Used Feed Hopper for sale (12,223)

Condition: reconditioned (used), Technical data feed hopper with hydraulic moving floor and bag opener for recyclables from yellow bags and residual waste: Manufacturer BRT HARTNER GmbH Type HP5-3035 Year of construction 2015 Hopper volume 30 m³ Drive line 17.5 kW Dimensions in current state 13,200 x 3,050 x 4,350 mm (l x w x h) Condition of the machine: The feed hopper with bag opener was used at a large recycling plant, where recyclable materials from yellow bags or commercial waste were tipped into the hopper using wheel loaders, the bags were opened using the bag opener, and the recyclable materials were transported to a sorting plant or the commercial waste was transported in measured quantities for further processing. The system functioned flawlessly until it was dismantled and replaced with a larger system with higher throughput capacity. The machine was dismantled into individual parts in our workshop, partially overhauled, reassembled, and tested during operation. The following overhaul work was carried out and the following spare parts were replaced: Dismantling of the feed hopper and bag opener into individual parts. Cleaning, partial sandblasting, priming and painting of the steel parts. Various wear and cover plates were newly manufactured and installed. Cutting off the worn ends (approx. 40cm) of the push floor pipes. Welding on the new pipes and smoothing the push floor pipes. Replacement of all plastic sliding plates for the hydraulic push floor. Removal of the hydraulic unit from the push floor, emptying of the hydraulic oil tank, replacement of the oil filters, refilling with new hydraulic oil. Replacement of the three hydraulic blocks, all valves, the oil sight glass and all hydraulic hoses from the hydraulic unit. The seal kit and hydraulic hoses were replaced on all three hydraulic cylinders of the push floor. Codoyizxrspfx Aa Norb All six limit switches (proximity sensors) on the push floor were replaced. The conveyor chains on the left and right of the scraper conveyor were replaced. Seven carrier bars on the scraper conveyor were replaced. The drive motor for the ripper blades was replaced. All nine pneumatic cylinders for the pressure pipes were replaced. All pneumatic lines and connections were replaced. All of the plastic sliding plates for the hydraulic operation of the bag opener were replaced. The bag opener can be moved vertically so that the system can also be used for commercial waste or residual waste without the bag opener. The side impact protection plates on both sides were replaced. Various wear parts of the bag opener have been replaced. The entire system has been rewired and reconnected. The system control in the control cabinet has been retrofitted by the manufacturer BRT Hartner to a self-sufficient individual control system and the standard programme has been reloaded into the control system. The system has been commissioned and tested by the manufacturer BRT Hartner, see the function video. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: not inspected (used), Year of construction: 1959, functionality: unexamined, pressing force: 8 t, stroke length: 56 mm, total length: 1,600 mm, total width: 1,000 mm, overall weight: 300 kg, No reserve price – guaranteed sale to the highest bidder! Placing a bid commits you to timely collection between 23/06/2026 and 26/06/2026! TECHNICAL DETAILS Pressing force: 8 t Adjustable stroke: 8 mm to 56 mm Ram adjustability: 30 mm MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 1,600 x 1,000 x 1,500 mm Weight: 300 kg EQUIPMENT Feed hopper (diameter: 500 mm) External reference: 36 Cedpfx Aoy D S H Rea Norb

Condition: not inspected (used), Year of construction: 1968, functionality: unexamined, pressing force: 8 t, stroke length: 56 mm, total length: 1,600 mm, total width: 1,000 mm, overall weight: 300 kg, No minimum price – guaranteed sale to the highest bidder! Bidding obliges prompt collection between 23/06/2026 and 26/06/2026! TECHNICAL DETAILS Press force: 8 t Adjustable stroke: 8 to 56 mm Ram adjustment: 30 mm MACHINE DETAILS Dimensions & weight Dimensions (L x W x H): 1,600 x 1,000 x 1,500 mm Weight: 300 kg Crjdpfoy D S A Esx Aa Nob EQUIPMENT Feeder bowl (diameter: 500 mm) External reference: 37

Condition: not inspected (used), Year of construction: 1956, machine/vehicle number: 9904, functionality: unexamined, pressing force: 8 t, stroke length: 70 mm, table width: 350 mm, table length: 440 mm, overall weight: 600 kg, No minimum price – guaranteed sale to the highest bidder! Placing a bid obligates you to collect the item on time between 23/06/2026 and 26/06/2026! TECHNICAL DETAILS Pressing force: 8 t Adjustable stroke: 8 - 70 mm Ram adjustment: 30 mm Table dimensions: 440 x 350 mm MACHINE DETAILS Dimensions & weight Cjdpfey D Sp Sex Aa Norb Dimensions (L x W x H): 1,300 x 1,100 x 1,300 mm Weight: 600 kg EQUIPMENT Conveyor by manufacturer RNA (diameter: 550 mm) External reference: 62

