Used Hollow Spindle Lathe for sale (14,950)

Condition: good (used), Leadscrew & feed rod lathe WEILER CONDOR - Original paint - Centre height: 165 mm - Swing over bed: 330 mm - Swing over cross slide: 170 mm - Distance between centres: 800 mm - Spindle speeds: 24 - 2800 rpm - Automatic longitudinal/cross feeds - Spindle bore: 38 mm - Tailstock MT 3 - Collet chuck system + 17x collets - Three-jaw chuck - Multifix toolpost with inserts - Electric chuck guard - Chip guard rear panel - Work lamp - Various accessories - Documentation Dimensions: LxWxH 1.8x0.9x1.6 m / Weight 800 kg Crsdpjx A D Ubsfx Addsk Errors and omissions excepted.

Condition: used, Year of construction: 1990, functionality: fully functional, turning diameter over cross slide: 570 mm, turning diameter over bed slide: 340 mm, spindle speed (max.): 2,500 rpm, The machine operates fully. The machine bed is in excellent condition. Runs very quietly. Crsdpfxew E D Rqj Addjk

Condition: used, Year of construction: 1979, functionality: fully functional, turning diameter: 640 mm, center height: 320 mm, turning length: 2,000 mm, Leadscrew and feedshaft lathe VDF with digital readout, powered top slide, 3-axis feed with rapid traverse, 3-jaw chuck, faceplate, Multifix toolholder with 5 inserts. Credpfx Asxz Edzoddsk

Condition: used, Year of construction: 1999, functionality: fully functional, Weiler Primus VC lathe, year 1999, equipped with a 3-axis Siemens digital readout, 3-jaw chuck, Multifix toolpost, rear splash guard, and electric chuck guard. The machine is in good, ready-to-use condition and can be demonstrated under power by appointment. Crjdpfxjx Afvgo Addsk

Condition: excellent (used), Year of construction: 1963, center height: 102 mm, turning length: 450 mm, Very good lathe for demanding hobbyists, motorcycle workshops, blacksmiths, and similar businesses. Runs perfectly. Power feed along the longitudinal axis. Thread cutting possible. 40–3000 rpm. 3 x 400 Volt, 16 A supply. Accessories are shown in the photos. An additional cross slide is included in the scope of delivery, but it does not fit this machine and is more suited for a Schaublin 102 turret lathe or a similar model. Cjdpfx Adox Anuloderk Transport in a closed Euro trailer is possible.

Condition: refurbished (used), Year of construction: 1981, functionality: fully functional, turning diameter over cross slide: 280 mm, spindle bore: 52 mm, turning diameter: 420 mm, center height: 210 mm, turning length: 1,000 mm, total length: 2,300 mm, total width: 1,300 mm, total height: 1,700 mm, spindle speed (max.): 1,500 rpm, spindle speed (min.): 33 rpm, quill mount: MK 4, Machine Equipment / Highlights Heidenhain ND 780 digital position display Crjdpfxsxqpwks Addsk Röhm 3-jaw chuck, Ø 250 mm Multifix quick-change tool holder Coolant system for efficient machining Chuck guard for increased safety Chip guard rear wall for a clean working environment Year of manufacture: 1981

