Used Hydraulic Drawing Press for sale (27,831)

Condition: used, Year of construction: 1966, Press force: 200 t Stroke: 600 mm Frame width: 1100 mm Shut height (stroke up): 1100 mm Table area: 1000 x 1000 mm Cushion force in table: 63 t Cushion stroke in table: 250 mm Fsdpfszyniwjx Aatepl Cushion area in table: 800 x 750 mm Table height above floor: 800 mm Ram area: 1000 x 1000 mm

Condition: ready for operation (used), functionality: fully functional, plate length 121cm plate width in widest place 112cm span between plates 30cm pump motor power 1,5kW piston diameter 156mm dimensions: Fsdpfx Aaey N Rgyotjpl length 183cm width 95cm height 188cm

Condition: good (used), Year of construction: 1991, We are selling our Hydrap 160-ton press. The system is only available for sale as a complete unit. Operating hours: 20,242 Condition: good Inspection is possible and welcome. Fpodpfx Aetu Szlsatjl Location: Szügy / Hungary

Year of construction: 1961, condition: ready for operation (used), A hydraulic single-column C-frame press Müller is available. Press force: 63t, stroke: 560mm, throat depth: 325mm, installation height: 700mm, table dimensions X/Y: 640mm/640mm, ram surface: 560mm/560mm, machine dimensions X/Y/Z: approx. 2000mm/1200mm/3100mm, weight: approx. 7500kg. The machine has a motor malfunction. An on-site inspection is possible. Fjdpoy Rtg Eefx Aatjpl

Condition: excellent (used), Year of construction: 1986, functionality: fully functional, pressing force: 40 t, stroke length: 500 mm, operating speed: 100 mm/s, reverse speed: 450 mm/s, table width: 630 mm, table length: 500 mm, ram plate width: 450 mm, ram plate length: 380 mm, oil tank capacity: 300 l, total length: 1,150 mm, total width: 1,750 mm, total height: 3,050 mm, overall weight: 3,200 kg, distance between stands: 800 mm, Equipment: documentation/manual, Hydraulic press PYE 40 S1/M with ejector. Year of manufacture 1986. Manufacturer VEB Wema Zeulenroda (Germany). Machine after general overhaul. Piston seal replaced. Fedjwbt Uqepfx Aatepl Parameters: Maximum pressing force 40 tons. Working pressure 16 MPa. Upper table 380 x 450 mm. Lower table 500 x 630 mm. Clearance 800 mm. Cylinder stroke 500 mm. Down speed 100 mm/sec. Up speed 450 mm/sec. Ejector stroke 200 mm. Ejector force 16 tons. Power demand 13 kW. Weight 3180 kg. Height 3050mm, Length 1750mm, Width 1150mm. The technical condition of the machine is very good. The machine has been overhauled. It is possible to inspect and check the machine in motion.

Year of construction: 1994, condition: ready for operation (used), Connected load: 12kW, length: 1770mm, width: 1250mm, height: 3700mm, weight: 13.2t, operational hours counter: 39,671h, with documentation, an inspection is possible. Fodjnxk I Repfx Aatspl

Condition: excellent (used), For sale: a professional pneumatic-hydraulic press by Mäder with a maximum pressing force of 100 kN (approximately 10 tons). The machine is designed for industrial applications, including pressing, assembly, stamping, crimping, straightening, and other workshop and production tasks. The press utilizes compressed air and a pneumatic-hydraulic system. It is equipped with foot pedal control for easy operation during work. Technical specifications: Fpjdpfx Aajzucxcjtel Manufacturer: Mäder Type: pneumatic-hydraulic press Pressing force: 100 kN / approx. 10 tons Operating pressure: 6 bar Total stroke: 50 mm Hydraulic stroke: 5 or 10 mm – depending on the version Frame overhang: approx. 300 mm Maximum working clearance: approx. 200–270 mm, adjustable Work table dimensions: approx. 310 × 220 mm T-slot width: 16 mm Mounting hole in the ram: Ø20 H7 × 34 mm deep Ram diameter: Ø40 mm Weight of the press itself: approx. 311 kg Working medium: filtered compressed air Noise level: below 75 dB Control: foot pedal The machine is sold with the table shown in the pictures.

