - Minimum workpiece length: 180 mm (for end trimming saw) / 220 mm (for corner rounding) - Processing units: - Diamond pre-milling (12,000 rpm) - Release agent tank/nozzle - Gluing station - End trimming saw - Milling unit R2 - Radius scraper R2 - Corner rounding unit - Cleaning agent tank/nozzle - Flat scraper - Polishing wheel Price does not include VAT.

Condition: refurbished (used), SINGLE-SIDE SIZING & EDGE BANDING MACHINE (Left side machine) Edges (tape) thickness in rolls (min/max) mm 0,3 - 3 Edges thickness in stips / lippings (min/max) mm 1 ALU Panels thickness (min/max) mm 6 - 55 Chsdocr T N Dopfx Ai Red Numerical Control /Software IMATRONIC 121 /01 Adjustable feeding speed (m/min ) 6 - 30 SIZING PART : Pre-milling Unit (vertical joint trimmers) adjustable by N.C. (2 x Kw 4,5) 08.376 Spraying unit (Anti-sticking liquid) EDGE-BANDING PART : Lamps to heat the workpieces side + Glueing Unit (P.U.R. Glue + Quick Melt unit) 04.1569 Band Pressure zone mm 1000 + Edge coils supporting unit (N. 6 reels) Snipping (end-cutting) unit 08.42 (2 x Kw 0,66) working speed 25 m/min (swivelling 0-25°) Rough Trimming unit 08.0555 (2 x Kw 1) Fine Trimming unit 08.055 (2 x Kw 1) 30° + Spraying Unit (for sliding liquid) Multi-Profile Copying unit 08.348 (fine and contour trimming) adjustment by N.C (2 x Kw 0,66) Profile edge scraping unit (Multi-profile, adjustable by N.C.) 08.516 Glue scraping unit 08.517 (Pneumatic) Spraying Unit (for polishing liquid) Buffing unit 08.614 (2 x Kw 0,25) Milling grooving unit 08.183 (1 x Kw 3) Smoothing unit with spheres 08.53 Chamfer Sanding Unit for straight edges WI (4 x Kw 0,75)

Condition: ready for operation (used), Year of construction: 2016, machine/vehicle number: 0-261-04-6588, functionality: fully functional, power: 21 kW (28.55 HP), workpiece height (max.): 60 mm, feed rate X-axis: 18 m/min, total length: 6,060 mm, overall weight: 2,600 kg, The machine comes with the following configuration: Emulsion spray at both infeed and outfeed Edge pre-heating Pre-milling unit: Tool diameter: 100 mm, Tool height: 63 mm, diamond tool with replaceable knives, motorized adjustment for removal Glue application unit: Glue and hot air application, heated application roller, quick-change feature for the entire unit, automatic position adjustment via motor, 3 pressure rollers, edge feed speed: 14 m/min End trimming unit: Twin-motor unit with automatic tilt up to 15°, THK prism guide Radius milling unit: 2 tools, automatic 2-axis adjustment, automatic overlap adjustment Copying unit: 2 motors, automatic tool position change via servomotor, electromagnetic horizontal movement, vertically hydraulically damped movement Cleaning and polishing unit Automatic return conveyor: Homag TFU 140 Chsdjyu If Nepfx Ai Rjd TECHNICAL DETAILS Workpiece thickness: 8–60 mm Max. feed speed: 18 m/min MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 6,060 x 1,555 x 2,300 mm Weight: 2,600 kg Total connected load: 21 kW Compressed air: 6 bar Air consumption: approx. 350 l/min Extraction: 2,820 m³/h EQUIPMENT Double top pressure for part stability Electronic thickness control Frequency converter for feed Automatic lubrication of feed chain Automatic motor calibration Touch control panel

Condition: used, Year of construction: 2009, HOLZ-HER edge banding machine CONTRIGA 1366 Edge thickness: 0.4-30 mm (depending on equipment) Edge height: 51/66 mm (depending on equipment) Panel thickness: 6-45/60 mm (depending on equipment) Edge types: Rolls and strips Feed speeds: Continuous feed from 12-30 m/min (depending on equipment) With adjustable infeed level in the magazine area (max. adjustment range 30 mm) With height-adjustable magazine plate for changing the lower edge overhang With large magazine plate Ø 820 mm for edge rolls up to Ø 800 mm With transport chain including automatic central lubrication With motor-driven, position-controlled bridge height adjustment With pneumatic locking roller for the shortest workpiece sequence With extendable workpiece support (extension width 1600 mm) With space-saving, pneumatically controlled sliding hoods over the entire machine (Deviations for individual units are possible) with motorized infeed guide with injection oiler for lubricating all joints and bolts (including operating hours counter) with central connection for extraction (2x Ø 200 mm) with integrated chip collection box at the end of the machine (when radius scraper unit is installed) PPC 231 control system - Power PC for efficient setup and changeover - 15" SVGA screen with touchscreen - 128 MB CF memory card - USB connector on board - Ethernet network connection - Keyboard connector on board - Windows-like user interface - all information in plain text and/or graphics - Rotatable and pivoting control panel at eye level - Dust-proof membrane keyboard with softkeys (pushbuttons) - LED display for unit preselection - Program list with program names and numbers - Extensive program memory - Individual selection of the units with the functions as basic setting options for setpoints, route points and tool corrections as well as the fixed route points - Centralized and clear setup processes for units and their axis settings via fine adjustment (depending on the equipment) - Interval display for the shortest workpiece distance - Integrated path control - Path points are controlled generally or program-specifically - Clear and complete recording of all operating data - Service messages in plain text - Diagnostic system - including integrated synchronous bus system for high precision in unit control - Individual administration for up to ten users, including password protection - Online maintenance (optional), data exchange with HOLZ-HER Service - Barcode interface (optional) BASIC MACHINE CONTRIGA 1366 - Belt bridge Options and accessories for the basic machine Spraying device 1856 for the inlet and outlet area For the inlet area: Electronically controlled release agent sprayer with Riepe-LPZ/II release agent For the outlet area: Electronically controlled cleaning agent sprayer with Riepe-LP163/93 cleaning agent (only in conjunction with pre-milling unit 1961 and surface scraper 1964) Joint milling unit Joint milling station 1803 (2x 2.6 kW, 200 Hz, 12000 min-1) With two plunge-controlled milling units 1 unit in up-cutting direction 1 unit in down-cutting direction Plunge path 5 mm With static frequency converter 200 Hz Without milling tool With ProLock screw-in clamp for fast tool changes Tool for 1803 (workpiece height up to 60 mm) Diamond milling cutter PRO UT 2 pieces (front and rear) including protective covers Ø 100-63 - Ø 30 mm, Z = 3 + 3 + 3, 1x left-hand rotation, 1x right-hand rotation Noise-reduced milling cutter with integrated chip guide DFC technology (Leitz syst Cedpfxjvvkfdo Ai Rshd

Condition: new, Year of construction: 2026, functionality: fully functional, power: 3.6 kW (4.89 HP), input voltage: 230 V, type of input current: AC, edge thickness (max.): 3 mm, height adjustment type: mechanical, overall weight: 11 kg, compressed air connection: 6 bar, working height: 65 mm, The perfect zero joint - for laser edgebands / hot-air edgebands / co-extruded edgebands - Up to 65 mm edge height - Up to 3 mm edge thickness - Mobile or stationary use - Tool-free changeover Cedpfxor H Eale Ai Rehd - Up to 3 mm edge thickness - approx. 4 min heating time - 230 V / 50 Hz

Condition: used, Storage location: Sonnefeld Chedjway Dcspfx Ai Rod