Condition: good (used), L+Z lathe ERNAULT-SOMUA Cholet 435 Csdpfxexy Uavs Addsrk

Condition: excellent (used), Year of construction: 2004, We are offering an exceptionally high-quality precision lathe. Within its class, this is likely the best German lathe ever built. BOEHRINGER Precision Lathe Model DUE 500 Year of manufacture: 2004, including CE certification and central lubrication Machine No.: T1022.2027-00 Center height: 240 mm Swing diameter over bed: 500 mm Swing diameter over cross slide: 285 mm Center distance: approx. 1,200 mm Effective turning length: approx. 1,000 mm Bar capacity: 62 mm Spindle nose: DIN 55027 Size 6 Csdpsw Rdthofx Addork Spindle bore: 100 mm Drive power: 11 kW Maximum torque: 2,000 Nm 24 spindle speeds: 11.2 – 2,240 rpm 60 cross feeds: 0.03 – 28 mm/rev 60 longitudinal feeds: 0.06 – 56 mm/rev Tailstock quill stroke: 190 mm Tailstock taper: MK 5 Machine footprint (LxW): approx. 4,000 x 1,525 mm Weight: approx. 4,300 kg Accessories: - HEIDENHAIN 3-axis digital readout - Central lubrication system - Electrically interlocked chuck guard - Coolant system - Chip protection rear panel - Röhm chuck, T 250 mm, with various jaws - Telescopic cover for lead and feed screw, support to bed - Machine lamp - Multifix C + 4 quick-change tool holders - Live center - Operating manual - Circuit diagram - Rapid traverse in longitudinal and cross slides Condition: The machine is in very good technical and visual condition. Backlash on cross slide approx. 0.3 mm, on compound slide approx. 0.15 mm Spindle nose runout approx. 0.006 mm Bed geometry: deviation approx. 0.01 mm over approx. 750 mm bed length (measured on flat guideway towards chuck using dial indicator) The following parts have been renewed: - Oil change - New hoses for central lubrication - New wipers - Key for operating lever replaced - Locking pin for interlock replaced Price is net, ex stock, loaded free of charge. Delivery by company truck can be arranged at extra cost.

Condition: like new (used), – Distance between centres 910 mm – Swing over bed 300 mm – Swing over gap 430 mm – Swing over cross slide 180 mm – Spindle bore 40 mm Credpfx Aoxz S Umjddek – 75/1400 rpm – Digital speed display – Longitudinal and cross feed – Digital readout on two axes – Brake – Coolant system – Multifix quick-change toolpost with 4 tool holders – Lighting – Safety cover – Fixed steady rest – Travelling steady rest – 3-jaw chuck – 4-jaw chuck – Emergency stop – Documentation – 400V

Condition: good (used), Lead screw lathe Mondiale Galic 16 Year of manufacture 1974 Distance between centers: 1000 mm Height of centers: 200 mm 40 – 2000 rpm Geometrically revised 4 years ago 3-axis digital display Multifix B with 5 cassettes Crodpfxjvzx Hgs Addsk Coolant device Steady rest

Condition: new, Year of construction: 2023, functionality: fully functional, NEW PLANT / READY FOR OPERATION / IMMEDIATELY AVAILABLE HT 45 SM2 / SIEMENS - with driven tools CNC lathe for the complete machining of turned and milled parts with 2 spindles, 2 tool systems, 5 linear axes and 2 rotary axes, integrated spindle motors on main and counter and counter spindle (water-cooled), preloaded roller guides. Drive power: Main spindle - 15 kW Counter spindle - 15 kW Speed range: Main spindle 0 - 7000min-1 Counter spindle 0 - 7000min-1 Spindle connection (DIN 55026): Main spindle: KK 5 (max. bar capacity ø 45mm) Counter spindle: KK5 Includes: - Hollow clamping cylinder on the main spindle - Draw tube for main and counter spindle - Mechanical spindle brake (main/counter spindle) - Part ejector and flushing through the counter spindle - Control Sinumerik 840D-sl / OPERATE o emcoNNECT/APP-based user interface o 22" multi-touch display o IPC with 240 GB o SHOPTURN dialogue programming o USB interface o Network drive / Ethernet o 3D simulation o and much more - 2x 12-fold tool turret VDI 25 radial with directional logic for up to 2x 12 driven tool stations Swivel speed adjustable with feed switch! Performance data: -Max. 4kW at 2080 rpm -Torque constant 16 Nm -speed range 0-6000 rpm Credelxqf Nepfx Addek -C-axis for main and counter spindle -TRANSMIT software for simple C-axis programming - Chip conveyor with an ejection height of 1100mm programmable Type "hinged belt" ) - Coolant device integrated in the chip conveyor 2 pcs. High pressure pumps with 14 bar 2 pcs. flushing pumps with 3,7 bar Air gun with spiral hose - LED machine room light - Hydraulic power unit - Documentation