Condition: not inspected (used), functionality: unexamined, overall weight: 80 kg, total height: 1,200 mm, rotational speed (max.): 3,000 rpm, machine/vehicle number: 05133, No reserve price – guaranteed sale to the highest bidder! Placing a bid obligates the buyer to collect the item on time between 23/06/2026 and 26/06/2026! TECHNICAL DETAILS Crsdpfx Aasy D Nhle Nob Speed: 3,000 rpm MACHINE DETAILS Rated voltage: 200 V Frequency: 50 Hz Rated current: 3.77 A Power: 753 VA Vibration frequency: 50 Hz Dimensions & Weight Dimensions (L x W x H): 600 x 500 x 1,200 mm Weight: 80 kg External reference: 61

Condition: used, functionality: fully functional, gearing type: mechanical, fuel type: electric, Year of construction: 2019, Height: approx. 4,700 mm Bunker volume: approx. 60 m³ Plate conveyor width / length: approx. 1,150 x 4,800 mm Codpfx Aewk E Emoa Nsrb Length: approx. 7,400 mm Width: approx. 5,200 mm Bonfigioli gearbox: Type SK 185 Siemens electric motor: 346 to 524 volts, 160 watts

Condition: ready for operation (used), * Brand: Nordberg * Model: feeding table with hopper * ding table: 5000 x 1100 mm * Dim. hopper: 5500 x 3700 x 2500 mm Crjdeywmkkjpfx Aa Nob * Driving: 22 kW E-motor

Condition: good (used), conveyor belt, belt conveyor, transport belt, belt conveyor, belt conveyor, flat belt conveyor -Conveyor belt: Belt conveyor on solid base frame with feed hopper -Speed: 3.4/6.6 m/min -Belt width: 190 mm Credpsvazpusfx Aa Neb -Conveyor length: 745 mm -Drive: VEM 0.14/0.25 kW, see photo nameplate -Transport dimensions: 460/1255/H1185 mm -Weight: 149 kg

Condition: good (used), Feed container for blasting system, sandblasting system, blasting system, sandblasting cabinet, rotary basket system, wire belt, overhead conveyor and roller conveyor blasting system, free blasting system -Handover: in its current condition as inspected -System: Individual components see photos -Feed container: Type Exactomat 2 G - 60 Cjdpfx Asqcyzwsa Njrb -Vacuum pump flow rate: 26.2 m³/h -Dimensions: 830/580/H1730 mm -Weight: 296 kg

Condition: repair required (used), feed hopper / buffer hopper Csdpfx Aaswydmne Norb

Year of construction: 2025, condition: new, For sale: New buffer hopper with a loading grate equipped with a removable deagglomeration screen Codjw Tc Txepfx Aa Norb

Condition: used, No. 10012 Crodpfx Aev N E Iyea Nsb Feed hopper Rema Used Metal plate conveyor / steel plate belt Defective gearbox (Bonfiglioli) Drive power 15 kW Belt width 2000 mm Axis length 10000 mm The system has been out of operation since the end of January 2025 due to gearbox damage Without output conveyor Transport dimensions approx. 15000 x 3000 x 4000 / 5500 mm LWH Sale on behalf of customer, ex location near 78628 Rottweil, without dismantling, without transport and assembly Errors in description and price excepted Dismantling, transport and loading by us optionally possible To avoid possible misunderstandings, an on-site inspection is possible and recommended by appointment Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale Any warranty is excluded for used machines, the following applies: “purchased as viewed” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Year of construction: 2021, operating hours: 1,513 h, condition: used, functionality: fully functional, overall weight: 11,500 kg, total length: 6,050 mm, total width: 2,450 mm, total height: 2,700 mm, machine/vehicle number: B205, Our robust FEED HOPPER is specifically designed for the precise dosing of challenging, hard-to-meter feed materials. Equipped with a plate belt, the hopper reliably handles abrasive or coarse-grained materials. With a capacity of 7 m³ and an optionally integrable leveling roller, the feed rate can be adjusted. Csdpjxta D Tofx Aa Nsrb This module is part of our rental fleet.

