Used Kellenberger for sale (86)

Condition: ready for operation (used), functionality: fully functional, center height: 125 mm, center width: 600 mm, grinding wheel diameter: 400 mm, grinding wheel width: 50 mm, grinding wheel bore: 127 mm, The motor and frequency inverter for the workpiece headstock have been replaced! Additionally, the control cabinet and wiring diagram have been renewed! TECHNICAL DETAILS Centre height: 125 mm (175 mm with riser blocks) Centre distance: 600 mm Grinding wheel diameter: 400 mm Grinding wheel width: 50 mm Grinding wheel bore: 127 mm Swivel range: 270° Workpiece headstock speed: 20 rpm to 400 rpm Spindle taper: 5 MT Tailstock taper: 3 MT Table swivel: 10° Table feed speed: up to 6.0 m/min MACHINE DETAILS Cedpfx Aeyb R Nqefpepu External grinding wheel motor: 4.0 kW Workpiece spindle motor: 2.2 kW Dimensions & Weight Dimensions (L x W x H): 2,580 x 1,680 x 1,670 mm Machine weight approx.: 2,700 kg EQUIPMENT New control cabinet and new wiring diagram New motor and frequency inverter for the workpiece headstock 2-axis digital readout Coolant tank Geometry according to Kellenberger protocol Extensive accessories

Condition: ready for operation (used), Year of construction: 1995, functionality: fully functional, machine/vehicle number: 630005, center height: 305 mm, center width: 1,000 mm, travel distance X-axis: 350 mm, travel distance Z-axis: 1,160 mm, controller model: KELCO 90, TECHNICAL DETAILS Centre height: 225 mm / 305 mm Centre distance: 1,000 mm Travel Z-axis: 1,160 mm Travel X-axis: 350 mm Max. workpiece weight: 200 kg Workpiece diameter: 449 mm Left grinding wheel diameter: 500 mm Left grinding wheel width: 80 mm Left grinding wheel bore: 203 mm Right grinding wheel diameter: 400 mm Right grinding wheel width: 40 mm Right grinding wheel bore: 127 mm B-axis swiveling range: +30° / -190° Max. grinding wheel speed: 1,720 rpm Peripheral speed: 45 m/s Workpiece spindle speeds from: 5 rpm Workpiece spindle speeds up to: 500 rpm Spindle taper: Morse taper 5 (MT 5) Tailstock quill taper: 4 Morse (MT 4) Tailstock quill stroke: 50 mm Feed rate X-axis: 8 m/min Feed rate Z-axis: 16 m/min Cedpfoyhnrvsx Afpepu Max. table tilt: -1° / +11° MACHINE DETAILS Control: KELCO 90 Total power requirement: 25 kW Connection: 50 Hz, 3x 380 Volt Dimensions & Weight Machine dimensions (L x W x H): 2,850 x 2,200 x 2,100 mm Control cabinet dimensions (L x W x H): 550 x 450 x 900 mm Machine weight: approx. 6,000 kg EQUIPMENT 80 mm riser block Coolant system Automatic tool measurement KELSET Wheel dressing device Internal grinding device (without spindle) Set of flanges Set of grinding wheels Balancing arbor Lamp Magnetic chuck diameter (2x): 300 mm / 500 mm Electronic hand-held control panel

