Used Fabrik for sale (139)

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Cjdpfxsx A U Nco Addehf Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: used, Year of construction: 1978, Technical details: table surface area: 1970 x 400 mm distance between table/spindle: min./max. 150 / 250 mm rapid traverse: 1 / 2 m/min revolution per minute: Frässpindel: 112 ... 1400 / 12 step U/min milling spindle taper: DIN 2019 = Nr. 40 (SK40) Chedpfxju Ndhis Addjf axial adjustment: manuell = 150 mm quill feed: 0,012 / 0,025 / 0,05 mm/U feed range - horizontal: Frässchlitten: 8...100 / 12 step mm/min total power requirement: ca. 8,4 (10,5 kVA) kW machine weight approx.: 3000 kg dimension machine xH: 3,05 x 2,7 x 2,0 m wedge-groove milling machine Application: Milling of straight and helical grooves. Multiple groove milling with automatic program sequence. Further features: - distance spindle axis / lower edge counterholder: 55 mm - axial movement of the counter bearing sleeve 50 mm - milling carriage movement horizontal 1000 mm (automatic + manual by hand) and vertical 100 mm by hand + max. 5mm automatic/hydraulic Equipment: - chip container 470x300x300mm - 2x oil collecting basins (3200x1500x70 and 3200x800x60mm) - some accessories/tools *

Condition: good (used), Power: 16 KVA Chedpehc Syzefx Addof

Condition: used, Year of construction: 2017, functionality: fully functional, CHIP CONVEYOR 1200MM Hinged belt conveyor with discharge height approx. 1200mm, suitable for: • Long steel chips • Chip nests • Wool chips For dry and wet machining Free loading Cjdpfxox A Dn Uj Addehf Available immediately

Condition: as good as new (ex-display), Semiconductor protection Make Klöckner Moeller Chedsmxi U Sopfx Addef Type DIL SM 16 V-k 400 Volt 16 A 7,5 kw unused from stock

Condition: used, Cutting force of 10 tons Sheet thickness up to 3.15 mm Maximum material strength: 50 kp/mm² Chsdpoxxz Haofx Addsf

Year of construction: 1950, condition: excellent (used), Article number: MA 994 Manufacturer: VEB Waggonfabrik Gotha / Lev - VEB Lokomotivbau Hennings village Type: BZ 57 - two leadership Year: 1957 Length [m]: 10.9 bulkhead / total length 12 m Width [m]: 2.2 Height [m]: 3.115 Weight (kg]: 8400) Seats: 22 Standing passengers: 83 Axles: 2 Doors: 4 doors Cjdpsdwd Dmjfx Addshf Other: documentation

Condition: used, Year of construction: 1999, Technical details: x-travel: 690 mm y-travel: 400 mm z-travel: 550 mm B-axis (table): 360° mm control: Siemens 840 D number of spindle speeds: max. 15 000 U/min tool clamping: System nach DIN 69893 tool taper: HSK-A63 tool changer magazine: chain magazine: 12 places Stück traversing speed: x/y/z Axis: 40 total power requirement: 195 kW weight of the machine ca.: 13,0 t Traveling Column Milling Machine Cjdpfx Adou Idl Ssdohf - the tool changing unit consist of 3 -NC axis and 1 NC- rotary table axis - ATC ( with magazine) - rotary table Type SKH-NC 4/029, diameter=460mm , table surface plate Ø 500 x20mm, revolution per minute max. 22 rpm - control panel SIEMENS - Spindel-Typ: DRF-WE-255-N-W-15-30, 15000 U/min., Spindelleistung = 30 kW - chip conveyor Make Knoll type 400K-3/280, ejection height 1150mm - cooling system for spindle make SCHIMBKE Type DK 80V, 3,36 kW i.D. *

Condition: good (used), Year of construction: 2011, functionality: fully functional, machine/vehicle number: 6860 0007, Please let us know your quote. Sale only within the European Union (EU), including Switzerland, Turkey, and Great Britain ----- Scope of delivery: Machine, loading system, conveyor belt, workpiece carrier Machine specifications: 5-axis grinding center including oval feed belt and loading gantry 12-station tool changer with HSK 63 Max. X-axis travel: 500 mm Chedpfx Adovbgiisdjf Max. Y-axis travel: 650 mm Max. Z-axis travel: 650 mm Table size: 500 x 650 mm Cut-off detection Nordmann dressing spindle Oil supply via central factory supply