Condition: new, pressing force: 200 t, DURENDUS 200 T Deep Drawing Press – Double Column Press – 900 × 900 mm Table, 80 T Drawing Cushion The machine shown here was already built and delivered to a customer's order. We can manufacture a new machine of this model for you at short notice – including individual options tailored to your requirements. This is a hydraulic deep drawing press with integrated drawing cushion function designed for forming processes, drawing operations, and precise sheet metal processing. Base price: €76,000 net Options (upon request): The options listed are based on completed customer projects and allow targeted adaptation of the machine to your specific application. The basic version offers a functional standard configuration – in practice, it is usually enhanced with additional features and specifically configured to project requirements. * T-slots and holes to customer specification * Adaptation of stroke, installation height, and press force range * Extended drawing cushion configuration * Customized control modifications * Enhanced safety and monitoring systems ==== Technical Data + Information: ==== General Information * Design: Double column press * Press force: 40–200 t (adjustable) * Total weight: approx. 5,500 kg * Overall dimensions (W × D × H): 2,370 × 1,300 × 3,300 mm ==== Working Area * Table size: 900 × 900 mm * Ram area: 900 × 900 mm * Installation height: max. 800 mm ==== Table & Ram * Table height: 1,000 mm * Ram stroke: 0–500 mm (adjustable) * Column guide: 4 columns Ø 120 mm ==== Speeds * Pressing speed: 4–10 mm/s * Idle speed: 10 mm/s * Return speed: 16 mm/s * Drawing cushion speed: 20 mm/s ==== Hydraulics & Drive Fsdpfx Aoyzf A Hsatspl * Operating pressure: max. 260 bar * Pump capacity: 70 l/min * Servo motor power: 15 kW * Pressure accuracy: ±5 bar * Hydraulic system with air cooling and oil monitoring ==== Control & Operation * Two-hand operation * Mode selector switch (key switch) * Modes: setup, manual cycle * Electrical connection: 400 V / 50 Hz * Total connected load: approx. 20 kW ==== Equipment * Drawing cushion: 30–80 t, stroke 200 mm * CE-compliant design * Safety limit switches * Hydraulic interlock * Control cabinet IP54 with brand components (SIEMENS, ALLEN BRADLEY, SICK) * Two-layer coating according to RAL colors ===== Deep drawing, sheet metal forming, forming technology, manufacture of drawn parts, series production, metalworking Deep drawing press, hydraulic press, double column press, drawing cushion press, forming press, sheet metal processing press Are you looking for a hydraulic press tailored to your application? Contact us for an individualized quotation. Our hydraulic presses are manufactured in accordance with German machinery directives, as well as European Machinery Directive (Directive 2006/42/EC), EC standards, and EU safety regulations.

Condition: new, Year of construction: 2026, machine/vehicle number: 06-26-005, functionality: fully functional, power: 17 kW (23.11 HP), input voltage: 400 V, type of input current: three-phase, pressing force: 160 t, stroke length: 500 mm, operating speed: 200 mm/s, reverse speed: 125 mm/s, table width: 900 mm, table length: 630 mm, throat depth: 360 mm, ram plate width: 750 mm, ram plate length: 450 mm, distance table to ram: 800 mm, total length: 2,200 mm, total width: 1,250 mm, total height: 3,500 mm, overall weight: 7,000 kg, year of last overhaul: 2026, controller manufacturer: SIEMENS, Equipment: CE marking, documentation/manual, safety light barrier, Hydraulic single-column press PYE 160 S1/M >completely overhauled / CE marking with  24 months warranty< from the manufacturer ZEULENRODA PRESSTECHNIK Hydraulic press for forming and assembly operations, pressing force 160 t Complete overhaul with CE conformity Ram stroke: 500 mm Clamping plate, press table: 900 x 580 mm with customer-specific clamping arrangement One-piece C-frame press in steel welded construction Newly manufactured table and ram plate according to customer requirements! Ram plate, twist-proof 3-sided protective guard, on the operator side via light curtain, on the side via sliding guard elements SIEMENS control system -new- Conversion to electronic stroke measuring system Remote maintenance ----- Further services, plant retrofit Control / Operation: • Rapid traverse function • USB interface for data exchange • Touchscreen / visualization SIEMENS • Two-hand control unit with two-channel monitoring of the two-hand synchronous circuit on the press table, Fsdpfx Ajzf Ht Seatopl (incl. 5m cable) • Limit switches for stroke adjustment are replaced by initiators • Monitoring of the initial stroke after completion • Replacement of the existing 60-V DC solenoids on the pilot control valves with 24-V DC solenoids, including the necessary intermediate plates • The press has an electronic stroke measuring system (including teach-in function and display of the current ram position). This eliminates the mechanical cam switching mechanism. Hydraulic system • Hydraulic safety block for monitoring the closing movement on the main cylinder • Position-monitored directional control valve for the up and down movement of the ram • Replacement of the motors of the main and control pump • Replacement of the seals on the main cylinder • Fine filter with contamination indicator • All installation and piping work New documentation including CE declaration of conformity Delivery time / Implementation time: approx. 5 months