Condition: reconditioned (used), Year of construction: 1956, Lead and Feed Screw Lathe WEIPERT Cjdpfxew Ew D Dj Addork Year of manufacture: 1956 Spindle bore: 90 mm Centre distance: 3000 mm Swing over bed: 800 mm Swing over cross slide: 610 mm Swing in gap: 1120 mm Speed range: 7.5 – 475 rpm Comes with the following accessories: Multifix toolholder with 11 inserts Coolant system 3-jaw chuck 315 mm 3-jaw chuck 400 mm 3-jaw chuck 500 mm Faceplate 400 mm Faceplate 800 mm Faceplate 1000 mm Travelling steady Various turning tools (30 insert tools) 2 revolving centres 1 drill chuck Operating manual

Condition: ready for operation (used), Year of construction: 1977, Available immediately from insolvency: Credpfx Asxzdlkjddsk Stanko Lathes (longitudinal and transverse) Type 16 K 20 Year of manufacture: 1977 Retrofit and digital readout in 2012 Centre height: 200 mm Swing over bed: 400 mm Swing over cross slide: 220 mm Spindle bore: 55 mm Spindle speeds: 12.5 – 1600 rpm Drive: 7.5 kW Chuck Tailstock Coolant system Multifix tool holder with inserts Digital readout Steady rest (Lynette) Weight: 2700 kg Priced at EUR 2,500 plus VAT ex works

Condition: good (used), Lead and feed spindle lathe Matra SM-3000 Country of origin: Spain Turning diameter over bed 600 mm Turning diameter over support 370 mm Turning length 3000 mm Turning diameter in the crank 900 mm Length of the crank 280 mm Spindle bore 72 mm Speed range 17-1,652 rpm Spindle speed levels 36 Main motor, power 9/11 kW Rapid traverse longitudinal-transverse Tailstock MK5 Codpfx Aovq I Npeddjrk Machine weight approx. 4 t Dimensions (LxW) approx. 4800x1300mm Equipment/accessories: - Fixed steady rest with rollers/max. Workpiece diameter 220 mm - Coolant system - Bed stop - Röhm lathe chuck D500mm - Digital display 2-axis SINO - Multifix C base holder The machine is in very good, fully operational condition. Price net, free loading from warehouse

Condition: like new (used), Year of construction: 2024, – Distance between centers: 1000 mm – Swing over bed: 358 mm – Swing over cross slide: 502 mm – Swing over support: 179 mm Codpoxz Rg Uefx Addork – Spindle bore: 52 mm – 30/2300 rpm – Infinitely variable speed – Digital speed display – Longitudinal and cross feed – Digital readout on two axes (2-axis DRO) – Brake – Cooling – Multifix with 4 tool holders – Lighting – Safety guard – Fixed steady rest – Travelling steady rest – Three-jaw chuck – Four-jaw chuck – Emergency stop – Documentation – 400V