Condition: excellent (used), functionality: fully functional, KELLENBERGER PRECISION UNIVERSAL CYLINDRICAL GRINDING MACHINE MODEL: 1000 U YEAR OF MANUFACTURE: 2000 PARTIAL OVERHAUL: 2026 Centre height: 175 mm Grinding length: 1000 mm Equipment: - Standard accessories - Standard workpiece headstock MK5 with adapter flange DIN 55027, size 5 - Splash guard hood for the above - Tailstock with fine adjustment, MK4 - Internal grinding attachment with protective cover for grinding spindle D:80 mm for belt-driven spindles - FISCHER internal grinding spindle type HJN 842, incl. grinding mandrels (4 pieces, choice) - HJNZ 42 collet chuck - Oil mist lubricator for HJN spindles - STREULI magnetic paper band filter system, type: SPB 2 - Coolant supply through the workpiece spindle - HEIDENHAIN digital length measuring system on X and Z axes - Sine bar on the workpiece headstock incl. alignment arbor MK5 - Permanent magnetic chuck, D:200 mm - Three-jaw chuck, D:160 mm - Four-jaw chuck, D:160 mm - Collet attachment for Schaublin collets B32 - Set of B32 collets, D: 1.0–30.0 mm, increment 0.5 mm (59 pieces) - Dial indicator stop for table swivel with indicator 0.01 mm - Table fixed stop - Dressing stop for internal grinding Cjdeyf E Sujpfx Afpopu - LED machine lamp - Various grinding wheel flanges, left (2 pieces) - Pneumatic table load relief - Swiveling dressing device for external, face, or internal grinding operations - Set of vibration damping pads - New three-color paint finish (light grey RAL 7035 / blue RAL 5012 / dark grey RAL 7016) - New acceptance protocol according to KELLENBERGER standard - Documentation - CE conformity The machine is currently being overhauled, sample photos shown!

Condition: used, total width: 1,750 mm, total length: 2,260 mm, total height: 1,360 mm, Empty weight: 2.000 kg - Documentation available: Yes - CE certificate present: No - Drive system: Conventional - Grinder type: External grinding machine - Drive system: Hydraulic - Distance between centres [mm]: 750 - Centre height [mm]: 125 - Grinding diameter [mm]: 250 - Max. grinding wheel diameter [mm]: 350 - Max. grinding wheel thickness [mm]: 50 - X-axis travel [mm]: 900 - Swivel range [°]: 10 - Table width [mm]: 1160 - Table depth [mm]: 140 - Main spindle power [kW]: 3.5 Cpedpfx Ajyf Hvhjfpeu - Max. spindle speed [rpm]: 2850 - Transport dimensions: 2260mm x 1750mm x 1360mm (l x w x h) - Transport weight [kg]: 2000kg - Transport packages [pcs.]: 2 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: good (used), Year of construction: 1997, Ref. -No.: 10619 Manufacturer: KELLENBERGER Type: 600 U Nr. 35 Year of construction: 1997 Type of control: Konventionell Control: n/a Storage location: Halberstadt Country of origin: Switzerland Distance between center: 600 mm Center height (standard): 125 mm Height of centers by lifting work blocks head and tailstock: 175 - 250 mm Swing diameter with lifting blocks max.: 350 - 500 mm Cpedpeya Dayofx Afpsu Table swivel / each side: 10 ° Dwell time of the table reversal: 0- 5 Sec Diameter / width / hole: 250 x 13 x 76 mm Speeds of the grinding wheel spindle: 1500 / 1700 / 2200 / 3600 Swiveling grinding wheel head: 360° ° Cross movement of the grinding wheel head: 285 mm Quickly pulling the wheel head back and forth: 40 mm Intermittent injection for each reversal of the table: 0,001 - 0,03 mm / dia Working speeds continuously adjustable (normal / special): 20-400 / 10-400 Max. Grinding length: 900 mm

Condition: good (used), Year of construction: 2003, Ref. -No.: 10618 Manufacturer: KELLENBERGER Type: 600 U Nr. 33 Year of construction: 2003 Type of control: Konventionell Control: n/a Storage location: Halberstadt Country of origin: Switzerland Distance between center: 600 mm Center height (standard): 125 mm Height of centers by lifting work blocks head and tailstock: 175 - 250 mm Swing diameter with lifting blocks max.: 350 - 500 mm Table swivel / each side: 10 ° Dwell time of the table reversal: 0 - 5 Sec Diameter / width / hole: 250 x 13 x 76 mm Speeds of the grinding wheel spindle: 1500 / 1700 / 2200 / 3600 Swiveling grinding wheel head: 360 ° Cjdeya Dagjpfx Afpopu Cross movement of the grinding wheel head: 285 mm Quickly pulling the wheel head back and forth: 40 mm Intermittent injection for each reversal of the table: 0,001 - 0,03 mm / dia Micro-corrector of the feed, 1 division of the dial: 0,001 mm / Ø Working speeds continuously adjustable (normal / special): 20-400 / 10-400 Max. Grinding length: 900 mm

