Used Firing Furnace for sale (2,132)

Year of construction: 2017, condition: good (used), functionality: fully functional, Furnace Housing Dimensions External dimensions: - approx. 3,800 x 4,300 x 2,200 mm Internal (usable) furnace dimensions: - approx. 2,440 x 1,400 x 1,200 mm Batch Load weight: - 9 boxes (net weight 50 kg/each) - approx. 250 kg material per box - stack arrangement 3x3 Ndodpfx Agjxcybkefjd Performance Data - 1 gas recuperator burner - 160 kW rated heating capacity - Max. allowable chamber furnace temperature 720°C - Max. allowable post-combustion temperature 1,020°C - 1 temperature control zone Temperature Control Range - Chamber furnace 480°C – 700°C - Post-combustion 850°C – 1,000°C Supply Media - Natural gas L or H - Gas inlet pressure 80 mbar - Voltage 400 V - Frequency 50 Hz - Connected load 8 kVA - Compressed air 6 bar, dry, oil-free Material: e.g. brass or bronze

Year of construction: 2015, condition: used, external dimensions: lenght: 3900 mm width: 1320 mm height: 1090 mm (above base frame) muffle lenght: 3960 mm mesh belt: 480 mm width clear height 140 mm Nedpfxoclupds Agfjdd max. furnace area temperature: 750°C max. temperature inside the muffle: 700°C water cooled ventilators : 3 electrical connected loads: three-phase: 3 x 400 V, 50 Hz power consumption: 75 kVA heating power, 3 zones each: 24 kW = 72 kW PLC : Siemens S7

Condition: excellent (used), Nabertherm N450 ceramic firing kiln, maximum temperature 1280 degrees C. German-made kiln. The kiln is equipped with a very intuitive controller with 6 programs. New spirals have been installed in the kiln, which guarantee the achievement of maximum temperature. Chamber with a capacity of 450 liters. Chamber dimensions: Height 100 cm Width 60 cm Depth 75 cm External dimensions Height 182 cm Width 103 cm Depth 145 cm Ndodswdzt Hjpfx Agfod Power supply 400 V Power 24 kW Maximum temperature 1280 degrees C Kiln in very good condition.

Condition: ready for operation (used), A small tunnel oven for pizza production is available. Heating capacity: 10kW, temperature range: 120°C-300°C, conveyor time: 90s-20min, conveyor belt dimensions X/Y: 460mm/1320mm, baking area X/Y: 460mm/610mm, production capacity for 26cm pizzas: approx. 70 pieces/h, machine dimensions X/Y/Z: approx. 1450mm/1000mm/450mm, weight: approx. 170kg. An on-site inspection is possible. Ndjdpfxexapgqe Agfed

Year of construction: 1988, condition: used, functionality: unexamined, machine/vehicle number: 26535, Heating: gas Fuel gas: propane Gas overpressure: 80-100 mbar Working temperature: 150-750 °C Heating output: 550 °C (300 kg/h steel) Max. permissible load weight: 350 kg gross Type of loading: automatic with loading device Type of unloading: manually via loading device Max. batch dimensions: 610x910x460 mm Ndodpfx Agsvkwifsfsd

Condition: used, Year of construction: 1988, operating hours: 30,000 h, functionality: fully functional, machine/vehicle number: 20992, Dear Mr. / Mrs., we have opportunity to offer you IPSEN VTTC-324 from 1988. Characteristic of vacuum furnace: Sn = 165 kVA Un = 400 V, 50Hz In = 240 A Useful dimension: 450mm x 600mm x 900mm Power of heaters = 120 kW Voltage of heaters = 43V, 50Hz Ndodpfx Aewah R Rsgfed Current of heaters = 1613 A Temperature range = 350 - 1320 C Absolute vacuum = 1 x 10e-5 (diffusion pump) Absolute pressure = 5 bar Also, with furnace is coming lot of spare parts and equipment for thermal heating process (tank for gas, heaters, lot of controllers, chargers and everything). For all information that you need, please contact me.