Year of construction: 2025, condition: new, functionality: fully functional, A total of 450 unused Big Bags are available for sale. Each pallet contains 150 units. Delivery on pallet is possible for an additional freight charge. Quality and specifications: Big Bags, form-stable, uncoated, SWL (safe working load) 1250 kg, SF 6:1, 200 g/m², top open, bottom closed, 4 lifting loops, each 25 cm in length, overhang, UV-stabilized on EWP approx. (100x120x100 LxWxH) Dimensions: approx. 101x101x200 cm (external dimensions) No individual bag sales—only by full pallet! The above price refers to one pallet (150 units). Codexr Dm Aepfx Addehf

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, functionality: fully functional, pressing force: 70 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 500 kg, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a Chodsu Thbxepfx Addof bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Drive power 4.0 kW Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Year of construction 2023 Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Clamp holder make Comet FG IIII (28396) Chedpfx Adomk E Uiodsf for Comet threaded steel FG IIII TR 12

Condition: ready for operation (used), C-frame Press, Hydraulic Press, PYE Press 3t, Used Machine Chodpfx Adow Hc H Hsdef Manufacturer: VEB Wema Type: PYTE 3.15 Overall dimensions: 500 x 730 x 1170 mm Pressing force: 3.15 tons Stroke: 280 mm Table size: 280 x 280 mm Electrical data: 380 V; 1.5 kW; 4 A

Condition: used, Year of construction: 1977, Technical details: honing diameter: 125 mm stroke: 500 mm throat: - mm grinding spindle speed: 26-1200 (12Steps) U/min honing diameter: 30 (min.) mm honing diameter: 165 (max.) mm table adjustment:: 800/150 (max.) mm table surface area: 500 x 1000 cm total power requirement: 4,22 kW Weight approx.: 0,15 t dimension machine xH: 1,30 x 1,20 x 2,70 m Csdew Rv Taopfx Addehf There is a movable table that moves lengthwise and crosswise. *

Condition: good (used), Year of construction: 1980, functionality: fully functional, STC-Ref:G-791-0121 Karl Mayer-Web-Wirk machines ,Year: 1980 format width: 12 Zoll, 4,06 mtr equipped: - für Schattennetze - material width max. 160 Zoll, 4,06 mtrs. - type: R 4 n1 M-FSM - grammature 70 g/qm - 180 g/qm - many spare parts included - GANG753 --> available: 11/2024 Chsdpfst Rhykjx Addsf

Year of construction: 2017, condition: ready for operation (used), Belt length: 2900 mm belt width: 360 mm Belt speed infinitely variable drive motor Chsdpfx Adsdzx E Usdsf table height adjustable by: +/- 500 mm space requirement: 2000 x 600 x 650/700 mm

Year of construction: 1979, operating hours: 216 h, condition: reconditioned (used), functionality: fully functional, Twin-screw extruder, parallel Manufacturer: Hans Weber Maschinenfabrik GmbH Type: DS 85 Year of manufacture: 1979/2022 Machine no.: 85-399 Screw geometry: for PVC-hard profiles Screw diameter: 2 x 85 mm Screw length: 17 x D Screw speed: max. 30 rpm Screw torque: 10000 Nm Motor power: 3.3 - 25.0 kW Drive motor: commutator motor Elektra Faurndau Cylinder heating/cooling zones: 4/2 (air cooling with fan) Tool heating zones: 8 Temperature control: 12 x digital temperature controllers (PMA KS40) Accessories: Melt pressure sensor and melt temperature sensor Connected load: approx. 60 kW (without tool) Extrusion height: 1100 mm Output capacity: approx. 150 - 180 kg/h for PVC-hard profiles Accessories: Material hopper and connection flange Accessories: Vacuum pump (1.1 kW) incl. material separator Chjdpfxjxlcfkj Addef Dimensions: 4500 x 1200 x 2100 mm (LxWxH), incl. material hopper Weight: approx. 4000 kg Note: The electrical control cabinet was completely renewed approx. 3 years ago. Since then, the extruder has only been in operation for 216 hours. Condition: The extruder was repainted (light gray, RAL 7035) and checked for function.