Condition: good (used), Year of construction: 2001, Ref. -No.: 10617 Manufacturer: KELLENBERGER Type: 600 U Nr. 36 Year of construction: 2001 Type of control: Konventionell Control: n/a Storage location: Halberstadt Country of origin: Switzerland Distance between center: 600 mm Center height (standard): 125 mm Height of centers by lifting work blocks head and tailstock: 175-250 mm Swing diameter with lifting blocks max.: 350 - 500 mm Table swivel / each side: 10 ° Dwell time of the table reversal: 0 -5 Sec Diameter / width / hole: 250 x 13 x 76 mm Speeds of the grinding wheel spindle: 360° Cross movement of the grinding wheel head: 285 mm Quickly pulling the wheel head back and forth: 40 mm Cpodpsya Daasfx Afpju Intermittent injection for each reversal of the table: 0,001 - 0,03 mm / dia Micro-corrector of the feed, 1 division of the dial: 0,001 mm / Ø Working speeds continuously adjustable (normal / special): 20 - 400 / 10-400 Max. Grinding length: 900 mm

Condition: excellent (used), Year of construction: 1997, grinding diameter 80 - 250 mm grinding length 600 mm centre height 175 mm longitudinal feed 750 mm workpiece turning speeds 6 - 600 U/min Cedjyb S Rcopfx Afpepu grinding spindle speed 1500 - 3600 U/min cross movement - autom. and by hand 320 mm Control Kelco 80 weight of the machine ca. 4,4 t dimensions of the machine ca. 3,1 x 2,1 x 2,0 m

Condition: used, Year of construction: 2003, Technical details: grinding diameter: 350 mm grinding length: 600 mm centre height: 175 mm grinding wheel hole diameter: 127 mm dimensions of grinding wheel: 400 x 50 mm grinding spindle speed: 1.500, 1.700, 2.200 1/min work piece spindle speed: 6 - 600 1/min max. workpiece weight between centres: 150 kg grinding head swivelling: -30 bis +120 Grad grinding head swivellable ° table swivelabel ° table adjustment - longitudinal: 905 mm automatic feed per table reverse control:: 0,001 - 0,030 mm feed - continual: 0 - 0,99 mm table speeds: 0 - 6 m/min taper in tailstock: MK 4 tailstock travel: 30 mm diameter of internal spindle: 80 mm spindle drive motor: 3,6 kW spindle cone: MK 5 total connected load: ca. 7,5 kW weight of the machine ca.: 2,3 t Csdpfxeya Ekmo Afpspu dimensions of the machine ca.: 3,2 x 2,1 m universal cylindrical grinding machine, internal grinding attachment incl. spindle, HEIDENHAIN DRO in 2 axis, balancing device ELASO EB 2000, ASYST APNC 400 NC-dressing and programming unit, cooland device incl. paperfilter, manuals (German language), a lot of accessories (grinding wheels (external+internal), steady, pusher dog, collets, chucks, balancing device, dresser...) MACHINE FROM TOOLSHOP, BARELY USED ! *