Condition: excellent (used), functionality: fully functional, Weiler Primus lead and feed screw lathe from training workshop !!! Technical data: >> Year of construction approx. 1985 >> center height 120 mm >> center distance 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm Crodpfx Adsu Aftgedjk >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck 160mm with 1 set of jaws >> 1 new three-jaw chuck 125mm with 2 sets of jaws >> Collet chuck device with collets from 1 mm to 20 mm 1 mm increasing >> Mulifix size A with 3 steel holders >> Fence >> Change wheels To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs smoothly even at high speeds. The Primus was used in a training workshop. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Condition: reconditioned (used), We are offering an exceptionally good precision lathe. The machine is probably the best German lathe that has been built in this class. BOEHRINGER precision lathe model DUE 800 Year of manufacture: 1984 Order no.: 04041.01-807 Center height: 400 mm Circulation diameter over bed: 820 mm Circulation diameter over facing slide: 515 mm Center width: approx. 2200 mm Effective turning length: approx. 2000 mm Bar passage: 128 mm Spindle head DIN55022 size 11 Drive power: 30 kW Max. Torque: 6300 Nm 24 Speeds: 7.1 - 1400 rpm 60 face feeds: 0.05 - 28 mm/rev 60 longitudinal feeds: 0.06 - 56 mm/rev Rapid traverse in longitudinal cross feed Motorized top support Tailstock quill stroke: 280 mm Tailstock taper: MK 6 Space requirement: LxWxH approx. 6700x2500x2250mm Weight: approx. 7500 kg Accessories: 3-axis digital readout HEIDENHAIN Coolant device; chip protection rear panel, power chuck autoblock 500 mm with clamping jaws, roller conveyor cover for lead screw support to bed, machine light, chip conveyor, Parat basic holder incl. 11 holders, suction unit, 3-jaw steady rest with roller inserts (moving), emergency stop, chuck key, moving center point, operating instructions Condition: Csdpfxsrt T S Rs Adderk The machine is in very good technical and optical condition. Backlash in the top slide 0.1 mm and face slide 0.15 mm The geometry of the machine is also very good (was checked with a dial gauge) Measured on the flat track guide with dial gauge in the direction of the lathe chuck Bed wiper replaced, gearbox input shaft axial play compensated and bearings replaced, drive pins on motor/gearbox side replaced, shaft seals on lock case replaced, various bearings replaced The machine can be demonstrated under power. Functional videos can also be sent on request.

Condition: excellent (used), functionality: fully functional, Weiler Primus guide and spindle lathe from the training workshop!!! Technical data: >> Year of manufacture approx. 1985 Machine no. 1191 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear stages >> Spindle passage 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg Crsdpjvtp Edofx Addok >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 x three-jaw chuck 125 mm with 2 sets of jaws >> Collet device with Collets 18 pieces >> Mulifix size A with 3 steel holders >> Stop >> Electric spindle protection About the machine: A Weiler Primus guide and pull spindle lathe is offered in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs quietly even at high speeds. The Primus was in a training workshop. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site with power on and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus GS guide and feed spindle lathe in very good original condition! Technical specifications: >> Year of manufacture approx. 1992 Machine no. 4549 Csdpfxswkh Abo Addjrk >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle bore 23 mm >> Short taper spindle head DIN 4 >> Tailstock MT 2 >> Feed rates from 0.03 to 0.15 mm/rev >> Possible thread sizes: metric, inch, module, and diametrical pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Switchable spindle brake >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> New collet chuck system, new collets from 3 to 25 mm >> 1 piece Three-jaw chuck with 2 sets of jaws >> Mulifix size A with 2 tool holders About the machine: Offered is a Weiler Primus GS guide and feed spindle lathe in very good original condition. The machine is fully functional. All slides run very smoothly and evenly. The bed guides are in excellent condition. The Weiler runs very quietly even at high speeds. The Primus was used in a training facility. This newer generation of Weiler lathes is very user-friendly and can produce surfaces that look as if they were ground. Take advantage of the opportunity to view this machine on-site with power on and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus GS lead and feed screw lathe 3 axis digital readout Easson- ES8 from training workshop Super condition !!! Technical data: >> Year of construction approx. 1990 Machine no. 3768 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head DIN 4 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 3-axis digital display from Easson ES8 >> collet chuck device from 1 to 20 mm collets 1 mm rising with holder and draw tube >> 1 three-jaw chuck with 2 sets of jaws >> 1 four-jaw chuck with 2 sets of jaws >> Mulifix size A with 3 steel holders >> Bed stop Crjdpfxevkfhpe Addsk >> Turning device To the machine : We are offering a Weiler Primus lathe built around 1990 in excellent condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The bed guides are in very good condition. The Weiler runs smoothly even at high speeds. The machine comes from a training workshop of a large company. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus LZ/G lead and feed screw lathe in special paint finish light gray !!! Technical data: >> Year of construction ca.1990 Machine-No.3150 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> spindle passage 23 mm >> Short taper spindle head DIN 4 Crsdpfx Adsvivmysdek >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Switchable spindle brake >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck NEW 125mm with 2 sets of jaws >> Mulifix size A with 2 steel holders >> collet chuck device new with collets from 3 to 26mm 1 mm increasing new >> To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run smoothly and evenly. The bed guides are in very good condition. The Primus was used in a training company. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see the condition for yourself.