Condition: as good as new (ex-display), Year of construction: 2015, functionality: fully functional, machine/vehicle number: 15194, tank capacity: 2,000 l, Laska mixer in very good condition… Cjdpfx Aoxbbkdjddehf

Condition: refurbished (used), C11 MKL Cross-Cut Optimization Line, offered by Wood Expert Industry, is a state-of-the-art technological solution designed specifically for industrial wood processing and operational workflow optimization in woodworking facilities. All equipment comprising the processing line is manufactured by Paul Germany and was completely overhauled in July 2025 with zero operating hours. Paul C11 MKL Lumber Optimization Line Components Cedew Emf Rjpfx Addohf - 9.0 m / 230 mm Inclined Conveyor Belt Ideal for the automatic and efficient handling of wood pieces towards the processing area, equipped with a guided belt and robust clamping parts for stable transport. - Measuring Station with Luminescent Scanner and Photocell Allows precise identification of the start and end of workpieces, featuring dedicated lower rollers for high-accuracy measurements. - Pressure Roller Unit Ensures correct alignment and pressing of pieces between 250 and 4200 mm, with manual adjustment available according to the material thickness. - Reinforced Marking Rails, Left and Right Automatically pre-marks cutting positions for increased efficiency and accuracy in subsequent processing. - C11 MKL Optimizer – CNC Cross-Cut Saw Station Includes a robust welded steel frame, 500 mm TCT blade, 5.5 kW servo-driven motor, variable speed, and an advanced feeding system with lower/upper rollers for precise piece guidance. Electric adjustment of the upper rollers allows automatic adaptation to wood thickness. The system features automatic waste extraction, extraction ports, CE safety compliance, and advanced cutting quality options (blade with 132 conical teeth). - Waste Extraction System Comprises an 11.5 m / 230 mm conveyor belt and ascending waste belt (3.0 m / 500 mm with collection hopper), optimizing material flow and disposal of residues. - Length Sorting System With pneumatic ejectors and basic sorting equipment, this facilitates automatic organization and discharge of pieces to two outfeed positions, increasing line productivity. - Maxi8 Premium Operator Terminal and Optimization Software 17” touchscreen terminal, dust-protected, remote diagnostics, Linux-based, with dedicated optimization software (up to 60 cutting lists, 9 grading options, 400 preset lengths/list), advanced statistics, network integration capability. Includes data import/export options via USB. - Control and Automation Equipment Standardized electric cabinets, control panels, complete installation and wiring performed with high-quality components for intensive industrial use. Benefits of integrating this line: - Fully automated cross-cutting process, significantly reducing human error. - Increased efficiency and yield through cutting list optimization and automatic length sorting. - Adaptability to various thicknesses and sizes of workpieces. - Advanced digital control and remote diagnostics for quick interventions. - High reliability, reduced maintenance costs, and adherence to strict CE safety standards. This optimization line can be customized for different types of wood processing facilities, ensuring efficient operation tailored to every client’s requirements.

Condition: used, Year of construction: 2004, Technical details: x-travel: 1500 mm y-travel: 1000 mm z-travel: 1000 mm control for program: TNC 530 spindle hours: noch nicht bekannt h milling head speed: 1: 30 bis 930 und 2: 930 bis 4000 / steples U/min tool taper: horiz./vertical: SK 50 (DIN 69871/Din 69872 Form A) max. torque on the spindle: 1000 Nm spindle head swivable left - right: 90 ° feed: 1 - 6000 mm/min feed power: 30 kN kN rapid traverse: 15 m/min Number of tools: 1 St. table clamping surface LxW: 1600 x 800 mm table load: 40 kN kN voltage: 400 V / 50 HZ V total power requirement: 42 kW Weight approx.: 15,2 t dimension machine xH: 3,1 x 4,7 x 2,6 m dimensions: Kühlfilter: 1,9 x 1,6 x 1,4 mm space requirements approx. LxWxH: ca. 38,5 m² m² compressed air: 6,3 bar Applications: Chjdeu Nc Rispfx Addof Milling, drilling; tapping, boring. with direct coded length measuring systems the guideways of the 3 axes are on flat guideways CTS and external cooling Milling head position controlled +/-90° milling spindle nominal drive power 22 kW with integrated hydraulic power unit up to 100bar operating pressure with coolant unit with filtration, with high pressure pump 60 bar (internal cooling), nominal delivery 20 l/min. and low pressure pump 4 bar (external cooling) as well as spray gun Hinged belt chip conveyor DGS, type SSF 600 P50 Accessories: Measuring probe SK40 Reference tool SK40 Milling head SEMPUCO *