Year of construction: 1995, condition: ready for operation (used), overall weight: 6,000 kg, product length (max.): 3,600 mm, This KELLENBERGER Kel-Varia cylindrical grinding machine was manufactured in 1995. It features a Kellenberger Kelco 90 control system and a robust internal grinding device with a B-axis for a tiltable grinding head. The machine supports a tip height of 175 mm and a tip width of 1,000 mm, equipped with a belt filter system. Ideal for precision grinding tasks. Contact us for more information about this machine. • Capacity: Center height 175 mm; between centers 1000 mm • Configuration: Internal grinding device; B-axis tiltable grinding headGrinding head and B-axis • Grinding heads available: R, RS, UR • R head pivot: +30° • RS/UR heads, rotating part indexing: • Manual indexing: 180° to -190°, 2.5° steps • Automatic indexing: 180° to -90° (or -30°), 2.5° steps • B-axis (RS/UR heads): pivot +180° to -190° (some variants limited to about +30°); resolution 0.1"Workhead • Standard workhead (C-axis): pivot -30° to +120° • Spindle speed: up to 600 rpm (stepless) • Mounting taper: MK5; reduction sleeve MK5/MK4 • Adapter flange: MK5 / DIN 55027 size 5 • Torque capacity: 160 Nm • Max workpiece between centers: 150 kg • Workhead with rotating spindle: • C-axis pivot: -30° to +120° • Spindle speed: 5–500 rpm (stepless) • Mounting taper: MK5 • Torque capacity: 320 Nm (incl. clamping device) • Max workpiece between centers: 220 kgTailstock • Taper: MK4 • Quill stroke: 50 mm • Micro-adjust (option): ±150 µm (±0.006 in)Grinding wheels and internal grinding • UR head: • Left wheel max: 400 × 63 mm • Right wheel max (option): 400 × 50 mm • Max peripheral speed: 32 m/s • R head: • Wheel max: 500 × 100 mm • Max peripheral speed: 32 m/s with 7.5 kW motor; 45 m/s with 9.2 kW motor • RS head: • Wheel max: 500 × 80 mm • Max peripheral speed: 32 m/s with 7.5 kW motor; 45 m/s with 9.2 kW motor • Internal grinding (option/device on this machine): • Mounting bore for high-performance spindles (HJN): 80 mm • Mounting bore for high-frequency spindles (MFV): 120 mmAxes and tables • Z-axis (lower table): • Max speed: 15 m/min • Resolution: 0.1 µm • Travel (1000 mm between centers version): 1150 mm • Upper table swivel range (1000 mm between centers): 0 to +9° • X-axis (grinding slide): • Max travel: 320 mm • Max speed: 7.5 m/min • Resolution: 0.1 µmDrive motors • X-axis slide: 0.94 kW (2000 min⁻¹) • Z-axis table: 0.94 kW (2000 min⁻¹) • Indexing / B-axis: 0.63 kW (3000 min⁻¹) • Grinding spindle UR: 4.4 kW @ 50 Hz (3000 min⁻¹) / 5.2 kW @ 60 Hz (3600 min⁻¹) • Grinding spindle R/RS (7.5 kW version): 7.5 kW @ 50 Hz (1500 min⁻¹) / 9 kW @ 60 Hz (1800 min⁻¹) Csdpfx Ajybb T Tjfpspu • Grinding spindle R/RS (9.2 kW version): 9.2 kW @ 50 Hz (1500 min⁻¹) / 11 kW @ 60 Hz (1800 min⁻¹) • Workhead (standard & rotating): 3.1 kW (3000 min⁻¹) • Hydraulic pump: 0.37/0.44 kW (1500/1800 min⁻¹) • Hydrostatic pump: 0.37/0.44 kW (1500/1800 min⁻¹)Dimensions, weight, utilities (1000 mm between centers version) • Floor space (L × W): 3600 × 2000 mm • Weight: net 5000 kg; gross 6000 kg • Minimum air pressure: 4 bar • Noise emission: 70 dB(A) Additional equipment • Belt filter coolant system

Condition: used, Year of construction: 1987, functionality: fully functional, We offer this used CNC cylindrical grinding machine KELLENBERGER R 125 X 1000 CNC, year of manufacture 1987, currently located in Spain. Immediately available. Control: KELCO 40 – spindle with internal MK 5 taper and through bore 38.2 mm – grinding wheel diameter: 400–500 mm – speed range: 1720–1910 rpm – grinding wheel peripheral speed: 40–45 m/s – center height: 125 mm – center distance: 1000 mm. Cpsdpoyhddzsfx Afpsu

Year of construction: 1997, condition: ready for operation (used), number of axes: 4, This 4-axis KELLENBERGER Kel-Varia UR 175/1000 was manufactured in 1997. It features an internal grinding device with a tiltable B-axis and a C-axis for out-of-round grinding, complemented by a belt filter system. Consider the opportunity to buy this KELLENBERGER Kel-Varia UR 175/1000 cylindrical grinding machine. Contact us for more information. Additional equipment Cedpfxjx T Dg Ij Afpepu • Belt filter system Machine Benefits Technical Machine Benefits • Internal grinding device with b-axis for tiltable grinding head and c-axis for out-of-round grinding Extra Information Center height x center distance: 175 x 1,000 mm Complete with standard accessories, electrical equipment For three-phase current 3 x 400 volts, 50 Hz. Machine color: DARK GRAY NCS 7502B combined with BLUE NCS KEL-ASSIST 90 PLUS software package Internal grinding attachment with 80 mm diameter chuck Right-hand grinding wheel attachment, 400 x 50 mm diameter Oil mist lubrication device for HJN spindles Micro-adjustment on the tailstock Face-spiral three-jaw chuck, 160 mm diameter Dressing device on the upper table Pivoting diamond holder 9.5 mm MOVOMATIC lead-in sensor Set of vibration-damping pads Set of lubricant for initial filling CNC-controlled C-axis