Condition: excellent (used), Year of construction: 1995, functionality: fully functional, Hydraulic Frame Press HESS LUX 2000 The machine is fully operational and in good condition Maximum working dimensions: 4300 x 2600 mm Fedpfx Aexl Dv Djatjpl 3 top and 3 side cylinders Electric dimension adjustment from the control panel.

Condition: ready for operation (used), Year of construction: 2010, machine/vehicle number: 33407, functionality: fully functional, power: 37 kW (50.31 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, pressing force: 220 t, stroke length: 300 mm, operating speed: 21 mm/s, reverse speed: 200 mm/s, table length: 3,050 mm, throat depth: 400 mm, ram plate length: 3,000 mm, distance table to ram: 570 mm, clearance between the columns: 2,600 mm, oil tank capacity: 350 l, total length: 5,700 mm, total width: 2,100 mm, total height: 3,685 mm, overall weight: 14,500 kg, Equipment: CE marking, documentation/manual, safety light barrier, Technical specifications Force: 2200 kN Working length: 3000 mm Distance between uprights: 2600 mm Stroke: 300 mm Distance table – ram: 570 mm Gap: 400 mm Fpedpfszkxqmox Aatjl Turbo PP5400 Approach speed: 120 mm/s Working speed: 21 mm/s Return speed: 200 mm/s Weight: 13500 kg Motor: 37 kW Oil: 350 L Weight: 14500 kg LxWxH: 5700 x 2100 x 3685 mm Table: PP8170 V-axis  EFL 130 PP8303 Upgrade 2026  Top tool clamping: PP3090 – Wila  Hydraulic top tool clamping: PP3100  PP3160 hydraulic clamping V-dies  Back gauge: PP8251 XRZ modules: X1000  Security; CE: PP3580 – lasersafe  PP8402 T1 T2

Condition: refurbished (used), Single-column hydraulic press (completely overhauled) PYE 160 S1M - Pressing force: 1600 kN - Installation height: 800 mm - Stroke: 500 mm - Speed: downwards 200 mm/s - Draw cushion selectable: 630 kN, stroke: 200 mm Fsdpfx Asycl Hgoatopl - Drive: 17 kW - Dimensions: 3500 x 2000 x 1200 mm - new control system, new switch cabinet, light curtain (1-stroke, 2-stroke, safety), new hydraulics, - new seals, paint finish as requested - new UVV safety inspection

Condition: excellent (used), functionality: fully functional, RÖCHER conversion 1991 (formerly SCHÖN) Pressing force: 1,600 kN Ram stroke: 160 mm Table dimensions: 850 x 650 mm Fpodsx Sw Iiopfx Aatjl Light curtain control system Next mandatory inspection: February 26 Clamping pin lock in the ram Rapid approach speed: 274 mm/s Working speed: 20/10 mm/s Return speed: 273 mm/s Drive power: 30 kW Operating voltage: 380 Volt/50 Hz Max. fuse rating: 100 A

Condition: used, Heavy-duty hydraulic hole-press, perforated panel press or gluing press for gluing or securing workpieces such as frames, panels, windows or doors. Fpedpfx Ajzryy Ssatsl Technical data: - Cylinders: 6 - Hold-down units: 3 - Pressing area: 260 x 145 cm