Condition: excellent (used), Year of construction: 1997, functionality: fully functional, Weiler precision lathe model Condor B, lead and feed screw lathe with brand new K&C 3-axis digital readout, CE compliant! Technical data: >> Machine No. 2442, year of manufacture 1997 >> Centre height: 165 mm >> Centre distance: 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore: 40 mm >> Camlock spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock: MT 3 >> Feeds: from 0.015 to 0.46 mm/rev >> Thread cutting: metric, imperial, module and diametral pitch threads possible >> Metric thread pitches: 0.18 to 28 mm >> Weight: approx. 1100 kg >> Spindle brake, selectable >> Length: 1.83 m, height: 1.29 m, depth: 0.88 m Equipment and features: >> New K&C 3-axis digital readout, 12-month manufacturer's warranty, supplied with operating manual Features: mm/inch switching, selectable ABS/INC coordinates, value halving function, reference mark, tool memory for 200 tools, taper calculation, radius/diameter display, quick zeroing, count direction switching >> 1 x brand new 160 mm 3-jaw chuck with 2 sets of jaws >> 1 x 200 mm 4-jaw chuck with 1 set of jaws >> New collet chuck system and new collets from 3 to 25 mm in 1 mm increments Credpfoxcuazox Addjk >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle guard >> Rear splash guard >> Machine feet Safety features: electronic spindle guard, 2 emergency stop buttons, changewheel box with safety interlock, spindle brake About the machine: Offered here is a Weiler Condor in very good condition. The machine is, of course, fully functional. A very robust and powerful machine. The new K&C 3-axis digital readout makes work easier and more precise. The machine has been electrically and mechanically checked by us. A complete oil change has been carried out. This newer generation of Weiler lathes is very user-friendly. Take advantage of the opportunity to inspect and test this machine under power on site.

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, Weiler Primus VC Precision Centre Lathe 3-axis Digital Readout K&C NEW with VC Drive, Stepless Speed Adjustment, and CE Compliance, Very Good Condition Technical Data: >> Year of manufacture: 2003, Machine No. 646 >> Centre height: 140 mm >> Centre distance: 500 mm >> Spindle speeds: up to 4000 rpm, stepless >> Spindle bore: 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock Morse taper 3 >> Feeds: from 0.02 to 0.63 mm/rev >> Thread types: Metric, Inch, Module, and Diametral Pitch >> Metric thread pitches: from 0.25 to 8 mm >> Weight: approx. 800 kg >> Spindle brake can be activated >> Machine dimensions approx. 1.4 m x 1.55 m x 0.95 m Accessories and Equipment: >> 3-axis Digital Readout K&C NEW >> Collet chuck system with collets from 3 to 26 mm, new, 1 mm increments, NEW >> 160 mm 3-jaw chuck with 2 sets of jaws >> Multifix size A with 2 toolholders >> Electric chip guard >> Machine feet >> Splash guard Cjdpfjw Idllex Addjrk About the Machine: This offer is for a Weiler Primus VC lead and feed screw lathe, built in 2003 and in very good original condition. A very nice lathe with VC drive and stepless spindle speed control. The digital readout and scales from K&C are new. This newer generation of Weiler lathes is very user-friendly and can produce ground-like surface finishes. The K&C digital readout makes operation even easier and more precise. Take the opportunity to inspect this machine under power on site and be convinced of its condition.