Condition: used, Technical details: grinding length: 300 mm Codevc Aw Sopfx Afpjpu centre height: 175 mm swing diameter: 315 mm table clamping surface LxW: 1.800 x 200 mm control: Heidenhain Longitudinal adjustment of grinding unit on table max.: 1100 mm work piece spindle speed: 3steps/1500-2200 U/min feed continuous: 0,001-1 mm Max. travel x-axis: 300 weight of the machine ca.: 3,1 t dimension machine xH: 2,9 x 1,6 x 1,4 mm Swivel for right and left machining Automatic table reversal Tailstock: MK3 holder Operation: Manual control unit/foot switch Coolant: System with feed Heidenhain measuring device *

Condition: excellent (used), Kellenberger 1000U cylindrical grinding machine with many accessories available at a low price. This machine is in very good condition and is fully functional. It was purchased as a completely overhauled unit in 2019. Price greatly reduced!!!!! Cpedpfjwkt Eujx Afpou

Condition: used, Year of construction: 1995, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm Teilüberholte Maschine mit Messprotokoll nach Neumaschinentoleranz Cpjdjyatx Sjpfx Afpju NEUE Steuerung Eckelmann ENC mit BEMA Schleifsoftware KEL-ASSIST für Kelco 90 numerisch gesteuerte B-Achse Innnschleifrinrichtung Dia 80mm Schleifscheibe links Durchmesser 400mm Schleifscheibe rechts Durchmesser 300mm Innenschleifspindel HJN 828 hydraulischer Reitstock Mikroverstellung KEL SET Messsystem

Condition: used, Year of construction: 1997, 2 x cylindrical grinding machines Kellenberger type: kel varia, year of manufacture 1997 and 1995. Technical data and more pictures available on request. Csdpfx Ajx T A Iwofpspu

Condition: used, functionality: fully functional, For sale is a universal cylindrical grinding machine from the Strausser-kellenberger brand Technical data: Manufacturer: Strausak AG Maschinenfabrik (Switzerland) Cpjdpfx Aov E Ivfsfpou Model: 57U Voltage: 380V / 50 Hz Machine purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For further information or contact options, visit us on our website

Condition: excellent (used), machine/vehicle number: 31.207.011, Manufacturing origin Swiss Voltage 380/50/3 Netweight 3150 kg Dimensions 400x185x175cm Custom position 8460 TECHNICAL DATA Distance between centres 1000 mm Centres height 175 mm Cpjdpfeiwtm Sex Afpsu Wheelhead Wheel : diameter/width/bore 500 / 80 (100) / 203.0 mm Max width of wheel 80(100) mm Spindle speeds 1220,1360,1530 min-1 Table maximal travel 1100 mm Table, speed (variator, progressively adjustable) 0.02 to 6.0 m/min Workpiece headstock Swivel 360° speed (variator,progressive adjust) 20 min-1 to 400 min-1 Wheelhead motor 6 HP Total power 7 HP Max diameter of workpiece 249 mm Tailstock internal taper Morse 3 errors and omissions excepted-data given without obligation