Condition: ready for operation (used), Year of construction: 2012, functionality: fully functional, temperature: 630 °C, power: 450 kW (611.83 HP), plate length: 1,400 mm, plate width: 1,100 mm, TECHNICAL DETAILS Device type: Glass heating furnace for deep processing Application: Homogeneous heating and subsequent cooling of flat glass Suitable glass: clear float glass Maximum glass size: 1,400 × 1,100 mm Furnace Furnace width: 1,600 mm Opening/closing height: 500 mm Opening mechanism: electric Motor power for opening/closing: 1.5 kW Temperature: 630 °C Rollers Roller type: quartz rollers Roller diameter: 60 mm Number of quartz rollers: 46 Number of rollers in the cooling section: 22 Roller spacing: 100 mm Heating Heating system: electric with forced convection Heating power: 450 kW Control: PLC control with zone-dependent temperature regulation Speed Speed range: 1 – 10 m/min MACHINE DETAILS Supply voltage: 380 V Power supply: 3-phase, 5-wire AC Total weight: 10 t System configuration Components: Computer, control cabinet, power control cabinet, loading table, heating section, coating section, cooling section, unloading table Process sequence 1. Glass loading: The flat glass is placed on the loading table and transported into the heating section. 2. Heating: In the heating section, the glass is uniformly heated to high temperatures. 3. Coating: After heating, a special coating is applied in the coating section. 4. Cooling (Annealing): In the cooling section, the glass is uniformly and slowly cooled to reduce stress. 5. Glass unloading: The processed glass is conveyed to the unloading table and removed. EQUIPMENT - Computer - Control cabinet - Power control cabinet - Loading table - Heating section - Coating section Nedpfxswtfiqo Agfjdd - Cooling section - Unloading table - Zone-wise controllable heating system via PLC control - Forced convection system for uniform heat distribution - Quartz rollers with close spacing for precise glass guidance - Integrated cooling section with 22 rollers for controlled glass cooling The furnace has been dismantled into components of approximately two meters in length. This allows transport with standard trucks.

Condition: used, Electrically heated tempering furnace with protective atmosphere Type: TSK-8-10-12-80 Temperature: max. 800°C Internal dimensions (W x H X D):800 x 1050 x 1200 mm Heating power: 80 kW Atmosphere fan: 4,0 kW Ndodpfx Aoxcphmsgfed

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. Ndedpfx Agsfx Nfmofsd History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.

Year of construction: 2008, condition: ready for operation (used), Loading chamber dimensions: 280x580mm, loading height: 700mm, max. load: 300kg, with protective housing and documentation, machine was functional until the end, complete maintenance would have to be carried out on the machine, inspection is possible. Ndsdoqgfbgopfx Agfed

Year of construction: 1986, condition: used, functionality: unexamined, machine/vehicle number: 43563, Heating: Gas Fuel gas: Propane Gas overpressure: 10-50 mbar Ndjdpfx Ajvkwqvsgfsd Working temperature: 150-450 °C

Condition: used, TECHNICAL DETAILS Quenching tank for stirring oil quenching Njdpfx Aoug U Thjgfodd - power : 0.25 [kW] - voltage : 3 x 380 [V]

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters. Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process. Series SL Power Electricity Forced air circulation Two-channel USB temperature recorder Number of temperature sensors MTS 2+ Wall insulation thickness (mm) 240 Ceiling insulation thickness (mm) 300 Number of programs 20 Ndjdpfxefy T H Io Agfod Max. Number of steps in the program 10 Average heating time up to 180 ° C 40min 35min 25min 25min 20min Number of door leaves 2 Diagnostics / update via the internet Media consumption meter Stainless steel ceiling elements Direct heating Explosionproof closures Silicone door seal Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff. ThPID was created to offset the effect of inertia called hysteresis. The standard solution is based on a circuit that on / off heats with constant power. ThPID is a system in which, by adjusting the voltage at the setpoint temperature, the heating power that is currently needed is selected - minimizing the effect of temperature fluctuations. The ThPID system further allows the heating power of the furnace to be cut to a specified percentage, for example in the absence of power at the moment.The MTS is designed to provide realistic reading of the temperature of the oven. The standard measurement is based on a temperature measurement which is often wrong. MTS is a system of multiple sensors localized in the extreme places of the chamber.

Condition: ready for operation (used), Max. Working temperature: 1120°, heated length: 1000mm, cooling length: 1850mm, channel height: 40mm, conveyor belt width: 110mm, throughput speed: 100-1000mm/min, splitting gas consumption: 1.5-2.5Nm³/h, touch panel: Siemens SIMATIC HMI, length: 5000mm, width: 650mm, height: 1350mm, with integrated ammonia splitter GSP 25 FA, integrated gassing panel, protective gas from ammonia splitter (on-site ammonia supply) + N2 purge gas as required, MSR system with Siemens PLC and touch HMI, atmosphere monitoring, process documentation, on-site inspection is possible. Ndjdpfxsq Ttz Es Agfod