Condition: excellent (used), Year of construction: 2018, Converting Line GM 330 FB-D (Hot stamping + Screen printing) Year of manufacture: 2018 Manufacturer: Grafisk Maskinfabrik Maximum web width: 350 mm Minimum web width: 50 mm Maximum unwind diameter: 700 mm Maximum rewind diameter: 600 mm - Vetaphone Corona Treater - BST Web Guiding System Hot Foil Stamping Unit (Flatbed) Speed: 6,000 impressions/h or 10-15 m/min Web width: 110 mm - 330 mm Dual foil unwind and rewind with 250 mm diameter Substrates: 50–500 µm Plate thickness: 5-10 mm (7 mm standard) Stamping pressure: 30 tons Foil feed in both transverse and longitudinal direction (rotatable turret) Temperature range: 80° - 130° C Heating time approx. 20 min. Screen Printing Unit Speed: 4,000 cycles/h or 5-15 m/min Web width: 110 mm - 330 mm Frame size: 660 mm x 500 mm Frame type: 30 mm x 30 mm aluminum frame Csdjw I T Ucspfx Addehf Printing area: 330 mm (length) x 330 mm (width)

Condition: ready for operation (used), functionality: fully functional, Skinning machine MAJA BXM 754 Cutting speed: 22.1 m/min Cutting width: 754 mm Chodpfx Aewxuzmoddsf Electrical connection: 1.5 kW, 400V/50Hz/3AC Width of machine with adjustment lever: 1296 mm Depth of machine (with discharge belts): 1915 mm Height of machine: 1224 mm Weight: 415 kg

Condition: not inspected (used), functionality: unexamined, machine/vehicle number: 068-071/270, throat depth: 150 mm, table width: 280 mm, table length: 280 mm, distance table to ram: 355 mm, stroke length: 280 mm, No minimum price – guaranteed sale to the highest bidder! Placing a bid requires timely collection between 28.07.2025 and 31.07.2025. TECHNICAL DETAILS Rated force: 3.15 Mp Operating pressure: 125 kp/cm² Upward speed: 100 mm/s Downward speed: 300 mm/s Ram stroke: 280 mm Throat: 150 mm Maximum distance between table and ram: 355 mm Cedpfx Ajwvh R Asddjhf Table dimensions: 280 mm x 280 mm MACHINE DETAILS Dimensions: 750 mm x 630 mm x 1,700 mm Weight: 750 kg Connected load: 1.5 kW Rated current: 3.8 A Operating voltage: 380 V / 50 Hz

Condition: used, Year of construction: 2002, Screw compressor, single-stage, oil-free. Max. flow rate approx.: 1080 m³/h Cedpfx Aovcqt Ioddohf Power: 75 kW Length: 1605 mm Width: 1250 mm Height: 2000 mm

Condition: used, Technical details: weight of the machine ca.: 4,0 t machine dimensions LxWxH: 1,8 x 1,8 x 0,9 m Machine table with 5 indexing tables for multi-side machining Application: Multi-side machining of workpieces in circular transfer machines in one operation on 5 indexing tables with clamping devices. Design: Round, fixed body with 5 round tact tables, which are arranged in the shape of a pentagon, and a centrally mounted turntable. Description: Turntable center = type Pentagon, diagonal 830mm; swing diameter Ø 873mm, side length 513mm 5x rotary indexing table, as a regular pentagon on machine body, center circle Ø = 1280mm, table shape truncated square 380x380mm, clamping device via 4 pieces make Röhm truncated cone clamping devices and 1 central centering flange, 360 ° rotatable, workpiece Ø approx. 730mm Actuation / drive is hydraulic Chjdpsu N D S Uefx Addsf *