Condition: refurbished (used), Year of construction: 2025, functionality: fully functional, machine/vehicle number: 1315/451, Completely overhauled: Mechanics, geometry, hydraulics, and electrical parts (checked and/or replaced) Wheelhead: Disassembled, parts cleaned, worn or defective components replaced, motor overhauled, bearings replaced, belts replaced, spindle disassembled, seals and O-rings replaced, adjustments made. Newly painted. Workhead: Disassembled, parts cleaned, worn or defective components replaced, motor overhauled, belts replaced. New spindle bearings. Newly painted. Tailstock: Disassembled, inspected, overhauled. Hydraulics: Disassembled, motor checked, hoses replaced, defective and worn parts replaced. Hydraulic block checked. X-axis: Disassembled, all worn parts such as O-rings, seals, segments, etc. replaced, hydraulic piston overhauled, table ground. Z-axis: Disassembled, table ground, worn or defective parts replaced, hydraulic piston overhauled, newly painted. Electrical cabinet: Completely checked, various relays replaced. Paintwork: Colors: White RAL 9003 and Grey RAL 7011 Geometry according to manufacturer's protocol. Various accessories checked and cleaned. Origin: CH Voltage: 380 / 50 / 3 Net weight: approx. 2,200 kg Customs tariff number: 8460.2920 TECHNICAL SPECIFICATIONS Nominal distance between centers: 600 mm Max. distance between centers (with extended headstock): 750 mm Center height, standard: 125 mm Center height with interchangeable pads for heads: 175–250 mm Max. workpiece diameter (125 mm center height): 250 mm Max. workpiece diameter with interchangeable pads: 350–500 mm Swiveling range of table in each direction: 10° Max. grinding length for flat surfaces (max. width = 200 mm): 900 mm Continuously variable hydraulic table speed: up to approx. 6 m/min Table reversal delay: 0–5 sec Grinding wheel for external grinding, diameter - width - bore: 400x50x127 mm Grinding wheel for flat surface grinding: 250x13x76 mm Wheelhead spindle speed: 1,500/1,700/2,200/3,600 rpm Wheelhead swiveling range: 270°, with indexing every 90° Codew U Ry Nspfx Afpopu Vertical travel of wheelhead, center height: 125–350 mm Transverse travel of wheelhead: 285 mm Hydraulic rapid traverse stroke: 40 mm Intermittent infeed of wheel by table reversal: 0.001–0.03 mm/dia Continuous infeed for plunge grinding: 0–0.9 mm/dia Micrometric infeed stop, by division: 0.001 mm/dia Workhead swiveling range: 360° Workhead spindle speed, stepless: normal/special: 20–400 / 10–400 rpm Internal taper of workhead/tailstock: Morse 5/3 Wheelhead motor: approx. 4 HP All technical specifications are given without obligation and subject to errors or omissions.

Condition: good (used), Year of construction: 1999, operating hours: 16,000 h, functionality: fully functional, machine/vehicle number: 650341, Year 1999 with Fanuc 18 TB – 3 axes XZB Marposs E30/E20 Country of manufacture: Switzerland Voltage: 400V/50Hz/3ph Dimensions: 410 x 220 x 190 cm Net machine weight: 5,000 kg TECHNICAL SPECIFICATIONS CNC control: Fanuc 18TB Intermediate Section Fixed intermediate section: grinding head R Swiveling section with manual indexing 2.5°: R / RS / UR / URS -210° to +30° Swiveling section with automatic indexing 2.5°: R / RS / UR / URS -210° to +30° B axis, resolution 0.1'': R / RS / UR / URS -210° to +30° Standard workhead Swivel range: -10° to (+100°) Spindle speed (continuous): 6 – 600 rpm Internal taper: MT5 Reducing sleeve: MT5/MT4 Short external taper fitting: DIN 55026 / Size 5 Permissible torque: 160 Nm Guaranteed roundness for chuck work Standard: 0.5 µm Option: 0.2 µm Workpiece weight between centers: 150 kg Cpsdpfxjw T Tb Ho Afpou Tailstock Taper fitting: MT4 Quill stroke: 50 mm / 2° Option: fine adjustment with correction (Ø +/- 150 µm) Grinding wheel data (max. speed) Diameter 300: 27 m/s Diameter 400: 35 m/s Diameter 500: 45 m/s UR Grinding Head Power: 9.2 kW / 12.5 HP Wheel mounting, left max.: Ø 500 x 80 mm Right, additional max.: Ø 400 x 63 mm Internal grinding device: spindle HJN 828 Lower table (Z axis) Distance between centers: 1000 mm Max. travel: 1150 mm Max. speed: 15 m/min Max. resolution: 0.1 µm Upper table Distance between centers: 1000 mm / swivel 0° to 9° Grinding carriage (X axis) Max. travel: 320 mm Max. speed: 7.5 m/min Max. resolution: 0.1 µm Pneumatics Min. connection: 6 bar Air consumption: approx. 0.6 m³/h Coolant Max. connection pressure: 3 bar Required space (version 1000): 3600 x 2000 mm Unless otherwise stated, technical data is provided without engagement and may be subject to errors or omissions.