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, type of input current: three-phase, pressing force: 5 t, operating speed: 300 mm/s, table width: 450 mm, table length: 320 mm, throat depth: 180 mm, oil tank capacity: 9 l, overall weight: 270 kg, Hydraulic Press Atsugi AP-5-KL Used Load Range: 20-50 (kN) Stroke (mm): 150 Lower Speed ​​(Approach Fast Speed: 350 (mm/s) Lower Speed ​​(Under Pressure Slow Speed: 36mm/s Rise Speed ​​250 (mm/s) Working Area Open Height: 250mm Open Depth: 180mm Table Size: 450x50mm Motor Specification 3 Phase AC200V 4P 1.5KW Two-Hand Operation . Mobile Worktable Fuel Oil / Quantity Daphni Hydraulic 46/9L Total Weight (kg) 270 Body Size ​ Height (mm) 986 Width (mm) 485 Depth (mm) 920 Fsdpfx Aasvbdpyotjpl

Condition: used, Year of construction: 1981, USED ALUMINIUM PROFILE PRODUCTION LINE GENERAL INFORMATION Equipment: Aluminium Extrusion Press Manufacturer: Youngstown (USA) Press Capacity: 1,650 Metric Tons Press Type: Horizontal Hydraulic, Direct Extrusion Year: Unknown (1980s) Refurbished: 1999 Condition: Under Power Availability: Immediate 1. INDUCTION HEATING SYSTEM - Make: Local - Control: PLC (LS Master-K80) - Built in: 1999 - Rated Power: 200 kW - Loader included 2. EXTRUSION PRESS - Rated Extrusion Force: 1,650 Tons - Main Ram Stroke: 1,200 mm - Maximum Extrusion Speed: 15 mm/sec - Maximum Extrusion Pressure: 20–25 MPa Control System - PLC System: LS XGK - HMI: Touch Screen Operator Panel - Control Modes: Manual / Semi-Automatic / Automatic - Process Control: Extrusion Pressure & Speed Control Hydraulic System - Main Working Pressure: 20–25 MPa - Main Motor Power: 2 × 132 kW - Hydraulic Pumps: 2 × Kawasaki LZ-500-110R1 (600 L/min) - Oil Tank Capacity: 8,000 Liters - Oil Cooling Pump: 120 L/min Billet & Container - Container Cylinder: Ø203.2 mm - Container Heating: Induction - Billet Diameter: 150 mm - Billet Length: 550 mm Die & Tooling - Maximum Die Diameter: 230 mm - Die Change System: Manual - Die Heater 3. RUN-OUT TABLE - Length: 40 m - Cooling: Water / Air - Profile Support Rollers 4. PULLER - Speed synchronized with extrusion - Hydraulic gripping system 5. SHEAR - Cylinder: Ø155 mm Fjdpezy H Rmjfx Aatjpl - Stroke: 571.5 mm 6. COOLING BED - Length: 40 m 7. STRETCHER - Capacity: 25 Tons - Length: 30 m 8. CUTTING SAW 9. PACKING SYSTEM - Profile Stacking - Bundle Tying FLOOR SPACE 20 × 60 m

Condition: like new (used), Year of construction: 2022, functionality: fully functional, Equipment: CE marking, documentation/manual, Capacity: 4050 mm x 175 Ton Distance between frames: 3600 mm Stroke: 265 mm Control: DURMA DT15 (3D Touch Screen) Serial No.: 73362219436 Dimensions: 5200 x 1900 mm Fsdoyrdgqopfx Aatspl Height: 2930 mm Weight: 12,750 kg

Condition: good (used), Year of construction: 1986, machine/vehicle number: 057-016-47, Offer 26185 Technical specifications: - Maximum pressing force: 160 t - Maximum ram stroke: approx. 500 mm - Average working speed: approx. 92 mm/s - Return speed: 125 mm/s - Installation height: approx. 1000 mm - Overhang to center of ram: 360 mm - Ram mounting pin: 40 mm - Table size: 900 x 630 mm - Table bore/opening: 220 mm - Table height above floor: 720 mm Fpedpfx Aaszn H Rvetol - Oil capacity: approx. 200 liters - Drive: 400 V / 17 kW - Space requirement: approx. W 1150 x H 3600 x D 1850 mm - Weight: approx. 7500 kg