Condition: excellent (used), Offered is a used feed hopper with pre-screening. Codpsv N H Hdsfx Aa Njrb Manufacturer: Haver & Boecker. Year of manufacture: 1995. Type: UF 1200x3650. Very good condition, fully functional.

Condition: good (used), - Output: up to max. 30to/h - Motor: 400V, 50Hz - Without electrical equipment Mass: - Length: approx. 2000mm + discharge screw - Width: approx. 1700mm - Height: approx. 1700mm Csdpjmn I Nqofx Aa Njrb

Year of construction: 2005, condition: excellent (used), We offer a used dosing hopper with internal dosing belt and internal conveying rake: Cedpsiuxucofx Aa Nerb Dimensions: L: 3.90 m, W: 0.86 m, H: 1.50 m. Belt width: 0.75 m. Including an associated conveyor belt: Length: 4.20 m, belt width: 0.50 m. Very good condition. Technical details: See photos.

Condition: used, Stainless steel dosing screw, feed screw conveyor, auger Equipped with additional feed hopper with aluminium lid Screw diameter: 200 mm Motor power: 3 kW, 36 rpm Total length: 1730 mm See our other listings Csdpfjx Nzu Usx Aa Nsrb VMA Wekerom

Condition: ready for operation (used), functionality: fully functional, A good used Hopper Feeder fopr feeding small parts into assembly machine or feeding a bowl feeder with bulk parts - stainless steel conveyor - flighted belt (comes with a second spare belt also) - three phase geared drive unit - 24 V DC sensors (2) for control of belt index if required Ready to ship worldwide Crsdpfxew D Ev Ee Aa Nsb More pictures and videos available upon request

Condition: new, New Conveyor with overhead feeder hopper Csdpowd Nthofx Aa Nsrb Both units are mobile on castors Feeder hopper with opening end door, adjustable exit gate to conveyor Feeder hopper dimensions 800mm x 740mm x 600mm deep Conveyor belt dimensions 1800mm x 230mm W x 1260mm H Conveyor height is adjustable VFD on conveyor drive

Condition: new, functionality: fully functional, Year of construction: 2026, CONSTMACH vibrating feeder bunkers are high-efficiency equipment designed to ensure continuous and balanced feeding of crushers in stone crushing and screening plants. These bunkers are placed in front of primary impact crushers or jaw crushers to ensure a homogeneous flow of material. This increases the capacity of the crushers, balances the loads on the intermediate crushers, and ensures continuity in the overall production line. The vibrating feeding system prevents sudden loads, eliminating the risk of overloading on conveyor belts and thermal damage to equipment. Thanks to CONSTMACH's special design, the vibrations in the bunkers are smooth and balanced. This ensures both a steady material flow and extended machine life. Otherwise, uneven feeding could cause serious wear on crusher hammers, conveyor belts, and bearings. Using a vibrating feeder bunker helps reduce maintenance costs, increase operational efficiency, and maintain long-term performance throughout the facility. Vibrating Feeder Bunker Technical Specifications Model: CPG - 09 Body Size: 2,500 x 520 mm Grid Size: 820 mm Motor Power: 2 x 3 kW Crjdpfx Aaexqf Sde Neb Bunker Volume: 8 - 10 - 15 m³ Capacity: 80 - 100 t/h Weight: 8,000 kg Model: CPG - 10 Body Size: 3,000 x 850 mm Grating Size: 1,160 mm Motor Power: 2 x 4.5 kW Hopper Capacity: 10 - 15 - 20 m³ Capacity: 150 - 200 t/h Weight: 12,000 kg Model: CPG - 11 Body Dimensions: 4,600 x 1,100 mm Grate Dimensions: 1,400 mm Motor Power: 2 x 9.2 kW Bunker Volume: 15 - 20 - 30 m³ Capacity: 200 - 300 t/h Weight: 18,000 kg Model: CPG - 13 Body Size: 4,880 x 1,370 mm Grating Size: 1,840 mm Motor Power: 2 x 11 kW Bunker Volume: 30 - 45 - 50 m³ Capacity: 350 - 500 t/h Weight: 26,000 kg Why Choose CONSTMACH Vibrating Feeder Bunkers? CONSTMACH is a trusted brand in the industry with years of engineering experience and high production standards. Our products stand out with their durable body structure, low maintenance requirements, and energy-efficient motor systems. Each one undergoes high-quality control processes to ensure long-lasting use. CONSTMACH Vibrating Feeders increase the performance of your crushing plant while minimizing your operating costs. If you are looking for quality, durability, and maximum efficiency, CONSTMACH is the right solution. What Do We Do at Constmach? Constmach is a leading machine manufacturer serving the construction and mining industries with a wide range of products. Our product portfolio includes concrete block making machines, stationary and mobile concrete plants, stone crushing machines, stone crushing and screening plants, sand washing machines, sand making machines, asphalt plants, conveyor belt systems, jaw crushers, and mobile crushing plants. With its high quality standards, innovative production approach, and customer-focused solutions, Constmach stands out as a reliable brand in both national and international markets. Our products continue to be the preferred choice of industry professionals due to their durability, efficiency, and long-lasting performance.