Condition: excellent (used), Year of construction: 1987, functionality: fully functional, Weiler Precision Lathe Model Condor 81 Lead and Feed Spindle Lathe with 3-Axis Digital Display from K&C NEW Technical Data: >> Year of manufacture 1987 Machine No. 87 835 >> Center height 165 mm >> Center distance 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feeds from 0.015 to 0.46 mm/rev >> Possible threads: Metric, Inch, Module, and Diametral-Pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg Crjdpfjwrmuxex Addok >> Spindle brake switchable >> Length 1.83 m, Height 1.29 m, Depth 0.88 m Accessories and Equipment: >> 3-axis digital display from K&C new, 12 months manufacturer's warranty with operating manual Functions: Switch mm/inch, coordinate selection ABS/INC, halving of display value, reference mark, tool programming 200 pcs, taper calculation, radius/diameter, quick zeroing, reversing of count direction >> 1 piece 3-jaw chuck 160 mm NEW, 2 sets of jaws >> 1 piece 4-jaw chuck 160 mm, 1 set of jaws >> Collet equipment and new collets from 3 to 26 mm in 1 mm increments >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle guard >> Rear panel >> Coolant system >> Machine feet About the Machine: A used Weiler Condor 81 in very good condition is offered. The machine is, of course, fully functional and has been completely disassembled and repainted. A very robust and powerful machine. The new 3-axis digital display from K&C makes working even easier and more precise. The machine has been electrically and mechanically tested by us. A complete oil change was carried out. This newer generation of Weiler lathes is very user-friendly. Take the opportunity to view and test this machine on site under power.

Condition: excellent (used), Year of construction: 1991, functionality: fully functional, Weiler Center Lathe Model Condor B Guide & Feed Shaft Lathe with 3-Axis Digital Readout by K&C NEW from Training Workshop!! Technical Data: >> Machine No. 91-1814, Year of manufacture: 1991 >> Center height: 165 mm >> Distance between centers: 750 mm >> Spindle speeds: from 22 to 2,800 rpm >> Spindle bore: 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet locking >> Tailstock: MT 3 >> Feeds: from 0.015 to 0.46 mm/rev >> Threads possible: Metric, Imperial, Module, and Diametral Pitch >> Metric thread leads: from 0.18 to 28 mm >> Weight: approx. 1,100 kg >> Spindle brake switchable >> Dimensions (L x H x D): 1.83 m x 1.29 m x 0.88 m Scope of Delivery and Features: >> NEW 3-axis digital readout from K&C, 12-month manufacturer's warranty with operating manual Functions: mm/inch switch, ABS/INC coordinate selection, display value halving, reference mark, tool programming for 200 items, taper calculation, radius/diameter display, quick zeroing, counting direction reversal >> 1 pc. NEW 160 mm 3-jaw chuck, 2 sets of jaws >> 1 pc. 160 mm 4-jaw chuck, 1 set of jaws >> NEW collet chuck and NEW collets from 2 to 24 mm, incremented by 1 mm Codow Nw Dqspfx Addsrk >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle safety guard >> Rear splash guard >> Fixed steady rest >> Machine feet Safety features: electronic spindle guard, 2 emergency stop switches, change gear cover with limit switch, spindle brake About the machine: We are offering a Weiler Condor in very good condition. The machine is, of course, fully operational. It is a very robust and powerful lathe. The brand new 3-axis digital readout from K&C makes operation even easier and more precise. The machine has been electrically and mechanically tested by us. A complete oil change has been performed. This newer generation of Weiler lathes is very user-friendly. Take the opportunity to view and test this machine under power at our premises.