Condition: good (used), Year of construction: 1995, power: 22 kW (29.91 HP), pressing force: 120 t, stroke length: 400 mm, table width: 1,250 mm, table length: 1,000 mm, table height: 950 mm, retraction force: 5 t, total length: 2,100 mm, total width: 2,050 mm, total height: 3,800 mm, control cabinet height: 1,900 mm, control cabinet length: 600 mm, control cabinet width: 500 mm, installation height: 900 mm, Equipment: safety light barrier, Deep drawing press, press power 120 to, stroke 400 mm, distance between tabels 900 mm, with oil cooler, light security bareer, dimension 2100x2050x3800 mm, weight ca. 13400 kgs Fsdoycin Uopfx Aatepl

Condition: used, Year of construction: 1997, Press force: 40 t Stroke: 620 mm Throat depth: 280 mm Shut height (stroke up): 830 mm Table area: 620 x 520 mm Fpsdjzypmwopfx Aatjl Table opening: 150 mm Table height above floor: 600 mm Ram area: 150 mm Downstroke speed: 120 mm/s Upstroke speed: 30 - 450 mm/s

Condition: good (used), Year of construction: 1984, machine/vehicle number: 054-008-212, Offer 25272 Technical data: - Max. pressing force: 25 t - Max. ram stroke: 500 mm - Stroke speed: 0 – 2.4 m/min - Return speed: 0 – 12 m/min - Installation height: 800 mm - Throat depth to ram center: 360 mm - Ram clamping area: 440 x 360 mm - Ram mounting shank: 40 mm - Table size: 630 x 500 mm - Table bore/opening: 180 mm - Electric foot switch - Two-hand control panel - Drive: 400 V / 8.75 kW - Required space approx.: W 800 x H 2750 x D 1150 mm - Weight approx.: 2000 kg Fedpfx Aaey Ewtretopl

Condition: good (used), Year of construction: 1988, machine/vehicle number: 053-019/35, Offer 24591 Fpodpfx Aowd Nybsatjl Technical specifications: - Maximum press force 25 t - Maximum ram stroke 500 mm - Stroke speed 0 - 40 mm/s - Return stroke 0 - 200 m/min - Installation height 800 mm - Throat to ram center 360 mm - Ram clamping area 440 x 360 mm - Ram clamping pin 40 mm - Table size 630 x 500 mm - Table height above floor 710 mm - Deep drawing force 10 t - Maximum deep drawing depth 160 mm - Drive 400 V / 4 kW - Space requirement approx. W 800 x H 2720 x D 1150 mm - Weight approx. 2500 kg

Condition: like new (used), Year of construction: 1991, input voltage: 200 V, pressing force: 3 t, operating speed: 47 mm/s, table width: 410 mm, table length: 320 mm, throat depth: 125 mm, oil tank capacity: 6 l, total length: 735 mm, total width: 505 mm, total height: 987 mm, for sale in new condition ATSUGI 3 ton Hydraulic Press Atsugi Model AP-3-M Used load range: 6-30 (kN) Stroke: 150mm Down speed: 46.7 (mm/s) Up speed 56.7 (mm/s) two-handed operation mobile workbench Operating area: Open height: 250mm open depth: 125mm table size: 410x320mm Motor specification 3 phase AC200V 4P 1.5KW two-handed operation . mobile workbench Fodov Sd Anspfx Aatspl Operating oil / quantity: 6 Liter Total weight (kg) 200 Body size ​ Height (mm) 987 width (mm) 505 Depth (mm) 735