Year of construction: 2020, condition: new, 7 "Touch Panel The large color touch panel looks aesthetically and is comfortable and intuitive to use. You will set all important parameters on it. Memory of 20 programs with 10 events It is possible to save up to 20 programs and activate up to 10 consecutive time-temperature events arranged in the heating curve. Ndjdpfxsfz U Tqj Agfod This is especially needed for more demanding processes. Information on gas / oil consumption The consumption is calculated based on the burner settings. This feature will allow you to estimate the cost of a given cycle, plan consumption and check personnel. Dual-channel recorder of USB cycle parameters Each furnace is equipped with a recorder that records all firing parameters, including two temperature channels - like in an airplane black box, on a USB flash drive. The system also enables the analysis of monthly / daily statements, including media consumption and performance. Each start of heating, opening the door, can be recreated, a few years back. Such a dedicated option is not offered by any manufacturer. It is a system developed from scratch by our programmers Automatic smoke exhaust chimney The chimney can be programmed to open a few minutes before the end of the firing in order to smoke the chamber. It can be remotely controlled from the panel, it does not need to be done mechanically as in most structures. Minute forecast until the end The cycle has started, how long will it end? calculating the heating dynamics, we will count it and show on the display how much longer it will take. To open it, just pull the door. The lock has adjustable pressure of the door, to close it just push it, the lock will catch the door and automatically pull it back. In order to minimize the effect of heating the hall when opening the door, a hood is installed above the door to remove some of the heat to other places. The MTS system was created to provide a real reading of the temperature of the furnace chamber. Standard measurement is based on one temperature measurement which is often wrong.MTS is a system of many sensors located in the outermost places of the chamber. The multi-zone heating system ensures a firing quality that has been so far unique. Each normal oven has only one heating zone and only one temperature measurement! The multi zone heat system supports up to 8 independent heating zones in one oven. Each heating zone has as many as 3 temperature sensors! When there are temperature differences between zones, they are automatically equalized! The system helps to combat the problem when elements of different material thicknesses enter the furnace.

Year of construction: 2010, condition: ready for operation (used), Heated surface: 1600x2600/ 2000x2000mm, nominal power: 120kW, length: 2600mm, width: 2300mm, with control cabinet and conveyor. Ndedpfx Agjifpuajfed

Year of construction: 2020, condition: new, 7 "Touch Panel The large color touch panel looks aesthetically and is comfortable and intuitive to use. You will set all important parameters on it. Ndedofz I Rxspfx Agfed Memory of 20 programs with 10 events It is possible to save up to 20 programs and activate up to 10 consecutive time-temperature events arranged in the heating curve. This is especially needed for more demanding processes. Information on gas / oil consumption The consumption is calculated based on the burner settings. This feature will allow you to estimate the cost of a given cycle, plan consumption and check personnel. Dual-channel recorder of USB cycle parameters Each furnace is equipped with a recorder that records all firing parameters, including two temperature channels - like in an airplane black box, on a USB flash drive. The system also enables the analysis of monthly / daily statements, including media consumption and performance. Each start of heating, opening the door, can be recreated, a few years back. Such a dedicated option is not offered by any manufacturer. It is a system developed from scratch by our programmers Automatic smoke exhaust chimney The chimney can be programmed to open a few minutes before the end of the firing in order to smoke the chamber. It can be remotely controlled from the panel, it does not need to be done mechanically as in most structures. Minute forecast until the end The cycle has started, how long will it end? calculating the heating dynamics, we will count it and show on the display how much longer it will take. To open it, just pull the door. The lock has adjustable pressure of the door, to close it just push it, the lock will catch the door and automatically pull it back. In order to minimize the effect of heating the hall when opening the door, a hood is installed above the door to remove some of the heat to other places. The MTS system was created to provide a real reading of the temperature of the furnace chamber. Standard measurement is based on one temperature measurement which is often wrong.MTS is a system of many sensors located in the outermost places of the chamber. The multi-zone heating system ensures a firing quality that has been so far unique. Each normal oven has only one heating zone and only one temperature measurement! The multi zone heat system supports up to 8 independent heating zones in one oven. Each heating zone has as many as 3 temperature sensors! When there are temperature differences between zones, they are automatically equalized! The system helps to combat the problem when elements of different material thicknesses enter the furnace.

Year of construction: 1991, condition: ready for operation (used), Working/ nominal temperature: 800/ 850°C, inner dimensions: 1100x500x260mm, heating output: 120kW, connected load: 1.5kW, with documentation, without accessories or spare parts, an inspection is possible. Ndodpfx Agjpcgzgsfed

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Nsdpfxofzb Rce Agfjdd Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.