Condition: refurbished (used), Year of construction: 2025, functionality: fully functional, machine/vehicle number: 1845/455, Completely refurbished: Mechanics, geometry, hydraulics, and electrical components Wheelhead Disassembly, cleaning of parts, replacement of worn and defective components, motor overhaul, replacement of bearings, replacement of belts, spindle disassembly, replacement of seals and O-rings, plus adjustment. New paintwork. Workhead Disassembly, cleaning of parts, replacement of worn and defective components, motor replacement, replacement of belts. New spindle bearings. New paintwork. Tailstock Disassembly, cleaning of parts, replacement of worn and defective components, motor replacement, replacement of belts. New spindle bearings. New paintwork. Internal grinding attachment Disassembly, cleaning of parts, replacement of worn and defective components, installation of the support and geometry alignment. New paintwork. Hydraulics Disassembly, motor replacement, hose replacement, defective and worn parts replaced. Hydraulic block checked. X-Axis Disassembly, replacement of worn items such as O-rings, seals, rings, etc., overhaul of hydraulic piston, regrinding of tables. Z-Axis Disassembly, regrinding of tables, replacement of worn and defective parts, overhaul of hydraulic piston, scraping of V and flat guides. New paintwork. Measuring system Digital 2-axis display included. Electrical cabinet Replacement of motor contactors and relay controls. New wiring. New variable speed drive (frequency inverter) for the workhead. TECHNICAL SPECIFICATIONS Distance between centers: 1500 mm Distance between centers (workhead to tailstock overhang): 1650 mm Center height, standard: 125 mm Center height with riser blocks: 225/250 mm Maximum grinding diameter: Ø 250 mm Maximum grinding diameter with riser blocks: 450/500 mm Cpedsxt Ilfepfx Afpju Table Usable surface: 2060 x 140 mm Max. length and width for surface grinding: 1750 x 200 mm Longitudinal travel, manual or hydraulic: 1750 mm Manual table movement, 1 handwheel revolution – coarse: 20.006 mm Manual table movement, 1 handwheel revolution – fine: 2.457 mm Table speed, continuously via hydraulics: up to 6 m/min Table swivelling: 6° Stop and return: 0–5 sec. Workspindle Workpiece speeds, continuously variable (electric): 20–400 rpm Swivelling: 360° Workspindle taper (internal): MT5 Tailstock Internal taper, tailstock spindle: MT3 Spindle retraction, manual or hydraulic: 30 mm Diamond dresser taper (internal): MT0 Universal grinding head Cross slide travel for wheel: 285 mm Rapid traverse for wheel slide, front and rear: 40 mm Grinding spindle speeds: 1500 – 1700 – 2200 – 3600 rpm Vertical grinding spindle movement, center heights: 125–330 mm Max. wheel for cylindrical grinding: 400 x 50 x 127 mm Max. wheel for surface grinding: 250 x 20 x 76 mm Head swivelling with locking at every 90°: 270° Wheel feed 1 division of the micrometer drum: 0.005 mm/Ø Automatic wheel feed, max.: 0.9 mm/Ø Motors Grinding spindle motor: 2,900 rpm / 4.0 hp Workspindle motor: 3,000 rpm / 2.0 hp Coolant pump motor: 2,850 rpm / 0.12 hp Internal grinding attachment Bore: 70 mm Internal grinding spindle speed Ø70 mm: 14,000 rpm Internal grinding spindle speed Ø50 mm: 21,000 rpm Subject to error or omission, the technical information is provided without obligation.