Condition: like new (used), Machine ready for operation, hopper with roller inspection feeder. Crodpfx Aajytnf To Njb

Condition: used, Linear feeder / Vibratory feeder / Sorting device Crsdpfxoxf Urve Aa Neb Vibratory linear feeder, vibratory hopper, dosing hopper, storage hopper Vibratory bowl feeder, bowl feeder Vibratory bowl, screw feeding system with vibratory feeder for screwdriving technology Feeding system, feed unit Manufacturer: RNA Rhein-Nadel Automation GmbH Year of manufacture: approx. 2000 Useful load: approx. 1.5 kg Oscillation frequency: 100 Hz / 6000 rpm Mains connection: 220 Volt, 50 Hz - Oscillating plate L x W = 170 x 60 x 12 mm - Mounted track length 340 mm - Overall height with base plate and oscillating plate approx. 115 mm Required space L x W x H: 400 x 280 x 400 mm Weight: 9 kg Good condition

Condition: refurbished (used), A feed hopper is being offered. Dimensions HxWxL (with frame): 3.15 m x 2.00 m x 1.70 m. (hopper only): 2.00 m x 2.00 m x 1.70 m. Capacity: approx. 6.5 m³. Sandblasted, primed, and newly painted. New support legs. Csdpfxjx A Ekwe Aa Norb

Condition: ready for operation (used), Year of construction: 1988, functionality: fully functional, machine/vehicle number: 4004/1135, conveyor belt thickness: 3 mm, conveyor belt width: 600 mm, power: 5 kW (6.80 HP), The payment deadline for the machine is 18.05.2026! Submission of a bid requires timely collection by 22.05.2026! TECHNICAL DETAILS Band width: 100 - 600 mm Band thickness: 0.5 - 3 mm Max. load: 11 t MACHINE DETAILS Voltage: 24 / 380 V Frequency: 50 Hz Power: 5 kW EQUIPMENT Decoiler Integrated feed unit Credpey Nkaaofx Aa Nob

Year of construction: 2026, condition: new, Ready-to-deliver press feeding line for scaffolding plank production with 4 Ton decoiler, straightener feeder and 200 Ton C-type press. Bosporas Machinery is a manufacturer of coil processing, press feeding and roll forming systems, delivering high-performance and customized industrial solutions worldwide with strong R&D capabilities. This scaffolding plank feeding line is available from stock and ready for fast delivery. The system is designed for perforating, punching and feeding operations in scaffolding plank production and similar metal forming applications. The line combines stable coil feeding, precise straightening and high-capacity press performance in a compact and efficient production solution. Ideal for companies looking for immediate production capacity without long manufacturing lead times. ⚡ FAST DELIVERY ADVANTAGE Stock machine – ready for shipment Fast delivery opportunity Reduced investment waiting time Ready for industrial production setup ⚙️ TECHNICAL CONFIGURATION Coil Width: up to 600 mm Mechanical Decoiler: 4 Ton Capacity Straightening Servo Feeder System C-Type Mechanical Press: 200 Ton Capacity Servo synchronized feeding operation Heavy-duty industrial structure 🔧 LINE COMPONENTS 4 Ton Hydraulic Decoiler Straightening Unit Servo Feeder System 200 Ton C-Type Press Electrical & Automation System Operator Control Panel ⚙️ ENGINEERING FEATURES High precision feeding performance Stable straightening and synchronized press operation Heavy-duty press structure for continuous production Credpfx Ajy Nnftsa Neb Servo motor controlled feeding system Compact and operator-friendly design Suitable for integration with roll forming systems ⚡ OPERATIONAL ADVANTAGES Immediate availability from stock Reliable and continuous production Reduced setup and commissioning time Flexible use for punching and perforation applications Short lead time compared to European manufacturers 🏭 APPLICATION AREAS Scaffolding plank production Perforated metal production Sheet metal punching applications Roll forming pre-feeding systems Construction industry components