Condition: new, Year of construction: 2025, pressing force: 300 t, stroke length: 800 mm, table width: 1,000 mm, table length: 1,000 mm, clearance between the columns: 1,000 mm, retraction force: 100 t, operating pressure: 250 bar, Equipment: documentation/manual, safety light barrier, CRONOSSTECH 300 / 100 Ton Four-Column Hydraulic Deep Drawing Press General Description The CRONOSSTECH 300 / 100 ton four-column hydraulic deep drawing press is a high-rigidity, four-column hydraulic press solution developed for metal forming, deep drawing, and precision pressing applications. Its St52 grade steel frame undergoes stress-relieving via vibration, ensuring stable parallelism and perpendicularity tolerances throughout the full stroke. The ram and bolster systems operate independently; stroke length and tonnage settings can be precisely controlled via the touch panel interface. Equipped with REXROTH or PARKER hydraulic components, an IE3 class motor, and PLC-controlled structure, the machine provides high efficiency and reliable operation. The automatic lubrication system and electronic filter contamination alerts minimize maintenance requirements. With a 300 / 100 ton capacity, this model is an ideal industrial press solution for medium to high tonnage metal forming, deep drawing, and die applications. Key Advantages - High-rigidity four-column press frame - Independent stroke and tonnage adjustment for ram and bolster - Full control via touch panel - High precision and repeatability - Long lifespan, low maintenance design Fields of Application - Metal forming applications - Deep drawing operations - Die testing and production lines - Auxiliary pressing processes ⚙️ STANDARD AND TECHNICAL SPECIFICATIONS TYPE: Four-Column FRAME MATERIAL: St52 – ERDEMİR COLUMN SHAFT DIAMETER: Ø 90 mm – 4 pcs, induction-hardened chrome-plated shafts SLIDE BEARING: Bronze Zr14 CAPACITY (RAM): 300 Ton CAPACITY (BOLSTER): 100 Ton DISTANCE BETWEEN COLUMNS: 1000 × 1000 mm PARALLELISM TOLERANCE: 120 micron/m PERPENDICULARITY TOLERANCE: 60 micron/m STROKE (RAM): 800 mm STROKE (BOLSTER): 200 mm MIN. CLEARANCE: 100 mm MAX. CLEARANCE: 900 mm WELDING STRESS RELIEF: Vibration stress relief WELDING PRACTICE: TÜRK-AK accredited WPQR & WPS – EN ISO 15614-1:2017 (EN ISO 14731) MAX. WORKING PRESSURE: 250 Bar TOTAL MOTOR POWER: 30 kW – IE3 MAIN PUMP: 45 cm³ – REXROTH or PARKER MOVING TABLE FAST DESCENT SPEED: 150 mm/s FORMING SPEED: 12 mm/s RETURN SPEED: 170 mm/s BOLSTER TABLE FORWARD SPEED: 30 mm/s MAIN CYLINDER BORE: Ø 390 mm – Ck45 BOLSTER CYLINDER BORE: Ø 230 mm – Ck45 AUXILIARY BOOSTER CYLINDERS: 2 Units APPROX. PRESS DIMENSIONS: 4000 × 1450 × 1450 mm BOTTOM TABLE HEIGHT FROM FLOOR: 1300 mm FRONT CHARGE VALVE: NG 125 HYDRAULIC UNIT: REXROTH or PARKER COOLING SYSTEM: EMMEGI – CIESSE – PARKER OFF-LINE FILTRATION: REXROTH or PARKER Fpedpfxex N Unzs Aatol PLC: DELTA TOUCH PANEL: DELTA 7” SWITCHGEAR COMPONENTS: SIEMENS – SCHNEIDER APPROX. WEIGHT: 18 Ton Production Note This machine is manufactured in Turkey by CRONOSSTECH.

Condition: excellent (used), functionality: fully functional, Year of construction: 2020, power: 4 kW (5.44 HP), We are offering this very well-maintained Uniflex HM 325.2i_C.2_FD_MVA hose crimping machine with foot pedal, year of manufacture 2020. Model: HM 325.2i_C.2_FD_MVA Serial number: 60046 Voltage: 400 V Current: 15/8.5 A Power: 4.0 kW Frequency: 50/60 Hz Year of manufacture: 02/20 Fjdpfxjy Apdws Aatepl Price ex works. The machine must be collected either personally or via freight forwarding. Payment terms: 50% down payment / 50% upon collection – no cash payments! Payment by bank transfer only. Any warranty and liability are excluded. If you have any questions or require more information, please do not hesitate to send us a message.