Condition: refurbished (used), functionality: fully functional, machine/vehicle number: 32461/2384, Manufacturing origin Swiss Voltage 380 / 50 / 3 Netweight 4900 lbs Dimensions 121 x 69 inches TECHNICAL DATA Nominal distance between centre 600 mm Max. distance between centres, headstock and tailstock projecting 750 mm Height of centres, standard 125 mm Height of centres by means of raising blocks for work head-and tailstock 175 =ᐳ 250 mm Max. swing diameter with 125 mm height of centres 250 mm Max. swing diameter with raising blocks 350 =ᐳ 500 mm Table swivels each side 10° Max. lenght for surface grinding (width=200 mm) 900 mm Table speed infinitely viable by hydraulic drive, approx. .. 6 m/min Dwell of table reversal 0 - 5 sec. Grinding wheel for cylinrical grinding (diameter x width x hole) 350/400x50x127mm Grinding wheel for surface grinding diameter x width x hole 250 x 13 x 76 Speeds of grinding wheel spindle 1500/1700/2200/3600 Cpoded Amifopfx Afpju Grinding wheel head swivels 270° with indexed stop each 90° Vertical movement of grinding wheel head, height of centres -350 mm Cross movement of grinding wheel head 285 mm Rapid advance and withdrawal of wheelhead 40 mm Intermittent infeed per reversal of table 0,001-0,03 mm/dia Infeed for plunge grinding 0-0,9 mm/dia Micro-corrector of infeed, 1 division of dial 0,001 mm/dia Swivel of work headstock 360° work speeds infinetely viable, normal/special 20-400/10-400 Internal taper of headstock/tailstock 5/3 Morse Grinding wheel motor, approx. 4 HP errors and omissions excepted data given without obligation Inventory Nr.2170089, machine equipped with : 1 Workpiece headstock MT5 1 sinus rule without comparator 1 Wheel headstock with 4 pulleys 1 Tailstock MT3 1 Collet clamping device with drawbar and reduction sleeve B32 1 Internal grinding device with quill Fischer UJ50x250 – pulley Ø 48 for 14000 min-1 1 Pivoting wheel trueing-up device with sole 50 mm 1 Table’s pivoting stop without comparator 1 Cooling device through decantation 1 extractor 1 balancing stake

Condition: used, Year of construction: 1995, grinding diameter 350 mm grinding length 1000 mm Cpjdpexyadaefx Afpeu centre height 175 mm Completely overhauled in 2013 Heavy duty workpiece headstock tailstock Without chuck and without bezel in the photo Kelco 90 control The machine can be viewed in operation at the customer's premises from 2025 up to and including January 2026.

Condition: used, Year of construction: 2021, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm Control Fanuc 31i Maschine aus 1998 jedoch 2021 überholt von Kellenberger inklusive neue Steuerung FANUC31 mit Blue solution Nur 790 Stunden Schleifzeit 1 UR-175 / 1000 Standardausführung (T1, T2, T6, T7) Cpsdex Rn Uwepfx Afpou 1 Schleifscheibenausrüstung T1 500x80x127mm 1 Schleifscheibenausrüstung T2 400x63x127mm 1 HF-Innenschleifeinrichtung T6 MFM 1224/42 42.000 U/min 1 HF-Innenschleifeinrichtung T7 MFM 1242/60 60.000 U/min 1 Spitzenhöhe 175mm 1 CNC Steuerung FANUC 31i mit Blue solution 1 Unrundschleifen 1 Remote Diagnostic 1 B-ACHSE CNC-gsteuert 1 Reitstock mit pneumatisch betätigten Pinolenrückzug 1 MIKROVERSTELLUNG: Reitstock Unterteil mit Mikroverstellung 1 Werkstückspindelstock mit C-Achse 1 Werkstückspindelstock mit schwenkbarem Unzerteil 1 KELPOS: Aktive Längspositionierung 1 Vorbereitung für Messsteuerungen Movomatic ESZ 400 oder Marposs P7 ME 1 KELSET : Werkzeugvermessungssystem 1 Grundmodul für Anschnittsensoren und Auswuchteinrichtungen Fluid-Anschnittsensor mit Magnetfuss 1 Vollverschalung Emulsion 1 Kühlmittel-Reinigungspistole am Tisch angeschlossen 1 Vorbereitung für Schleifnebel-Absauganlage Emulsion

Condition: used, 3 flanges for type 600 U – available for sale individually or as a set Codpfx Aox N Rytofpjpu