Condition: ready for operation (used), A long furnace Löcher with charging trolley operation is available. The furnace was part of a bending plant for the production of flange rings. Interior dimensions X/Y/Z: approx. 14000mm/500mm/1500mm, max. temperature: 1200°C, total furnace dimensions X/Y/Z: approx. 4100mm/3850mm/16000mm, control: CNC. The machine has a control defect. Documentation available. On-site inspection is possible. Ndsdpfx Agewkiipofjd

Year of construction: 2020, condition: new, 7 "Touch Panel The large color touch panel looks aesthetically and is comfortable and intuitive to use. You will set all important parameters on it. Memory of 20 programs with 10 events It is possible to save up to 20 programs and activate up to 10 consecutive time-temperature events arranged in the heating curve. This is especially needed for more demanding processes. Information on gas / oil consumption The consumption is calculated based on the burner settings. This feature will allow you to estimate the cost of a given cycle, plan consumption and check personnel. Dual-channel recorder of USB cycle parameters Each furnace is equipped with a recorder that records all firing parameters, including two temperature channels - like in an airplane black box, on a USB flash drive. The system also enables the analysis of monthly / daily statements, including media consumption and performance. Each start of heating, opening the door, can be recreated, a few years back. Such a dedicated option is not offered by any manufacturer. It is a system developed from scratch by our programmers Automatic smoke exhaust chimney The chimney can be programmed to open a few minutes before the end of the firing in order to smoke the chamber. It can be remotely controlled from the panel, it does not need to be done mechanically as in most structures. Nedefz Anpjpfx Agfedd Minute forecast until the end The cycle has started, how long will it end? calculating the heating dynamics, we will count it and show on the display how much longer it will take. To open it, just pull the door. The lock has adjustable pressure of the door, to close it just push it, the lock will catch the door and automatically pull it back. In order to minimize the effect of heating the hall when opening the door, a hood is installed above the door to remove some of the heat to other places. The MTS system was created to provide a real reading of the temperature of the furnace chamber. Standard measurement is based on one temperature measurement which is often wrong.MTS is a system of many sensors located in the outermost places of the chamber. The multi-zone heating system ensures a firing quality that has been so far unique. Each normal oven has only one heating zone and only one temperature measurement! The multi zone heat system supports up to 8 independent heating zones in one oven. Each heating zone has as many as 3 temperature sensors! When there are temperature differences between zones, they are automatically equalized! The system helps to combat the problem when elements of different material thicknesses enter the furnace.

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) Ndsdpfsfy T Spex Agfod For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning. Ndedpfxsfzccne Agfjd

Year of construction: 2020, condition: new, 7 "Touch Panel The large color touch panel looks aesthetically and is comfortable and intuitive to use. You will set all important parameters on it. Memory of 20 programs with 10 events It is possible to save up to 20 programs and activate up to 10 consecutive time-temperature events arranged in the heating curve. This is especially needed for more demanding processes. Information on gas / oil consumption The consumption is calculated based on the burner settings. This feature will allow you to estimate the cost of a given cycle, plan consumption and check personnel. Dual-channel recorder of USB cycle parameters Each furnace is equipped with a recorder that records all firing parameters, including two temperature channels - like in an airplane black box, on a USB flash drive. Ndedpfsfy Txyex Agfsd The system also enables the analysis of monthly / daily statements, including media consumption and performance. Each start of heating, opening the door, can be recreated, a few years back. Such a dedicated option is not offered by any manufacturer. It is a system developed from scratch by our programmers Automatic smoke exhaust chimney The chimney can be programmed to open a few minutes before the end of the firing in order to smoke the chamber. It can be remotely controlled from the panel, it does not need to be done mechanically as in most structures. Minute forecast until the end The cycle has started, how long will it end? calculating the heating dynamics, we will count it and show on the display how much longer it will take. To open it, just pull the door. The lock has adjustable pressure of the door, to close it just push it, the lock will catch the door and automatically pull it back. In order to minimize the effect of heating the hall when opening the door, a hood is installed above the door to remove some of the heat to other places. The MTS system was created to provide a real reading of the temperature of the furnace chamber. Standard measurement is based on one temperature measurement which is often wrong.MTS is a system of many sensors located in the outermost places of the chamber. The multi-zone heating system ensures a firing quality that has been so far unique. Each normal oven has only one heating zone and only one temperature measurement! The multi zone heat system supports up to 8 independent heating zones in one oven. Each heating zone has as many as 3 temperature sensors! When there are temperature differences between zones, they are automatically equalized! The system helps to combat the problem when elements of different material thicknesses enter the furnace.

Year of construction: 2020, condition: new, 7" Touchpad Nedjfzkqmjpfx Agfodd Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.